Aironet 3500i

Similar Questions

• Aironet 2802i Radio0 has not started, not enough power POE on SG300-28PP switch

  When I restart Aironet 2802i which is powered by 28PP SG300 28 - Port Gigabit PoE + switch, I saw the following message:

  [* 13:47:31.8044 26/09/2016] Radio0 has not started, not enough power POE
  [* 13:47:31.8173 26/09/2016] DOT11_DRV [0]: set_channel channel set to 11
  [* 13:47:33.0109 26/09/2016] DOT11_DRV [1]: set_channel channel set to 36
  [* 13:47:33.6506 26/09/2016] Radio1 not started, not enough power POE

  Series Aironet 2800 get started guide mentions "any 802.3at (25.5 W) compatible switch port" and SG300-28PP seems to be consistent.

  Please advise, thank you.

  Dennis

  Oh sorry, I got a 2602 in my head, but you use the built-in WLC? I have not had the chance to play with those, but assumes that it will be the same.

  Try to display the summary ap and ap 802. 11A of summary config

  See you soon,.

  Ric

• Cisco Aironet SAP1602E - changing open to WPA - PSK access remote (RAP and map)

  I currently have a deployment of Cisco Aironet SAP1602E Wireless point to point bridge (bridge using RAP and card, root wireless and Non-Root Bridge) to expand a layer 2 VLAN from one building to the other. It currently operates uisng open authentication and encryption - and is administered remotely via the bridge of root, to get wireless (manage) the bridge Non-Root - RAP wireless remote.

  Try to configure the PSK WPA2-PSK remotely via the GUI or CLI - first setup - I informed a similar error to her below indicating that:

  Error: Key-management WPA is requried for WPA-PSK

  Read around, it seems, there is a configuration-control problem, and that I need to specify the mode as WPA2-PSK first, before then being able to specify the PSK there instead of using. However, as soon as this mode is specified on RAP, my remote administration is broken - as probably the RAP try to use WPA2-PSK to look for a PSK, which has not yet been configured. Am I missing something obvious here, or is the order of operations of CLI (1] convert to WPA - PSK; (2] shared secret to apply PSK) as a migration from open to WPA2-PSK cannot be configured remotely (short of preparation of a startup-config; TFTPing presents more; and issuance of a 'reload' remote control)? Can someone please enlighten me as to what the logic is here - no doubt I should be able to specify a PSK first (fo without worrying if I use WPA, WPA2 or other), and then be able to specify that I want as the layer of encryption (WPA) to make use of this pre-parameter PSK? If it was a router, you don't can me to add something to the authentication key chain OSPF; before clarifying its use - why so different Aironet Wireless IOS?

  You're right, and because you will have to enter several lines of configuration to switch to WPA2-PSK with AES didn't really matter; the AP would reset the radio anyway because you make changes related to the radio interface. It would be very useful that if Cisco router/switch IOS 'macro' feature available AP thus in changes like this, unfortunately this is not the case.

  Start with the nonroot AP and make sure that the following lines are added to your configuration. If you add by the console, the order must be like that, do it by downloading a new configuration of booting with tftp, that it does not matter.

  interface Dot11Radio0
  encryption ciphers aes - ccm mode

  SSID dot11 TEST
  authentication wpa key management
  WPA - psk ascii 0

  Please rate helpful messages... :-)

• Defining a 1852nd Aironet AP - Radio Off - Cisco IOS 12.3 (4) JA

  I have a brand new Cisco Aironet 1800 AP series I'm trying to install. Specifically the 1852E. I do not have a controller and try to use the method of deployment of mobility Express. When I received the unit there is a yellow label more precisely declaring outside: "OFF BY DEFAULT note RADIOS: radios are disabled by default for Cisco IOS releases 12.3 (4) JA and later.

  If anyone can please tell me how I am supposed to this access point configuration when the radios are not suite, so the CiscoAirProvision SSID is not broadcast?

  I tried the following:

  1 connect the unit to my PoE switch. Unit Gets power and discovery mode starts (red/orange/green light cycling). He succeeded receives an IP address from my DHCP.

  2. when I try to access the device through my laptop via the local LAN it just times out. Pings meet.

  I apologize if my post seems harsh, I am quite agitated that even after having spent more than 5 hours trying to troubleshoot and get this thing to work, there was nothing else than a nightmare (both for the installation of touted 10 min). I do RTFM. I missed something simple jumps? or am I just to assume that Cisco has really missed the boat the patch appropriate for an assignment in their literature.

  FOR INFO. Thorough searches Google and research on this forum gave me no help.

  Thank you.

