Cisco Aironet 1830 disable broadcasting of the SSID

Similar Questions

• Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  I have (2) AIR-SAP2602I-A-K9, configured the same way.

  on two different remote LANs.

  They don't seem to be handing out addresses via DHCP.

  {If I connect to a local network with another DHCP server}

  wireless devices can obtain addresses

  This another DHCP server on the LAN through the access point.}

  I followed 12.4.25d. JA.cg.pdf

  Configuration of the Access Point to provide the Service DHCP 5-22

  ---------|---------|---------|

  e.g. 3444-RCS1-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS1-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.29.89

  IP dhcp RCS1 pool

  network 192.168.29.88 255.255.255.248

  router by default - 192.168.28.1

  Rental 1 0

  interface BVI1

  IP 192.168.28.211 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.28.1

  ---------|---------|---------|

  ---------|---------|---------|

  e.g. 3444-RCS2-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS2-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.129.81

  IP dhcp RCS2 pool

  network 192.168.129.80 255.255.255.248

  router by default - 192.168.128.1

  Rental 2 0

  interface BVI1

  IP 192.168.128.171 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.128.1

  ---------|---------|---------|

  Thats the DHCP Pool range 192.168.29.88 through 192.168.28.95

  Well this will confuse your customers.

  And this is NOT how to set up your "range".   See below:

  DHCP excluded-address IP 192.168.29.1 192.168.29.87

  DHCP excluded-address IP 192.168.29.96 192.168.29.254

  IP dhcp RCS1 pool

  network 192.168.28.211 255.255.254.0

  router by default - 192.168.28.1

  Rental 1 0

• Hide the SSID 1832i

  Hello, I have the Cisco Aironet 1832i (series 1830) model.

  I would like to know how many non-broadcast of the SSID of the wlan 2 I created (the main and the SSID quest)

  Please let me know the commands I have to configure SSH, as the Cisco operating system is different from the other type of Aironets.

  Hello

  Must be identical to that if you can access it via the CLI (Telnet/SSH):

  https://supportforums.Cisco.com/discussion/12947811/Cisco-Aironet-1830-disable-SSID-broadcast

  The CLI is available, the following command:

  config ssid broadcast disable wlan where wlan id is the number of your wlan. If in doubt, do a show wlan summary which should give you this info, I hope.

• Help: wet610n will not connect to wrt610n when the ssid broadcast is disabled

  I have a wet610n wirteless bridge linking very well with my router wrt610n broadcast ssid is enabled on the router, but when I turn it off then (the rest unchanged), the wet610n can not connect.

  What I am doing wrong?

  Or require the wet610n ssid will be broadcast (I didn't read that anywhere)?

  Thank you

  I have power cycled it, but I tried again and then experienced little more after you reset the wet610n and reconfiguring again.

  What seems to work, is to allow the broadcast of the SSID of the router and leaving the wet610n bridge wireless connection. So I can turn off the broadcast of the SSID and power cycle the wet610n and it can then connect.

  Without the first activation of SSID and connected, the bridge connects wireless.

  Thank you - it is "resolved".

• New Cisco Aironet 1602i is not broadcasting the SSID I place

  New Cisco Aironet 1602i is not broadcasting the SSID I place

  SSID I set up is not broadcasting, so I don't see the wireless network to choose and connect. On my laptop if I choose specify the name of the SSID then I am able to connect to the wireless network. I have only 1 Configuration SSID on the access point. Anyone know how to update the configuration for the SSID is broadcast?

  The green light on the AP flashes and turns off about 3 seconds; is this normal or should it stays on all the time?

  Current configuration: 1842 bytes

  !

  version 15.2

  no service button

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  encryption password service

  !

  host ap name

  !

  !

  Pulse 9 logging console

  enable secret 5 $1$ rrlE$ msWqu8CGY/tpDkgRAAAIe /.

  !

  No aaa new-model

  no ip Routing

  no ip cef

  !

  !

  !

  dot11 syslog

  !

  dot11 ssid Mi Casa

  open authentication

  authentication-key wpa version2 management

  WPA - psk ascii 7 142017070F0C787B7579

  !

  !

  Crypto pki token removal timeout default 0

  !

  !

  username Cisco privilege 15 password 7 112A1016141D

  !

  !

  Bridge IRB

  !

  !

