Defining a 1852nd Aironet AP - Radio Off - Cisco IOS 12.3 (4) JA
I have a brand new Cisco Aironet 1800 AP series I'm trying to install. Specifically the 1852E. I do not have a controller and try to use the method of deployment of mobility Express. When I received the unit there is a yellow label more precisely declaring outside: "OFF BY DEFAULT note RADIOS: radios are disabled by default for Cisco IOS releases 12.3 (4) JA and later.
If anyone can please tell me how I am supposed to this access point configuration when the radios are not suite, so the CiscoAirProvision SSID is not broadcast?
I tried the following:
1 connect the unit to my PoE switch. Unit Gets power and discovery mode starts (red/orange/green light cycling). He succeeded receives an IP address from my DHCP.
2. when I try to access the device through my laptop via the local LAN it just times out. Pings meet.
I apologize if my post seems harsh, I am quite agitated that even after having spent more than 5 hours trying to troubleshoot and get this thing to work, there was nothing else than a nightmare (both for the installation of touted 10 min). I do RTFM. I missed something simple jumps? or am I just to assume that Cisco has really missed the boat the patch appropriate for an assignment in their literature.
FOR INFO. Thorough searches Google and research on this forum gave me no help.
Thank you.
Convert a CAWAP AP an AP express mobility
Tags: Cisco Wireless
Similar Questions
-
Portege R500 - Novatel Wireless Radio off
Hello
I've seen a few posts on here suggesting various downloads and updates to solve problems with 3 G connectivity, but none of these downloads have worked for me.
Novatel loads OK... but reports still no Service - Radio Off... I can't find a way to get "Radio on" or any info on what might be the issue...
Any help at all would be great!
Dave L
Hello
Are maybe something stupid but you sure that you have an internal 3G module?
As far as I know not all models are equipped with this feature to check this first, please!
-
IdeaPad Z50-70 wireless - hardware radio off
Hello
I have a Lenovo IdeaPad Z50-70, and for almost 2 days, I see that my wireless connections are not work / appear. Until about 2 days ago worked well all.
It is said "hardware radio off", I looked on google but found nothing yet, I tried to 'Reset PROSet' but still, after the reboot, it is the same problem.
It is not a big problem, because I use an internet cable and everything works fine, but because it's a laptop, so I want to buy a router there is the problem, I can buy it but will not work... like the wireless.
How can I fix it? How to turn on radio equipment? Is there a button or a key combination?
Sorry for the late reply, still does not, but I wonder, my F (1, 2, 3... 12) buttons have other functions such as mute F1, F2 F3 adjust sound, F5 Refresh, etc..
Could this be the problem because the F5 bind key refresh or... I mean, and it should do something else that refresh?Update: it's weird, this evening, I came to the College and opened the laptop seems to be that my wireless connections are visible again and work. Still don't know what to do, but I'm glad it is resolved.
Thanks again for the support!
-
SHA version supported on Cisco IOS
Guys,
What is the SHA version that we support on the devices that support VPN from Cisco IOS? Just configuration options tell SHA...
I do apreciate if you could point me to a cisco document to support your theory because client would require...
Thanks in advance.
hash (IKE policy)
To specify the hashing algorithm in a policy of Internet Key Exchange, use the command hash policy Internet Security Association Key Management Protocol (ISAKMP) configuration mode. IKE policy define a set of parameters to use when the IKE negotiation. To reset the hash algorithm for the algorithm of hash-1 defaultsecure hash algorithm (SHA), don't use No form of this command.
hash {sha | SHA256 . SHA384 | md5}
no hash
Description of the syntax
SHA
Specifies the hash algorithm SHA-1 (HMAC variant).
SHA256
Specifies the family of SHA-2 256 bits (HMAC variant) as the hashing algorithm.
SHA384
Specifies the family of SHA-2 384 bits (HMAC variant) as the hashing algorithm.
MD5
Specifies the MD5 (HMAC variant) as the hashing algorithm.
Default values
The SHA-1 hashing algorithm
Control modes
The ISAKMP policy configuration
Order history
ReleaseChange11.3 T
This command was introduced.
12.4 (4) T
IPv6 support has been added.
12.2 (33) SRA
This command was integrated into Cisco IOS version 12. (33) SRA.
12.2SX
This command is supported in the Cisco IOS release 12.2SX train. Support in a specific 12.2SX release this train is dependent on your hardware platform game and platform functionality.
Cisco IOS XE version 2.1
This command was introduced on the ASR 1000 series Cisco routers.
15.1 (2) T
This command was modified. Sha256 , sha384 , and keywords have been added.
