After you disable the built-in webcam, imaging devices disappeared from the Device Manager. How can I make it reappear if I can activate my webcam?

Similar Questions

• When you press the new tab, how can I get the homepage instead of the history of tiles?

  When you press the new tab, how can I get the homepage instead of the history of tiles?

  You can try this.

  • https://support.Mozilla.org/en-us/KB/new-tab-page-show-hide-and-customize-top-sites#w_how-do-i-turn-the-new-tab-page-off

  Instead of the parameter mentioned pref in about: blank, you can enter any site of your choice.

  Ex: encrypted.google.com

• After you disable the speakers in the Sound Control panel, how to re-enable?

  On Vista 64-bit with latest updates, in a hurry to catch a signal continuously with the sound only through headphones, I turned off one of the entrances in the sound control panel, which was the laptop speakers.  This was done by selecting the element and selecting Disable in the right click menu.  When I come back to this Board for re - activate the speakers, they are listed is no longer and are not doing a scan for the hardware.  How can we reactivated the speakers?

  The audio device is "SoundMAX Integrated Digital HD Audio", and the computer is a Lenovo Thinkpad T61P.

  Hello

  Right click speaker near clock - reading devices - right click in the area of the boxes - check see the disabled and disconnected devices. Select speaker, then on the right click lower properties check the settings for the active device usage and so on. Also do the same to set up in the bottom left of this box.

  I hope this helps.
  --------------------------------------------------------------------------------------------
  Rob Brown - Microsoft MVP<- profile="" -="" windows="" and="" devices="" for="" it :="" bicycle="" -="" mark="" twain="" said="" it="">

• FF 8 causes flash to not however with load after you open the Task Manager and open the plugin container folder, everything works fine

  New upgrade FF and all the flash based video site does not load and makes computer almost hang. After I open the Task Manager and go to the folder where is the plugin container, everything works back. I don't do anything at all after opening the folder.

  What kind of error is it? Its very strange. If all goes well, there is a fix for this.

  Another method would be to uninstall FF and install FF8.0 and not use the upgrade FF7.0. It worked for me.

• I have 93 tasks in the Task Manager, how can I reduce them?

  original title: I 93 HAVE of TASKS that are currently RUNNING UNDER TASK MANAGER, HOW CAN I REDUCE THEM AND how DO you KNOW WHICH ONES to save you?

  How can I do to reduce the number of running tasks and how I decide what tasks should be reduced?

  Hello.
  Try below link that can help you to solve your problem:
  Optimize the performance of Microsoft Windows Vista
  http://support.Microsoft.com/kb/959062
   
  Ways to improve your computer's performance
  http://Windows.Microsoft.com/en-us/Windows-Vista/ways-to-improve-your-computers-performance
   
  Get maximum performance from Windows Vista
  http://Windows.Microsoft.com/en-us/Windows-Vista/get-maximum-performance-from-Windows-Vista-from-Windows-Vista-inside-out
   

  You can also try to do a scan spyware/malware & virus in safe mode to ensure that your computer is not infected.

  http://www.Microsoft.com/en-us/security_essentials/default.aspx

• After you disable the new interface to tabs, all new documents are not open in a larger window

  Hello

  Yesterday I upgrade my Adobe 11.0.10 Adobe Acrobat Reader DC 15.010.20056 player. The tabs interface was pleasant enough, but there are still some limitations with this features, such as,.

  1 > no option to set no maximum. tabs in a single window,

  2 > tabs cannot organize, to be moved to a new window and several selected

  I want to disable the new interface to tabs via Preferences > General > open documents in the new tab in the same window (not checked), but after you turn off the new tabbed interface, all new documents open after the first document are not open in a maximized window, they always opened in a restored window.

  No matter what I do, it keeps - on the opening of the second new pdf in this one, restored windows are the things that I tried to overcome this.

  1 > right of the DC open Adobe Acrobat click in the task bar > Adobe Reader DC > right click > properties > run: enlarged - only the first document opened in maximized windows, documents later opened in the restored only, window that too seem to not work when I closed the last document in a restored window. Opening in the same window type is part of the windows operating system, it does all the time, "opens the entire application in the same way that they have been closed, either maximized/restored and the size of Windows too". Only the first one application window is open in this way, rest of the windows open is seems to be not supported by the operating system.

  2 > of this forum discussion https://forums.adobe.com/thread/435552?start=0 & tstart = 0 , I checked for the mentioned, registry keys

  HKEY_CURRENT_USER\SOFTWARE\Adobe\Acrobat Reader\DC\SDI

  the default value is - "bNullDocMaximized" = DWORD: 00000001 , "bMaximizeNextDocument" = DWORD: 00000001 and "bResizeOnOpen" = DWORD: 00000000

  Exchange only tried on the third button (the rest has been preset to required values) - "bResizeOnOpen" = dword: 00000001 - restart > no change > reset to its default value

  What to do now...?

  Thanks in advance

  Hi Gangatharran,

  Thank you for bringing this to our notice.

