Agilent driver causes LabVIEW jump and stop

Similar Questions

• Satellite L300 01:00 in WinXP-drive CD/DVD turns and stops alternately

  Hello
  I bought a new Satellite L300 01:00
  I installed Windows XP Home SP3 System (using nLite and driver of SATA Storage Manager) and all the drivers from the Web from Toshiba website.

  I have problem with CD/DVD drive (HL-DT-ST DVDRAM GSA-T50N):
  -copy of CD/DVD on the HARD drive looks like follow: for some data of time (a few seconds up to several minutes) are the copy; then drive slows down and stops, the copy is stopped, progress bar doesn't move; After 1 minute for example the drive begins to spin and copy the next part of data. Sometimes the system stops to answer and it should reset the computer, sometimes computer restarts automatically.
  -listen to the audio CD music and watch DVD movies look like, it is easy to imagine...
  -uninstaling DVDRAM in Device Manager and reboot system helps a bit, i.e. the copy time becomes a little longer..., sometimes the problem occurs with the next CD/DVD in the drive
  AudioSilencer - don't change anything
  -write on CD/DVD is also impossible - progress bar stops after 1-2 minutes and nothing happens. Yellow led is always on and the shutdown process, you need to restart the system.

  What is interesting, drive works perfectly with the latest Debian LiveCD...

  Someone at - it ideas?
  Thanks in advance
  Jan

  Hello

  I m wonder if you have installed the drivers SATA too?
  Did you?

  Please check in _device nursery-> Controllers IDE ATA / ATAPI-Primary IDE Channel-> properties >-> advanced Settings_
  If the + transfer mode + has been defined on * DMA if available *.

  Furthermore the + device + type must be defined on * auto detection *.

• Cable HDMI between HP g6 and HDTV cause an overheating and stop?

  I tried two HDMI cables for 3 years, HP Pavilion g6 connect with HDTV. Both are HP overheating and stopping. He worked a year ago but old broken cable. I dusted off by fan below.  I tried to watch a free movie on HULU.  Not overheat when using the case.

  Hi there @kathcat,

  Welcome to the Forums of HP Support!

  The quick answer to your question is clearly yes, because you are experiencing it. However, it should not cause this problem, and it is a symptom of a different problem. So the real question is why it arouses your laptop overheating?

  As any type of electrical connection, it will draw current through your computer, and if your energy consumption is already high for other reasons, this will increase your level of heat.

  I understand this as an info.

  Why computers generate heat

  And this will help to show the things that you can try, to help reduce heat, including cleaning.

  Reduce the heat inside the PC to avoid overheating

  Also, if you post the complete product number, I can look for the correct service guide which should include disassembly instructions, that will certainly help with cleaning as long as you're careful and follow all instructions to avoid accidental damage.  How can I find my model number or product number?

  Let me know if this helped.

• possible bug in Agilent ENA series LabVIEW Plug - and - Play (project-style) Instrument driver

  think I found a bug in this driver and I wanted to get confirmation.  (Here's the link to the driver page, to help locate the driver):
  ( http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=74D1F1D4EB5268E8E04400144FB7D2...)

  The VI in question is public > Action-status > configure > marker Configuration > Configure Marker.vi.

  The question that I saw was that the marker was not be set to the frequency transmitted to the VI.  (The parameter named 'Stimulus'.)  I looked at the guide to the programmer for the Agilent 5071 B and decided that the format of the SCPI command string should probably:

  %.;:Calc%ld:Mark%ld %s;
  : CALC % ld: % ld MARK: X % lf

  The ": X" had disappeared but seems necessary.

  Can this be verified?

  Thank you for taking the time to look at it.

