All-round Vpn connection with EZVpn

Similar Questions

• VPN connection with external modem

  Cisco 2651XM router

  using a wic adsl card I was able to establish a vpn connection from a computer on to my 2651xm router cisco vpn client successfully, but I can't get a connection using an external modem.

  My local network at the end of the vpn server is on 172.16.1.xx and goes into the router on f0/0, which stood at 172.16.1.30.

  Port f0/1 is 192.168.1.100 and goes to an external modem set as default gateway

  192.169.1.254. with this configuration I can surf the internet on the computers in the lan at the server end.

  Problem is that I can't get a connection from a remote machine VPN connect. It worked when I used the wic adsl connection, but then I used only

  the port of f0/0 that was connected to my local network. But now I'm including the f0/1 port to connect to an external modem, vpn client cannot connect. The cisco vpn client tries to connect by using tcp on port 10000 and I have to configure it in the modem, but do not know if I did it correctly. I tried to transmit the port both 192.168.1.100 (f0/1) and 172.16.1.30 (f0/0), but neither will not work. My config running is attached. Thanks for the pointers.

  ----------------------

  #show running-config router

  Building configuration...

  Current configuration: 2757 bytes

  !

  version 12.4

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  no password encryption service

  !

  vpn hostname

  !

  boot-start-marker

  boot-end-marker

  !

  no set record in buffered memory

  no console logging

  enable secret 5 xxxxxxxxxxxxxxxxxxxxxxxxxxxxx

  activate the password xxxxxxxxxxx

  !

  AAA new-model

  !

  !

  AAA authentication login default local

  AAA authentication login sdm_vpn_xauth_ml_1 local

  AAA authentication login sdm_vpn_xauth_ml_2 local

  AAA authorization sdm_vpn_group_ml_1 LAN

  AAA authorization sdm_vpn_group_ml_2 LAN

  !

  AAA - the id of the joint session

  !

  resources policy

  !

  no location network-clock-participate 1

  No network-clock-participate wic 0

  IP cef

  !

  !

  !

  !

  name-server IP 192.168.1.254

  name-server IP 192.168.1.255

  IP ddns update method sdm_ddns1

  DDNS both

  !

  !

  !

  !

  !

  username secret xxxxxxxxxxx 5 xxxxxxxxxxxxxxxxxxxxxxxxxx

  !

  !

  !

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  !

  ISAKMP crypto client configuration group workgroup

  vpnkey key

  pool SDM_POOL_2

  ISAKMP crypto sdm-ike-profile-1 profile

  match of group identity working group

  client authentication list sdm_vpn_xauth_ml_2

  ISAKMP authorization list sdm_vpn_group_ml_2

  client configuration address respond

  virtual-model 2

  !

  !

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-3DES-SHA1 esp-3des esp-sha-hmac

  !

  Profile of crypto ipsec SDM_Profile1

  game of transformation-ESP-3DES-SHA1

  isakmp-profile sdm-ike-profile-1 game

  !

  !

  !

  !

  !

  ATM0/0 interface

  no ip address

  Shutdown

  No atm ilmi-keepalive

  DSL-automatic operation mode

  !

  interface FastEthernet0/0

  IP 172.16.1.30 255.255.0.0

  IP nat inside

  IP virtual-reassembly

  automatic speed

  Half duplex

  No mop enabled

  !

  interface FastEthernet0/1

  Description $ETH - WAN$

  updated client dns IP dhcp-server no

  IP ddns update hostname vpn.vpn

  IP ddns update sdm_ddns1

  dhcp customer_id FastEthernet0/1 IP address

  NAT outside IP

  IP virtual-reassembly

  automatic duplex

  automatic speed

  !

  tunnel type of interface virtual-Template2

  IP unnumbered FastEthernet0/1

  ipv4 ipsec tunnel mode

  Tunnel SDM_Profile1 ipsec protection profile

  !

  router RIP

  version 2

  network 172.16.0.0

  network 192.168.1.0

  No Auto-resume

  !

  local IP 192.168.1.110 SDM_POOL_1 pool 192.168.1.120

  local IP SDM_POOL_2 172.16.1.21 pool 172.16.1.29

  !

  !

  IP http server

  no ip http secure server

  IP nat inside source list 3 interface FastEthernet0/1 overload

  !