  Convert a CAWAP AP an AP express mobility

• Could turn off the light of State Aironet 1130?

  We had an Aironet must installed on darkroom but its status LED continues to blink. We could turn off the LED set up? As I knew that this access point can be set continuously flashing the LED State.

  There is no way I know to turn off the leds. The only hidden command is one that allows their flashing of the cli and change the duration of each, but it won't stop them. Insulating on the leds tape is probably your only option.

• Point of access Cisco Aironet 1200 series help

  We have 4 Cisco Aironet 1200 Access Points and they are all set to authenticate with our RADIUS server. However, authentication is hooked and can't understand why. Does anyone have any knowledge/experience with Cisco Aironet 1200 Access Points configuration?

  OK, I do not work with the GUI so although the memory is a little hazy but from the APs home page look on the left hand side and there is an option for something like "Software Setup" or something to that effect. You should be able to find the IOS version of here. This requires that you are indeed runnig IOS code. How old are these APs? If more than a few years ago (and perhaps even more recent) that they could very well be running VxWorks and then we are in a different ball game. If you see what I have described above and the homepage for the AP is often white with a bit of greenish-blue, bluish-green color then IOS, if it is more colorful, yellow stuff and VxWOrks.

  I hope this helps. Let me know if you need anything that anyone else. I will try to answer as soon as POSSIBLE.

• Linux + pci aironet 350 + PEAP?

  Hello

  We have a number of embeded linux devices with PCI aironet 350 cards

  However our campus network can't jump (because of security concerns)

  the version of the driver which is the devs embeded running ar

  Linux-acu-pilot - v2.1

  no idea how I can get something more recent that supports PEAP?

  Try using xsupplicant.

  http://Open1x.sourceforge.NET/

• Aironet 1200 and MAC authentication

  Hi all

  I Aironet 1210 and you want to implement the authentication MAC without ACS.

  Now, I know that any AP Aironet can allow authentication MAC se store the list of MAC addresses.

  So after the command:

  TestAP (config-if-ssid) #authentication open mac

  TestAP (config-if-ssid) #authentication open mac address?

  WORD mac address list (1-31 characters) name

  There is no way I can list all MAC addresses in the list. I use IOS Version 12.2 (13) JA3.

  Any help would be greatly appreciated.

  Kind regards

  Samuel Wilson

  If you do not have a RADIUS server on your network, you can create a list of MAC addresses allowed on advanced security of access point: MAC address authentication page. Devices with not on the list of MAC addresses are not allowed to authenticate.

  I use the GUI to make a list:

  http://www.Cisco.com/en/us/products/HW/wireless/ps4570/products_configuration_example09186a00801c0912.shtml

  The link above is to use the local capacity of GANYMEDE to the AP, but if you select the option "Advanced Security" on the right side of the web interface, it will take you to the page where you can create your list of mac addresses.

  Please evaluate the useful messages.

• Updated standalone Cisco Aironet lightweight mode Access Points

  I'm trying to convert a stand-alone Aironet 1200 in light Mode. I use the tool to upgrade v1.0 proposed by Cisco. But when I put the name of the recovery LWAPP Image (c1200-k9w7 - tar.123 - 7.JA2) in the tool window to update it doesn't work. It is said: c1200-k9w7 - tar.123 - 7.JA2 - LWAPP recovery Image file size is zero. But its size is 4.6 MB!

  Can someone help me?

  Convert the Aironet 1200 of autonomous light mode follow the procedure set out in document http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp23144.

• Cisco Aironet 1830 disable broadcasting of the SSID

  I recently bought a Cisco Aironet 1830 with the mobility Express version. installed 8.2.100.0. This unit is my controller and my only AP. I configured the device, but I can't seem to find a setting in the GUI or the CLI of the controller or AP disable broadcasting of the SSID. Can someone help with this?

  Thank you

  The CLI is available, the following command:

  config ssid broadcast disable wlan where wlan id is the number of your wlan. If in doubt, do a show wlan summary which should give you this info, I hope.

  Ric

• Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  I have (2) AIR-SAP2602I-A-K9, configured the same way.

  on two different remote LANs.

  They don't seem to be handing out addresses via DHCP.

