All those put up the SPI bus on a 7831R using Labview 2009? I have

Similar Questions

• How can I display the time of the data stored in a file using labview?

  How can I display the time of the data stored in a file using labview?

  Hi Matt,

  I think that we will need a little more information as to how you capture the data, what data you capture, etc.

  If you capture a waveform, is to extract the time data waveform which includes the t0 and dt values, so you can understand the time stamp of a specific data point as in the image below.

• convert elements using the DAQCard-6024E card to USB-6221using LabVIEW 2009

  I just got an old project, the VI has been primarily designed using the DAQCard-6024E map. Since we would be upgrading the equipment and the DAQCard-6024E serves not long. However, they want to keep the similar façade. I am trying to convert the drop-down menu that I can use with USB-6221 with Windows 7, but I don't know how. Can anyone help?

  Windows 7, NI USB-6221, LabVIEW 2009 sp1

  Hi smoothenigne007,

  After watching your upgrade.  All your writing VI should use the same task.  There is no need to close this task until the end of the program.  In addition, you can remove all the time because they do not allow the task close a loop.  I did a performance highlighted with your code and you can see that the first task was not allowed at the time wherever the data reached the second task.  When you try to create the second task, the error is generated.  Because you do not give me multiple writes to the same port there is no need to open and close the task each time.  Here is a link that will explain a little more about the DAQmx driver works.

  Getting Started With DAQ

  Kind regards

• Impossible to find the field read and write VI in labview 2009

  where is the field point to read and write VI in labview 2009

  According to the version of LV, BT pallets can be sensitive to the context. Try to create a project and add a fieldpoint target to the project.  Right-click on the target of FP in your project and select new > vi.  Now FP functions should appear

• All those put in place of boxes instead of Yes No?

  I tried to play with the appache configuration files and was able to do that the boxes appear instead of Yes, but they did not work as they should.
  
  Can someone give me a specific example of how they have implemented it determinations of Web?

  The problem is that the check boxes present all values if they are unchecked. The best way to do what you want would be to render the control as an input hidden; make a separate control to display check boxes; and then use JavaScript to set the value of the hidden control to true or false depending on the State of the checkbox.

• Keep all information collection during the acquisition of images when you use the basic IMAQ package

  I did show a command of X from IMAQ image control that has the ability to overlay dots and lines on an image, but when I put my control of X in my loop of acquiring image collections information disappears with each new picture that I acquire.

  How can I keep the overlay in place and just update the control with the new image and does not overwrite data overlay? I tried the function of superimposition of fusion, but this doesn't seem to work.

  Thank you.

  Overlays are completely erased when you acquire a new image.  You can create collections on a separate image, and then copy to each new image overlays until you view it.  The other option is to re-create overlays for each new image.

  Bruce

• Helps the acquisition of photon counter data using LabView 12

  Hey all,.

  Student graduate Chemistry here new to LabView and are looking for some help moving in the right direction.  I'm looking for help with connecting my meter to 12 LabView for data acquisition of trace-fluorescence photon PerkinElmer SPCM-AQR-14 (now owned by Excelitas Technologies).  I just want to be able to acquire number of photon counts vs. time.  Currently, I installed a PCI-6601 and use a BNC-2121 to connect the BNC of the sensor output.  The detector has a pulse output digital TTL with 30 ns pulse width, and by contacting technical support on this issue, I was told that this pulse width was too short to always detected by the 6601, but can still go ahead and give it a try.  Basically, if everyone is familiar with how to start with this configuration, ANY help would be greatly appreciated.  As I said I'm all new to LabView and am currently spend all my spare time reading manuals and help files.

  Please let me know if you need any kind of information to make me understand what I'm doing.

  I would say something like this:

  

  A measurement period the registry account out of the entrance of the samples as well as gives the meter.  You will basically measure the 'period' of your sample clock fixed regarding ticks of the external photon signal.

  According to the downtime, you may need to re-read several samples per loop so that the software can keep up with the incoming data.  Also, the first sample is not useful because it represents the County between the software from the task of entry of the meter and the first clock signal - you should disregard/erase the first sample (or if you want you can set up a trigger to begin arms).

  To do the same thing by using an edge County task would require using both the sample clock AND a counter reset signal - this not is not supported on 6601/6602 (even if it would be possible to set it up that way on a device of STC - 3 as a series of X).

  Best regards

• How to open the sounds and audio properties by using Labview

  Hi all

  How to open the sounds and audio properties of the control panel using the exe from system Labview vi.

  Y at - it all dll also open this property.

  If there is some dll which is which and how to program the dll to achieve my goal.

  Wow, you followed after a few...

  Open the command window is because to open the Control Panel, you need to execute it in the context of a shell, and it's what is done with the "cmd /c mmsys.cpl. To open the applet without using cmd you use RunDll32.exe, like this:

  

• Determine the number of traditional DAQ hardware using Labview.

  Hello

  Anyone can answer the question:

  Regarding materials traditional DAQ, for example the DMM OR-4060, how

  can I programmatically determine the number of device which can be seen in MAX?

  With the help of Labview 8.5, I looked into the following function libraries:

  NOR-DMM

  VISA

  NOR-ModInst

  None of the libraries above seem to provide access the number of traditional DAQ hardware

  property, which is automatically assigned.

  Background:

  I have a 18 PXI chassis containing 2 DMM, in housing 3 and 14.

  The DMM may be a mixture of type OR-4060 or NOR-4070.

  The system is controlled by a Teststand sequence employing IVI - DMM

  steps.