  Remark SDM_ACL category of access list 1 = 2

  access-list 1 permit 172.16.0.0 0.0.255.255

  Note access-list 2 = 2 SDM_ACL category

  access-list 2 allow to 192.168.1.0 0.0.0.255

  Remark SDM_ACL category from the list to access 3 = 2

  access-list 3 permit 172.16.0.0 0.0.255.255

  !

  !

  !

  !

  control plan

  !

  !

  !

  !

  Line con 0

  line to 0

  line vty 0 4

  password: xxxxxxxx

  !

  !

  end

  Hello

  On the ADSL Modem, you must before 500, port 4500 UDP and 10,000 to the IP address of the router.

  Basically, tell you the Modem to 192.168.1.100 transmitting any packet received on 192.169.1.254.

  On the client VPN choose encapsulation UDP NAT, make use of NAT - T standard.

  Please rate if this helped.

  Kind regards

  Daniel

• Impossible to establish a VPN connection with a router configured as a Cisco server using client VPN 5.0.00.0340

  Hei guys,.

  Please help me on this one because I'm stuck enough on her...

  I am trying to connect to a Cisco 3700 router configured as a VPN server by using a VPN client and the VPN connection does not settle.

  This is an extract from the log:

  130 12:48:30.585 07/01/11 Sev = Info/5 IKE / 0 x 63000001
  Peer supports XAUTH
  131 12:48:30.585 07/01/11 Sev = WARNING/3 IKE/0xE3000057
  The HASH payload received cannot be verified
  132 12:48:30.600 07/01/11 Sev = WARNING/2 IKE/0xE300007E
  Failed the hash check... may be configured with password invalid group.
  133 12:48:30.600 07/01/11 Sev = WARNING/2 IKE/0xE300009B
  Impossible to authenticate peers (Navigator: 904)
  134 12:48:30.600 07/01/11 Sev = Info/4 IKE / 0 x 63000013
  SEND to > ISAKMP OAK INFO (NOTIFY: INVALID_HASH_INFO) for 200.100.50.173

  I enclose the whole journal extract... The message "BOLD" is quite obvious, you mean, but I'm 100% sure, in the login entry, I typed correctly the group password: pass

  My topology is very basic, as I am setting this up only to get a clue of the operation of the Cisco VPN. It is built in GNS3:
  -2 3700 routers: one of them holds the configuration of the VPN server and the other would be the ISP through which the remote worker would try to establish a VPN connection. I am also attaching the configuration file for the router configured as a VPN router.

  Behind the second router there is a virtual XP machine on which I have installed VPN client...

  My connection entry in the customer is to have the following parameters:
  Host: 200.100.50.173 , //which is the IP address of the VPNServer
  Authentication-> authentication-> name group: grup1 password: pass / / I'm quite positive that I typed the correct password... even if the log messages are linked to a misidentification.

  I use public addresses only, because I noticed there is a question about behind the NAT VPN connections and is not not very familiar to the NAT.

  Another aspect which can be of any importance is that "allow Tunneling of Transport" in the tab Transport to the input connection is disabled

  and the VPNServer router logs the following error message when you try to establish the connection:

  * 01:08:47.147 Mar 1: % CRYPTO-6-IKMP_NOT_ENCRYPTED: IKE 200.100.50.34 package was not encrypted and it should have been.
  * 01:08:47.151 Mar 1: % CRYPTO-6-IKMP_NOT_ENCRYPTED: IKE 200.100.50.34 package was not encrypted and it should have been.
  

  You have no idea why I can't connect? Y at - it something wrong with my configuration of VPN server... or with the connection entry in the VPN client?

  Thank you

  Iulia

  Depending on the configuration of the router, the group name is grup1 and the password is baby.

  You also lack the ipsec processing game that you would need to apply to the dynamic map.

  Here is an example configuration for your reference:

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080235197.shtml

  Hope that helps.

• No Internet connectivity with ASA 5505 VPN remote access

  Hello

  I configured ASA 5505 for remote access VPN to allow a remote user to connect to the Remote LAN officce. VPN works well, users can access Office Resource of LAN with sahred etc., but once they have connected to the VPN, they are unable to browse the internet?