Of course, depends a bit on your IOS.HTH,Ian -
Cisco IOS DHCP Server + classless static routes on DHCP clients
Hi, I tried to find if it is possible to add the ability for static routes to DHCP clients on the Cisco IOS DHCP configuration mode. I'm looking to add a parameters as defined in RFC 3442, like this one, located on the ISC DHCPd server:
Global settings:
121 = integer table 8 code option rfc3442-classless-static-routes;
ms-classless-static-routes option code 249 = integer table 8;
And for the subnet declaration:
option rfc3442-classless-static-routes 24, 192, 168, 30, 192, 168, 10, 1;
option 24 ms-classless-static-routes, 192, 168, 30, 92, 168, 10, 1;
Is this possible?
Thank you!
Vitor
Yes, the fun part it is to convert it into a format IOS will accept. You can try:
IP dhcp pool 0
option 121 24.192.168.30 ip 192.168.10.1
option 249 ip 24.192.168.30 92.168.10.1
If this does not work, change the "intellectual property" for "hex" and each of your decimal byte converted to hexadecimal.
-
Where can I download Cisco IOS Software
Please can someone give me where should I always upload images of Cisco IOS
Thank you very much
Directly to the source:
http://www.Cisco.com/Cisco/software/Navigator.html
Note that an ORC (Cisco connection) and the valid service contract are necessary for the number of items.
Best regards
Ed
-
Cisco IOS Software Internet Key Exchange vulnerability Enquiry
Cisco IOS devices are vulnerable when you run a software image of an affected version of the Cisco IOS software that does not support the IKE version 2 (IKEv2) and is configured to use IKE version 1 (IKEv1).
Vulnerable products
This vulnerability affects Cisco IOS 15.1GC, 15.1 T software version trains and 15.1XB. No other Cisco IOS software release trains are affected.Ref: http://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20130327-ike
If we use "not affected (for example; version". 12.4, 15.0 releases)"and configured with IKE version1? Can it be affected by this vulnerability?
Subsys router #sh | include ikev2
ikev2_cli_registry registry 1.000.001
Thank you best regards &,.
Ye
You are not affected by this vulnerability.
As described in the notice - "There is no affected 12.4 based rejection" and «There is no rejection of base affected 15.0»
-
Cisco IOS router 837 - configure DDNS / dynamic DNS
I have an Internet, connected to my Cisco router link. The package that I subscribed comes with a dynamic IP address. I said me, if I need remote access in the Cisco router, I need to enable the DDNS function. Is this possible on a Cisco router? I have been informed that this feature is not supported. Please help me
Hi Bro
Yes, Cisco ASA and Cisco IOS router supported DDNS. Just make sure you have the right version of IOS, which you could refer to this URL of Cisco http://www.cisco.com/en/US/docs/ios/12_3/12_3y/12_3ya8/gt_ddns.html#wp1202953.
Please refer to the config below made with dyndns.org.
!
hostname INT-RTR1
!
IP domain name dyndns.org
8.8.8.8 IP name-server
!
IP ddns update DynDNS method
HTTP
Add http://ramraj: [email protected] / * //nic/update?system=dyndns&hostname=&myip=>
maximum interval of 30 0 0 0
minimum interval 30 0 0 0
!
interface Dialer1
IP ddns update hostname INT - RTR1.dyndns.org
IP ddns update DynDNS
!Note: hostname = INT - RTR1.dyndns.org was the host added/registered in the dyndns.org site.
Note: Press Ctrl + V, then just type the symbol? When to add the CLI adds http://___ above.
Note: ramraj:cisco123 is simply an example of an IDs in dyndns.org.
You can also refer to this URL for more details http://www.petri.co.il/csc_configuring_dynamic_dns_in_cisco_ios.htm
P/S: If you cela this comment is useful, please rate well :-)
-
Cisco IOS server certificate - is it supported on routers 857/877
Please can someone confirm if the certificate of Cisco IOS server feature is supported on the Cisco 857 router. We have checked with the Software Advisor and no picture for the 857 when the server certificate of IOS feature is selected, but advancedIpservices image v 12.4 (11) T arrives to the 877.
The two 857/877 supports IOS server Certificate
to 857 you need the ADVANCED SECURITY feature set 12.3 (14) YT
877 offers more IOSes with Certificate server supports when I chose the certificate server Cisco IOS feature with featured navigator I got a lot of IOSes supporting this feature
Go to navigator feature
http://Tools.Cisco.com/ITDIT/CFN/JSP/index.jsp
Select search by function and select element Cisco IOS Certificate Server, you can filter the results by platform (857/877)
M.
