All share storage iscsi connect same target and volume

Similar Questions

• Now, all the applications on my Mac air show the same icon and doesn't open, please help!

  I did a quick cleaning on my Mac and now all my applications show the same icon and does not open! TIA :-)

  "quick clean up"...

  It seems that you may have removed some system files, you shouldn't have.

  If your Mac is running v10.7 Lion or later, you can restore OS X using OS X Recovery.

• ISCSI connection failure causing ESXi 5.1 VMs at the stop

  Hi all

  At the hope that someone may have seen the problem that we encountered during the last 2 weeks.

  Our virtual machines are performing unexpected stops. Our Exchange Server rebooted twice today

  The closing time is information that we see our Equallogic logs:

  INFO APCEQLM1 09:35:19 7.2.15 26/07/2013. 7.2.24 | 7.2.29 session iSCSI to target '192.168.43.12:3260, iqn.2001-05.com.equallogic:4-52aed6-c7ca4349e-87b00217be35059e-lon-prod-vm-1' initiator ' 192.168.43.31:58797, iqn.1998 - 01.com.vmware:apcesxhost1 - 24c73c18 "was closed. | iSCSI initiator login failure. | No response on the connection for 6 seconds.

  We have 1 Equallogic PS4100X, run the latest firmware EQL 6.0.5. We have 2 switches Powerconnect 6224 stacked. Our table and switches are configured by DELL support.

  We followed the recommendations of DELL on vSphere storage ISCSI connection. I see that our vSwitches are correctly configured.

  Someone has any ideas why we find that this behavior? I have connected this with the support of DELL, but thought I would ask on the forums in case someone knows that it emits.

  Thanks in advance!

  Lee

  Hi Julie,.

  My apologies, I thought that I had updated this discussion with the fix. It was related to a problem of driver on one of our hosts. I logged a call with VMWare and they got the answer very quickly. The problem was our host NETWORK interface card tg3 driver. I've followed this article to resolve the problem:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=2035701

  I hope it is of some use to you!

  Thank you

  Lee

• My screen keeps freezing same mouse and I have to close my computer and start in safe mode

  Original title: screen freezing same mouse helps getting more frequent

  Hi all my screen keeps freezing same mouse and I have to close my computer and start in safe mode, I have windows vista. its most frequent doing, I tried to look at the error logs and so on, told it could be my macfee product and another said it was critical error id 400? I'm quite beyond my depth, I did scan virus and his watch not that I have nothing. Please help, I am a real novice so please explain as easy as you can, thank you very much

  Ensure that your data is backed up / copied to external media. It seems that your PC has a hardware problem. If it's a name brand PC, for example Dell / HP etc it may have preinstalled utility test read the manual or manufacturer's web site

  If it's a generic PC, then your machine to HD will have a free test bootable utility, for example SeaTools from Seagate

  To test the memory, www.memtest.org

• Edge Animate: Detect if the 5 elements are dropped on their targets and display a message "Bravo."

  I was hopgin this would be pretty simple, but must still find a way to do it, or a tutorial that covers online.

  I initially followed the tutorial video of Paul Trani for drag / drop objects on a target, which is really userful, ()Drag and Drop in edge animate part 2: Multiple with Touch - YouTube)

  Now, I want to add code to detect the moment where all points are interrupted on their targets, and then show a simple "well done" text or graphics. That I had a post on StackOverFlow for about a year now without a valid answer.

  Thanks Resdesign, it is more useful

• Differences between the ISCSI connections to the storage in vSphere 4.1 and 5.0.

  I'm in trouble of setting up the connections of storage in a new VSphere 5.0 test environment. In our environment VSphere 4.1, it was possible to create a virtual switch add two Broadcom NetXtreme II 5709 NIC. Set assets. IP Hash value as load balancing. (LACP Etherchannel on physical switches) This configuration uses a grain port and a single IP address. Then add our NetApp NFS storage and ISCSI Equillogic storage. In VSphere 5.0, I can't create this same configuration. I have to create separate with separate IP addresses vmkernal ports? The idea was to have redundant connections to the storage and flow of these two NETWORK cards. Possibly adding additional if necessary to the futuer NETWORK cards. Any help with this would be greatly appreciated.