  Internet navigation stop working as soon as their customer VPN connect with ASA 5505 t, once they are disconnected from VPN, once again they can browse the internet.

  Not ASA 5505 blocking browsing the internet for users of VPN? Is there anything else that I need congfure to ensure that VPN users can browse the internet?

  I have to configure Split Tunnleing, NATing or routing for VPN users? or something else.

  Thank you very much for you help.

  Concerning

  Salman

  Salman

  What you run into is a default behavior of the ASA in which she will not route traffic back on the same interface on which he arrived. So if the VPN traffic arrived on the external interface the ASA does not want to send back on the external interface for Internet access.

  You have at least 2 options:

  -You can configure split tunneling, as you mention, and this would surf the Internet to continue during the use of VPN.

  -You can set an option on the ASA to allow traffic back on the same interface (this is sometimes called crossed). Use the command

  permit same-security-traffic intra-interface

  HTH

  Rick

• Remote VPN connection double

  Hello guys

  I have created three different remote VPN connections with three different networks. I can do the reasons but for some I don't mix everything.

  and iam with Cisco asa 5505 software Shrew Soft VPN, then my problem is

  -J' connected Shrew soft vpn remote, if I try to connected another remote vpn connection that will not accept the second connection, so please can someone give me a remote vpn connection software that accepts multiple connections

  Hello

  Since you mention the ASA and the VPN, I guess you are trying to connect by VPN Client to the same ASA?

  Why would you want to have multiple connections from VPN clients at the same time? (Although I think that it is not yet possible)

  What are you trying to accomplish in these 3 different configurations of Client VPN configured on the same ASA?

  is it not just possible to configure a VPN Client to ASA connection that would treat all traffic from these 3 VPN Client connections?

  -Jouni

• I'm having a problem when I try to establish a VPN connection

  I have a problem when I try to establish a VPN connection between a remote computer and my desktop computer that we use as a file server in our network of workplaces. It has a static IP address. The VPN connection was working until the person on the other side you have forgotten the password. We decided to set up a new connection with the new user name and password. The remote computer could not establish a VPN connection with the server, but when the person on the other side tried to open the files, she received a message indicating there is no permission to do so. I can't understand how to give the person permission to open folders. Can anyone help?

  Hello

  Thanks for posting in the Microsoft Community.

  The question you posted would be better suited in the TechNet community.
  http://social.technet.Microsoft.com/forums/en/w7itprogeneral/threads

  I hope this helps!

• Can connect with desktop remotely all directions except via internet Windows XP to Windows 7

  I have a new computer with Windows 7 Pro to work I need with desktop remote access so that I can work from home and be with the family.  For years I used remote desktop connection from home using Win XP SP3 to my Win XP Pro SP3 computer at work.  I am able to connect my old WinXP computer work on my new Win 7 computer (locally).  I can connect from home computer Win XP Win XP computer via internet (DSL) to work.  I can connect from Windows 7 computer to work at Windows XP home computer over the internet (DSL).

  So, I have Setup port forwarding or modems DSL correctly, the IP addresses are correct, consistent remote desktop clients. Firewall exceptions are configured correctly.

  What is different.  The new computer with Windows 7 Pro has McAfee Internet Security all others running EAST of Kaspersky.  Win 7 computer is new.  Since I am on various possibilities of connections, changed listening port of 3389 on some computers, including the new Win7 computer (this should not be a problem that I'm able to connect locally).

  Disable the firewall (software Anti-anti-virus/IS) on both computers does not help. In any case, I can go to WinXP Pro to work on Win 7 computer to work locally.

  My thought is that there may some security policies, or maybe a protocol problem which is different with the new Windows 7 computer that does not have a connection outside the local network (via a public network).

  I also tried to set up a VPN connection integrated Microsoft: forwarded port 1723, the GRE protocol allowed to the DSL modem.  Tried all different scenarios between Win XP Home and Win 7 computer at work and cannot configure the VPN connection. I get error 678: the remote computer did not respond.

  I spent hundreds of discussions help/knowledge base and discussion review.  I have seen or followed all the instructions on the various sites of tech Web to configure VPN connections and Remote Desktop connections.

  Does anyone have an idea as to what could be the solution here?

  Hello

  Please post your request in the Microsoft TechNet forum, where experts on this platform can help you with the problem.