  When you set the IVI logical name step, I am referring to IVI device defined Sessions

  Max - rutime determined.

  Labview VISA functions using I can determine the model, i.e. 4060 or 4070.

  Because the DMM just locate into the slots 3 or 14, then the devices NOR-4070

  are accessible using the following descriptors of resources: PXI1Slot3 or

  PXISlot14.

  (The 4070 is compatible DAQmX.)

  So for devices OR-4070, I can predefine 2 Sessions of IVI device, knowing

  It will be sufficient for all occasions, when I run my Teststand sequence, which will be

  determine what device session to use at run time.

  But I'm stuck for the NOR-4060.

  At the Session of the device, I have to give a descriptor of resource the following

  format: DAQ::x (where x is the device number)

  I could create device 18 sessions each reference to a different DAQ::x, but to select

  the good pair during execution, I would need to programmatically determine the device

  number, i.e. the value of x.

  Where my question.

  The closest I came to a solution was an entry of the Knowledge Base that said that the

  Assigned device number would be the same as the slot number, providing the

  Number of the device had not previously configured manually.

  Unfortunately, our device numbers have been changed manually and maybe in the future.

  All popular solutions.

  Gary.

  Hi Gary,.

  Good afternoon and I hope that your well today.

  Thanks for your post and I want to help you solve your problems.

  I don't think there is just a function that you can use to identify and collect information on all cards with your. For traditional DAQ devices in particular I suggest using the Information.vi of DAQ devices get.

  If you look at this link,

  SAL posted an example VI entitled, find dev trad.vi.

  You can get information such as serial number, Dev name and the Base address.

  The assistance of the respective drivers to collect information you could generate an array of strings with the information that you need all the slots.

  Please let me know if this is useful at all,

• the time display of the data stored in a file using Labview

  I saved data in an Excel file but I donnot know how to display the time recorded for each data. I would be grateful if you can help me.

  Thank you very much

  Sincerely,

  Nehemia Elvis

  Hi Matt,

  where do you have problems? You have already saved time and you only write in the file?

  Mike

• Narrow ARM of SPI VI reference works do not for me LabVIEW 2009.

  I use LabVIEW 2009 Embedded for ARM in collaboration with the Council of development of LM3S8962 and the MCP3008 10 - bit ADC chip. I'm trying to use the base screws of SPI to communicate with the MCP3008 - see the attached excerpt from VI to my current attempt. I can initialize the SPI reference, read two bytes of data from the ADC, but when I try to close the reference, the application crashes. If I am the narrow ARM of SPI reference VI in a diagram to disable, the program terminates normally, and I get to see my two bytes of data printed on the OLED. Any ideas?

  Thanks in advance,

  Stuart

  Thank you!

  Who takes care of the immediate problem. I really appreciated the quick response!

  Stuart

• to detect if the USB is connected or not in labview

  I want to detect if the USB is connected or not using labview

  Hello

  A simple method you can use to list out the folders on your computer.

  If no key USB is connected to your computer, you will get the name of pen drive.

  First download all the number of readers. Constant than this value if the next time with your USB drive, you get the number of elements is longer then one fixed, then you can say external peripheral is connected with the PC.

  

  Maybe this is not the standard method to detect the device, but it may solve your problem.

  Thanks and greetings

  Himanshu Goyal

• Close the HyperTerminal Application using LabVIEW

  I have a client who wants to LabVIEW to close the HyperTerminal Application automatically is the serial port open.

  It is easy to detect that the serial port is already in use.  I already have a popup that tells the operator to close any application communication because the port is already in use; However, they want to do it automatically.

  HyperTerminal is not taken support ActiveX, and they will not go to the version more professional who does.

  For a long time, I had read a thread where it was possible to close (or open)? and demand having no ActiveX support.  I expect to use similar approach...  Opening the app is simple, but closure is another story.  You need some sort of reference to this request to tell Windows that are to close.  The Win - XP operating system.

  Suggestions are welcome.

  R

  http://www.howtogeek.com/HOWTO/Windows/kill-processes-from-the-Windows-command-line/

  OR

  Taskkill (command line as well) http://technet.microsoft.com/en-us/library/bb491009.aspx

  Taskkill /IM hyperterm.exe

  kill hyperterm all windows open, BUT it will ask you if you want to close the sessions open, which I think that you do not want.

  Taskkill /F /IM hyperterm.exe

  voila (without chewing the com port, I just tried)

• I have a problem with the simulation in Matlab 6.5 and LabVIEW for PID controllers

  I have a problem with the simulation in Matlab 6.5 and LabVIEW. I have a few methods for granting regulators PID in MATLAB to go but not of LabVIEW. Degree of international teams of two transfer but when I passed to the fourth degree is no longer working. We have changed the formula to calculate the parameters for the fourth year and gave me some good values for assignment of Matlab, but when I put on LabVIEW are not resolved. the formulas are available in PDF format and are. Please help me and me someone if possible. Thank you
  Lim.4 generation in comparison methods and the MATLAB program settings are for the service of transfer to the second degree.

  Hello Lascarica,

  I noticed that you are using the screw of PID. Gains on these screws are based on TIME instead of GAIN. You should be able to build a PID regulator and vary the gains and then compare the results.

• I get a message that says that it is not backup because the backup of the disk image is already in use

  I get a message that says that it is not backup because the backup of the disk image is already in use

  If you have a Time Capsule...

  Make sure that no other Macs back up when

  Pull the power cord to the back of the time Capsule

  Count to ten

  Reconnect the power cord to the back of the time Capsule

  Wait a few minutes and try a backup

  Report on the results