Aironet 2600 series AP (AIR-CAP2602E) to stand alone
Hello
I bought the AP incorrectly, instead of getting the "Standalone/standalone" version (AIR-SAP2602E), but I bought the controller-based version
(AIR-CAP2602E); My question is that I can use 'ap3g2-k9w7 - tar.152 - 2.JB.tar' too flash to a standalone "Standalone /?
If Yes, can anyone help to POINT me to the "Flashing method" right and necessary things like cable from the console or just "ethernet cable" will do? Enjoy it!
When you download the image, if you hover your mouse over the name of file, a pop up appears with MD5.
Sent by Cisco Support technique iPhone App
Tags: Cisco Wireless
Similar Questions
-
Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?
Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?
I have (2) AIR-SAP2602I-A-K9, configured the same way.
on two different remote LANs.
They don't seem to be handing out addresses via DHCP.
{If I connect to a local network with another DHCP server}
wireless devices can obtain addresses
This another DHCP server on the LAN through the access point.}
I followed 12.4.25d. JA.cg.pdf
Configuration of the Access Point to provide the Service DHCP 5-22
---------|---------|---------|
e.g. 3444-RCS1-AN #show running-config
Building configuration...
version 15.2
3444-RCS1-YEAR host name
no ip Routing
USH - DM IP domain name
DHCP excluded-address IP 192.168.29.89
IP dhcp RCS1 pool
network 192.168.29.88 255.255.255.248
router by default - 192.168.28.1
Rental 1 0
interface BVI1
IP 192.168.28.211 255.255.254.0
no ip route cache
default IP gateway - 192.168.28.1
---------|---------|---------|
---------|---------|---------|
e.g. 3444-RCS2-AN #show running-config
Building configuration...
version 15.2
3444-RCS2-YEAR host name
no ip Routing
USH - DM IP domain name
DHCP excluded-address IP 192.168.129.81
IP dhcp RCS2 pool
network 192.168.129.80 255.255.255.248
router by default - 192.168.128.1
Rental 2 0
interface BVI1
IP 192.168.128.171 255.255.254.0
no ip route cache
default IP gateway - 192.168.128.1
---------|---------|---------|
Thats the DHCP Pool range 192.168.29.88 through 192.168.28.95
Well this will confuse your customers.
And this is NOT how to set up your "range". See below:
DHCP excluded-address IP 192.168.29.1 192.168.29.87
DHCP excluded-address IP 192.168.29.96 192.168.29.254
IP dhcp RCS1 pool
network 192.168.28.211 255.255.254.0
router by default - 192.168.28.1
Rental 1 0
-
Deployment options for Aironet 2600 series
I got a 2600 (AIR-CAP2602E-A-K9) and wanted to know if we should use a cisco regulator or can be used as a stand-alone wireless unit AP? Depending on the response, I may have a follow-up question.
Thank you
I received a 2600 (AIR-CAP2602E-A-K9) and wanted to know if one has to use a cisco Controller unit or can one use the AP as a standalone wireless unit?
The AP can be converted into stand-alone. Currently, the product ID States that it is running IOS based controller. To convert offline, read this: you use a server TFTP to return to a previous version
-
Trouble getting a Cisco 2600 series AP to stay connected to WLC 5508
Hello
I recently loaded the independent our old APs upgrade to LWAPs. We have a WLC 5508 to our Virtual Co - Lo and I use Flexconnect to accommodate local switch and dhcp on our sites. I have updated more than 50 APs and joined them to the controller. These include only the 1130AG and 1240AG models. However they work perfectly and stay connected to the controller. I'm having is with a new batch of 2600 series APs stay connected to the controller. I tried to do research in what may cause disconnect it but have yet to find a solution. I use DNS to resolve queries for CAPWAP & LWAPP APs to the controller on our EXTENSIVE network. Read other messages I thought that this is perhaps a problem with packages to drop but have had our provider that manages Sonicwalls at both ends of the WAN confirm for me that there is no packet loss. Here are the logs that I collected through the puttty of the WLC & AP. Any help would be greatly appreciated.
AP, I do the test on:
NAME: "AP2600', DESCR: 'Cisco Aironet 2600 Series (IEEE 802.11n) Access Point.
PID: AIR-CAP2602I-A-K9, VID: V01, SN: FTX1740J8V1
WLC in question:
Name of the manufacturer... Cisco Systems Inc..