  -Joel

  Snood1,

  I took a glance at the driver and manual of the programmer. It seems to me that the driver behaves as described in the manual should. Configure the Marker.vi use the following string to format the command:

  %.;:CALC%ld:MARK%ld %s;
  :CALC%ld:MARK%ld:X %lf
  

  Is that what you see too? Looks like that's what you added yourself. What was the previous text? This is the text that was there when I downloaded the driver. When it is interpreted, it looks like this

  :CALC1:MARK1 OFF;
  :CALC1:MARK1:X 0.000000
  

  As described in the ENA series Programmer manual, the first turns of the line of the marker reads OFF (page 283). The second line sets the value of the marker 1 (page 295) stimulation.

  Let me know if this looks OK to you.

  Kind regards

• Display driver hangs on the computer and the error message "display driver NVIDIA Windows Kernel Mode Driver Version 306.97 has stopped working and recovered."

  Original title: NVIDIA Windows Kernel Mode Driver Version 306.97 display driver has stopped working and recovered.

  Hiya,

  I have recently installed Windows 8 Pro, installed all of my usual applications etc..
  The problem I've encountered is maintaining display driver crashing. Or have waiting periods. The exact error message reads;
  "Display driver NVIDIA Windows Kernel Mode Driver Version 306.97 has stopped working and recovered."
  Until now it expires randomly even when the computer is idle, and more frequently when I watch videos online. Also, watch a clip full screen on some sites like YouTube is ok, but on others, it is very laggy (updated maybe once per second the image) and the sound is out of sync.
  I can't find a way to properly uninstall the graphics driver.

  At least yours is working semi... I have the GTS 450 (uses the same drivers) and the mine does not at all... Stuck with the regular game pilot integrated ATM and can not all games... Microsoft told me to wait a few weeks and for the reminder and Nvida said 10 ways to uninstall and reinstall the drivers for same. Hope someone with to get a fix for this soon.

  Hi guys,.
  Looks like this isn't just me.
  Just an update, that I can not confirm it as a solution, but I have not encountered any problem (a little screenlag aside) since the installation of the drivers beta. For me, the beta version of the driver is 310.33, R130. The only other change to my system updates Adobe Flash version packaged with Google Chrome to 11.4.31X to 11.4.402 to eliminate serious problems when you watch the video in full screen.
  Information system;
  Operating system: Windows 8 Build Pro with Media Center 64-bit, 9200
  CPU: AMD FX-8150 eight physical cores
  GPU: ASUS NVIDIA GeForce GTX 560 TI
  Main hard drive: OCZ Vertex 3 120 GB
  It may be useful
  Edit: Still not falling down, 11/02/12, 4 days
  
  
  New edition;
  
  
  If you still receive the error message, try the following steps;
  Has. try to perform a clean installation of the driver.
  Download the latest drivers for your graphics card. Run the downloaded file, and select "Custom Installation". In the next screen, you will see a checkbox or similar labeled "Clean Install".
       
  
  You can do so by visiting nVidia Driver Downloads (www.nvidia.com/Drivers). Automatically detect the right driver or download using the form. The best way in my opinion is to use the GeForce experience, who will do anything for you in two clicks and a reboot.
  B. close all other programs
  It is possible that the error was caused by too many programs that need to use the resources provided by the graphics card/chip. It is also possible that a certain program caused a conflict that pilots crashed.
  You can try closing some currently open programs one by one and see if the error persists, or restart your system with disabled startup programs and allow them one by one to find the culprit. If the error is too persistent to do the above, it would be easier to start in safe mode option.
  More information can be found below
  http://support.Microsoft.com/kb/2665946/en-us

• Jump in the middle of an audio track streaming on various sites causes the stuttering and audio glitch

  Hello

  Please refer to this thread for support on the technical support of SoundCloud forums. The thread contains all relevant information, including videos of the screenshots problem and console, made by myself and others. https://www.soundcloudcommunity.com/SoundCloud/topics/skipping-to-the-middle-of-a-track-causes-stuttering-and-glitchy-audio-chrome-Firefox

  In short, when you try to move forward for streaming audio, there is a memory buffer/stuttering problem that prevents a correct reading of the track. This problem is confirmed on SoundCloud and Traxsource and other people in the support thread mentioned Mixcloud and other streaming sites. In other words, it is not the special streaming service fault or another.