  Please see the link that will take you on the TechNet forums below:
   
  https://social.technet.Microsoft.com/forums/en-us/home?category=w7itpro

  Hope this information helps. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

• Connection with the client VPN for RV110W problem

  Hi guys: I just installed a RV110W router to my small business and I try to connect via VPN from home client.  I was unable to do so, no matter what I try.  Relevant information:

  1. I can connect to the router via remote very well management, so I know that the router is accessible from the Net.

  2. internal address of the router: 10.81.208.1

  3. active PPTP.  PPTP server IP address: 10.0.0.1

  4 IP addresses for PPTP clients: 10.0.0.10 - 14

  5. two VPN clients added - one with PPTP, with the QuickVPN Protocol Protocol.  Both are enabled (and Yes, I triple checked passwords)

  6 encryption MPPE and Netbios active.

  7 IPSec, PPTP and L2TP all active gateways.

  8 VPN client: 1.4.1.2

  9. computer: laptop running Windows 7 family (64-bit), with the firewall Windows is activated.

  10 home network: 192.168.2.196

  It is causing to tear my hair out.  What Miss me?

  Shannon

  Hi Shannon,

  I am pleased to see that you're progress.

  Shannon Rotz wrote:
  I changed the RM port to 443.  Unfortunately, now I can't connect to the router via browser, either by remote management or from the local network - I get the usual "page cannot be displayed".  How do I get back into the router configuration GUI?
  

  You should be able to reach the GUI by typing https://192.168.1.1(assuming that you have not changed the default IP address) normally once you replace http (port 80) with https (port 443) the internal router web server automatically will redirect you to the https page if you type http. Open your command prompt and try to do a ping of the IP address of the router to ensure that it still meets this address

  With regards to the VPN client:   Up until I changed the port, the same error message kept coming up, i.e. "Unable to establish connection" (or something like that), with a list of possible reasons why it couldn't connect. Now the message has changed - I'm getting "Server's certificate doesn't exist on your local computer".  If I continue trying to connect, then it says "Activating Policy", followed by "Verifying Network", then "The remote gateway is not responding.  Do you want to wait?"  This is definitely progress, since I never got this far before.

  You are a quarter inch offline. If you look at the log.txt in C:\Program Cisco Small Business\QuickVPN Client, in my view, you will see "Failed to ping router remote VPN! This means that your PC is blocking the ping to the router response. Usually, if you look at this point the status of Client VPN in the router (first of all need to remote management) you will see that your user status is "connected." If the router thinks that the connection is established, but the PC does not work. You might want to try another PC at this stage to verify that it is indeed a problem with your PC. This problem is usually caused by the 3rd party software antivirus/firewall blocking the ping response. Microsoft Security Essentials can do this as well, so if you turn it off. If you do not have another PC to test from, call Cisco Small Business Support and ask a technician, try to connect to the lab. You can find the number to call here

  On an impulse, I tried setting up a Windows VPN connection, i.e. created a new VPN connection in Network and Sharing Center, using a PPTP client ID that I had created.  That connection actually worked, except for one problem:  I can't see the remote network.  If I could solve that problem, I'll just tell the other clients to use a Windows connection rather than QuickVPN.
  

  Good thought. If you do not see the remote devices, make sure that they do not block VPN connections. (Windows or third-party firewall, antivirus, antispyware) With a connection, PPTP or QuickVPN, you should be able to go to run, type the IP address of the device that you want to connect to (i.e. \\192.168.1.101 ) and see the list of shared folders. After the PPTP connection is established, try to ping the address LAN IP of the router. If it is successful, try to ping a LAN device such as a network printer or a PC. Again, PCs may block ping requests if they have a firewall running watch so for this.

  Answer please if you have any questions.

• 3 RVS 4000 with VPN connection

  Hello

  I want to connect in a triangle 3 RVS 4000 router with VPN

  I configured 3 routers, which can connect to the Internet. Each of them are configured as the gateway.

  I created 2 tunnels on each router. But the vpn connection cannot be established.