-
Team,
I use software Cisco IOS XE, Version 03.15.00.S - Standard Support version Cisco IOS software, software of CSR1000V (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5 (2) S, (fc3) SOFTWARE VERSION to support my Cisco IOS CA.
In short, I am trying to support a FlexVPN - client VPN Win7 according to document tac 115907 id
In this document, he says that OpenSSL CA is used but a Cisco IOS CA can also be used. In tests I am at a point where my certificates do not match the example:
The example document TAC:
X509v3 extensions:
X509v3 Key use: F0000000
Digital signatureNon-repudiation
Encryption keyData encryption
My version of laboratory:
X509v3 extensions:
X509v3 Key use: A0000000
Digital signature
Encryption keyHow can question - I get these replacement using the IOS Cisco CA extensions?
Chris
Chris,
(Shameless Plug) take a look at IOS CA config I used:
http://www.Cisco.com/c/en/us/support/docs/security/flexvpn/115014-flexvp...
M.
-
Hello, my question is if you need to configure the router Cisco IOS XR-activated (it is a series of 12 k by-the-by) differently on the side of the ACS or is it added like any other normal router.
Hi raul,.
the ios - xr router will act as a NAS for the candidate countries. If the configuration will be the same as any other NAS on GBA.
Kind regards
Anisha
P.S.: Please mark this thread as answered if you feel that your query is resloved
-
Hi, just got our Cisco 3850 switch newly shipped with IOS - XE. Here is an example of the command 'show version '.
Switch(Config-if) #do show worm
Cisco IOS software, IOS - XE software, catalyst L3 Switch (CAT3K_CAA-UNIVERSALK9-M), Version 03.02.03.SE VERSION SOFTWARE (fc2)
Technical support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Last update Mon 23 - Sep - 13 18:24 by prod_rel_teamCisco IOS Software - XE, Copyright (c) 2005-2013 by cisco Systems, Inc.
All rights reserved. Some components of the Cisco IOS - XE software are
distributed under the GNU General Public License ("GPL") Version 2.0. The
software licensed code GPL Version 2.0 is a free software that comes
WITHOUT ANY WARRANTY. You can redistribute it and/or modify it
Code GPL under the terms of the GPL Version 2.0.
(http://www.gnu.org/licenses/gpl-2.0.html) For more details, see the
documentation or "Mention of license" file that accompanies the IOS - XE software.
or the applicable URL listed on the brochure that accompanies the IOS - XE
software.ROM: IOS - XE ROMMON
BOOTLDR: CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) 1.18 Version, SOFTWARE VERSION (P)
The availability of HK-CSW001 is 4 hours, 0 minutes
Availability for this command processor is 4 hours, 3 minutes
System return to the ROM to reload
System image file is "flash: packages.conf.
Reload last reason: reload the commandThis product contains cryptographic features and is under the United States
States and local laws governing the import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third party approval to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. laws and local countries. By using this product you
agree to comply with the regulations and laws in force. If you are unable
to satisfy the United States and local laws, return the product.A summary of U.S. laws governing Cisco cryptographic products to:
http://www.Cisco.com/WWL/export/crypto/tool/stqrg.htmlIf you need assistance please contact us by mail at
[email protected] / * /.License level: Ipbase
License type: Permanent
Then reload license level: IpbaseCisco WS-C3850-24 t (MIPS) processor with K 4194304 bytes of physical memory.
Card processor ID FOC2007U0YG
2 virtual Ethernet interfaces
28 gigabit Ethernet interfaces
4 ten interfaces Ethernet Gigabit
2048K bytes of non-volatile configuration memory.
K 4194304 bytes of physical memory.
250456K bytes of Crash crashinfo files:.
1609272K bytes of Flash Flash:.
0K bytes of Flash model to usbflash0:.
0K bytes of to webui::.MAC Ethernet base address: 00:cc:fc:d1:55:80
Motherboard Assembly number: 73-16297-04
Motherboard serial number: FOC20061W6G
Revision number of the model: Z0
Motherboard revision number: B0
Model number: WS-C3850-24 t
System serial number: XXXXXXXXXXXMy problem is, I tried to HSRP 1 before using a plotter package and thought since he succeeded, I could do it here in this new switch, but after reading a few articles 1 HSRP went and here HSRP 2 but after I typed in the
"interface vlan XXX".
"ip address subnet XXX.XXX.XXX.XXX.
command "watch version 2" is not available or the day before ipXXX XX. is not available either.