  !

  interface Dot11Radio0

  no ip address

  no ip route cache

  !

  encryption algorithms aes - ccm tkip encryption mode

  !

  SSID Mi Casa

  !

  gain of antenna 0

  STBC

  beamform ofdm

  root of station-role

  Bridge-Group 1

  Bridge-group subscriber-loop-control 1

  Bridge-Group 1 covering-disabled people

  Bridge-Group 1 block-unknown-source

  No source of bridge-Group 1-learning

  unicast bridge-Group 1-floods

  !

  interface Dot11Radio1

  no ip address

  no ip route cache

  !

  encryption algorithms aes - ccm tkip encryption mode

  !

  SSID Mi Casa

  !

  gain of antenna 0

  DFS block 3 Strip

  STBC

  beamform ofdm

  channel SFR

  root of station-role

  Bridge-Group 1

  Bridge-group subscriber-loop-control 1

  Bridge-Group 1 covering-disabled people

  Bridge-Group 1 block-unknown-source

  No source of bridge-Group 1-learning

  unicast bridge-Group 1-floods

  !

  interface GigabitEthernet0

  no ip address

  no ip route cache

  automatic duplex

  automatic speed

  Bridge-Group 1

  Bridge-Group 1 covering-disabled people

  No source of bridge-Group 1-learning

  !

  interface BVI1

  IP 192.168.10.200 255.255.255.0

  no ip route cache

  !

  by default-gateway IP 192.168.10.1

  IP forward-Protocol ND

  IP http server

  no ip http secure server

  IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

  !

  1 channel ip bridge

  !

  !

  !

  Line con 0

  line vty 0 4

  local connection

  transport of entry all

  !

  end

  Hi you must guest mode config on the ssid... Read this bud

  https://supportforums.Cisco.com/docs/doc-5442

  Sent by Cisco Support technique iPhone App

• Aironet 1142 not broadcasting the SSID

  I configured the device manually, not even using quick or Express security configuration then... it's possible that I missed something.

  Anyway, here's the problem. Although the SSID is configured as 'AP1', this SSID is not among the networks available on the client computer.

  The connection configured in the group policy for the customer, should happen actually automatically, based on the SSID, but because the SSID is not broadcast, connection fails as well.

  The Aironet is among the available networks 'Other network' and if I click on "connect" I am asked to enter the SSID-> AP1

  Although fashionable, the error message displays (unable to connect to the network, or something to that effect), the laptop * fact * connect once I have close this window. Access to the network is complete and functional - I can ping other hosts, etc...

  I would post screenshots, but not knowing what parameter is missing or incorrect, I must print dozens. So here's the sh run out of the AP obtained via telnet (just below). Can someone tell me what is missing? It's a test network so all information is 'real' (nothing has changed for privacy):

  Note: I even changed the hostname to "AP1" (it's still LAB1 below) but that has not solved the problem (do not think it would be).

  #######################################################################################################

  Lab1 #sh run
  Building configuration...

  Current configuration: 2321 bytes
  !
  version 12.4
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  encryption password service
  !
  hostname LAB1
  !
  Pulse 9 logging console
  enable secret 5 $1$ $9EWD kxrbg8KxikRFypOieKiZh.
  !
  AAA new-model
  !
  !
  AAA rad_eap radius server group
  Server 10.0.0.12 ACCT-port auth-port 1812 1813
  !
  AAA rad_mac radius server group
  !
  AAA rad_acct radius server group
  !
  AAA rad_admin radius server group
  !
  AAA server Ganymede group + tac_admin
  !
  AAA rad_pmip radius server group
  !
  RADIUS server AAA dummy group
  !
  AAA authentication login eap_methods group rad_eap
  AAA authentication login mac_methods local
  AAA authorization exec default local
  AAA accounting network acct_methods power group rad_acct
  !
  AAA - the id of the joint session
  !
  !
  dot11 syslog
  !
  dot11 ssid AP1
  authentication open eap eap_methods
  authentication-key wpa version2 management
  !
  !
  !
  062506324F41 Cisco 7 password username
  !
  !
  Bridge IRB
  !
  !
  interface Dot11Radio0
  no ip address
  no ip route cache
  !
  encryption ciphers aes - ccm mode
  !
  SSID AP1
  !
  gain of antenna 0
  local power 2
  power customer 2
  root of station-role
  Bridge-Group 1
  Bridge-group subscriber-loop-control 1
  Bridge-Group 1 block-unknown-source
  No source of bridge-Group 1-learning
  unicast bridge-Group 1-floods
  Bridge-Group 1 covering-disabled people
  !
  interface Dot11Radio1
  no ip address
  no ip route cache
  Shutdown
  gain of antenna 0
  DFS block 3 Strip
  channel SFR
  root of station-role
  Bridge-Group 1
  Bridge-group subscriber-loop-control 1
  Bridge-Group 1 block-unknown-source
  No source of bridge-Group 1-learning
  unicast bridge-Group 1-floods
  Bridge-Group 1 covering-disabled people
  !
  interface GigabitEthernet0
  no ip address
  no ip route cache
  automatic duplex
  automatic speed
  No keepalive
  Bridge-Group 1
  No source of bridge-Group 1-learning
  Bridge-Group 1 covering-disabled people
  !
  interface BVI1
  IP 10.0.0.51 255.0.0.0
  no ip route cache
  !
  default IP gateway - 10.0.0.12
  IP http server
  no ip http secure server
  IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
  radius of the IP source-interface BVI1
  format of server RADIUS attribute 32 include-in-access-req hour
  RADIUS-server host 10.0.0.12 auth-port 1812 acct-port 1813 borders 7 15135A0E07782F2
  12E60
  RADIUS vsa server send accounting
  1 channel ip bridge
  !
  !
  !
  Line con 0
  line vty 0 4
  !
  end

