Addition of Cisco IOS Gatekepper to Cisco TMS
Hi people,
Does anyone has idea about adding Cisco IOS Gatekeeper for Cisco TMS. I tried it. added, but no luck. We use the TMS 13.2.2 and IOS 12.4
Thank you
Hi Jean Claude, please refer to product support 13.x TMS guide of
I don't see that Cisco IOS GK is tested with TMS.
BR, Mahesh Adithiyha
Tags: Cisco Support
Similar Questions
-
Cisco TMS taken in charge the list of endpoints
Is there an updated version of the supported Cisco MSDS list endpoints, as can be found here:
http://www.Cisco.com/en/us/products/ps11338/tsd_products_support_integra...
This document has been updated for Cisco TMS 13.2, and we are now at the time writing on CIsco TMS 15.1
I want to check if changes have been made between 13.2 and 15.1 of decline in support of endpoints, or support of the additional endpoints, including?
Thank you
Cisco stopped publishes the document after TMS 13.x MSDS product support, refer to the searching for information on the supported by Cisco TMS systems for more information. That said, you must reference it TMS Release Notes to see what support has been deleted and added in this output. You can also take a look at endpoint-support-tms-14-and-tms-15 for a list of example of endpoints wire is no longer supported Wayne created.
-
CUCM + MCU + CISCO TMS integration
I'm marching integration with MCU 4.5, 10.5 CUCM, sx20 and TMS 14.5
According with manual bellows
http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/infrastructure/MCU...
I ve done a Deploying an MCU as a multimedia resource for Unified CM.
MCU has a SIP trunk with 10.5 CUCM, MCU is recorded as the Conference on the multimedia resource.
SX20 Conference ad hoc works well with another 7 codecs.
My question is
I want to plan conferences by mcu or cisco TMS, but I am not able to do.
How can I integrate Cisco TMS or planning by MCU? It s not working not on my side.
Hello
Please see the following guide
http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/infrastructure/TMS...
HTH
Manish
-
Hello
I have some devices (2 CTS 3010, CUCM, GST of VCS - C and 3 2 1) managed by a Cisco TMS. I want to monitorate all devices to a network/system like HP OpenView management tool.
Is it possible to leave the TMS works as a server snmp / trap receiver, and transmit received traps to network management tool? In other words, is there a way to configure trap forwarding in TMS?
The TMS, I configured the IP address of HP's OpenView under network configurations, but it doesn't seem to work.
On CUCM, I configured the Ip address of the TMS as trap receiceiver.
Thanks in advance
Hello
TMS uses only SNMP interruptions for older systems (MXP, TANDBERG classic). Traps SNMP of newer systems (series C, CTS, MX, E20, SX20 etc.) and products (CUCM, VCS, MCU, gateways) network infrastructures are ignored by TMS. (it's not mentioned as well in the documentation, but I'll look in there clarifying). So no, you can't configure the transfer of trap in TMS.
But why do you need TMS to send traps to an external system; could not do of your endpoints send traps directly to the external network management tool?
Kind regards
Kjetil
-
can plan us the Conference from Outlook with Cisco TMS
Hi team,
is it possible to provide to the Conference by the prospect with Cisco TMS, we have no license to Exchange provisoning. Y at - it a plugin that can be used with Microsoft outlook.
Please advise.
See above for my response, either you need to purchase the license and install / configure Setup
or you program something yourself.
I would not exclude that there could be tools external hookin upward on the MSDS as well, but I'm not aware of anything.
The other way is to do it by politics, rent rooms and is a participant dials up to the
others or if the meeting is greater everyone connects the mcu...
-
Hello
I recently upgraded to TMS 13.2 and installed Exchange TMS 3.0.1. Installation and Configuration worked well, but no event is synchronized to MSDS. If I look at the log file, I see the following line:
Cisco TMS Server is not responding. Halting.
It seems that TMS Exchange is not able to communicate with the TMS. Setup worked well, and the TMS user is Super Administrator, so I don't think it's a problem of permission.
I have attached the journal exchange of tms with level Debug of the game.
Any ideas?
Hey
Using HTTPS or HTTP to communicate with the SMT server through the TMSXE service?
Also, I would look in the Windows event logs to see if there's something interesting here. Especially check the application + TMSXE the event logs. I Don t want to join here (it's for the TAC) but if you see something that could be linked to the issue, please let us know.
