Remote VPN connection double

Similar Questions

• Remote VPN connected but do not go anywhere.

  within the network - ASA5505 = internet = remote VPN client.

  The ASA has a public IP address on the external interface and using PAT to the internet. He has only two interfaces, both inside and outside using the vlan. I created an IPSec VPN through CLI. My goal is for the remote client through the tunnel to through the Internet.

  Q1: Is it possible?

  Q2: the remote side is connected and has the IP address of the pool, with fact part of the network. But he can do nothing, including the gateway, which is inside the ping interface. I debug him, it shows the ASA receives the ping packets, but it is not send anything to the client. All recommend would be appreciated.

  Thank you

  Han

  Hello

  Can you please paste the result of ipconfig/all here?

  I hope this helps.

  Kind regards

  Anisha

  P.S.: Please mark this thread as answered if you feel that your query is resolved. Note the useful messages.

• Remote VPN - connect but then what? Newbie *.

  I have a 5505 and it's my first time with a unit of Cisco. My Internet works fine and my test configuration allows customers to connect properly. How do I access my network inside my remote clients?

  Hey tony,.

  So I guess that computers on your local network use 192.168.78.1 as the default gateway, and there is no path routing in pfSense router to send these back to the ASA. Please correct me if I'm wrong.

  Try to add a route on the router pfSense for the destination network 192.168.50.0/24 pointing to the inside of the interface of ASA 192.168.78.254. Let me know if it works!

  Kind regards

  Assia

• Access remote vpn connects to the 5505 but cannot ping servers

  I have a cisco 5505 and trying to set it up with 6.4 AMPS.

  My vpn client connects ok to the network but I'm unable to reach one of the servers.

  I'm sure it's a simple configuration issue, as I don't have much experience with Cisco Configuration.

  Any suggestions on where to find would be very appreciated.

  Thanks in advance

  Graham

  Hi Graham,

  Please, add the following command:

  Inside_nat0_outbound to access extended list ip 192.168.100.0 allow 255.255.255.0 192.168.100.0 255.255.255.0

  Thank you.

  Portu.

• Add a vpn connection in ios 10, method chosen in IKEv2, but I don't have the remote ID. My VPN is created in Sonicwall

  Add a vpn connection in ios 10, method chosen in IKEv2, but I don't have the remote ID. My VPN is created in Sonicwall, waiting for quick reply

  Hi cmscan,

  Thank you for using communities of Apple Support.

  I see that you add a VPN connection using IKEv2, but you do not have the remote ID. I know it's important to be able to set up a virtual private network, you can connect using your iPhone. I'm happy to help you with this.

  You must contact your system administrator to ensure that the settings that you must configure the VPN connection. Please see the iPhone user Guide for more information.

  Have a great day!

• error on the remote desktop and VPN connections

  Unable to connect using desktop remote or VPN. remotes can't find the computer at home on the network and the VPN gives me an 800 error code. I used the remote desktop, but it says my work computer isn't on this network and the VPN connection fails. We checked everything using remote assistance, but it becomes too hard and not responses. Help!!!!!!!!!!!!!!!!!!!

  Hello

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public.
  Please post your question in the TechNet Windows XP category.
  Here is the link:
  http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads
   
  I hope this helps.
  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Unable to connect to computers via Remote Desktop on the VPN connection.

  I have a Windows Server 2003 Active Directory network. Connect you to it remotely using an appliance, Sonicwall TZ170 VPN/Firewall DHCP pointing our internal DHCP server so we do not use the Sonicwall DHCP over VPN.

  The area has been recently rebuilt completely charge and the VPN connection was stronger than it has ever been when connecting to computers on our network for the first 2 weeks. In the last few days, however, people had problems connecting on our desktop computers. They can connect to some but not to others, and in the case of a person who needs in particular access to a computer, it can not connect to it all.

  I don't think it's a VPN issue but something to do with the DHCP/DNS/domain controller server. However, I am not able to locate the problem.

  In the past, this same thing was a problem before I took over. We had just a matter to the inconsistency of the connection until I thought I had solved the problem (however short-lived the fix was) with the refurbishment of the domain controller.