  The problem does not occur in Microsoft Edge, Internet Explorer or Chrome. Well, to clarify, when the issue was published on SoundCloud support forums, Chrome was having the same problem. However, they made a version a few days ago thrust, that fixed it.

  Here's my original on the SoundCloud support post (less), which has the relevant details. Note that we have updated both Flash and Firefox recently, so although I have mentioned earlier in my original post, everyone involved has since updated their browsers and Flash.

  From now on, the only solution for the problem is to go back to Firefox 40.0.2. Thanks for any help =)

  Matt

  Original message =.

  Jump in the middle of a track causes the stuttering and audio glitch (Firefox).

  I am running Windows 10 Pro.

  There seems to be a problem of caching that affect reading - I started noticing this problem three or four days ago. Previously, I could jump through my feeds at will, go straight until the middle of the tracks or mixes of listen seconds and determine if I liked the track. Now, I can't do it on Firefox 41.0.1. The problem is simply annoying on songs that are 3 or 4 minutes in length, as I must leave "cache" maybe ten seconds before jumping. Unfortunately, the problem is a game-breaker on mixtures which, for example, are 90 minutes long. If I jump to a point directly in the middle of the combination, nothing happens. The play button alternates between the 'Play' symbol and the symbol of 'Caching' ('... "), and so audio resumes, it is glitchy and consists of different parts of the track being played at the same time.

  I've eliminated my internet connection as the source of the problem by loading on board. On the edge of 20.10240.16384, the problem does not exist. I can scroll down to any mix of 2 hours in my stream, click on the middle of it, and the audio starts right up. No caching, without stuttering or glitching.

  I drove back Flash version 18 to see if it solved the problem in Firefox, but it did not. The problem persisted, so I re-updated to Flash 19.

  Yes, I understand how all versions and updates to work. I meant it as a generation of powder magazine. My bad.

  I consider this problem to be solved. Several different pre-release versions of Firefox have solved the problem; I have personally used both of them that work perfectly. A representative of Bugzilla stated that the patch will be integrated into Firefox 42, which will be released on 3 November.

  https://www.soundcloudcommunity.com/SoundCloud/topics/skipping-to-the-middle-of-a-track-causes-stuttering-and-glitchy-audio-chrome-Firefox?topic-reply-list [Settings] [filter_by] = all & question-answer-list [parameters] [reply_id] = 16269116 #reply_16269116

  I now consider this private matter. Thanks to all of you who have been here =)

• HP Pavilion x 360: back issues of sleep and stop; MEI driver moved

  I have upgraded to Windows 10 last summer and, like many people, I had sleep and close issues. The computer wouldn't wake him up after he went to sleep and when I stop the computer the light remained on and the fan will continue running. I was able to fix by updating the graphics card and the driver of MEI.

  Windows has released a new update a few days ago and it has been applied automatically to my computer. Now, sleep and shutdown questions have returned.  This time, the graphics card is fully updated, but now I can't downgrade my MEI driver back to version 8.1 of Windows ( 9.5.24.1790 1.5 M ). When I try to install the driver it says 'Setup progam was able to start one or more application processes' and stops. I tried running the installation through Setup of HP and download directly, and none worked.

  Does anyone else have this problem? Any advice?

  Open Device Manager, expand the 'System devices' section, and then find "Intel Management Engine interface", double click it and go to the driver tab, and then click on "roll back driver" button, it will come back to the previous driver.

  You can do most any device in the device manager driver.

  If roll back driver button is gray, then there is no older driver to restore.

• MacBook Pro slow and stop, memory or HARD drive or motherboard?

  These last few months my Macbook Pro medio 2012 begins to slow down. I was thinking of a resettlement but has not had the time yet.