  How can I work around this:

  "VMkernel network adapter must have an active link exactly and no waiting rising to be eligible for the iSCSI HBA connection."

  I can certainly say that the way which allows you to configure the iSCSI Multipathing is incorrect.

  The main idea is to let Native Multipathing Plugin to decide what network path to choose, not the vSwitch.

  At the level of the network layer, you must have 1 VMK by a physical NIC.

  This technique applies as well for vSphere 4.1 and 5.0, but with the 5.0 it is configured easier and more quickly.

  Here's a very brief consequence of steps

  1. get 2 VMK interfaces and assign an IP by each VMK.

  2. set each VMK to use only one physical NETWORK adapter

  3 GB with storage iSCSI software adapter, turn it on and bind your VMKs 2.

  4 connect to your iSCSI storage space

  5 rescan devices, create the VMFS datastore

  6. set the desired load balancing VMFS method or just set up a prior default create new VMFS

  and it is strongly recommended to read this guide - http://pubs.vmware.com/vsphere-50/topic/com.vmware.ICbase/PDF/vsphere-esxi-vcenter-server-50-storage-guide.pdf

• I teach online and all my classes have the same user name and password. Now that I clicked "remember me next time", I can connect only in one class. How to unlock my password. Carol in English

  I teach online and all my classes have the same user name and password. Now that I clicked "remember me next time", I can connect only in ONE class. How to unlock my login and my password, so that I can use it for all classes. Carol in English

  "Remember Me" for the site connections automatically when you return to the Web site is done with a Cookie the site in Firefox.

  Try to clear your Cookies for this Web site.
  
  Tools > Options-> life privacy - Cookies = the button show Cookies.
  
  You must use the custom settings for history at the top of this tab to see the View the Cookies button.

  Enter the domain name in the top search bar and all Cookies for this URL will be displayed. Unless you can figure out which is Cookie to "remember me", you will need to delete them all.

  Hold the {Ctrl} key while you click each Cookie in the small window. When this list is all highlighted, click the Cookie delete button at the bottom left.
  When you are finished click Close.

• groups and iSCSI connections to ports

  Hello

  We have a 5.1 esx server connected to an iSCSI-based storage device.

  the server is connected using two of the vmkernal iscsi ports.  each network card has a different ip address on the private iscsi vlan.  the configuration is according to the practices of bast vm using only one network by vmkernal port card.

  We have a migration of storage to another storage but I still have to intall it.  I would like to know if its possible to create two groups of ports additional vmkernal using the same NIC already connected to the iscsi storage.  new port groups on one vlan separate and different netwok so go looking, it seems right that I share two NICs for two networks different iscsi.

  as mentioned above, that I have not installed the hardware yet, but to test it a bit it looks like I can add groups of ports by using the network card and I was able to bind to the vmhbaxx with the adapter of storage with the path of staus as not used.  so I hope that when I connect the new buffer I would be if all goes well able to connect once I place a discovery?

  any comments welcome.

  Thank you

  I don't see why you shouldn't be able to do what you describe. It's a little unusual, but it should work to create adapters to VMK several on the same vSwitch and make the same active/unused configuration you already made, but put other id VLAN and IP address on the new adapters. Of course the two logical VMK adapters share the same network link, but you are fully aware of.

  As long as it is not indicated in some manual or KB article as a solution not supported, you should be fine.

• With the help of a PIX501 to secure and share an internet connection by cable

  Hi all

  I bought a PIX501 to secure my home cable modem connection and share it around my house. The PIX will act as a DHCP client (my ISP uses dynamic IP addressing) and use nat and DHCP break with my small number of inside customers.

  The default setting (set using the set up of PIX) seems ok - but I did a little "do-it-yourself" after some negative PIX customers I've read here in the United Kingdom.

  Specifically, I: -.

  -A refused requests incoming icmp (to make the "invisible" PIX to the outside world)

  -Created an access list to allow answers to my outgoing ping (something every geek network must be able to do)

  -The value "string fragment 1 outside" to drop incoming fragmented packets

  -Limit the number of connections to 200 and embroyonic at 50

  -Activated floodguard (although I don't think this should be necessary on such a lightly loaded network)

  -Compatible console logging so I have at least a bit of history of all attacks

  -Reduced some of the delays of the connection of their default values

  As I have a relatively new to this kind of thing anyone have specific advice or tips for a pix used this way?