  LAB1. #

  You must add the command "guest mode" under the terms of the section. (without the quotes of course)

  Sent by Cisco Support technique Android app

• Disable the SSID broadcast

  I have a v1 WRT610N router and cannot find where I'm able to disable the SSID broadcast.  I thought I had looked at all the settings screens, but I can't.   can someone tell me how to disable the SSID broadcast for this router?  Thank you!

  Click on wireless on top and it should show these two things

  (On the red circles)

  

• Disable broadcast SSID and MAC address turn on filtering on WAG320N

  When disabling SSID broadcast and enabling MAC address filtering on WAG320N, my other laptop wireless disconnected.  And when you try to connect, it connects again.

  You can not hide from intruders.

  The router always sends the tag. The router is immediately detected.

  The SSID is always transferred not encrypted. He is always sent over the association. It is easy to force a re-Association. If there is a single device without wire connected to the access point it takes about a second to learn the SSID.

  Disable the SSID requires your wireless devices to search actively for the network. This means that your laptop will always try to connect to your SSID, as long as it is not connected to another network. As sending requires much more power then listen passively it drains your battery.

  And, in fact, if you are in an internet café anyone can learn your SSID in time where you go on the wireless at the moment where you associate with the network of internet café.

  In addition, it causes many problems with different wireless, as instability or similar cards.

  MAC filtering is still more useless that the MAC address is always part of any wireless transmission and it's always clear. It is extremely easy to pick up the allowed MAC addresses, and it is extremely easy to change the MAC address of a wireless card.

  New: use the real security and forget this nickname of security features.

  What you try to do is a waste of time. Of your time. It will slow down any intruder.

  See also

  http://homecommunity.Cisco.com/T5/wireless-routers/iPad-Wi-Fi-MAC-address-quot-not-a-MAC-address-quo...
  http://homecommunity.Cisco.com/T5/wireless-routers/is-my-router-effectively-secured/m-p/333945#M1752...

• The SSID on Cisco WLC support no.

  Hi all

  Can you please help me to provide details on the following Cisco wireless controller?

  1. no support SSID on Cisco WLC

  2. is it possible to limit the SSID on the access point (for example, I have 10 SSID configured on the controller, I want 10 first access points using SSID (SSID 1-5) and rest of the AP SSID 6-10)

  Thank you

  Jamal

  Hi Jamal,.

  Just to add to the great info of Robert (+ 5 points Robert)

  The feature you're looking for is called WLAN substitute in versions 4.x WLC.

  Allowing substitution WLAN

  By default, all defined WLAN transmission on the controller access points. However, you can use WLAN editable to select WLAN is transmitted and who are not on a per access point basis. For example, you can use WLAN to control override goes where in the guest WLAN network or you can use it to disable a specific WLAN in a certain area of the network.