  Last month, he really slow started to freeze and stops instantly. It reboots and then I get a gray screen saying with the icon (a card with a questionmark in there) that it cannot find the boot disk drive. I close it again with the button and restart, then it starts normally. This would have me believe it has something to do with my HARD drive or the motherboard, but then again I'm not a tech guy so I guess just really. Then I got the idea to do a test of material, with this error as a result: 4MEM/62/40000000: 0x81d97590

  After searching the Web, it would mean that my memory would be bad/broken. I read in another post to download an app called 'Remember' which tests your RAM. I tried yesterday and it worked fine, nothing was wrong. But today I did once again when my Macbook was slow functioning again and went to do some other stuff. When I came back my Macbook has a black screen, a Word to insert a boot disk. I just stopped and restarted again and started normally. It is a little slow to clear grey screen with the apple logo.

  So my question is, does anyone know where the shoe pinches, RAM, HARD drive or the motherboard? Will also contribute to a reinstall? Can I check if my RAM is always placed properly or is maybe dirty? I use an application called memory monitor for clean working memory from time to time. I'm updating to El captain, wanted to do it instantly when I want to do a clean install on my mac, but I think I'll wait with that I know where the problem lies.

  Really hope someone can help me!

  Kind regards

  Mike

  This was the report on closing down:

  accident report

  Anonymous UUID: 2DD0FAD1-4D38-B739-F019-9F395B5DB6AD

  Sam Nov 28 17:54:55 2015

  Panic report *.

  panic (cpu 0 0xffffff80037c127e appellant): "launchd died\nState to the last Exception:\n\n"@/SourceCache/xnu/xnu-2782.50.1/bsd/kern/kern_exit.c:363.

  News of the UUID:

  uuid = 0x7fff61d7e000

  uuid = 0x108fa1000

  uuid = 0x108ff1000<4396b358-725e-3ec0-bcbb-e4bf75fe1fb0>

  RAX: 0 X 0000000002000001, RBX: 0000000000000006 RCX 0 X: 0X000000010A2800E8 RDX: 0 X 0000000000000000

  RER: 0X000000010A2800E8, RBP: 0X000000010A280190, IHR: 0X000000010A27FF40, RDI: 0 X 0000000000000001

  R8: 0 X 0000000000000000, R9: 0X0000000108FE09F0, R10: 0X00007FFF91399B02 R11: 0 X 0000000000000206

  A12: 0 X 0000000000000000 R13: 0X00007FFF9688D7E0, R14: 0X000000010A2805D0 R15: 0X000000010A280790

  RFL: 0 X 0000000000000206, RIP: 0X00007FFF9139795A, CS: 0 X 0000000000000007, SS: 0 X 0000000000000023

  Wire 0xffffff8021e8a970

  0x00007fff9768fdab

  0x00007fff9768fec8

  0x00007fff976893b4

  0x00007fff9c109a6c

  0x0000000108fcf907

  0x00007fff96a7de73

  0x00007fff96a80dc7

  0x00007fff96a80a1c

  0x00007fff942c5a9d

  0x00007fff942c33dd

  0 x 0000000000000000

  Wire 0xffffff80220c1798

  0x0000000108fb8c91

  0x00007fff96a7de73

  0x00007fff96a815cd

  0x00007fff96a81030

  0x00007fff96a80bef

  0x00007fff96a80a1c

  0x00007fff942c5a9d

  0x00007fff942c33dd

  0 x 0000000000000000

  Wire 0xffffff8021e8a000

  0x00007fff96a8226e

  0 x 0000000000000000

  Wire 0xffffff8021fb15c0

  0x00007fff96a81925

  0 x 0000000000000000

  Wire 0xffffff803a4bd000

  0x00007fff96a8a4e6

  0x00007fff96a8293b

  0x00007fff96a813bc

  0x00007fff96a81030

  0x00007fff96a80bef

  0x00007fff96a821a3

  0x00007fff942c605a

  0x00007fff942c5fd7

  0x00007fff942c33ed

  0 x 0000000000000000

  Wire 0xffffff8037edb2e0

  0x00007fff8fbeaf1a

  0 x 0000000000000001

  0x00007fff61d8a475

  0x00007fff907537b5

  0x00007fff9765e648

  0x00007fff9688d7e0

  0x00007fff9688fddf

  0x00007fff96a7de73

  0x00007fff96a7e8ca

  0x00007fff9688e0a7

  0x0000000108fcc393

  0x00007fff96a7de73

  0x00007fff96a815cd

  0x00007fff96a81030

  0x00007fff96a813bc

  0x00007fff96a81030

  0x00007fff96a80bef

  0x00007fff96a80a1c

  0x00007fff942c5a9d

  0x00007fff942c33dd

  0 x 0000000000000000

  Wire 0xffffff8025fd2e28

  0x00007fff942c33dd

  0 x 0000000000000000

  Mac OS version: 14F1021

  Kernel version: kernel in Version 14.5.0 Darwin: kills Sep 1 21:23:09 PDT 2015; root:XNU-2782.50.1~1/RELEASE_X86_64

  Kernel UUID: 06D286E3-A8A1-3BE7-A7EB-EAC6E0C69758

  Name of system model: MacBookPro9, 1 (Mac-4B7AC7E43945597E)

  an application called 'Remember' which tests your RAM. I tried yesterday and it worked fine, nothing was wrong.

  This is not the right way to think about memory problems. When the test of the RAM ALL said that there is a problem, it's the truth. RAM problems are very difficult to isolate, and a diagnostic runs, but can't find the problem, if NOT "nothing was wrong" which is "he cannot find the problem immediately."

  This isn't a mystery. DIMM RAM, not another thing is more likely to fail. Then you could try Rember running all night, you could try to remove one of your DIMMs and see if chess stops, you can try to get a new DIMM and see if they work better.

• ProBook 455 L3P93ES G2 #ABZ: installation without end and return the video driver AMD R6 and R7 M260DX and stop on a black screen system

  Hello, I'm in trouble with this problem. If anyone can help me, I appreciate a lot. Thank you in advance.

  Laptop: HP ProBook 455 G2 L3P93ES #ABZ

  Problem: windows back AMD R6 and R7 video driver to the old version of windows update install. Return process the screen come black and stop here.

  Procedure, I followed:

  1. updating the bios with the latest version (M75_0141.bin)
  2. new facility created by HP Cloud recovery customer USB boot disk
  3. Install the drivers and programs of the HPSoftwareSetup.exe util
  4. Connect the network cable and upgrade the drivers and the HP Support tool programs assistant
  5. Install the software
  6. Join the Organization's domain
  7. Force Windows Update to version 1607 by the upgrade of Windows tool
  8. Windows Update

  Item 4, at random, windows update 10 and return the driver from these versions:

  • 15.201.1301.0
  • 15.201.2301.0
  • 15.300.1025.1001

  I don't have install the AMD specific video driver (Radeon Crimson Edition 16.7.3 software) or drivers from the Chipset AMD (Crimson edition 16.7.3) because when I try in a previous installation of test I had the same problems

  To restore the display I have to start windows in safe mode and disable the two R6 and R7 display cards, and then restart. After that I can reactivate the cards one time.

  This device first question first time I install Windows 10 the year in August (Yes, after a few days Windows 10 out)

  Any help that will be much appreciate because I have to reinstall on 20 laptops for the school to start the day.

  Thank you

  ScuolaCarovana

  Hello;
  
  Let me welcome you on the HP forums!
  
  From your description, it seems that, after you have installed the correct video driver for your ProBook (15.201.1301) AMD, Windows Update is then by installing a different driver on top of that, right version?

  If this is the case, you must follow these instructions to STOP Windows update update drivers: how stop Windows 10 to update automatically the device drivers - windows Windows 10-10

  Once you do this, you should not see updates to the pilot after that.

  Good luck

• I get the message "app Incredimail has stopped working, a problem caused the program will stop working - Windows will close and inform you with a solution.