  Thanks in advance,

  Andrew.

  When you work with ICMP, remember that [icmp] command to assign ICMP messages for the pix as the host, while the [access-list] command is used to assign ICMP messages that pass through the Pix.

  If you are using IPSec tunnels through the Pix, you can consider letting in string fragment of 2 sizes. IPSec creates broad enough to cause a lot of packets to be fragmented. Path MTU discovery would prevent, but many networks prevent incoming requests that allow the discovery to work. For this same reason, you can also consider allowing the Pix to get unreachable inside your host name if you the Pix end VPN tunnels. [icmp outside any unreachable towing]

  Floodguard is enabled by default and does not need to be enabled. It should not be necessary on a little loaded network, but it would be necessary at the time of a DoS attack if you are Pix does authentication "uauth" of traffic entering or leaving the network.

  If you are interested, the Pix can authenticate users inside before allowing the traffic leaving using RADIUS. This is useful in situations like a web server inside is attacked from outside. By the application of authentication for other traffic to leave for offending guests options are very limited. A timeout is used to trigger authentication again after some time. The [floodguard] is used to protect this feature "uauth' of the Pix.

  The Pix has signatures VERY BASIC integrated IDS that you can activate by using the set of commands [assessment of intellectual property].

  Enable SSH for authentication and encryption by generating an RSA key and saving it to Flash. [AC product key 1024 rsa] and [ca save all] disable telnet by removing all orders [telnet] and replace them with [ssh]. [http] should also be limited as much as possible for the administration.

• All the sites SSL Web I visit displays the message "this connection is untrusted" and shows me a false SSL certificate for a different domain name.

  When I visit a Web site that requires SSL I displays the message "this connection is untrusted". Any Web site that I visit, it's always exactly the same message and the same SSL certificate that she is no longer valid for www.thawte.com

  support.Mozilla.org uses an invalid security certificate.

  The certificate is not approved, because no sender string has been provided.
  The certificate is valid for www.thawte.com
  The certificate expired on 11/11/2011 23:59. The time now is 11:46 28/01/2012.

  When I click "Add the Exception" on a Web site and view the certificate, it is exactly the same certificate with the exact same serial number.

  I had a similar problem with Internet Explorer showing a 404 error when I visited SSL protected pages but to do a restore of the system a month ago to correct this. All other bowsers are / were very good.

  I installed Firefox 3.x month last to test something that is when the problem started. I have since uninstalled Firefox 3.x and reinstalled the latest version. I deleted all the preferences/settings, disabled modules and reinstalled many times. I did a Windows system restore to before that the problem started with no luck.

  The time / Date on my computer are correct. I have no firewall other than the windows one. I had no antivirus (netbook) until I installed a (Avast) yesterday to see if a virus was causing issues (found nothing). This problem arises on any internet connection (tested to work and home).

  Try bypassing the caveat

  or try to use the module Skip Cert error (to jump to the SSL/TLS certificate error page)

  Thank you

  Please check 'Resolved' the answer really solve the problem, to help others with a similar problem.

• HP all-in - One Photoshop C6280: Scanner tring to connect with C6280 all-in - One Photoshop crashes w/task and not complete

  I had already used my scanner and it worked very well on a wireless set up.  Now, when I went to click scan again, a little box came and said, ' establish a connection with 6200.192.168.9.2 and it just hangs it and does no connection.»  I have forcibly close Microsoft fax and scan program manager tasks.   I closed my PC printer and modem wireless disconnected and reconnected since and all lit again.  My wireless phone and seems to work very well as I can get on the internet, etc., but the attempt at analysis of a new document yeilds the same results as previously with the application tries to establish a connection and just hanging there.  I used my HP scan and print doctor and everything is fine with my legacy, with the exception of the low ink level.   My drivers are up to date analysis of my HP PC.  Help, please.  What to do next?

  Hi @Zippy-4,.

  Thank you for joining the HP Forums!

  I understand that you cannot analyze with your HP Photosmart c6280 printer. I'm happy to help you in your analysis!

  To confirm that the hardware of the printer is functional, you are able to make a copy with the glass of the scanner of the printer?