  We have recorded a bug for this and will share an update on the progress made in this thread.

  Kind regards
  Rave

• Windows 7 will not be updated after you disable the upgrade of Windows 10.

  Hello.

  We have a number of computers at work that all run windows 7 pro 64-bit. We cannot upgrade to Windows 10 because it is not compatible with our companies critical software.

  I disabled the update of windows 10 via;

  -Uninstall KB3035583

  -Installation of KB3065987

  -Start-up of "disable update" in group policy under admin template/windows components/upgrades

  He worked on all the computers except one. All other computers are updated to windows 7 with no request an upgrade to windows 10.

  Simply, a computer that will not update hangs on the screen of "check for updates". I ran the Microsoft fixit50123.msi to this topic.

  What other options can I try on this computer thugs?

  Hi Paul,.

  Thanks for posting your query in Microsoft Community.

  I understand that one of the computers will not update for Windows 10 and I appreciate the efforts made in the patches that you have already tried. Let me ask you;

  • This computer is connected to the domain?
  • What security software is installed on the computer?

  From now on, I would ask you to refer to the methods provided for in article below and check the status.

  You cannot install updates in Windows Vista, Windows 7, Windows Server 2008 or Windows Server 2008 R2

  In addition, refer to the suggestions provided by Andre Da Costa in the thread below link and check the status.

  10 Windows Installer error "WindowsUpdate_C1900101-20017.

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

• Password changed after you disable the login screen

  Then I disabled my login screen, today and now when I start my computer, it brings me to a page that said 'incorrect password' and then returns to the login screen. Then when I enter my password it does not work. It seems that my password has been changed somehow when I disabled the login screen. In the meantime I can use my fingerprint reader to log on, but if I were to ever lose a finger in the future I wouldn't be able to access my computer. So, how can I reset my password?

  Curiously the admins cannot change her password without having to type the current password, but they can change the password of any other account without knowing the password.

  Not true - see here:

  1. click on the start planet.

  2. type the three letters cmd in the search box.

  3. press on Ctrl + Shift + Enter

  4. click on "run as Administrator".

  5. type the following commands and press ENTER after each:

  NET user "Zach" 123456
  The command above will set the password of the account selected to 123456.

• Installation of CentOS on Dell R720 after you disable the RAID

  Hello

  I have this R720 Server I want to install CentOS 6.3. It has two 256 GB partitions that have been previously configured as a RAID-1 volume. I removed it because we must not RAID and just need performance when it comes to disk read/write. However, the CentOS installer does not recognize two physical disks. But if I configure the RAID-0 drives the installation program recognizes the discs. I do for the installation program to recognize the physical disks? Thank you.

  Mary Carmen

  What RAID controller do you use?  I assumes that you use the H710 PERC, which does NOT support non-RAID, so in order for everything to be presented to the operating system, you will first need to configure it in RAID.  If you don't want to use RAID (even as a RAID 0 drive), then you will need get another controller.  PERC H310 supports non-RAID (the other controller for the R720 options make too, but they won't work on Linux).

• After you import the MSWMM file in Windows Movie Maker, the system hangs

  MSWMM FREEZES (what a surprise)

  After opening MSWMM and import my project that the cursor movement will begin erraticaly i.e. movement one or two seconds after I try to point and the operation I required will take his time is erratic in the activation and the images are erratic when read.
  A minute or two later everything "freezes". I had to 'Leave' to turn the computer off, wait one minute, then restart. It's so bad now, I had to stop using MSWMM, it's useless and a great disappointment to me. When I exit MM the cursor is always random for about 10 seconds. How is the mighty Microsoft Corp. cannot challenge these problems and let us get our projects?
  All other times, the computer works fine. I have not downloaded anything to cause this problem. I've defragged, Spybotted Temp files deleted, disc error checked, tried different suggestions of Youtube, and restored hoping can solve it, no luck.
  I run WINDOWS XP, 128 processor ATHLON, 56 k MODEM, 1.5 GB RAM, 120 GB HDD, IE7, Service Pack 3.I have made 10 videos previously and had a bad light with MM before but he managed to cope, now that's too bad. So, does anyone have helpful suggestions to what I can do to fix this problem so I can continue with my projects, please?

  After opening MSWMM and import my project that the cursor movement will begin erraticaly i.e. movement one or two seconds after I try to point and the operation I required will take his time is erratic in the activation and the images are erratic when read.
  A minute or two later everything "freezes". I had to 'Leave' to turn the computer off, wait one minute, then restart. It's so bad now, I had to stop using MSWMM, it's useless and a great disappointment to me. When I exit MM the cursor is always random for about 10 seconds. How is the mighty Microsoft Corp. cannot challenge these problems and let us get our projects?
  All other times, the computer works fine. I have not downloaded anything to cause this problem. I've defragged, Spybotted Temp files deleted, disc error checked, tried different suggestions of Youtube, and restored hoping can solve it, no luck.
  I run WINDOWS XP, 128 processor ATHLON, 56 k MODEM, 1.5 GB RAM, 120 GB HDD, IE7, Service Pack 3.I have made 10 videos previously and had a bad light with MM before but he managed to cope, now that's too bad. So, does anyone have helpful suggestions to what I can do to fix this problem so I can continue with my projects, please?

