An Alert Notification must be sent to each supervisor on use different

Similar Questions

• Alert Notification SAN HQ

  Hello team Dell,

  Had this error: hope you can help

  This message was generated by the service Dell EqualLogic SAN headquarters (version 2.5.0.6470) running on SaNHSVR

  The following conditions on the group EQL (MailScanner WARNING: digital links are often malicious: 150.xxx.xxx.x19) generated an alert notification:

  Warning conditions:

  • 23/07/2016 01:04:26 to 26/07 / 2016 09:02:46
    • [ID: 1.6] The Group EQL was added by using non well known address (MWKA). Delete and add the group using the well-known address 150.xxx.xxx.x21 management group.
    • The Group EQL was added by using non well known address (MWKA). Delete and add the group using the well-known address 150.xxx.xxx.x21 management group.
    • Condition has already generated an e-mail message. If the problem persists, additional messages will be sent approximately once every 6 hours.
  • 23/07/2016 07:16:20 to 26/07 / 2016 08:09:19
    • [ID: 3.23] ATTENTION: Network member EQL01-FLC Port isn't reachable.  Unable to get network for Member performance data.
    • Condition has already generated an e-mail message. If the problem persists, additional messages will be sent approximately once every 6 hours.

  NOTE: To customize the e-mail notification to alert launch an instance of the customer SAN seat then:

  1. Click on the 'Settings' button, then select "e-mail settings."
  2. Select the tab 'Notifications '.
  3. Select the group to edit.
  4. The upper part of the checkboxes allow enabling/disabling of all alerts in a specific category.
  5. The selection of the bottom contains allows enabling/disabling of individual alerts.
  6. Click on the "Apply" button to save the changes to this group or all groups.

  Hello

  You are running a very old version of SANHQ.   The current version is v3.2.

  The first error is quite simple, it seems that the incorrect IP address was used to add to this group.   What the dedicated management interface configured once it has been added to SANHQ?

  The 2nd error could be a connectivity issue, old SANHQ, old EQL FW or table was very busy at the time.  It could also be linked to the incorrect configuration error if errors refer to the same group.

  What a picture of model and firmware currently running?

  Kind regards

  Don

• CP Email alert: Notification title - collector down

  Why do I always received warning messages from CP even after I finished data collection?

  Example of email:

  Title of email:

  Alert about the CP: company - company_name: title of Notification - collector down

  The body of the email:

  Company: company_name
  At least a collection agent has failed after 423,0 hours

  CollectorSummary:
  Label	Host name	CollectorID	Last login	Number of hours
  col1-company_name	pc_name	colectorID_number	May 27, 2011 09:02	423,0

  Thank you

  Edemilson.

  Just to add to the excellent position of dcovery, a notification must have been set to transmit an alert if the closed collector communicating (download files) to the dashboard (optimize.vmware.com) and a subscription for this notification.

  It is a good idea to set the notification, but do not forget to disable it or UN - subscribe to it. This proactive notification setting ensures that data are collected on an ongoing basis.

  If the project is completed and the project/company hide option has been used, simply navigate to the home page and choose the tab "Show project or show companies" and select the item to view the company / project and execution however by disabling or unsubcribing from the notification.

  For more information:

  https://optimize.VMware.com/support/CP28_GettingStartGuide.PDF

• E-mail notification must be triggered on impact the apply changes?

  Hi all
  
  Creates a form similar to a form of appeal, whenever the user create a new request and submit the request. E-mail notification will be sent to the user and the administrator.
  Here when admin ppl rejects the request, an e-mail notification triggered by the user as the application was rejected.
  
  I have three radio buttons in the form
  
  1.submitted (Default).
  2.rejected.
  3.accepted.
  
  When the administrator change request and select rejected box and apply the changes, a notification e-mail should be raised to the user.
  
  Now I have a submit after process of change which is triggered whenever the user press on apply changes and it will send the notification to the user and admin time.
  How do e-mail notification which should be triggered when the administration rejects the request and submit the form?
  use the apex 4.0 version
  
  When the Admin selects the radio button of rejection and tha press on apply changes, then the notification by electronic mail must be sent to the user.
  
  Appreciate your help!
  
  Thank you and best regards,
  Robette.