Product name... Cisco controller
Version of the product... 7.3.112.0
Bootloader Version... 1.0.1
Retrieving Image Version field... 6.0.182.0
Firmware version... Console USB 1.3, 1.6 Env FPGA, 1.27
Build Type....................................... DATA + WPS
System name... wificontroller
Location of the system... Corp
Contact System... Net engineer
ObjectID of system... 1.3.6.1.4.1.9.1.1069
Redundancy mode... People with disabilities
IP Address....................................... 10.250.32.8
Last Reset....................................... Software reset
Time system... 190 days 3 hours 34 minutes 24 seconds
Location of the time zone of the system... (GMT - 5:00) Eastern (USA and Canada)
The country is set... USA - United States
Operating environment... Utilities (0 to 40 ° C)
Limits the internal temperature alarm... 0 to 65 ° C
-Other - or ITU (q)
... Internal temperature 38 C
Outdoor temperature... + 20 C
Fan Status....................................... Ok
State of 802. 11 b network... Activated
State of 802. 11A network... Activated
Number of wireless LANs... 14
Number of Active Clients... 71
Built-in MAC address... C8:9 C: D: 8 1: 52:E0
Power supply 1... Currently, OK
Power supply 2... Absent
Maximum number of taken access points supported... 100
Here is the result which leaves on concluded that the AP joins the WLC for a short period and then goes offline
WT-4thFlr-AP3 #.
* 15:42:04.419 Dec 14: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (CAPWAP_WTP_EVENT_REQUEST
., 3)
* 15:42:11.443 Dec 14: EVT-4-AVT %: write flash: / done event.capwap
* 15:42:11.483 Dec 14: LWAPP-3-CLIENTERRORLOG %: switch to standalone mode
* 15:42:11.487 Dec 14: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION
* 15:42:11.487 Dec 14: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 10.250.32.8:5246
* 15:42:11.571 Dec 14: % FEDS-6-persons with DISABILITIES: Signature of IDS is removed and disabled.
* 15:42:21.575 Dec 14: % 3-CAPWAP-ERRORLOG: MWAR selected ' wificontroller'(index 0).
* 15:42:21.575 Dec 14: % 3-CAPWAP-ERRORLOG: go join a capwap controller
* 15:42:12.000 Dec 14: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.250.32.8 peer_port: 5246
* 15:42:14.303 Dec 14: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 10.250.32.8 peer_port: 5246
* 15:42:14.303 Dec 14: % CAPWAP-5-SENDJOIN: send request to join 10.250.32.8
* 15:42:15.127 Dec 14: "Promiscuous" from Ethernet mode
* 15:42:15.535 Dec 14: LWAPP-4-CLIENTEVENTLOG %: OfficeExtend Localssid recorded Flash AP
* 15:42:15.667 Dec 14: ac_first_hop_mac - IP:10.1.2.250 Hop IP:10.1.2.250 IDB:BVI1
* 15:42:15.667 Dec 14: AC setting hop first MAC: 0017.c575.a23c
* 15:42:15.855 Dec 14: % CAPWAP-5-JOINEDCONTROLLER: AP joined controller wificontroller
* 15:42:15.911 Dec 14: LWAPP-4-CLIENTEVENTLOG %: No. Flex ACL to load map configuration file. To connect to the controller to get the configuration file
* 15:42:15.911 Dec 14: LWAPP-4-CLIENTEVENTLOG %: No. Flex ACL to load map configuration file. To connect to the controller to get the configuration file
* 15:42:15.911 Dec 14: LWAPP-4-CLIENTEVENTLOG %: map No. LS Flex to load ACL configuration file. To connect to the controller to get the configuration file
* 15:42:15.915 Dec 14: LWAPP-4-CLIENTEVENTLOG %: no central Dhcp configuration file map to load. To connect to the controller to get the configuration file
* 15:42:15.915 Dec 14: % LWAPP-3-CLIENTERRORLOG: connected mode
* 15:42:23.639 Dec 14: FEDS-6-ACTIVATED %: Signature of IDS is loaded and enabled
* 15:42:34.615 Dec 14: CLEANAIR-6-State: Slot 0 disabled
* 15:42:34.615 Dec 14: CLEANAIR-6-State: Slot 1 disabled
* 15:45:43.783 Dec 14: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (CAPWAP_WTP_EVENT_REQUEST
(. 11).
* 15:45:43.787 Dec 14: LWAPP-3-CLIENTERRORLOG %: switch to standalone mode
* 15:45:43.787 Dec 14: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION
* 15:45:43.787 Dec 14: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 10.250.32.8:5246
* 15:45:43.867 Dec 14: % FEDS-6-persons with DISABILITIES: Signature of IDS is removed and disabled.