Otherwise, I recommend you get help from TAC on this since it is more appropriate for a deeper repair.
/ Magnus
-
Cisco TMS 14.4 "Ajax request failed...". »
Hi Experts,
I installed Cisco TMS 14.4, installing all makes them very well, but at the first connection, I had error in Pop - Up The Ajax request failed...
TMS ERRORCOOKIE {FF44A030-7F95-461C-8065-615FCE335F7B} var TMSError = {toggle: function (tableId) {var errorTable = $(tableId); errorTable.style.display = 'block';}} TMSElement.positionCenter (tableId); $('InfoTable').style.display = 'none '; }} Stop_Wait(); An error has occurred!
Please click the back button on your browser to return to the previous page or click here to go to the front page of TMS. If the problem persists, contact your administrator to TMS.You can see the image
Can someone help me
Thank you
Hello
It should be a more specific error message in the log - web.txt, located in the \data folder in the MSDS on your server installation directory. What did he say?
Kind regards
Kjetil -
where the Cisco TMS database knowledge guidance document?
The TMS Installation done doc refers to the following doc:
Cisco TelePresence Management Suite database knowledge tips
D14216
But I can't find it on CCO.
Does anyone have a copy of that PDF?
The copy that I named:
Guide to setting up Cisco TMS SQL database product
December 2010 D14216.01
A little outdated.
Rgds, Geert Folens.
Looks like it is available online:
http://www.manualslib.com/manual/408637/Tandberg-TMS-SQL-database-configuration-guide.html
-
Cisco TMS first activate Idle all sessions
Hello.
We have the video conferencing system with Cisco TMS, blades MCU 8420, Tandberg Gatekeeper and Cisco in the series C endpoint, MXP series etc...
This week we have problems with planning because when we planned to meet his past of in waiting for idle session direct and all sessions the codec says no connection.
never start the meeting on active sessions.
then that we end the session or meeting and reprogram this session and that begins at the current session.
IM verified the conectivity between Cisco TMS and MCU, Endponits its Ok.
rigth now we rebooted the server and MCU and the GA but when even continue the problem.
The cisco TMS its located in other areas with transit to WAN network. We reserve the bandwidth with QoS for video, voice and data for im MCUS and endpoints asking its required reserve BW TMS Cisco commands API, Https, Https and other protocols? the problem may be congestion in WAN networks?
This Protocol should ensure guarantee connect API orders end to end of Cisco TMS - MCUS and endpoints.
I appreciate your support.
Giacomo BR P.
I did not completely understand your description.
The communication is done on MSDS by HTTP or HTTPS, depending on your settings.
In general, I would say that the management / follow-up will also through these ports, I would
expect tickets with problems logging on your TMS.
I could look at the logs and see: is the Conference properly generated on the MCU.
is the dial in number okay, can the scope of endpoint the mcu, can the mcu reach end points.
y at - it something suspicious on the GK, conferences and any other reservation of port
on the MCU
-
TMS of Cisco 'Unable to access Cisco TMS' error
Hello
I have another problem with the server of TMS as well! On my Web interface, I get the message "Unable to access Cisco TMS - TMS Incorrect database version" detected! Someone has an idea?
What TMS version?
Is it a new installation or you migrate TMS and TMSPE?
This error is usually visible with the TMS upgrades/migrations when the SQL database is running an earlier version.
Difficulty, uninstall TMS and then reinstall it.
During the re - install, you will receive a prompt to upgrade the database. This should fix the problem.
-
In a separate post, I have something related to this, but I would like an answer by the morning when I wake up so I just made a new post.
So, I have synced up my TMS with my VCS and I can now click the Configuration tab and I was informed by a Cisco Expert here disable TLS and checking name of certificate and the crowd to get rid of the "error of HTTPS response" I had. I did a full synchronization on the TMS and VCS and now I have a message "error Code 401 HTTP response '. I unfortunately didn't write the exact words he said in red because I'm at home now to write this post and like a fool I did not write it.
However, I think this has something to do with the verification of the user? Isn't it?
Patrick, if you answer thank you very much for all the help.
Did you follow all of the steps in the TMSPE deployment guide?
I'm out of the city at Cisco Live, but a quick search of the forums, I found http-exception-after-migrating-tms-tmspe, might be something to look at. It is also a documented bug, CSCue48378.
How long did you all use TMSPE, he has already worked before all the recent questions you had?