  Customers are a mix of Windows XP and Windows 7.

  Any ideas? I will provide all the information I can.

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  Please repost your question in the above Server Forums.

  Here is the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• Remote Desktop connection: Windows 7 Home Premium 64-bit connects to the computer of Windows XP VPN

  Hi all

  I am trying to establish remote desktop TO my new laptop (Windows 7 Home Premium 64-bit) on my computer (Windows XP) work via a VPN. The VPN Client connects to my network to work with no problems, but when I try to use the remote desktop connection I get an error message:

  Remote Desktop cannot connect to the remote computer to one of the following reasons:

  (1) remote access to the server is not enabled

  (2) the remote computer is disabled

  (3) the remote computer is not available on the network

  Make sure that the remote computer is on and connected to the network, and remote access is enabled.

  Items 1-3 are working well, so I guess that the problem is caused by another issue?
  I'd appreciate any help.
  Thank you
  Lou

  Thanks for your response Al. To answer your qus:

  (1) cisco VPN Client for 64 - bit.

  (2) I don't know how to ping through the VPN tunnel - I don't see this option, anywhere in the Cisco customer (I'm not a professional, just a user)

  (3) Yes. Also, I can connect to the host PC via my old laptop XP (xp) of fine House, just not my new laptop (Windows 7 Home Premium) so the problem must be with my new laptop rather than at the end of the host PC.

  After that you connect through the VPN tunnel open a command window, IE. go in Start > run , then type cmdand type ping DRC-hostname or IP-address-DRC ping.

  Examples:

  Ping lou - pc

  ping 192.168.1.25

  FWIW, I have a desktop computer home wireless Windows 7 Home Premium SP1 64 bit on my LAN that connects fine to a XP Pro SP3 32-bit Wired test machine using [DRC] remote desktop. Now XP Pro SP3 DRC test machine is configured for a static IP address and I have manually configured the network mask, gateway, DNS resolves and made sure that NetBIOS over TCP/IP is enabled in the properties of the NETWORK Ethernet card on the test computer.

  Just for fun, I checked the hashes of file for the file mstsc.exe on the Win 7 Home Premium 64-bit machine and a machine Win 7 Home Premium 32 bit I have and hashes were a bit different as the size of the files. The versions of the files are the same though. I assume that the difference is because we're 64-bit to 32...

• Connectivity to the remote VPN site adjacent networks

  Star topology with Corporate office which acts as hub (192.168.1.x) and remote sites connected by relay frames, except for another network (172.16.x.x) in the building served by 3560 switch company.

  On my remote site vpn (10.0.1.x) I can ping network 172.16.x.x, but not the 192.168.1.x network. What I'm trying to do is to allow the network traffic remote 10.0.1.x (which connects directly via the VPN network 172.16.x.x) to reach the network 192.168.1.x and vice versa.

  I'm sure its a combination of NAT/routing issue I forget.

  I'm new to PIX / ASA in general and it's the first vpn L2L I install. If someone can point me in the right direction, I would appreciate it.

  Thank you.

  It looks like this?

  10.0.1.x->-> Corp. ASA L2L tunnel - >->-> 192.168.1.x 3560 172.16.x.x

  and that you can currently communicate via the tunnel between 10.0 and 172.16? In order to communicate between 10.0 and 192.168.1, you will need to define this interesting traffic and add it to your crypto and nat exemption acl.

  Corp site

  extended access-list allow ip 192.168.1.0 255.255.255.0 10.0.1.0 255.255.255.0

  extended access-list allow ip 192.168.1.0 255.255.255.0 10.0.1.0 255.255.255.0

  NAT (inside) - 0 access list

  Remote site

  access-list extended ip 10.0.1.0 allow 255.255.255.0 192.168.1.0 255.255.255.0

  access-list extended ip 10.0.1.0 allow 255.255.255.0 192.168.1.0 255.255.255.0

  NAT (inside) - 0 access list

• VPN to use remote internet connection

  Hello

  I'm trying to access a Web site in the Venezuela that is blocking connections from outside Venezuela (official results of the presidential elections Sunday, which are publicly). I have access to remote control a computer running windows 7 to the Venezuela, but I don't want to use remote desktop as connections every time I want to visit this Web page.
  I remember that my school provides VPN access so that we can access documents and others during off-campus research and thought I could use VPN Windows anyway.
  I managed to create the VPN connection using VPN Windows clients/server, but it only allows me to access the internet. If I uncheck the option 'use remote gateway', while my local internet connection will always be recognized as outside the Venezuela. How can I activate the remote computer access to the internet for my local system connected VPN?