* 15:45:53.867 Dec 14: % 3-CAPWAP-ERRORLOG: MWAR selected ' wificontroller'(index 0).
* 15:45:53.867 Dec 14: % 3-CAPWAP-ERRORLOG: go join a capwap controller
* 15:45:44.000 Dec 14: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.250.32.8 peer_port: 5246
* 15:45:46.315 Dec 14: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 10.250.32.8 peer_port: 5246
* 15:45:46.315 Dec 14: % CAPWAP-5-SENDJOIN: send request to join 10.250.32.8
* 15:45:46.487 Dec 14: "Promiscuous" from Ethernet mode
* 15:45:49.903 Dec 14: LWAPP-4-CLIENTEVENTLOG %: OfficeExtend Localssid recorded Flash AP
* 15:45:50.031 Dec 14: ac_first_hop_mac - IP:10.1.2.250 Hop IP:10.1.2.250 IDB:BVI1
* 15:45:50.031 Dec 14: AC setting hop first MAC: 0017.c575.a23c
Here are the results of the client debugging capwap event about to access:
WT-4thFlr-AP3 #debug capwap customer event
Display debugging EVENT customer CAPWAP is on
WT-4thFlr-AP3 #.
* 15:54:58.335 Dec 14: % 3-CAPWAP-EVENTLOG: Echo interval has expired.
* 15:54:58.335 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC
* 15:54:58.335 Dec 14: % 3-CAPWAP-EVENTLOG: echo sent to 10.250.32.8 request
* 15:54:58.343 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0
* 15:54:58.343 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.
* 15:54:58.343 Dec 14: % 3-CAPWAP-EVENTLOG: echo response from 10.250.32.8
* 15:55:08.000 Dec 14: % 3-CAPWAP-EVENTLOG: setting the time at 15:55:08 UTC 14 December 2013
* 15:55:25.579 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC
* 15:55:25.587 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0
* 15:55:25.587 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.
* 15:55:25.587 Dec 14: % CAPWAP-3-Journal of EVENTS: event Wtp 10.250.32.8 response
* 15:55:25.827 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC
* 15:55:25.835 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0
* 15:55:25.835 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.
* 15:55:25.835 Dec 14: % CAPWAP-3-Journal of EVENTS: event Wtp 10.250.32.8 response
* 15:55:55.835 Dec 14: % 3-CAPWAP-EVENTLOG: Echo interval has expired.
* 15:55:55.835 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC
* 15:55:55.835 Dec 14: % 3-CAPWAP-EVENTLOG: echo sent to 10.250.32.8 request
* 15:55:55.843 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0
* 15:55:55.843 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.
* 15:55:55.843 Dec 14: % 3-CAPWAP-EVENTLOG: echo response from 10.250.32.8
* 15:55:56.000 Dec 14: % 3-CAPWAP-EVENTLOG: setting the time at 15:55:56 UTC 14 December 2013
* 15:56:25.735 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC
* 15:56:25.743 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0
* 15:56:25.743 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.
* 15:56:25.743 Dec 14: % CAPWAP-3-Journal of EVENTS: event Wtp 10.250.32.8 response
* 15:56:25.983 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC
* 15:56:25.991 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0
* 15:56:25.991 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.
* 15:56:25.991 Dec 14: % CAPWAP-3-Journal of EVENTS: event Wtp 10.250.32.8 response
* 15:56:55.991 Dec 14: % 3-CAPWAP-EVENTLOG: Echo interval has expired.
* 15:56:55.991 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC
* 15:56:55.991 Dec 14: % 3-CAPWAP-EVENTLOG: echo sent to 10.250.32.8 request
* 15:56:55.999 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0
* 15:56:55.999 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.
* 15:56:55.999 Dec 14: % 3-CAPWAP-EVENTLOG: echo response from 10.250.32.8
* 15:56:56.000 Dec 14: % 3-CAPWAP-EVENTLOG: setting the time at 15:56:56 UTC 14 December 2013
Here are the results of debug capwap client package in detail:
WT-4thFlr-AP3 #.