  This doc.

  http://www.Cisco.com/en/us/docs/wireless/controller/4.0/Configuration/Guide/c40wlan.html#wp1114777

  Once you create a new WLAN, WLAN > page edition for the new WLAN. In this page, you can set various parameters specific to this general policy, RADIUS servers, political security WLAN key, and 802.1 x settings.

  * Check Admin status under general strategies to activate the WLAN. If you want AP broadcast the SSID in beacon frames, check the SSID broadcast.

  Note: You can configure up to 16 WLAN on the controller. The Cisco WLAN Solution can control up to sixteen WLAN for Lightweight APs. Each WLAN has an ID separated from WLAN (1 to 16), a WLAN SSID (name of the WLAN) separate and can be assigned to single security policies. Lightweight APs broadcast all Cisco WIFI WLAN SSID Solution assets and apply the policies that you set for each WLAN.

  The good doc.

  http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_example09186a0080665d18.shtml#C3

  In versions 5.x, you will use AP groups, because in versions 5.x WLC, WLAN substitute has been replaced by the "Groups of AP" feature;

  Creation of groups access Point

  After all the access points have joined the controller, you can create up to 150 groups of access point and assign up to 16 local wireless networks in each group. Each access point announces that the WLAN enabled that belong to his group of access point. The access point no announcement not disabled WLAN in its access point group or WLAN that belong to another group.

  http://www.Cisco.com/en/us/docs/wireless/controller/5.2/configuration/guide/c52wlan.html#wp1128591

  To learn more about George video AP discover excellent groups

  http://www.my80211.com/Cisco-Labs/2009/3/22/Cisco-AP-group-nugget.html

  I hope this helps!

  Rob

• hp7520 disable wireless or hide the SSID

  Hello.

  I have a HP Photosmart 7520.

  It works fine except my client does not want the ssid broadcast in the doctor's office.

  It is already password protected, but he dislikes the ssid 'disorder' in the air.

  I would like to disable Wi - Fi to the printer or at least hide the ssid broadcast.

  Is this possible?

  Thank you.

  Go to the printer and turn off wireless Direct.  Quite.  This assuming the printer is connected to the router.

• EA2700 smart wifi keeps bug broadcast even if SSID wireless disabled

  Ver.1.1.39.145204 is the firmware.

  Cutting the 2.4 Ghz and 5 Ghz wifi does not interrupt the transmission of a SSID.

  If allow wireless admin is checked the continuous SSID broadcasting on 5 GHz and 2.4 Ghz bands.

  If not checked the SSID then forwards on the 5 GHz band.

  In both cases, the SSID is transmitted are the default SSID of the factory, and he announced a nonsecure connection.  (router erases your security settings when you turn off a radio)

  On the plus side tent to connect to the wrong ssid broadcast failed, but he always seems a bad idea to advertising a connection open 24 hours a day.

  I tried to report it to the Linksys technical support.  Their response was to reload the firmware.  That I did - but it does not change the behavior of this SSID bug.  I asked them to report it as a bug and the Lady declined.

  Does anyone know how to make a break from the SSID when Wifi is disabled?

  Thanks for the reply.  After reboot, then reload the firmware and then reboot the router, five times the problem disappeared.

  I was using an IPAD with IOS 7.1 and a samsung with android phone to test.

• Cisco Aironet 1131AG and measure access points to the power of the wireless signal?

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

  We have about forty points of access Cisco Aironet 1131AG spread over four floors and they all have a static IP (BVI1) on the same SSID, customers will be on its own virtual local area network (dhcp on 3750 switch) and they use several channels (1,6,11).  Cisco Wireless Control System is pending. This wireless network should support roaming for customers (there will be Wi - Fi tags of multiple AeroScout and wireless laptops). To measure the strength of the wireless signal and wireless coverage on each floor. My questions are:

  1. How to measure the strength of the wireless signal: we must meet at least three APs available with signal excellent (I guess for the WCS needs that will determine the position of the client in the building)? We thought to use NetStumbler and a few laptops with wifi and measure as many points as we can as simpler thing. Or should we use something like Cisco Aironet Client adapters for our mobile phone and then use Cisco Aironet Client Utility (is it worth buying for our analysis and measurement)? Any other idea?
  2. What signal level should we consider for a good wireless (dBm)?
  3. That we should propose for authentication, authorization and management accounting? What happens to the roaming wireless? I did not quiteunderstand WCS, WDS and WLC-that should be used for above tasks?

  Thanks in advance.

