Aggregate bandwidth of Sg500 two stacking using two stacking ports?

Similar Questions

• How can I use the USRP to record a signal using its two RX ports simultaneously?

  Hello.

  I am trying to record a signal using two antenna cone. The reason that I need two antenna to cover the bandwidth (DC - 6 GHz). a single antenna covers DC - 300 MHz and the other covers 300 MHz to 6 GHz. so I need to use two RX port of USRP at the same time to record the signal. I have two questions:

  1. is this all USRP market capable of covering this frequency range?

  2. is it possible to use the two RX port at the same time to the signals of the records I described? If this is not the case, how can do?

  P.S. I have two NI2920 USRPs and two USRPs N210 in my lab.

  Thanks in advance for your time.

  Sam.

  Hi Sam,

  To answer your first question, the USRPs you can reach the bandwidth you want. There is not a USRP, to my knowledge, that can reach this range in a single device.

  Also note that you can only use RX convened for two different ports at the same time using LabVIEW and the pilot of the USRP. If you want to use the two lines of RX, you will need to run a session with a single line, close the session and then start a different session for your second RX line.

• 4250 - SX: use two control ports supported or not?

  4250 SX sensor, I have two monitor ports.

  -Is it possible to use both at the same time?

  -Are there restrictions?

  -Is it supported by Cisco?

  Thank you very much

  Kurt

  -Is it possible to use both at the same time?

  Yes

  -Are there restrictions?

  The total bandwidth of 2 interfaces must add in the performance audit.

  The IDS 4250 SX is assessed to 500Mbps so if you receive 350Mbps the map of SX, then only plan on sending 150mbps for TX standard sniffing port.

  -Is it supported by Cisco?

  Yes

  SIDE NOTE:

  Do not confuse the IDS 4250 SX with the IDS 4250 XL. The SX has a single card PCI SX, while the XL is a double SX PCI card with hardware acceleration built into the card.

  With the XL both SX ports can be used for monitoring (but the standard TX port on the motherboard cannot).

  Combined traffic both SX ports must not exceed the return of the IDS 4250 XL (1 Gbps).

  Sniff two XL SX ports is supported by Cisco.

• My USB to ethernet adapter works only if plugged into my MacBook Pro. I tried to use to start an expander USB (power strip), but this has not--a problem when you have only TWO USB ports ports! Any suggestions?

  My USB to ethernet adapter works only if plugged into my MacBook Pro.

  I tried to use to start an expander USB (power strip), but this has not--a problem when you have only TWO USB ports ports!

  Any suggestions?

  Juice what 'expander' did you use?

  What model of MacBook Pro?

  This is the Office Mac Pro forum. I asked that your post be moved to the MacBook Pro laptop forum.

• Use of ISE 3355 device of the two GigE ports

  I'll put in place six ISE 3355 3 devices in a data center in another 3. They just installed a new infrastructure of server using 5596 Nexus and Nexus 2248TP farm top of rack switches.

  I am looking for documentation on how to make the collection of NETWORK adapters on the way 3355 or some connect Gig0 to FEX101 and Gig1 to FEX102. Or simply set up a channel using LaCP port between the two different groups of FEX?

  Sent by Cisco Support technique iPhone App

  Hello

  This is not supported, you can not team or balance the load or use redundant interfaces on devices of the ISE. You can only use a span port dedicated for ISE deployments, or use the links to crossover to a deployment ipep in HA mode.

  Thank you

  Tarik Admani
  * Please note the useful messages *.

• I'm trying to connect two monitors and one using the hdmi port and the other vga. How can I get the pc to recognize the two?

  Original title: multiple monitors

  I'm trying to connect two monitors and one using the hdmi port and the other vga. How can I get the pc to recognize the two?

  Hi David,

  Thanks for posting your query on the Microsoft Community.

  I suggest you refer to the Microsoft Help Articles below and try the steps mentioned.

  Check out the link:

  http://Windows.Microsoft.com/en-in/Windows-8/how-connect-multiple-monitors#1TC=T1

  You can also check:

  http://Windows.Microsoft.com/en-in/Windows-8/get-best-display-monitor

  Hope this information helps. Please let us know if you need any other help with Windows in the future. We will be happy to help you.