* 14 Dec 15:59:01.823: < start="" of="" capwap="" packet ="">>
* 15:59:01.823 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246
* 15:59:01.823 Dec 14: Type Msg: CAPWAP_ECHO_REQUEST
* 15:59:01.823 Dec 14: Msg length: 0
* 15:59:01.823 Dec 14: Msg SeqNum: 44
* 14 Dec 15:59:01.823: < end="" of="" capwap="" packet ="">>
* 14 Dec 15:59:01.831: < start="" of="" capwap="" packet ="">>
* 15:59:01.831 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control
* 15:59:01.831 Dec 14: HLEN 2, Radio ID 0, WBID 1
* 15:59:01.831 Dec 14: Type Msg: CAPWAP_ECHO_RESPONSE
* 15:59:01.831 Dec 14: Msg length: 15
* 15:59:01.831 Dec 14: Msg SeqNum: 44
* 15:59:01.831 Dec 14:
* 15:59:01.831 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 11
* 15:59:01.831 Dec 14: the vendor identifier: 0 x 00409600
* 15:59:01.831 Dec 14:
* 15:59:01.831 Dec 14:
IE: UNKNOWN IT IS ABOUT 151
* 15:59:01.831 Dec 14: IE length: 5
* 15:59:01.831 Dec 14: decode the routine unavailable, Hex Dump printing
* 15:59:01.831 Dec 14:
52 80 46 00 AC
* 14 Dec 15:59:01.831: < end="" of="" capwap="" packet ="">>
* 14 Dec 15:59:20.931: < start="" of="" capwap="" packet ="">>
* 15:59:20.931 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control
* 15:59:20.931 Dec 14: HLEN 2, Radio ID 0, WBID 1
* 15:59:20.931 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_REQUEST
* 15:59:20.931 Dec 14: Msg length: 93
* 15:59:20.931 Dec 14: Msg SeqNum: 38
* 15:59:20.931 Dec 14:
* 15:59:20.931 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 89
* 15:59:20.931 Dec 14: the vendor identifier: 0 x 00409600
* 15:59:20.931 Dec 14:
* 15:59:20.931 Dec 14:
IE: RRM_NEIGHBOR_CTRL_PAYLOAD
* 15:59:20.931 Dec 14: IE length: 83
* 15:59:20.931 Dec 14: decode the routine unavailable, Hex Dump printing
* 15:59:20.931 Dec 14:
00 0 HAS FA 20 08 01 00 07 0A 20 08 03 00 01 FA F4
01 00 00 3 B4 2ND 2ND 06 94 51 79 25 C7 B2 B4 E7
22 FD BE F6 04 00 00 00 00 00 00 00 00 50 52 4F
53 2D 57 69 46 69 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 01 06 0B
01 01 01
* 14 Dec 15:59:20.931: < end="" of="" capwap="" packet ="">>
* 14 Dec 15:59:20.931: < start="" of="" capwap="" packet ="">>
* 15:59:20.931 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246
* 15:59:20.931 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_RESPONSE
* 15:59:20.931 Dec 14: Msg length: 8
* 15:59:20.931 Dec 14: Msg SeqNum: 38
* 15:59:20.931 Dec 14:
* 15:59:20.931 Dec 14: Type: CAPWAP_MSGELE_RESULT_CODE, length 4
* 15:59:20.931 Dec 14: result of Code: CAPWAP_SUCCESS
* 14 Dec 15:59:20.931: < end="" of="" capwap="" packet ="">>
* 14 Dec 15:59:21.139: < start="" of="" capwap="" packet ="">>
* 15:59:21.139 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control
* 15:59:21.139 Dec 14: HLEN 2, Radio ID 0, WBID 1
* 15:59:21.139 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_REQUEST
* 15:59:21.139 Dec 14: Msg length: 111
* 15:59:21.139 Dec 14: Msg SeqNum: 39
* 15:59:21.139 Dec 14:
* 15:59:21.139 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 107
* 15:59:21.139 Dec 14: the vendor identifier: 0 x 00409600
* 15:59:21.139 Dec 14:
* 15:59:21.139 Dec 14:
IE: RRM_NEIGHBOR_CTRL_PAYLOAD
* 15:59:21.139 Dec 14: IE length: 101
* 15:59:21.139 Dec 14: decode the routine unavailable, Hex Dump printing
* 15:59:21.143 Dec 14:
01 0 TO FA 20 08 01 F4 00 07 0A 20 08 00 01 0C FA
01 00 00 3 B4 2ND 2ND 06 94 51 79 25 C7 B2 B4 E7
22 FD BE F6 04 00 00 00 00 00 00 00 00 50 52 4F
53 2D 57 69 46 69 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 24 28 2
30 34 38 3 40 95 99 9 01 01 01 01 01 01 01 A1
01 01 01 01 01
* 14 Dec 15:59:21.143: < end="" of="" capwap="" packet ="">>
* 14 Dec 15:59:21.143: < start="" of="" capwap="" packet ="">>
* 15:59:21.143 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246
* 15:59:21.143 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_RESPONSE