I'm stuck with this problem now, appreciate any help from you guys.
Thank you
The f
Hello Jeff,.
We were also quite surprised at the point where we realized, that our brand new 3850 did not support HSRP. This feature was introduced in a second version of the IOS - XE. Currently, we run 03.06.00.E on our WS-C3850-24 t and this version support HSRP.
I don't understand absolutely, why Cisco released such a combo of software/switch isn't over.
So, please try a newer version of the software.
See you soon
Ichnafi
Supplement: Cisco Feature Navigator (http://tools.cisco.com/ITDIT/CFN/jsp/by-feature-technology.jsp) said: HSRP is supported since Version 3.3.0
-
Cisco IOS device - password enable
Y at - there a trick to getting the password to enable working on Cisco's IOS device?
I created my first workflow to connect to a Cisco IOS device recently and initially could not do the work of enable mode.
Using activity "Send commands to the Interface", I run the command "enable."
From there on, the activity times out.
The goal is to use the Cisco IOS expect model, I noticed the option 'raising command privilege '.
How is it used? Should expect model automatically detect the order of lifting and then use awaits below?
If so, it doesn't seem to work.
The only way I could make it work was to add my own manual expect activity "send commands to the Interface. I used the targets 'Elevation of privilege command' variable reference as await them and sent the password for admin users in response.
It is to open the model waiting for you to use an order of elevation. If you select not those expect the models and you run an 'enable' command and you command prompt, turned to the sign ' # ', then it would not be all wait would expire models and additional orders and not work.
-shaun
-
Cisco IOS - failed login Admin
Hello
I configured Cisco IOS to authenticate via a server RADIUS (Cisco's ISE). By mistakely I put all authentication via RADIUS only.
Now, I can not connect via RADIUS but unable to connect through credetials local Admin of Cisco IOS and for this reason I am not able to access the privileged commands.
Is there a way back so this connection by admin (SMAP) would be possible and not on the SHELF?
I do not have access to 'configure', 'enable the RADIUS user commands '.
That worked before? BTW, what code IOS are you running?
What error you see on the IOS command line interface when ISE is DOWN and you're trying to connect with the local user account?
Do you have local authentication as a method of failover? You have paper before IOS config you locked?
You can check that the ISE live authentication records if the user is authenticated by the radius server. Can you use the RADIUS credentials, go to LSE > operations > authentication > records messages.
Did you write the changes? If this is not the case, the last resort would be to RELOAD.
~ BR
Jatin kone* Does the rate of useful messages *.
-
Hello
I want to know can I use the Cisco IOS SSL VPN on the use of mobile client Anyconnect. If yes what is the prerequisite, is there any kind of additional license required.
Thank you
In the following article:
http://www.Cisco.com/c/en/us/support/docs/security/AnyConnect-VPN-client...
Q. is possible to connect the iPad, iPod or iPhone AnyConnect VPN Client to a Cisco IOS router?
A. No. it is not possible to connect the iPad, iPod or iPhone AnyConnect VPN Client to a Cisco IOS router. AnyConnect on iPad/iPhone can connect only to an ASA that is running version 3,0000.1 or a later version. Cisco IOS is not supported by the AnyConnect VPN Client for Apple iOS. For more information, refer to the section security devices and software support to the Release Notes for Cisco AnyConnect Secure Mobility Client 2.4, Apple iOS 4.2 and 4.3.
--
Please do not forget to rate and choose a good answer
Maybe you are looking for
-
I add old family photos to Photos. I know generally where these pictures were taken, but do not know the exact location. Hami to enter a generic place - "Indiana" or "Randolph County, Indiana" - Photos does not accept the location and I end up with a
-
My battery life is now up to two hours, which is a problem for my work... How can I get this resolved? My computer laptop 15 "retina is 3 years old.
-
I finished building the Web site for my girlfriend, and the rest is the RSS feed. It works just fine in IE 8, but Fire Fox 9 when the widget is clicked a bookmark box appears and asks if I want to save it as a bookmark. I'm not a programmer of the Ja
-
Canon printer does not connect via the IPP Protocol
I work in a company that sells printers offices/schools/etc. Yesterday, we received a call from a customer indicating that the Copier, we sold them connected not to a new computer they bought. I went to the site and noticed that the computers in ques
-
Qosmio G20 with Intervideo WinDVR3
Hello I have a laptop Qosmio G20/395LS (purchased at the Japan) that since I converted to English Windows XP Pro SP2. I then downloaded all the drivers from Toshiba on the site of Toshiba UK, choosing the Qosmio PQG20, which is the closest model from