  Hello

  The Microsoft Answers community focuses on the context of use. Please join the professional community of COMPUTING in the TechNet forum below

  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

• Try to connect to a remote VPN server

  This task was bleeding in my eyes. I can't make it work. I understand the principle of TCP-OUT ACCORD - IN but can't seem to reconcile it kind includes the firewall.

  Long and short of the situation:

  Company a static IP address assigned by the local society of DSL

  All computers inside network enjoy outdoor internet access and interconnectivity

  Remote VPN host has static IP

  Configuration VPN of a properly established and the remote control accounts are active.

  Does not connect when good ID and PASSWORD are entered.

  Anyone tried this before. Please assume that I have the skill level of a child of 5 years and the patience of the same thing.

  Thank you for your help.

  Timothy S. Murray

  A child under 5 huh? looks like a lot of people that I care. I'm kidding anyone, not me flame.

  In any case, we need a little more information here to go, it's a connection to a PIX PPTP you talk, or a router? Or is it IPSec (you mentioned GRE, that's why I think you speak of free WILL). Is the user authentication is done locally on the endpoint VPN device, or is it a server Radius/GANYMEDE involved?

  Can you send in the configuration of the end device, ensuring xxxxx valid IP addresses and passwords?

• die remote desktop during the VPN connection

  I by office remote access to a server that is connected by the Cisco VPN client to other servers, but when I connect the VPN, the sector of remote desktop, if I have this connection loose and cannot work.

  That's what I should do, but when the VPN connects, my remote desktop connection matrix:

  |***|                                    |***|                     |***|

  |__|  --> Remote Desktop--> | __ |   --> VPN --> |__|

  me server1 server2

  I can't VPN to server2 directly, I have to go through Server1, but I can't.

  Javier,

  When VPN appears on server1, then all traffic get dug in the client [including the remote desktop session].

  ===> You need a split-mining policy which aims to exclude the IP address of your customer

  See you soon,.

• Unable to connect to remote vpn IPSec (Error 412)

  Hello

  Try to configure the IPSec vpn connection but error 412: the remote peer not responding.

  Router Cisco is directly connected to the internet using the dialer interface.

  So far, I tried the following:

  Disabled Windows Firewall

  IPSec over TCP ticket (received error 414)

  Permit to debug crypto ISAKMP and IPSEC (no illustrated newspaper)

  Newspapers enabled on the version of client VPN 5.0.01.0440

  (Impossible to establish Phase 1 SA with server 'xxxxxxxxx' due to the 'DEL_REASON_PEER_NOT_RESPONDING')

  The router configuration:

  version 12.4

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  encryption password service

  !

  !

  boot-start-marker

  boot-end-marker

  !

  !

  AAA new-model

  !

  !

  AAA authentication login default local

  AAA authentication login usr_auth local

  AAA authorization grp_auth LAN

  !

  AAA - the id of the joint session

  !

  resources policy

  !

  MMI-60 polling interval

  No mmi self-configuring

  No pvc mmi

  MMI snmp-timeout 180

  IP subnet zero

  no ip source route

  IP cef

  !

  !

  No dhcp use connected vrf ip

  DHCP excluded-address IP 192.168.3.1 192.168.3.10

  !

  pool IP dhcp pool Classes

  network 192.168.3.0 255.255.255.0

  default router 192.168.3.1

  Server DNS XXXXXX xxxxxxxxxxx

  !

  !

  no ip bootp Server

  no ip domain search

  IP domain name xxxxxxxxx

  property intellectual ssh time 80

  VPDN enable

  !

  !

  !

  !

  !

  username 7 password xxxxxx xxxxx

  !