• Two headphones can use the same ports? Or is there an exception with RAC?

  I was under the impression that the two processes of the listener cannot use the same port. But, how to scan LISTENER_SCAN2 and LISTENER_SCAN3 headphones use the same port 1628 in the RAC hump178 node?
  
  
  

  $ srvctl config scan_listener
  SCAN Listener LISTENER_SCAN1 exists. Port: TCP:1628
  SCAN Listener LISTENER_SCAN2 exists. Port: TCP:1628
  SCAN Listener LISTENER_SCAN3 exists. Port: TCP:1628
  
  
  
  $ srvctl STATUS SCAN_LISTENER
  SCAN Listener LISTENER_SCAN1 is enabled
  SCAN listener LISTENER_SCAN1 is running on node humpy179
  SCAN Listener LISTENER_SCAN2 is enabled
  SCAN listener LISTENER_SCAN2 is running on node humpy178
  SCAN Listener LISTENER_SCAN3 is enabled
  SCAN listener LISTENER_SCAN3 is running on node humpy178

  These 2 listeners, according to the ouput srvctl above runs on the humpy178 RAC node that has 1 single public IP address. It's just a normal (standard) 2 node RAC configuration.

  Listeners in cluster environment using virtual IP addresses.

  You can check it out yourself:

  lsnrctl status LISTENER_SCAN2
  lsnrctl status LISTENER_SCAN3
  

• Satellite C660 - two USB Ports without function (bad connection)

  Hello, sorry for the worst English.
  Historically, the touchpad of my Satellite C660-220 used without operation, worked with a mouse of radio. Now, two usb ports can only be used under certain conditions. Can I replace the connections for this part (motherboard / motherboard) for example, a computer used toshiba laptop? Where can I read, one of which models the parts required are the same as well?

  Best regards from the Germany

  Bert

  Hi Bert

  I guess for you that it is quite simple. Problem is that this repair is not supported, and all we can try it on its own, including all the risks of damaging something.
  > Where can I read, one of which models the parts required are the same as well?
  This kind of document is not and if it has information that is not for public use, but for only authorized services.

  Theoretically, you can find the same mainboard with damage CPU or GPU and use parts from there.
  Believe me it is not easy to give you some good advice on this subject.
  Out of curiosity, but you have some experience with these things?

• Satellite A500 - 14L cannot recognize two USB ports

  Hello

  I bought a Satellite A500 - 14L three months ago, I've just updated the bios with this link , but after two USB ports (on the left side of the computer) do not work.

  I try to download the new driver for them, but without success.
  Do anyone now how can I solve this problem?

  Thank you and sorry for the English, I'm French...

  Hello

  What operating system do you use?
  Is - this Windows 7?

  How about USB port State in the Device Manager?
  Is there visible yellow exclamation points?

  In your case I would recommend to check if all the necessary drivers have been installed.
  For example the Chipset Utility must be installed. It is very important.
  There is also the USB Sleep and Charge utility USB Sleep and Charge utility. This utility is able to activate or disable the USB Sleep function and fresh. It shows the positions of the USB ports supporting USB Sleep and Charge function and shows the remaining capacity of the battery.

  Please check these applications!

• Network ACL two specific ports

  As I know there is no way to set ACLs for network such that only two specific ports are available. I'm using Oracle 11 g 2.
  
  I would like a HTTP and SMTP port opened for local loop address. These are ports 7777 and 25. It is my understanding that you can have only one of the ACL for each host. While it seems that you can create others, any additional ACL for the same host does not always work as expected. So does anyone have tips that how can I do this? I'd rather not have all ports between 7777 and 25 available but this is what I currently have...
  
  DBMS_NETWORK_ACL_ADMIN. (ASSIGN_ACL)
  ACL = > 'local_loopback.xml '.
  , host = > "127.0.0.1"
  lower_port = > 25
  upper_port = > 7777
  );

  Captain Egg wrote:
  As I know there is no way to set ACLs for network such that only two specific ports are available. I'm using Oracle 11 g 2.

  Not the case in my experience. An ACL can be for a specific purpose, but contain multiple ports for this purpose.