  Here is the configuration of ROUTER1 another are configured in the same way, only the remote group configuration is different

  What I also open some ports for VPN, if yes which and were

  Thanks fpr your help and your response

  HP. Meyer

  Hi hanspetermeyer,

  Thank you for posting. You don't need to open all the ports for VPN. I noticed that your screenshot shows two routers have a common LAN subnet of 192.168.100.x. You will need a different local subnet for each router:

  1. 1 router: 192.168.1.1
  2. Router 2: 192.168.2.1
  3. Router 3: 192.168.3.1

  I think that you will find the tunnels only connect once you change the LAN IP of the routers so that they are on different subnets. Please let us know if it works.

• Difficulty accessing 1 remote desktop when connected with VPN

  Hello world

  I have an ASA 5505 and have a problem where when I connect via VPN, I can RDP into a server using its internal address but I can't RDP to another server using its internal address.

  One that I can connect to a an IP of 192.168.2.10 and I can't connect to a a 192.168.2.11 on 3390 port IP address.

  The two rules are configured exactly the same except for the IP addresses and I can't see why I can't connect to this server.

  I am also able to connect to my camera system with an IP on port 37777 192.168.2.25 and able to ping any other device on the network internal.

  I also tried ping he and Telnet to port 3390 without success.

  Here is the config.

  ASA 4,0000 Version 1

  !

  !

  interface Ethernet0/0

  switchport access vlan 3

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  switchport access vlan 2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan2

  nameif inside

  security-level 100

  IP 192.168.2.2 255.255.255.0

  !

  interface Vlan3

  nameif outside

  security-level 0

  10.1.1.1 IP address 255.255.255.0

  !

  passive FTP mode

  clock timezone IS - 5

  clock to summer time EDT recurring

  network obj_any object

  subnet 0.0.0.0 0.0.0.0

  network of the OWTS-LAN-OUT object

  10.1.1.10 range 10.1.1.49

  network of the OWTS-LAN-IN object

  Subnet 192.168.2.0 255.255.255.0

  service of the RDP3389 object

  service destination tcp 3389 eq

  Description of DC

  the object SERVER-IN network

  host 192.168.2.10

  network of the SERVER-OUT object

  Home 10.1.1.50

  network of the CAMERA-IN-TCP object

  Home 192.168.2.25

  network of the CAMERA-OUT object

  Home 10.1.1.51

  service object CAMERA-TCP

  Service tcp destination eq 37777

  the object SERVER-Virt-IN network

  Home 192.168.2.11

  network of the SERVER-Virt-OUT object

  Home 10.1.1.52

  service of the RDP3390 object

  Service tcp destination eq 3390

  Description of VS for Master

  network of the CAMERA-IN-UDP object

  Home 192.168.2.25

  service object CAMERA-UDP

  Service udp destination eq 37778

  the object OWTS LAN OUT VPN network

  subnet 10.1.1.128 255.255.255.128

  the object SERVER-Virt-IN-VPN network

  Home 192.168.2.11

  the object SERVER-IN-VPN network

  host 192.168.2.10

  the object CAMERA-IN-VPN network

  Home 192.168.2.25

  object-group Protocol TCPUDP

  object-protocol udp

  object-tcp protocol

  AnyConnect_Client_Local_Print deny ip extended access list a whole

  AnyConnect_Client_Local_Print list extended access permit tcp any any eq lpd

  Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol

  AnyConnect_Client_Local_Print list extended access permit tcp any any eq 631

  print the access-list AnyConnect_Client_Local_Print Note Windows port

  AnyConnect_Client_Local_Print list extended access permit tcp any any eq 9100

  access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol

  AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.251 eq 5353

  AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol

  AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.252 eq 5355

  Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print

  AnyConnect_Client_Local_Print list extended access permit tcp any any eq 137

  AnyConnect_Client_Local_Print list extended access udp allowed any any eq netbios-ns

  implicit rule of access-list inside1_access_in Note: allow all traffic to less secure networks

  inside1_access_in of access allowed any ip an extended list

  outside_access_in list extended access allowed object RDP3389 any host 192.168.2.10

  outside_access_in list extended access allowed object RDP3390 any host 192.168.2.11

  outside_access_in list extended access allowed object CAMERA TCP any host 192.168.2.25

  outside_access_in list extended access allowed object CAMERA UDP any host 192.168.2.25

  pager lines 24

  Enable logging

  exploitation forest-size of the buffer 10240

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  local pool RAVPN 10.1.1.129 - 10.1.1.254 255.255.255.128 IP mask