* 15:59:21.143 Dec 14: Msg length: 8
* 15:59:21.143 Dec 14: Msg SeqNum: 39
* 15:59:21.143 Dec 14:
* 15:59:21.143 Dec 14: Type: CAPWAP_MSGELE_RESULT_CODE, length 4
* 15:59:21.143 Dec 14: result of Code: CAPWAP_SUCCESS
* 14 Dec 15:59:21.143: < end="" of="" capwap="" packet ="">>
* 14 Dec 15:59:25.547: < start="" of="" capwap="" packet ="">>
* 15:59:25.547 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246
* 15:59:25.547 Dec 14: Type Msg: CAPWAP_WTP_EVENT_REQUEST
* 15:59:25.547 Dec 14: Msg length: 14
* 15:59:25.547 Dec 14: Msg SeqNum: 45
* 15:59:25.547 Dec 14:
* 15:59:25.547 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 10
* 15:59:25.547 Dec 14: the vendor identifier: 0 x 00409600
* 15:59:25.547 Dec 14:
* 15:59:25.547 Dec 14:
IE: RRM_LOAD_DATA_PAYLOAD
* 15:59:25.547 Dec 14: IE length: 4
* 14 Dec 15:59:25.547: slot ccaLoad 0 rxLoad 0 txLoad 0 33
* 14 Dec 15:59:25.547: < end="" of="" capwap="" packet ="">>
* 14 Dec 15:59:25.555: < start="" of="" capwap="" packet ="">>
* 15:59:25.555 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control
* 15:59:25.555 Dec 14: HLEN 2, Radio ID 0, WBID 1
* 15:59:25.555 Dec 14: Type Msg: CAPWAP_WTP_EVENT_RESPONSE
* 15:59:25.555 Dec 14: Msg length: 0
* 15:59:25.555 Dec 14: Msg SeqNum: 45
* 14 Dec 15:59:25.555: < end="" of="" capwap="" packet ="">>
* 14 Dec 15:59:25.795: < start="" of="" capwap="" packet ="">>
* 15:59:25.795 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246
* 15:59:25.795 Dec 14: Type Msg: CAPWAP_WTP_EVENT_REQUEST
* 15:59:25.795 Dec 14: Msg length: 14
* 15:59:25.795 Dec 14: Msg SeqNum: 46
* 15:59:25.795 Dec 14:
* 15:59:25.795 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 10
* 15:59:25.795 Dec 14: the vendor identifier: 0 x 00409600
* 15:59:25.795 Dec 14:
* 15:59:25.795 Dec 14:
IE: RRM_LOAD_DATA_PAYLOAD
* 15:59:25.795 Dec 14: IE length: 4
* 14 Dec 15:59:25.795: slot ccaLoad 1 rxLoad 0 txLoad 0 0
* 14 Dec 15:59:25.795: < end="" of="" capwap="" packet ="">>
* 14 Dec 15:59:25.803: < start="" of="" capwap="" packet ="">>
* 15:59:25.803 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control
* 15:59:25.803 Dec 14: HLEN 2, Radio ID 0, WBID 1
* 15:59:25.803 Dec 14: Type Msg: CAPWAP_WTP_EVENT_RESPONSE
* 15:59:25.803 Dec 14: Msg length: 0
* 15:59:25.803 Dec 14: Msg SeqNum: 46
* 14 Dec 15:59:25.803: < end="" of="" capwap="" packet ="">>
* 14 Dec 15:59:30.375: < start="" of="" capwap="" packet ="">>
* 15:59:30.375 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control
* 15:59:30.375 Dec 14: HLEN 2, Radio ID 0, WBID 1
* 15:59:30.375 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_REQUEST
* 15:59:30.375 Dec 14: Msg length: 17
* 15:59:30.375 Dec 14: Msg SeqNum: 40
* 15:59:30.375 Dec 14:
* 15:59:30.375 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 13
* 15:59:30.375 Dec 14: the vendor identifier: 0 x 00409600
SlotId: 0
Mobile Mac Addr: BC:52:B7:E3:17:CB
* 14 Dec 15:59:30.375: < end="" of="" capwap="" packet ="">>
* 14 Dec 15:59:30.375: < start="" of="" capwap="" packet ="">>
* 15:59:30.375 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246
* 15:59:30.375 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_RESPONSE
* 15:59:30.379 Dec 14: Msg length: 8
* 15:59:30.379 Dec 14: Msg SeqNum: 40
* 15:59:30.379 Dec 14:
* 15:59:30.379 Dec 14: Type: CAPWAP_MSGELE_RESULT_CODE, length 4
* 15:59:30.379 Dec 14: result of Code: CAPWAP_SUCCESS
* 14 Dec 15:59:30.379: < end="" of="" capwap="" packet ="">>
* 14 Dec 15:59:30.387: < start="" of="" capwap="" packet ="">>
* 15:59:30.387 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control
* 15:59:30.387 Dec 14: HLEN 2, Radio ID 0, WBID 1
* 15:59:30.387 Dec 14: Type Msg: CAPWAP_WTP_EVENT_RESPONSE
* 15:59:30.387 Dec 14: Msg length: 0
* 15:59:30.387 Dec 14: Msg SeqNum: 47
* 14 Dec 15:59:30.387: < end="" of="" capwap="" packet ="">>