  For now, try the steps in troubleshooting in this guide, Network Scanner connection is lost (Windows)and let me know what happens!

  If it helps, please consider clicking on "accept as a solution." And, please click the thumbs up icon. The two icons are below this post.

  I hope that this post helps!

• How to share an internet connection Wi - Fi, which requires the user name and password on a laptop computer of Windows 8 on a PC with Windows XP?

  I have Windows 8 on my laptop... and this laptop is connected to the internet via an USB-powered Wifi device, it takes an user name and password to connect to the internet otherwise it says limited connectivity and will not connect to internet... now, I have an old PC with Windows XP on it... the PC and laptop have built in LAN cards... I also have a cable that fits in the LAN cards... when I connect the two computers, LAN cards and Windows flashlights, they also show that they are connected to a local network... However, I can't use this Wifi connection on my laptop to share an internet connection with PC WIndows XP... I tried to fill, manually configure IP addresses, sharing connections, all with no luck... of many websites is a lot of confusion...: /... Please someone guide me step by step how can I make my XP PC to connect to the internet using the connection of the laptop...

  Hello Ashan,

  Thanks for the reply.

  You can try to follow the following suggestions to solve the problem.

  First, try to reset Internet Explorer and see if that helps.

  Reset Internet Explorer

  http://support.Microsoft.com/kb/923737

  Note: The Reset Internet Explorer Settings feature might reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings. Reset Internet Explorer is not reversible, and all the previous settings are lost after reset.

  Additional information:

  We can also refer to the computer or the device manufacturer's Web site and try to update the latest version of the network adapter drivers.

  (Also works for Windows 8)

  Updated a hardware driver that is not working properly

  To connect to the Internet

  http://Windows.Microsoft.com/en-us/Windows/Connect-Internet#1TC=Windows-8

  I hope this helps. Otherwise, feel free to write us again and we will be happy to help you.

  Thank you

• The backup of Duplication without a target and recovery catalog connection-oriented

  Hello
  We need restore a database - it's now my idea of using replication backup without a target and recovery catalog connection-oriented (I don't want to disturb the source database and we do not use a recovery catalog).
  Backups are stored on tapes (by Omniback from HP).
  
  The syntax should be like this:
  
  duplicated to dup_db database
  until ' to_date (May 2, 2012 02:00, ' ' the HH24: MI: SS DD/MM/YYYY).
  SPFile
  location of backup '?
  nofilenamecheck;
  
  We must use the backup from May 2, 2012 - so it's my understanding that we need to use the clause "until" to_date (May 2, 2012 02:00, ' ' JJ/MM/AAAA HH24:MI:SS) "."
  
  But because the backup is located on the Strip I do not know the value of "backup location. I thought that the name of Omniback backup could be used, but that has not worked.
  
  Now my questions are:
  -is it possible to restore a database as shown with the option-double?
  - and does the job "until" in this case?
  
  Any help will be appreciated.
  
  Rgds
  JH

  Hello

  Unfortunately, you forgot to say which version of the database, it has a double option without a recovery catalog and without connection to the main DB was introduced with 11.2 (if 11.2.0.2).

  And as you can see here:

  http://docs.Oracle.com/CD/E11882_01/backup.112/e10642/rcmdupdb.htm

  you need a backup of disk based to use it.

  "A location of disk backup that contains all backups or copies for reproduction must be available for the destination host".

  Concerning
  Sebastian

• Is it possible to use iCloud shares photos with the two opening and Photos at the same time?

  Is it possible to use iCloud shares photos with the two opening and Photos at the same time?

  Non - PEAK is not a feature of iPhoto or Aperture - this is new with Photos

  LN

• Clocks additional all tell the same time and I can't change the time at all

  I need to understand how the clock on my computer application construction. There additional clocks that are all about the same time as mine and it does not give me any other time zone applied to them. How to fix this? It is said for the moment available only box is there a fix Ulaanbaatar.

  OK did it... now what?

  Back to additional clocks. See all changes if you click on this pointer.

  If nothing changes, then read this tutorial. It's verification options from drives that are designed to right the wrongs of your disks. Read it all first, particularly two method, step 3 and 4, with regard to changes in the disk check.
  When finished I wrapped up ready, start with a method.
  Remember, you will need to restart in order to start the disk check.

  t-4-2