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  NAT static destination SERVER-IN-VPN SERVER-IN-VPN (indoor, outdoor) static source OWTS LAN OUT VPN OWTS-LAN-OUT-VPN

  NAT static destination of CAMERA-IN-VPN VPN-IN-CAMERA (indoor, outdoor) static source OWTS LAN OUT VPN OWTS-LAN-OUT-VPN

  NAT static destination of SERVER Virt-IN-VPN-SERVER-Virt-IN-VPN (indoor, outdoor) static source OWTS LAN OUT VPN OWTS-LAN-OUT-VPN

  !

  network of the OWTS-LAN-IN object

  NAT dynamic interface (indoor, outdoor)

  the object SERVER-IN network

  NAT (inside, outside) Shared SERVER-OUT service tcp 3389 3389

  network of the CAMERA-IN-TCP object

  NAT (inside, outside) static CAMERA-OFF 37777 37777 tcp service

  the object SERVER-Virt-IN network

  NAT (inside, outside) Shared SERVER-Virt-OUT 3390 3390 tcp service

  inside1_access_in access to the interface inside group

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 10.1.1.2 1

  Timeout xlate 03:00

  Pat-xlate timeout 0:00:30

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  Enable http server

  http 192.168.2.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP

  DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  Terminal registration

  name of the object CN = SACTSGRO

  Configure CRL

  Crypto ikev1 allow outside

  IKEv1 crypto policy 10

  authentication crack

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 20

  authentication rsa - sig

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 40

  authentication crack

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 50

  authentication rsa - sig

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  authentication crack

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 80

  authentication rsa - sig

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 100

  authentication crack

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 110

  authentication rsa - sig

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 120

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 130

  authentication crack

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 140

  authentication rsa - sig

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 150

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  Telnet 192.168.2.0 255.255.255.0 inside

  Telnet timeout 15

  SSH 192.168.2.0 255.255.255.0 inside

  SSH timeout 5

  SSH version 2

  SSH group dh-Group1-sha1 key exchange

  Console timeout 15

  dhcpd auto_config inside

  !

  a basic threat threat detection

  statistical threat detection port

  Statistical threat detection Protocol

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  username admin privilege 15 xxxxx encrypted password

  attributes of user admin name

  VPN-group-policy DfltGrpPolicy

  type tunnel-group CTSGRA remote access

  attributes global-tunnel-group CTSGRA

  address RAVPN pool

  IPSec-attributes tunnel-group CTSGRA

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  Policy-map global_policy

  class inspection_default

  inspect the icmp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:0140431e7642742a856e91246356e6a2

  : end

  Thanks for your help

  Ok

  So, basically, you set up the router so that you can directly connect to the ASA using the Cisco VPN Client. And also, the goal was ultimately only allow traffic to the LAN through the VPN Client ONLY connection.

  It seems to me to realize that you have only the following configurations of NAT

  VPN Client NAT0 / free of NAT / identity NAT

  the object of the LAN network

  Subnet 192.168.2.0 255.255.255.0

  network of the VPN-POOL object

  subnet 10.1.1.128 255.255.255.128

  NAT static destination LAN LAN (indoor, outdoor) static source VPN-VPN-POOL

  The NAT configuration above is simply to tell the ASA who don't do any type of NAT when there is traffic between the network 192.168.2.0/24 LAN and VPN 10.1.1.128/25 pool. That way if you have additional hosts on the local network that needs to be connected to, you won't have to do any form of changes to the NAT configurations for customer VPN users. You simply to allow connections in the ACL list (explained further below)

  Failure to PAT

  object-group network by DEFAULT-PAT-SOURCE

  object-network 192.168.2.0 255.255.255.0

  NAT automatic interface after (indoor, outdoor) dynamic source by DEFAULT-PAT-SOURCE

  This configuration is intended just to replace the previous rule of PAT dynamic on the SAA. I guess that your router will do the translation of the ASA "outside" IP address of the interface to the public IP address of routers and this configuration should allow normal use of the Internet from the local network.

  I suggest you remove all other NAT configurations, before adding these.