  "Use the command on the AP" sh dot11 associations "will give you the clients associated with success.  If you add the MAC address of the client at the end of the command, you will get detailed information.  Look under "Signal Strength" and "Signal to noise".  Under the strength of the Signal, you want a value of-75 dBm or lower (lower values the better).  -76 dBm and is bad.  Under Signal-noise, you want a value of 25 dBm or more (values higher the better).

  To measure the strength of the signal, I use Airmagnet, but you can use Netstumbler or Cisco Wireless Site Survey.

• Several points of access Cisco Aironet 1131AG and same SSID?

  We have several Cisco Aironet 1131AG, all wired devices on a switch (2560) Cisco L2 which is connected to the L3 switch (3550). We have assigned a VLAN for access point to the L3 switch which acts as a vtp Server (L2 switch is vtp client). All the ap will have a static ip address and all will have the same SSID and no security, and they will use several channels (e.g. 1,6,11).  They will work in 3 floors for a roaming wireless client. We not using any wireless controller.

  So my question is this: how to configure the same APs-all with a different ip address, can we use L3 switch to create the dhcp server to access points VLAN (pool for guests) and the rest of the static ip address for the ap? One of the ap can be WDS and on the same radius server local time with users without Cisco Secure ACS or similar controller or I did not understand this very well :-). I followed the guide http://www.cisco.com/en/US/docs/wireless/access_point/12.3_2_JA/configuration/guide/s32roamg.html for WDS where Abu Cisco ACS part is a problem, so I can use the same ap as a Local authenticator as a guide http://www.cisco.com/en/US/docs/wireless/access_point/12.3_4_JA/configuration/guide/s34local.html#wp1035723.

  Thank you very much...

  Well, just so you know, WDS, and local RADIUS authentication is necessary only if you use authentication on your wireless connection.  You say that you do not plan to use security, so it's not necessary.  However, I highly recommend at least using a simple WPA2-PSK to lock your connection, otherwise you might end up giving free Internet access at best and at worst you could give access to the computers and corporate servers.  If you want to reuse a 802. 1 x or WPA authentication method, then Yes, you can use an AP as RADIUS and to improve WDS Server authenticated to roaming, but this is much more limited than the use of a Cisco ACS.

  As for your other questions, Yes, your APs can all be configured the same except for at least three settings: IP address, hostname, and channel.  Configure your static IP addresses on the interface of the PA BVI1.  Do not place it on the Radio or Ethernet interfaces, because if one of these interfaces goes down, you lose the ability to configure the AP, so it's best to use the BVI1 interface.

  And Yes, configure a DHCP scope for your customers on your L3 switch is good design, or you can also use your DHCP server on a different subnet by using the command of support-ip address on the interface of L3.  I hope this helps!  Let me know if you need help to set all this up.

  Merry Christmas!

  Jeff

• Broadcast the ssid on WLC for multiple ssid

  Hello

  I'm looking to broadcast the ssid as 13 on the controller, but another 2 not broadcasting. can we do this? It will be totally 15 SSID, provision of services to clients over several suppliers.

  Thanks in advance

  Hello

  By default, the Cisco access point supports 16 SSID... If you want 15 SSID in werving network customers then its possible at the level of the problems... If the SSID is not broadcast, check if customers correctly enter the credentials and create a manual profile on the laptop or something... it will work.

  Let me know if that answers your question...

  Concerning
  Surendra
  ====
  Please do not forget to note positions that answered your question and mark as answer or was useful

• WiFi does not connect if the SSID is not broadcast.

  I've updated to Sierra this afternoon. Everything seemed fine after the update. After dinner, my MacBook Pro (retina, 15 inches, beginning 2013) would not connect to Wifi. I reduced to a few things.

  It wouldn't connect the 5 GHz n If the SSID has been hidden. If I admitted the SSID to shown, it would connect without problems. It would connect to the 2 GHz band, even with the hidden SSID.

  I did the typical SMC reset and reset the NVRAM. I deleted the files related wifi and restarted the router and the MBP. I'm obviously on now and the speed seems normal with no dropouts. I can't hide the SSID now and will continue to work until he's asleep; No dice after that without reactivation SSID broadcast.

  Any thoughts?

  See you soon,.

  Fred

  With your same Apple ID, you can register for a free developer account and start a conversation with Apple engineers. They will answer your question: Bug Reporter https://bugreport.apple.com/