  {If I connect to a local network with another DHCP server}

  wireless devices can obtain addresses

  This another DHCP server on the LAN through the access point.}

  I followed 12.4.25d. JA.cg.pdf

  Configuration of the Access Point to provide the Service DHCP 5-22

  ---------|---------|---------|

  e.g. 3444-RCS1-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS1-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.29.89

  IP dhcp RCS1 pool

  network 192.168.29.88 255.255.255.248

  router by default - 192.168.28.1

  Rental 1 0

  interface BVI1

  IP 192.168.28.211 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.28.1

  ---------|---------|---------|

  ---------|---------|---------|

  e.g. 3444-RCS2-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS2-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.129.81

  IP dhcp RCS2 pool

  network 192.168.129.80 255.255.255.248

  router by default - 192.168.128.1

  Rental 2 0

  interface BVI1

  IP 192.168.128.171 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.128.1

  ---------|---------|---------|

  Thats the DHCP Pool range 192.168.29.88 through 192.168.28.95

  Well this will confuse your customers.

  And this is NOT how to set up your "range".   See below:

  DHCP excluded-address IP 192.168.29.1 192.168.29.87

  DHCP excluded-address IP 192.168.29.96 192.168.29.254

  IP dhcp RCS1 pool

  network 192.168.28.211 255.255.254.0

  router by default - 192.168.28.1

  Rental 1 0

• Aironet AP Cisco mode

  Hi all

  Please, how can I check my aironet 702i AP (light or stand-alone) mode because I need to join the vWLC and found only slight AP can be attached to WLC?

  Thank you in advance

  K9W7

  OK, "W7" means independent IOS.

• How to set up a standalone Aironet AP? 1260 series

  I am new to the Cisco Aironet access point. I got a new AUTONOMOUS Aironet 1260 series access point device. Part # AIR - AP1262N - A - K9. The package came with any guide, CD, and AC adapter. I searched Cisco sites, but found no suitable textbooks. I found a getting started guide, but not for standalone AP, this is for on controller AP. Question - where can I find manuals / guides to install and set up my own new Cisco Aironet Access Point 1260? Frankly speaking, Cisco sites are NOT respectful of these new Cisco users!

  Thank you!

  go to the link below... itsthe config u example and gives a lot of info...

  http://www.Cisco.com/en/us/docs/wireless/access_point/12.4_21a_JA1/configuration/guide/scg12421aJA1-Chap1-overview.html

  If you want to configure your access point for WPA2 PSK authentication then here is the link...

  http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_example09186a008054339e.shtml

  Let me know if this helps and please remember to note the useful messages!

  Concerning

  Surendra

• WAP321 & 2602e Aironet wireless 2504 controller?

  Hello

  I am new to Cisco network. I am currently in an environment with no controller wireless and wifi uses two WAP321 Cisco.  The company wants to expand the wireless and bought a Cisco 2504 wireless controller and a controller of Cisco Aironet 2602e WAP.  My question is when we will start using the controller can he control the WAP321 formerly controller - less or will be replaced by a different Cisco Aironet 2602e?  Thank you.

  My question is once we start using the controller can it control the formerly controller-less WAP321's
  

  WLC 2504 will not support AP321s.  Talk to your dealer of Cisco and see if they accept if you want to trade the AP321 for the AP 2602.

  Make sure that your AP 2602 have the appropriate regulatory domain.  If you are not sure, DO NOT open the boxes.

  For more information, go here:

  http://www.Cisco.com/en/us/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd80537b6a_ps10981_Products_Data_Sheet.html

  Another thing, for AP 2600, your 2504 should have the minimum firmware of 7.2.110.X.  IF you do not, then talk to the Cisco authorized dealer who sold you the controller and kindly ask (nicely) if they can download the firmware for you.

• Aironet 1240AG - cannot use the web interface

  I'm trying to set up a new Aironet 1240AG. After that she won an IP from the DHCP in my LAN, I can always connect using the web interface. I use an Internet Explorer 6.0 on Win 2000. It keeps telling me cannot find the server. Please I need help

  Hi Olivier,.

  First off you're welcome :) This method really works without the need for a WLC, be patient. Check the address static IP put you on your TFTP (* range 10.0.0.2 to 10.0.0.30)

  Rename the access point image file in the folder of the server TFTP c1200-k9w7 - tar.default for a series of 1200 access point

  Looks like a problem TFTP (no firewall on your PC?)

  Take a look at the details in the following threads that each has to do with TFTP. There are some great tips to troubleshoot TFTP some of my NetPros favorite ScottMac, Cisco's Stephen and Jack Young. The likely culprit may be you need to uncheck "Hide extensions for known file types" on your server TFTP;

  http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=WLAN%20Radio%20Standards&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddc042b/8#selected_message

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=Wireless%20-%20Mobility&topic=General&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddc03c4/2#selected_message

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=Wireless%20-%20Mobility&topic=General&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddbf271

  I hope this helps! Good luck!

  Rob

  Remember messages useful rate...