  Control of the VPN clients access to internal resources

  Also, I assume that your current VPN client is configured as full Tunnel. In other words, it will tunnel all traffic to the VPN connection, so that its assets?

  To control traffic from the VPN Client users, I would suggest that you do the following

  • Set up "no sysopt permit vpn connection"
    • This will change the ASA operation so that connections through a VPN connection NOT allowed by default in order to bypass the ACL 'outside' interface. So, after this change, you can allow connections you need in the 'outer' interface ACL.
  • Configure rules you need for connections from VPN clients to the "external" ACL interface. Although I guess they already exist as you connect there without the VPN also

  I can't say this with 100% certainty, but it seems to me that the things above, you should get to the point where you can access internal resources ONLY after when you have connected to the ASA via the connection of the VPN client. Naturally take precautions like backups of configuration if you want to major configuration changes. If you manage remotely the ASA then you also also have the ability to configure a timer on the SAA, whereupon it recharges automatically. This could help in situations where a missconfiguration breaks you management connection and you don't have another way to connect remotely. Then the ASA would simply restart after that timer missed and also restart with the original configuration (as long as you did not record anything between the two)

  Why you use a different port for the other devices RDP connection? I can understand it if its use through the Internet, but if the RDP connection would be used by the VPN Client only so I don't think that it is not necessary to manipulate the default port 3389 on the server or on the SAA.

  Also of course if there is something on the side of real server preventing these connections then these configuration changes may not help at all.

  Let me know if I understood something wrong

  -Jouni

• How to configure NAT for Hyper-V on laptop with wifi, wired and vpn connectivity

  Me, as I suspect a lot of people, I have a laptop with WiFi connection, cable connection and VPN connection (Cisco AnyConnect), which

  also uses a virtual adapter (activated when active). I searched for some time a way to be able to move to

  Hyper-V in VirtualBox. Blocker full for me is the need for a lot of my virtual machines to be able to connect to the

  Internet through 'the connection active' in the way that VirtualBox and VMWare Workstation/Player through their NAT feature.

  I'm not a networking wait, but after looking around, can't seem to find something that is simple enough for me to configure,

  with a minimum of resources, which allows me to connect a Hyper-V virtual network via a simple NAT device adapter

  all three potential network connections - most seem to not assume that one connection out of the machine, which of course does not

  me what I want.

  Three questions:

  1. is there a Windows application available that an adapter (like loopback) internal which acts as a real NAT device to one of the surfaces

  external access via the active network connections and through the Windows Firewall and any other antivirus, components etc. for

  the road to (i.e. behaves like a "normal app" inside Windows for internet access)? It would be the best option, because it would be

  "always there" when I run virtual machines

  2. display of my lack of knowledge around this feature, don't RRAS (and I know that this is not an option "minimum contact") allow you to

  Connect an internal network adapter to several external network adapters?

  3. on the Linux/OpenBSD various base/NAT routers, are everything that allow several external adapters and who are

  relatively easy to set up (by an independent expert of the network)?

  Really, we could do with this feature for Hyper-V on the desktop, but willing to work around him, if there is a way to at least the

  use virtual machines, once it is easy to install.

  Hello

  The question is more suited in the TechNet forums. So I would say you mention the link and send the request in this forum for better support.

  http://social.technet.Microsoft.com/forums/en-us/w8itpronetworking/threads

  For any information related to Windows, feel free to get back to us. We will be happy to help you.

• problem with WiFi connectivity with new Ipad Pro.  Unable to connect to the wifi at home.  My other devices (mini mac, iphone, iPad 2) all work fine on my wifi at home.  I am able to connect Ipad Pro wifi work.

  Problem with WiFi connectivity with new Ipad Pro.  Unable to connect to the wifi at home.  My other devices (mini mac, iphone, iPad 2) all work fine on my wifi at home.  I am able to connect Ipad Pro wifi work.

  On the Pro iPad, tap settings > general > reset > reset network settings

  You will need to re enter your Wi - Fi password.

  Then try to connect to your Wi - Fi network.