  !

  !

  crypto ISAKMP policy 10

  BA aes

  preshared authentication

  Group 5

  !

  ISAKMP crypto client configuration group client_cfg

  XXXXXXX key

  DNS xxxxxxx

  pool vpn_pool

  ACL 120

  Max-users 2

  Profile of isakmp crypto vpn-ike-profile-1

  client_cfg group identity match

  client authentication list usr_auth

  ISAKMP authorization list grp_auth

  client configuration address respond

  virtual-model 2

  !

  !

  Crypto ipsec transform-set encrypt-method-1 esp - aes esp-sha-hmac

  !

  Crypto ipsec VPN-profile-1 profile

  the transform-set encrypt-method-1 value

  !

  !

  !

  !

  interface Loopback0

  the IP 10.0.0.1 255.255.255.0

  !

  ATM0 interface

  no ip address

  No atm ilmi-keepalive

  DSL-automatic operation mode

  !

  point-to-point interface ATM0.1

  no link-status of snmp trap

  PVC 8/35

  PPPoE-client dial-pool-number 1

  !

  !

  interface FastEthernet0

  no ip address

  automatic speed

  !

  interface FastEthernet1

  Shutdown

  !

  interface FastEthernet2

  switchport access vlan 2

  !

  interface FastEthernet3

  switchport access vlan 3

  !

  interface FastEthernet4

  switchport access vlan 4

  half duplex

  !

  tunnel type of interface virtual-Template2

  IP unnumbered Loopback0

  IP nat inside

  IP virtual-reassembly

  ipv4 ipsec tunnel mode

  Profile of tunnel ipsec VPN-profile-1 protection

  !

  interface Vlan1

  no ip address

  !

  interface Vlan2

  192.168.1.100 IP address 255.255.255.0

  IP nat inside

  IP virtual-reassembly

  IP tcp adjust-mss 1452

  !

  interface Vlan3

  address 192.168.3.1 IP 255.255.255.0

  IP access-group 101 in

  IP nat inside

  IP virtual-reassembly

  IP tcp adjust-mss 1452

  !

  interface Vlan4

  192.168.4.1 IP address 255.255.255.0

  IP nat inside

  IP virtual-reassembly

  IP tcp adjust-mss 1452

  !

  interface Dialer1

  the negotiated IP address

  IP mtu 1492

  NAT outside IP

  IP virtual-reassembly

  encapsulation ppp

  Dialer pool 1

  Dialer-Group 1

  PPP authentication pap callin

  PPP pap sent-name of user password xxxxxx xxxxxxx 7

  !

  local pool 10.0.0.10 IP vpn_pool 10.0.0.20

  IP classless

  IP route 0.0.0.0 0.0.0.0 Dialer1

  !

  no ip address of the http server

  no ip http secure server

  the IP nat inside source 1 list overload of the Dialer1 interface

  IP nat inside source static tcp 192.168.1.1 25 25 Dialer1 interface

  IP nat inside source static tcp 192.168.1.1 80 80 Dialer1 interface

  IP nat inside source static udp 192.168.1.1 53 53 Dialer1 interface

  IP nat inside source static tcp 192.168.1.1 53 53 Dialer1 interface

  IP nat inside source static tcp 192.168.1.1 interface 1000 Dialer1 1000

  IP nat inside source static tcp 192.168.1.1 interface 443 443 Dialer1

  IP nat inside source static tcp 192.168.1.1 interface Dialer1 143 143

  !

  WAN-IN extended IP access list

  refuse the ip 0.0.0.0 0.255.255.255 everything

  deny ip 10.0.0.0 0.255.255.255 everything

  deny ip 100.64.0.0 0.63.255.255 all

  deny ip 127.0.0.0 0.255.255.255 everything

  deny ip 169.254.0.0 0.0.255.255 everything

  deny ip 172.16.0.0 0.15.255.255 all

  deny ip 192.0.0.0 0.0.0.255 any

  deny ip 192.0.2.0 0.0.0.255 any

  deny ip 192.168.0.0 0.0.255.255 everything

  deny ip 198.18.0.0 0.1.255.255 all

  deny ip 198.51.100.0 0.0.0.255 any

  deny ip 203.0.113.0 0.0.0.255 any

  refuse the 224.0.0.0 ip 31.255.255.255 all

  allow an ip

  !