  Hello

  Copy the following code,

  BEGIN
  
  IF(:ACESS_APPROVAL = 'Rejected')THEN
  
       APEX_MAIL.SEND('Your request has been rejected');
  
  ELSIF(:ACESS_APPROVAL = 'Accepted ' or :ACESS_APPROVAL = 'submitted')THEN
  
       APEX_MAIL.SEND('Your request will be notified.');
  
  END IF;
  
  END;
  

• Where is the setting to warn that "the information you entered must be sent over an unencrypted connection?

  Where is the setting to warn users to "information you entered must be sent over an unencrypted connection"?

  The settings for warning messages have been removed from the UI (Bug 513166).
  You must change preferences related security.warn_* directly on the topic: config page.
  
  Filter: security.warn

  You can check the security.warn_submit_insecure pref on the topic: config page.

  BTW: Firefox 10.0.3 ESR is not the last.

  • ESR 10.0.x Firefox: http://www.mozilla.org/en-US/firefox/organizations/all.html

• The FEP Server alert notifications do not display the correct time zone

  Time stamps FEP report

  When I receive my FEP Server alert notifications timestamps are far away. Nobody knows how to set the correct time zone, so the report will be accurate?  I think that the default time is UTC.

  Hello

  If you are referring to serve Advanced Endpoint Protection, I suggest you to report the issue in the link below:

  http://social.technet.Microsoft.com/forums/en/category/forefront

  I hope this helps.

• Z5 no longer displays the number of notifications that I have on each app

  Given that I've updated the marshmallow last night, my Z5 no longer displays the number of notifications that I have on each app :-( Does anyone else have this problem? Notifications will still appear in the notifications bar, but not on the applications themselves (the few).

  I just got some information about this. This is due to the fact that the snippet of code (API) which has been used by applications such as WhatsApp Messenger, to display unread messages, was not official, and is obsolete. The new API is shared among the partners and will require implementation on the side of the partner.

• Annoying Alert Notification SNMP SAN HQ

  Maybe if I add the email address of Mr Dell'Alba to this alert. Stop the madness. -This message was generated by the service Dell EqualLogic SAN headquarters (version 3.0.0.7189) running on vcenterserver.kembacu.org the following condition on WESTCHESTER (192.168.50.16) group has generated an alert notification: critical conditions: * 5/15/2014 13:39:37 * [ID: 14.2] could not establish the connection. * The HQ SAN server issued the group SNMP requests, some or all failed. This condition is probably due to the congestion of the network or has no network connectivity. The server will try again in 60 seconds. Check your network connectivity and that the storage group is online. If the problem persists, contact your Dell support provider. NOTE: In order to customize the email alert notification launch an instance of the customer SAN seat then: 1. click on the 'Settings' button, then select "e-mail settings." 2. Select the tab 'Notifications' 3. Select the group to edit. 4. the upper part of the checkboxes allow enabling/disabling of all alerts in a specific category. 5. the selection of the bottom contains allows enabling/disabling of individual alerts. 6. click on the "apply" button to save the changes to this group or all groups.

  Uncheck the event ID 14.2 (under review) and apply the change to all your groups... Please keep in mind that a restart of the service is necessary for entry into force of the amendments.

  Kind regards

  Joerg

• Notification is not sent to the role, activity of Notification status is "Complete" and result of the activity is "strength".

  Hi all

  I have a custom workflow that works very well and a requirement came to send the notification to a list of users after a certain activity is done. To achieve this,

  (1) I created notification and the attributes that are required,message.

  (2) I am creating a special role and assigning users before you initialize the workflow process, and this role is assigned to a type of role attribute that has been defined as the interpreter of the notification.

  When the workflow starts, the activity of notification is not sent to the role while its status is showing as 'Done' and result of the activity is showing that the 'Force' when the workflow process is completed.

  Note: Creating ad hoc-role and assign to users happen correctly, other notifications are bring sent to the respective recipients. Only the newly introduced notification does not work properly.

  Could you help me with this?

  Hi all

  I have fixed this problem.

  When I made the changes first, I kept the attribute type of the special role as text instead of role and I transferred it in the database using WFLOAD and I was faced with the issue of the notice, then I realized and changed the type of the role attribute and loaded in DB using WFLOAD command This time, only the changes are not stored in the DB and I faced the question again. So I thought that associates other issue and therefore posted in this forum (apologies for that).

  Yet once, I saved directly turns him into DB instead of load using WFLOAD, now it works fine.