* 14 Dec 16:00:00.387: < start="" of="" capwap="" packet ="">>
* 16:00:00.387 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246
* 16:00:00.387 Dec 14: Type Msg: CAPWAP_ECHO_REQUEST
* 16:00:00.387 Dec 14: Msg length: 0
* 16:00:00.387 Dec 14: Msg SeqNum: 48
* 14 Dec 16:00:00.387: < end="" of="" capwap="" packet ="">>
* 14 Dec 16:00:00.395: < start="" of="" capwap="" packet ="">>
* 16:00:00.395 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control
* 16:00:00.395 Dec 14: HLEN 2, Radio ID 0, WBID 1
* 16:00:00.395 Dec 14: Type Msg: CAPWAP_ECHO_RESPONSE
* 16:00:00.395 Dec 14: Msg length: 15
* 16:00:00.395 Dec 14: Msg SeqNum: 48
* 16:00:00.395 Dec 14:
* 16:00:00.395 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 11
* 16:00:00.395 Dec 14: the vendor identifier: 0 x 00409600
* 16:00:00.395 Dec 14:
* 16:00:00.395 Dec 14:
IE: UNKNOWN IT IS ABOUT 151
* 16:00:00.395 Dec 14: IE length: 5
* 16:00:00.395 Dec 14: decode the routine unavailable, Hex Dump printing
* 16:00:00.395 Dec 14:
52 80 81 00 AC
* 14 Dec 16:00:00.395: < end="" of="" capwap="" packet ="">>
Try reducing the mtu on ap 2600.
-
Stand-alone configuration of Cisco Aironet 700i
Hello
I'm well aware new products Cisco. So please forgive my basic questions.
I have Cisco Aironet 700 series AP(AIR-SAP702I-Q-K9). I don't have a controller. I need to set this up as standalone access point.
I tried all the basic steps and tried to activate the two radios, but no luck. Anyone can guide me please on how to configure the AP.
I use web access to configure the AP.
Help, please
Thank you
Sagar
Hi Sam,
Please check these messages to set up autonomous AP.
https://rscciew.WordPress.com/2014/05/24/single-SSID-configuration-on-au...
https://rscciew.WordPress.com/2014/05/24/multiple-SSID-configurations-on...
Concerning
Remember messages useful rates
-
Configuration Cisco AP 2600 (AIR-CAP2602I-E-K9) and Cisco 2500 wireless controller?
This is the first time that I work with this type of devices (Cisco Ap 2600 (AIR-CAP2602I-E-K9) and wlc 2500)... my experience to the CCNP (router and Switch)
How configuration Cisco Ap 2600 (AIR-CAP2602I-E-K9) and wlc 2500?
Please find attachment (Cisco device map)
Hello
Here are the docs for you to configure the Basic for AP switch port configuration IE 2600 s and wlc.
WLC port must be configured as a trunk.
Port of the AP must be access.
CAP2600 series requires software 7.2.110.0 wlc minimum (make sure you have it or above release)
Upgrade if you follow it.
http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_example09186a00805f381f.shtml
1. http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a0080665cdf.shtml (SW port configs)
2. http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806c9e51.shtml
(Another thing very importand, discovery mechanism, choose properly)
If you choose the option dhcp 43, it uses the TLV format. Type is always f1, the length is 4 * (wlc number for which you want to provide discovery for, in your case) Value = Hex conversion of the wlc management ip address.
A video for the process of
http://www.youtube.com/watch?v=oOh_Iv1CHxQ.
Thank you
Sahil
-
Only the needs of the Cisco Aironet 1550 series a WLC?
Hello
Nice day. I would like to ask if the Cisco Aironet 1550 series requires a controller to run. Note that the references SKU in this fomat AIR-CAP1552E-A-K9-AIR-CAP1552EU-A-K9. I noticed that on the autonomous access point there they keyword 'SAP' on its SKU while the controller based has "CAP". If the
Cisco Aironet 1550 Series needs a controller which controller should it be associated? (e.g. AIR-CT2500)
Thank you
It can work stand-alone image:
1550 relies on:
2500, 7500, 5508, WISM2,... .etc
check the release notes of the code controller that you have and you should be able to identify what is supported and what is not supported.