  access-list 1 permit 192.168.1.0 0.0.0.255

  access-list 1 permit 192.168.3.0 0.0.0.255

  access-list 1 permit 192.168.4.0 0.0.0.255

  access-list 101 deny ip 192.168.3.0 0.0.0.255 192.168.1.0 0.0.0.255

  access list 101 ip allow a whole

  access ip-list 120 allow a whole

  !

  control plan

  !

  !

  Line con 0

  exec-timeout 5 0

  line to 0

  exec-timeout 5 0

  password 7 xxxxxxxxxxxx

  line vty 0 4

  exec-timeout 5 0

  password 7 xxxxxxxxxxxx

  preferred transport ssh

  entry ssh transport

  line vty 5 15

  exec-timeout 5 0

  password 7 xxxxxxxxxxxx

  preferred transport ssh

  entry ssh transport

  !

  end

  I don't get any password prompt, so I guess there is a misconfiguration. Would appreciate if you can help with this.

  Thank you

  The 10.0.0.x pool is configured properly. Just change the NAT to traffic between 192.168.1.x, 3.x, and 4.x are exempt in NAT, where the above change config.

  Your split tunnel ACL says allow an entire ip, so please change it to the following:

  access-list 120 allow ip 192.168.1.0 0.0.0.255 10.0.0.0 0.0.0.255

  access-list 120 allow ip 192.168.3.0 0.0.0.255 10.0.0.0 0.0.0.255

  access-list 120 allow ip 192.168.4.0 0.0.0.255 10.0.0.0 0.0.0.255

• active monitoring of remote access vpn connections

  Hi all

  I use asa 5520, and asa 5540 for remote access vpn connections. Is it possible to active my vpn connections monitoring so that there would be alerts for vpn tunnels which fail to implement for other reasons other than the authentication of users? Pls advise. Thks in advance.

  Kiwi Syslog will work fine - as long as you have a licensed version, a 'free' version does not support e-mail extras.

  See the url below and search for "VPN", you will see what VPN syslog codes you can choose from.

  http://www.Cisco.com/en/us/docs/security/ASA/asa83/system/message/logmsgs.html

  HTH >

• ASA 5505 ASDM VPN connection problem

  Hello

  We are running a version of firewall ASA 5505 8.4 (4) 1. The ASDM version is 6.4 (9).

  The problem is when the creation of remote access VPN connection, it works fine for about 2-3 days.

  After that, the VPN client cannot connect more and gives the error code 789.

  In this case, the VPN clients are clients of Windows 7 from different remote networks with the same problem scenario.

  Windows 8.1 clients cannot connect at all and show the same error code...

  All connections go through the keys defaultragroup and preshare match on both sides.

  When the user to connect attemps I receive the following text in the log of the ASDM:

  6 April 10, 2015 10:52:39 group = DefaultL2LGroup, IP = 5.240.31.116, P1 retransmit msg sent to the WSF MM
   
  5 April 10, 2015 10:52:39 group = DefaultL2LGroup, IP = 5.240.31.116, in double Phase 1 detected package.  Retransmit the last packet.
   
  5 April 10, 2015 10:53:03 IP = 5.240.31.116, encrypted packet received with any HIS correspondent, drop
   
  When I implemented the remote login through ASDM I followed the instructions according to the following link:
  http://www.databasemart.com/HOWTO/Cisco_VPN_Remote_Access_Setup_ASA5500...
   
  The steps were a little different, but almost the same, given that these instructions show an old version
   
  I'm interested in trying the steps according to this link but not sure this will help me solve the problem id:
  http://www.petenetlive.com/kb/article/0000571.htm
   
  Any help would be appreciated!
  Thank you

  Hello

  If you use local authentication (user name and password on the SAA), so why you would need this threshold?

  tunnel-group DefaultRAGroup ppp-attributes
  No chap authentication
  ms-chap-v2 authentication
  !

  Remove it and try.