-
Cisco TMS assigns a numeric ID for the MCU Conference Scheduler
Hey Cisco
I create a conference planner tms 14.6, the Conference is to create, but the digital ID is not available until this conference began.
picture attached
I need see digital ID before.
I've not being updated to 14.6 TMS, but in 14.4 and I'd be surprised if this had been changed to 14.6, you can specify a system to switch to the MCU, in which case the address is displayed as below in the screenshot;
or, you can find the address by locating the Conference in the conference control center, then place the cursor on the MCU and you should see a small window showing all the relevant address, as seen in the screenshot; below
/Jens
Please note the answers and score the questions as "answered" as appropriate.
-
Cisco TMS - Making Participant Important in circles of the Conference
We have a Cisco 5300 MCU. In the settings, there is a function to make a large participant. Which takes into account that the stronger participant even when we speak do not.
We have admins that installing and create conferences in MSDS. Is there a way to configure this option in the TMS at the Conference is, or at the Conference and not required to proceed separately on the MCU?
Hello
Yes, the appeal has to be active. So you can access the Conference through the CCC, right click on the participant and select 'set as Important. "
Concerning
Paulo Souza
Please note the answers and mark it as "answered" as appropriate.
-
Is there a simple way to remove an option entered into TMS key? Licenses provided us licensed 25 movi when it should have been 25 endpoint licens. We want to remove this movi with MSD clients license.
Sent by Cisco Support technique iPad App
Only through the direct modification of the SQL database. If SQL server was installed locally on the server by Setup, open a command prompt and do
Osql-s localhost\sqltms e tmsng d
You will get a prompt like 1 >
Enter the command below... replacing string with your current license key
delete from OptionKeys where key like 'string'.
go
Type exit to exit the osql tool.
If your SQL server server is installed somewhere else or a different instance name, you need to change the osql command (s specifies the address of the server... EI is to use windows authentication) or the use of SQL Management Studio. If you use an external SQL Server, what to be put in place can help you. If you are unsure, open tools TMS on the TMS server and review the database connection properties. They will tell you where the TMS database.
-
Cisco Telepresence Server/Cisco Telepresence driver/Cisco VCS - C / Cisco TMS license
A big problem with the fact that I'm stuck is licensing. Really, I have tried many things to find the solution for it, but could not.
I have actually made all of these servers (mentioned in the title) in my lab in preparation for the CCNP Collaboration certification at home.
I am not able to complete some laboratories due to license issue (I guess). Y at - it an option to get the demo license for all these servers?
I would be really greatfull if someone can suggest me the solution and/or the licenses required to complete all the stuff for my CCNP Collab tag.
Best regards
Dipak Singh
TMS and VCS - C when installed without licenses, are automatically set mode of demonstration/test with some availability of license to test with. If needing a VCS-E, you will need to do to your account manager and they should be able to get you the time limited licenses good because I think that 90 days.
Conductor Essentials is free, which means that you can install and get full functionality without the need of all licenses, but you are limited to 1 conference bridge and no grouping is allowed.
TelePresence Server require licenses to function, once again, reaching out to your account manager for this.
At the end of the day, you should reach to your account manager for all of this, as they should be able to help get timed license if you need.
Maybe you are looking for
-
I downloaded the network drivers for the computer, but no luck, there are 6 devices in Device Manager lacking drivers, any suggestions? would it be a bad NIC?
-
Re: Satellite C850D - impossible to get into the BIOS
I'm unable to access the BIOS on this machine. I tried (a number of times) by pressing the FN and F2 and FN and F12 keys while the Toshiba logo is displayed. Unlike the Satellite A500, I have, no prompt for keys F2 or F12 doesn't appear at the bottom
-
HP app: fixing scan documents
Hello I can reach only 1 scanned page of a document using the Hp application for ipad and I have 4 papers to send all around 29 pages long Thank you for your help
-
Cannot install the new version of AVG antivirus error oxcoo70643
Original title: I'm trying to load a new free version of avg, but I get an error code oxcoo70643 which says that they cannot delete wonderful versionI'm trying to load a new free version of AVG, but whenever I get this day it is said that the version
-
Updating the measures for Win - XP Pro, SP1 to SP3 (jump SP2?)
I do volunteer work 1/2 day per week for a small organization non-profit organizations with a very limited budget (almost non-existent). We work in the given space, but have free access to the DSL service. We have the following... 1 2000 computer HP