----------------------------------------------------------------------------------------------
Please ensure good answers to rate
-
I have a (AIR-LAP1131AG-A-K9), I can set it up as a stand-alone?
I have a lightweight access point (AIR-LAP1131AG-A-K9). I would like to use it as a stand-alone gateway (AIR-AP1131AG-A-K9). Is this possible? There are configuration changes that need to happen to make this happen? Do I need to use different operating system?
Thank you
Siva
Plug the AP directly on your PC not the router.
The best way to proceed is to comfort in the AP and make sure that the
AP can reach the laptop via a switch or a crossover cable
fixing directly from the laptop and the AP.
With your cable from the console, you will be able to see if you pressed on the
button for 20 seconds.
By using a TFTP server to revert to a previous version
Follow these steps to return standalone by LWAPP mode
Download a version of Cisco IOS using a TFTP server:
Step 1 in the IP address of the computer on which your TFTP server
software should be from 10.0.0.2 to 10.0.0.30.
Step 2 make sure that the PC contains the image point (for example file
as c1200-k9w7 - tar.122 - 15.JA.tar for series 1200 point access) in the
The TFTP server folder and the TFTP server is activated. Monitor of the
TFTP program to see the code for transfer to the AP.
Step 3 Rename the access point image file in the TFTP server folder
C1200-k9w7 - tar.default for series 1200 point access,
C1130-k9w7 - tar.default for a series of 1130 access point, and
C1240-k9w7 - tar.default for 1240 series access point.
Step 4 connect the PC AP with a category 5 (CAT5)
Ethernet cable. This must be a crossover cable if connected
to the AP. Or ethernet cable is normal if the AP and laptop are connected
to a switch.
Step 5 disconnect the power to the access point.
Step 6 push the MODE button and hold the button while you reconnect power to the access
point.
Step 7 press and hold the MODE button until the status light turns red
(about 20-30 seconds), then release.
Step 8 wait that access point restarts, as attested by all lights
Green followed the status light blinks green.
Step 9 after the access point reboots, reconfigure using the graphical interface or
the CLI.
If the image is not download from Server/tftp on your computer, you may need to delete the previous image of tar on the access point of the console:
Simply hold the mode button until the light is red.
Then, by using the console port, make sure that the guest is AP: and do a show «»
"Flash:" on the device and make sure that there is no image that begins
"c1130-rcvk9w8-tar..." ». If there is an image that starts with who then
Delete it with "delete flash:
-
2600 series all-in-one: print white paper
When I try to print from the computer or the flat bed, the paper that comes out is empty and no error message! How can I solve this problem?
Hi @frontollie,
I'd love to help you with your printer 2600 series. If it's a printer Photosmart 2600, I suggest to use the following document to solve the problem: HP Photosmart 2610 and 2710 series all-in-one - solving problems of quality printing with the diagnosis Page. According to your description, I understand the printer produces white pages, and I follow the steps presented in the document above can help.
Please let me know if this helps you to find a solution, or if you need help. In fact, if this resolves the issue, please click Accept as Solution to identify your request as resolved. Thank you.
-
How to analyze the files using Lexmark 2600 Series
To the right:
I have a Lexmark 2600 Series 3-in-1 printer. It is supposed to be able to scan. However, I can't figure out how to parse the files and I've lost the installation disc. However, the printer is already installed on my computer. I can't analyze. Can someone help me on how to scan files with this printer? Or, is there something I need to do first before that I can use the scanner fuction?
Hi Xnygga,
You will need to go to the Lexmark Web site to download the latest software/drivers for your scanner:
http://support.Lexmark.com/index?page=home&locale=en&UserLocale=en_US & segment = DOWNLOAD
I hope this helps!
Debra
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think -
Quality of the Air on AIR-CAP2602I
Hi all
just a quick, AIR-CAP2602I supports the full-fledged clean characteristic air?
any good links/blog out there on how to enable it and its air pure vs comparison explicit?
How to activate this
Wireless > 802. 11a / g > CleanAir > under CleanAir settings, check "enabled."
his air pure vs express comparison
CleanAir Express is only access point "1 K" models, i. e. 1600, 1700, 1800. The difference between CleanAir and CleanAir Express is a dedicated "chip" for the 2Ks & 3Ks CleanAir. CleanAir Express does not have this chip for all CleanAir function is made by the CPU of the APs.