  If this does not help, more available in this support article suggestions > If your iPhone, iPad or iPod touch connects to a Wi-Fi network

• HP all-in - One Photoshop C6280: Scanner tring to connect with C6280 all-in - One Photoshop crashes w/task and not complete

  I had already used my scanner and it worked very well on a wireless set up.  Now, when I went to click scan again, a little box came and said, ' establish a connection with 6200.192.168.9.2 and it just hangs it and does no connection.»  I have forcibly close Microsoft fax and scan program manager tasks.   I closed my PC printer and modem wireless disconnected and reconnected since and all lit again.  My wireless phone and seems to work very well as I can get on the internet, etc., but the attempt at analysis of a new document yeilds the same results as previously with the application tries to establish a connection and just hanging there.  I used my HP scan and print doctor and everything is fine with my legacy, with the exception of the low ink level.   My drivers are up to date analysis of my HP PC.  Help, please.  What to do next?

  Hi @Zippy-4,.

  Thank you for joining the HP Forums!

  I understand that you cannot analyze with your HP Photosmart c6280 printer. I'm happy to help you in your analysis!

  To confirm that the hardware of the printer is functional, you are able to make a copy with the glass of the scanner of the printer?

  For now, try the steps in troubleshooting in this guide, Network Scanner connection is lost (Windows)and let me know what happens!

  If it helps, please consider clicking on "accept as a solution." And, please click the thumbs up icon. The two icons are below this post.

  I hope that this post helps!

• WRVS4400N with AG300 and VPN connections

  I bought a WRVS4400N router hoping to add wireless and VPN capability at a remote office LAN. I want to be able to establish a VPN connection from my PC to the central office to the WRVS4400N to remote desktop, access and administer systems at the remote office. Remote desktop systems is unnecessary access to systems to the central office.

  Before you deploy the WRVS4400N to remote desktop, I'm stable and by configuring it to our central office.

  Our central office is a router Linksys AG300 and ADSL service for Internet connection. It works well and I don't want to change it.

  I have connected the WRVS4400N to our central office LAN and it has an IP address on its WAN port assigned by the DHCP server on the AG300.

  What I do not understand how to establish a VPN connection to a system on the Internet at the WRVS4400N on the local network. I have a laptop with the QuickVPN software installed. If I connect my laptop to the AG300 (i.e. the same switch as the WAN port on the WRVS4400N) I can establish a VPN connection to the WRVS4400N but if I connect to my laptop to the Internet (via my ADSL service at home), I am unable to set up the VPN. I don't know how to configure the AG300 so that the VPN from my laptop reaches the WRVS4400N.

  I transfer ipsec enabled on the AG300, but this does not seem to run the VPN with the WRVS4400N.

  Can someone tell me what I need to do?

  Is there some other DSL modem I could use that facilitates the connection? There is another DSL modem (I don't know make/model until I visit the site) used in remote desktop, but I could replace it if I knew that the replacement work.

  Update: I got it to work. See https://supportforums.cisco.com/thread/2108785 for the advice that has been most useful.

  The essential steps have been before the ports indicated in this article (and UDP 500) to the WRVS4400N and I dropped a bit of the MTU (do not know if this was really necessary). Now I can establish connection QuickVPN, except when the Windows Firewall interferes.

  Hello

  Thank you for posting. In the AG300, transmit the following ports to the IP address of the WAN WRVS4400N port: 443, 500, 4500, 60443. This allows you to establish a QuickVPN for the WRVS4400N using the WAN IP of the AG300.

• BlackBerry Smartphones BlackBerry keeps beeping all the time - just beeps when the connection with the carrier is active.

  Gentlemen.

  I have a Curve 8900 with the 4.6.1.133 (Platform 4.2.0.85).

  This unit maintains a beep every 10 seconds, I tried to remove the battery when the BB was on, wait a minute, put it again.

  I looked at all the configurations.

  I Don t no the slightest idea and wanted to throw it in the window.

  Any ideas? Advice?

  NEW INFORMATION. The device stores only beep if the wireless connection with the carrier is active. If it s off the beeps stops. I m using Claro to the Brazil.

  Camilo

  I found the solution. This is a bug beetween the network operator's SIM card software and the BlackBerry device. It s already solved. I had to follow certain steps to enable and disable a specific feature of the network operator and wait a dialog box confirm my operation.

  The beeps comes with the dialog box, but the apears only dialog box if you are in a specific screen of the blackberry. If you are in the home screen, it will not appear and you hear the beep.

  Camilo