  For example I assign ports 80, 8080, 7777 and some others, in a single web - acl.xml, to a target of network (host or domain).

  Read the usage notes in the PL/SQL package of database, Oracle®, and reference Types.

• HP Pavilion 15-n259TX (two Usb ports on the left does not work)

  I recently lowered the windows note 8 for windows 7 and found that the two usb ports on the left side of my laptop no longer works, that is, they do not detect anything, be pendrives or external hard drive. Can you help me fixed the problem?
  My laptop is HP Pavilion n259TX 15.

  Hello

  Install the driver usb 3.0 on the following link.

  http://ftp.HP.com/pub/SoftPaq/sp64501-65000/sp64965.exe

  Kind regards

  DP - K

• How can I configure two ethernet ports to connect to a VPN with Windows Server 2008?

  Something I can put in place, but im stuck with an error that I get is that I need two ethernet ports to configure vpn but why and how do I make it work I like

  original title: vpn windows Server2008

  In order to configure the VPN, you can take a look at:

  http://TechNet.Microsoft.com/en-us/library/cc725734 (WS.10) .aspx

• Suddenly, Dell U2311H monitor two usb ports not working after 4 years

  Hello

  I've had this U2311H monitor for 4 years now, and it is connected to the Dell XPS 8300 desktop.

  The monitor has two USB ports on the left and for some strange reason, than all the two has stopped working recently.

  I did the following:

  1. disconnect the power to the monitor cable, then plug it back in to the monitor.

  2. unplug the upstream connect the USB cable (between the monitor and the desktop) and re.

  3. move the USB upstream on a different USB port on the desktop while the monitor is off.

  Nothing helps. :(

  That I could do to make the USB ports on the monitor work? I lose 2 practical USB ports and kind of desperate.

  Thanks in advance!

  Jason

  If it was me and the U2311H seemed much, I would just get a card 4 ports USB 2.0 Hub and plug it into the XPS 8300.

• Should we two-way ports only in EMP?

  Hello

  I always asked customers to open the two-way port between the areas of Web and database without giving much thought, because I had seen it at Oracle. Customer claims now that I should be fine with only one open port direction that extends from Web to database because he says this is how it works in the EBS environment. I do not understand his logic.

  Someone please tell me how it is done at your end and is it mandatory to have the two-way port and why?

  Thank you

  Anjum

  It would be fair to the direction as indicated in the documentation of flow - http://docs.oracle.com/cd/E57185_01/epm.1112/epm_communication_flows.zip

  Example, if communicating with say a database the incoming port for example Oracle 1521 must be open on the database server.

  See you soon

  John

• stack of sg500x - you can LAG stacking ports?

  I have 2 questions to stack with the sg500x switch.  We have 3 of them.

  #1 question - can we stack LAG two ports together, in order to increase the bandwidth of 20gbps cell?  I would like the width of band increased, and you can LAG the regular ports of 10G together but the manual and the admin interface user does not appear to support two connections cumulation between two switches.

  question #2 - the manual says that you can configure all ports 10 4 regular ports or stacking according to the needs.  However, after digging a bit it seems that maybe it's a mistake in the documentation.  Elsewhere in the documentation, he mentions that by defining the configuration of the 'standalone' cell 2 stacking ports will be automatically retrieved as non-standard stacking ports.  Which explains how to get all the 4 configured as regular ports, but how do I set all 4 ports as stacking ports?  Of course, it does not matter with my setup if I can not LAG two ports stacking together.  My hope was to have 2 10 ports to each of the other 2 switches each switch.  Like this:

  Switch A S1 S2 & <->switch B S1 & S2

  Switch A S3 S4 & <->Switch C S1 & S2

  switch B S3 S4 & <->Switch C S3 & S4

  Hello Robert,.

  1. Unfortunately you can not DRAG stacking ports. The other port will be closed and act as a backup.

  2. I'll double check the documentation on this one, however, I can tell you that only a set of 10 G ports can be used as ports of the battery. As you mentioned, on its own, you can get back them for regular use.

  Could I offer as a suggestion - if you are really ready to get the link of 20G, you could set all switches to standalone and use several shifts between them. This would add extra work that each switch should now be configured individually, but it would allow you to complete your design.