  =======================================
  . MSWMM would be your Movie Maker project file if it is a
  complex big project that you have been working on for a while it
  can be to reach the limits of your system resources.

  Creation of several small projects is better than a large
  project. If you save all of them in the movie .wmv format you
  can import movie collected files and combine them into
  one final film.

  Also... it may be interesting to try to install IE8... I remember
  See the reports of users of Movie Maker who has
  with IE7. Personally, I went straight from IE6 to IE8.
  (FWIW... it's always a good idea to create a system)
  Restore point before installing software or updates)

  More information:

  Movie Maker 2 hangs and crashes
  http://www.Papajohn.org/mm2-issues-acceleration-and-codecs.html

  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• An internal system component has disabled the hibernation. How can I solve this? __

  > I went through all the steps and not the powercfg h on and it says this:
  > hibernation failed with the following error: the request is not supported.
  >
  > The following preventing hibernation on this system.
  > one or more older drivers are installed:
  > VgaSave
  > An internal system component has disabled hibernation.

  I was told of pilots video what is the problem of the VGASave but I have the latest drivers.

  Hello

  1 I want to erase the General corruption and repair/replace damaged/missing system files:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------

  A Fixit for Hibernate

  How can I enable hibernation on my Windows Vista computer?
  http://support.Microsoft.com/default.aspx/KB/929658

  How to reactivate the lack of Hibernate Option in Windows Vista?
  http://www.askvg.com/how-to-re-enable-missing-Hibernate-option-in-Windows-Vista/

  -------------------------------------------

  Check the settings (BIOS/CMOS) that you can start and ensure that this suite of lan, Wake on modem and
  similar are not enabled.

  Shoot sleep problems - hibernation
  http://www.computerperformance.co.UK/Vista/vista_hibernate.htm

  How to solve a problem of Mode for Vista and find a Solution
  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.html

  How to enable and disable Hibernation - you can try to disable and re-enable the it. http://www.Vistax64.com/tutorials/165508-hibernation-enable-disable.html

  How to restore the default power in Vista (and then go back and change as you wish)
  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  How to troubleshoot performance problems with sleep, hibernation and resume in Windows Vista
  http://support.Microsoft.com/kb/950686

  Panel configuration-Device Manager - look at the settings for the network card, WiFi, Modem power management.
  and other devices. (Double click on the device and the power management tab)

  Panel configuration-Control Panel Home view (non-conventional) in the top-right search pane
  type of hibernation - see turn Hibernate on / off

  All the default power plans and then set them as you wish.

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• I use a trial version now installed en. But it is used a bad Mailadres were you send the mail. How can I change

  I use a trial version now installed en. But it is used a bad Mailadres were you send the mail to check. How can I change this mailadres?

  Hi j. Middelhuis,.

  Please refer to the below threads where the same issue was addressed:

  Bad e-mail address to sign in to Creative Cloud Desktop, how to pass to my email address?

  Email verification to wrong address

  Kind regards

  Sheena

• White screen after you disable the primary monitor and secondary on Satellite

  Hello

  I tried to connect a LCD screen on my laptop, in the first place, I went to the Panneau--affichage--controle--avancees--controler--proprietes--device use settings: disable!

  This allowed secondary LCD screen but the most stupid thing, it is that when I wanted to return to the screen of my laptop that I followed the same procedure with the LCD.

  The result is that now the two are empty. Laptop screen turns white as soon as starts to load windows. Combination Fn + F5 didn't help. I also tried to get into windows in safe mode, but it has not been possible.
  Does anyone have any ideas?

  PLEASE, I BEG YOU.

  Thank you

  During startup in safe mode, the laptop charge only a current drivers and it should be able to see something on the screen.
  But if it is not possible and you are not able to deliver internal display on the screen, then I guess you need to start form the recovery CD and reinstall the OS :(

  The new facility is scheduled to replace all the display settings and the laptop should work.

• After you disable the UAC in win7, when I re-enable UAC, it does not appear the diaglog when an exe file do some administrator-level operators.

  the exe is a third party provided, microsoft exe and a few other third provoided exe works properly.

  can I reset the UAC or other methods and do all the functions of the exe correctly?

  Hello

  Here are a few Article

  Here and here

• After you install SP3 on XP Professional, cd-rom disappears from Windows, but it is still in the bios

  The computer is an HP running an Intel Pentium III. The CD is a model Samsung Combo Drive SM-304.

  There is no problem on SP2.

  Hi PhilWinfield,

  Try the steps listed in the link to the HP website and check if this can help below: http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=bph07146

  Other links for reference: how to solve common problems that occurs when a Windows XP-based computer cannot read a CD or DVD: http://support.microsoft.com/kb/321641