-
Hello
I have a cisco aironet 1100 Series wireless access point.
by mistake I delete the IOS of the router and now I need to copy the IOS image again on it.
I need your help please.
For now, he has the Ethernet led RED, Green State, Rdio RED. T no Cisco IOS image file the spirits).
I downloaded the file c100-k9w7 - mx.123 - 8.jed
and I download the tftp (tftpd32) servers
I have the router connected directly to a pc with the static ip address of 10.0.0.2
but the problem is actually that I don't need the 1100 router ip address right now, I can't access it through a web browser.
and by a tftpd32 I try but no function.
I don't know what I'm doing wrong.
other things, it's that I did not find a clear manual on how to use a tftpd32 to transfer the file to the cisco router 1100 series.
Thank you.
I'll wait your hepls.
Convert a standalone Lightweight Access Point
http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html#wp161272 -
How to move a stand-alone series C of Cisco UCS managed service profile without losing any data?
Hello
We currently have a stand-alone series cisco C with 2012 Windows Server installed on the local disks. We need to go this Cisco UCS server managed with a service profile, but can not lose existing data and the method of operating system boot.
Does anyone know how to do this?
Thank you
Hi Adrien,.
To be able to accomplish this together the local drive to 'any Configuration' policy this way UCSM won't overwrite the current raid on the server configuration.
See the link below
http://www.Cisco.com/c/en/us/TD/docs/unified_computing/UCS/SW/GUI/config...
Let me know if that helps
-
Hello, I am looking for the AIR-CAP2602E BTU value. I can't find it in the sheet.
The amount of heat generated is a function of the amount of energy used. The 2602 uses up to 12.95W which translated to 44.2 BTU. If you clear one or both, radios, I would expect this number considerably.
John
-
Conversion of Cisco Aironet 1130AG light in stand-alone mode
Hello
I just bought AIR-LAP1131AG. Unfortunately, I want stand-alone and not lightweight fashion.
Yes, is there a procedure to convert to "AIR-AP1131AG?
Thank you.
Hello Michael,
Yes, please follow this procedure for TFTP Re-imaging
/ * Style definitions * / table. MsoNormalTable {mso-style-name: "Table Normal" "; mso-knew-rowband-size: 0; mso-knew-colband-size: 0; mso-style - noshow:yes; mso-style-priority: 99; mso-style-parent:" ";" mso-padding-alt: 0 to 5.4pt 0 to 5.4pt; mso-para-margin: 0; mso-para-margin-bottom: .0001pt; mso-pagination: widow-orphan; do-size: 10.0pt; do-family: "Times New Roman", "serif" ;} "}
1) Go to your Computer and from the tool menu -> folder options ->uncheck the hide extensions for known file types option.
2) Download the IOS image ( you can get this ios image from cisco.com) on your desktop.
3) Rename the image into c1130-k9w7-tar.default
4) Give your computer Ethernet an address in the range 10.0.0.2 till
10.0.0.30
5) Run the tftp server on your computer.
- Make sure that the directory of your tftp server is the desktop.
- Specify the AP address on the tftp server if needed.
6) Connect the AP to the computer with Ethernet cable.
7) Remove the power from the AP.
8) Press and hold Mode button on the AP, and insert the power jacket in the AP.
9) Keep pressing on the Mode button for (20-30 seconds) until you see RED Led.
10) Wait until the image installed and all led lights return to green
doesn't make sure that no firewall or antivrus is running on your computer.
I hope this helps.
Kind regards
Talal
=============
Please note the answers that will help you
Maybe you are looking for
-
The material is IMac mid 2010 release with the latest updates. A 4 GB memory. A great deal on Leopard, fails only with lion. The key is to limit open windows or tabs which is unacceptable for the use of the browser.
-
Dolby home theater v4 is not working in lenovo ideapad Z580
Initially, my laptop had windows 7, recently I've updated to 8.1 windows When I installed realtek audio driver, digital cinema more House of dolby has been installed instead of dolby home theater v4. Can aynone give please get detailed steps for inst
-
Exchange of data between the internal and external labview code
Sorry for a simple question. I have a TestStand sequence that uses units/tests written in LabVIEW. The sequence is extermnally began with a stand alone LabVIEW program. I need to establish simple exchanges of information between units of the sequence
-
I can access Windows Live from my macbook, but when I try to go in my hotmail Inbox I get a sorry, there is a problem with hotmail right now. I CAN access my hotmail to my IMac account. What is happening that I can't access my account hotmail to my
-
800f080d error installation KB968930
tried to install the update KB968930 and got error 800f080d