  Kind regards

  K. Kumar

• in R12, we create magazines... Once created newspapers, we approve it. Then, there are some workflows processed will be made. Meanwhile, newspaper notification will be sent to the contractor of the person who throws the newspaper.  now that I could f

  in R12, we create magazines... Once created newspapers, we approve it. Then, there are some workflows processed will be made. Meanwhile, newspaper notification will be sent to the contractor of the person who throws the newspaper.  now, I could find the type of item for this workflow is: GLBATCH but you want to know the complete workflow process. for this I need wft file name.  Please tell us how to get the wft file.

  Workflow type: sheet

  Hello

  I ran these commands from a remote session (PuTTY, for example):

  CD GL_TOP/patch/115/import/US $

  grep 'ITEM_TYPE "GLBATCH" ' * wft

  I don't think this information is found in any table.

  Kind regards

  Bashar

• Customization of email alert notifications

  I was asked to change the verbiage of the e-mail alert notifications.  Is this possible?
  
  For example, we are currently receiving the following when the availability of a server changes:
  
  Subject: [HQ]! -[name of alert] [resource name]
  
  Message:
  [resource name] has generated the following alert:
  [name of alert] [resource name] Availability (0.0%)
  
  ----------------------------------------------------------
  RETAIL ALERT
  -Name of the resource
  -Name alert
  -Description alert
  -To attract the attention of Date / time
  -One or more trigger conditions
  -Alert severity
  
  Final metric indicator collected
  
  Can it be replaced by a message personalized, such as
  
  Subject: Database server has changed the availability status
  
  Message:
  Availability on the database server changed (0.0%).  Please review and, if necessary, log a ticket: [internal help desk URL]
  
  ?  Thank you

  Yes, it is possible. There are some documents to http://support.hyperic.com/display/DOC/Tailoring+Alert+Notification+Templates

• Emil Alert Notification

  I've created a form that end-users can submit via acrobat.com. Is it possible to have a script to report to the administrator of form (myself) a form has been submitted by a user as Asa soon they hit the submit button? Other possible solutions in what concerns the generation of an alert notification by e-mail with a script? Thank you in advance for your help!

  If you are unable to install a script on the local computer, and then you can not do

  in silent mode.

  There may be a possibility to go to Acrobat.com, but I'm not very

  familiar with this service. You might want to try the forum for it.

• LifeCam Studio must adjust settings to each Windows session

  Each time before use twinkle 'Lifecam Studio' I have to adjust all the settings like Zoom, 50/60 Hz and others...

  Savings by apply and OK is effective only during the Windows session...

  Is there a way to save these settings to a new desired adjustment? ...

  Thank you Jaime

  Hi Jaime,

  Thanks for the reply.

  We are happy to know that your problem has been resolved.

  You are always welcome in our community for other issues related to Windows.

• I use different e-mail accounts: I send an email with the sender A (standard!), email is archived to the sender sent archive and the email is sent to the sender, B

  A really strange problem!

  I use different e-mail accounts. I send an email with a sender (defined as standard!), email is archived in archive A sent from the sender, the sender is wrote in the header of the email as the sender, but the email is sent with the sender B written as the sender in the email received.

  Best regards, Michael

  It sounds like you do not use the right smtp server to send the e-mail.

  Please check what 'Sender A' smtp server account uses.
  'Tools' > 'Account settings' for the e-mail account
  or
  Right click on the email account in the folders pane, and then select "settings".
  Lower-right - outgoing (SMTP) server - select the correct SMTP server for that e-mail account.
  See the image below as an aid.
  Click OK

  If you are unsure about what to do please post the following information:

  In Thunderbird

  • Help > troubleshooting information
  • Click on 'copy text to the Clipboard.
  • In the forum, in this issue, right-click in a text box ' Post a reply ' and choose 'paste '.

  Tell me the number of the account which is "sender."
  Tell me the number of the account how recipient sees as venues.

• Mailing address: is it normal that the outgoing servers use different Port # on each device?

  I have problems with my Mail app, so I'm systematically review all parameters. Noticed that the port of the outgoing server is different on Mac, iPhone and iPad. Is this normal, or they are all should be the same for an e-mail account given?

  They should be identical, unless you use different protocols or of the security mechanisms on each device as a pop on a device and IMAP on another device or by using ssl for connection and tls for another. Check all the settings not only ports.