  When I try to open Incredimail I get the message "Incredimail application has stopped working, a problem caused the program will stop working - Windows will close and inform you with a solution ', I have used as my e-mail for several years and never had a problem before Incredimail client.  I have gmail for my email.  You are able to help with this problem?  Thank you, June Fleischmann - my email address is * address email is removed from the privacy *

  I suggest to see if there are updates or new versions available for IncrediMail.

  If still no luck, I suggest to ask the support of IncrediMail

  I hope this helps.

  See you soon,.

  J

  

• KB2286198 Windows Update causes Windows Live Messenger stops responding and crashed.

  After believing that my computer has somehow a virus and spend hours trying to solve the problem, I think that an update is causing the problem: I solved it by following these steps:

  KB2286198 Windows Update causes Windows Live Messenger stops responding and crashed.  Resolution: restore to before the update has been activated Windows installed updates and hid the update, so it would not automatically reinstall and the program works.  Please, difficulty of the update or rewrite it.  I can't imagine that I'm alone on this breaks.

  You will find support for Windows Live Messenger in these forums: http://windowslivehelp.com/forums.aspx?productid=2

  You can find support for the installation/uninstall/upgrade / upgrade to Windows Live Essentials in this forum: http://windowslivehelp.com/forums.aspx?forumid=a372972e-8e7a-4d85-adc3-a1b43e8c02ec

  Note: In the not-too-distant future, Windows Live Essentials 2011 QFE2 will be a mandatory update.

• The drive on my Acer Z5610 is overheating and stop. How can I transfer my Windows 7 on new HARD drive

  Would appreciate help from the members of the Forum.

  The drive on my Acer Z5610 is overheating and stop unexpectedly. I bought a new 1 TB WD HARD drive. I tried loading the Acer recovery CD 3 I initially created in order to load all applications touch etc, but received a message to say that I got at loading Windows. The computer came pre loaded with Windows 7 Home Premium, so I did not all Windows disks. My question is: How can I transfer Windows 7 on my new HARD drive so I can begin to rebuild the PC?

  Hello

  I think that you have created the driver & application backup, if this is the case & * if the old HDD is still detected & boots you could create a factroy restore discs, if not then you might even get to store.acer.com.

• display driver intel graphics accelerator driver for windows Vista (r) stopped responding and has recovered?

  I recently formatted my laptop (fujitsu siemens) and she ALWAYS had windows 7 installed inside. However, since I formatted, sometimes white people just screen out and I get the message:

  display driver intel graphics accelerator driver for windows Vista (r) stopped responding and has recovered?
  Any ideas what could be going wrong?

  Update all the drivers on Fujitsu support site, for your model

• I recently had to reimage my hard drive and need to reinstall CS5. When I do I get an error stating: another instance of deployment is already running. I tried to get back into market and stop before trying again to install.

  

  I recently had to reimage my hard drive and need to reinstall CS5. When I do I get an error stating: another instance of deployment is already running. I tried to get back into market and stop before trying again to install.

  I tried several times to reinstall without success.

  Help, please.

  Hi John,.

  Scott, please see the steps mentioned in the link below.

  • Resolution of error messages. CS5, CS5.5 bootstrapper

  It could be useful!

  Rayyan

• J K L shuttle keys causing Premiere Pro to crash and stop. Someone having this same problem?

  J K L shuttle keys causing Premiere Pro to crash and stop. Someone having this same problem?

  Hi Abraham,.

  Sorry for this question.

  Changing the audio channel seems to be the cause of my problems. I have change audio channels on the video for my project it to appear on my preview window use J K L to Polish thru and it hangs and stop.

  This looks like a problem that we know. You can avoid collisions by turning off 2 Audio Preferences:

  • Maintain the pitch audio when the shuttle
  • Outputs multi-channel sum to Mono in the Source monitor

  See if your situation improves after the deactivation of these preferences.

  Thank you
  Kevin