An inconsistency has been detected in your Interface.

Similar Questions

• An attack has been detected from your system. Please contact the system administrator.

  Hi I get Police and go to www.police.ir and get this error: we detected an attack from your system. Please contact the system administrator.

  I moved your message, assuming that you use not MSE. Note that the top-level domain. IR, is for the Iran. That might explain what you experienced when you navigate to this URL.

  -steve

• "" Se error message "No. DVD player has been detected on your computer" when you try to insert DVD

  Original title: DVD and CD Driver problems and do not know what to do! I need help...

  My dvd drive is not detected. For example, when I insert a cd, I can hear it running, but it is not bring up windows media player or DVD does not play. I ran a fixed and got Player error: No. DVD 2 was detected on the computer, and 2nd mistake was this player Windows Media can not be placed in properly and may not work as expected. He told me that the two problems are not fixed. I also follow steps start clicked then clicked on computer and then under duct only showing local disk C: and hp recovery D: I do not see a DVD or CD drive. Please help me it is frustrating.

  Hello

  
  1. what fixit did you run?
  2. were there any changes (hardware or software) to the computer before the show?
  3. What is the status in Device Manager?
  
  Run the FixIt mentioned below, if you have not tried and see if it helps.
  http://support.Microsoft.com/kb/314060
  http://support.Microsoft.com/mats/windows_media_player_diagnostic
   
  Hope this information helps.

• "A problem has been detected and Windows has shut down to prevent damage to your computer"... * STOP: 0x0000007e (0x805c49b8, 0xf7a172b4, 0 x 80000003, 0xf7a16fb0)... blue screen

  Hello!

  For the life of me I can't figure out how to get my machine to boot successfully. Nothing changes when I choose Safe Mode, last known good Configuration, enable VGA Mode, booting, Directory Services Restore Mode or Debug Mode logging.

  It's very stressful, because I'm right smack dab in the Middle a semester at the College. I have most of what I currently need access to supported illuminates... but not quite all :( It is also very reassuring to be able to take care of the school of work away from the library of the University. Yesterday, my computer was working fine... I think that Windows has completed an update, if I can't remember now. As I woke up this morning, I was not able to boot all the way to Windows only once.

  My laptop is a HP Pavilion dv6000 running XP Media Center, and I have not installed new hardware since I bought the machine about 3 years ago.

  Here are more details, where they can help in the diagnosis of my problem:

  • ID of the system board: 30BB
  • Type of processor: Genuine Intel(r) CPU T2250
  • Processor speed: 1730 MHz
  • Total memory: 1024 MB
  • Video memory up to: 128 MB
  • BIOS version: F.06

  Here's the entire message to the blue screen:
  - - - - - - - - - - - - - - - - - - - -
  A problem has been detected and windows has shut down to prevent damage to your computer.

  If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:

  Make sure you have enough disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video cards.

  Check with your hardware vendor for updates to the BIOS. Disable the BIOS memory options such as implementing caching or shading. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and then select Safe Mode.

  Technical information:

  STOP: 0X0000007E (0X805C49B8, 0XF7A172B4, 0 X 80000003, 0XF7A16FB0)
  - - - - - - - - - - - - - - - - - - - -

  I also learned to a blue screen that says something about "PAGE_FAULT_IN_NONPAGED_AREA". I think that this happens when I try to start safe mode.

  Also, I never did much with computer problems beyond what could be repaired with the restoration of the system... so not being is not able to boot at all me has to stop. Please, I beg you! Help me?!

  With great appreciation for your time,.
  Damaya

  Quick suggestion

  Some HP partition the hard drive. have you tried to type F11 or F12 during startup (before that he go to the option mode start screen)? It might take you for a HP recovery program in that partition (because windows don't be loading not to use that recovery)
  Good luck

• When I turn on the computer, the screen indicates "a problem has been detected and windows has shut down to prevent damage to your computer.

  Original title: when I turn on the computer.

  the screen shows "a problem has been detected and windows has shut down to avoid damaging your computor.

  Hi Cjdaniello,

  ·         Did you do changes on the computer before the show?

  Follow the suggestions below for a possible solution:

  Step 1: Start in safe mode and check if the problem persists.

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Step 2: If the problem does not occur in safe mode, you can put your system to boot (in normal mode) to solve the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  I hope this helps.

• Satellite T210 - error has been detected by the cooling system

  I hope someone can help out me, I had a my laptop for almost a year, it's a T210 and occasionally it comes up with the following pop upward:

  WARNING: A problem with the cooling system has been detected. Please turn off your computer immediately and return it for service.

  If I click ok it does not go far but its obviously not resolved as long as he keeps breed. Any ideas what the problem is and if it is an easy fix or am I'm going to have to send it back to Toshiba?

  Thank you

  Hello

  Yes I know this error message that some people here in the forum reported the same error message and it seems to be a software bug
  The cooling modules are ok.

  As far as I know the new recovery system would solve this
  However, you should not be afraid that something is wrong with the cooling module system

• Win XP (32-bit) with iTunes 12.1.3.6: iPod Nano A1320 16 GB error: an iPod has been detected, but it could not be identified properly.

  I have the following environment:

  Win XP SP3 (32 bit)

  iTunes 12.1.3.6

  iPod Nano A1320 16 GB (5th generation)

  I get an error when I try to connect my iPod Nano A1320 16 GB (5th generation):

  An iPod has been detected, but it could not be identified properly.

  Please disconnect and reconnect the iPod and try again.

  If the problem persists, uninstall iTunes and then reinstall iTunes.

  I tried my other iPod Nano A1320 16 GB (5th generation), and it gives the same error.

  I looked at other similar positions with this error message and tried their solutions, but none of them does not seem to work.

  However, my iPod Nano A1285 8 GB (4th generation) is recognized by iTunes 12.1.3.6.

  Any suggestions? Thanks in advance for your help.

  Since it's Windows XP, it's maybe the old problem of the "drive letter".  Being a Mac user, I don't know the exact procedure, but try changing the drive letter of the iPod.  Maybe that's how

  Change the drive letter for iPod

• Satellite C660P - 11 p and WXP - problem has been detected

  I tried to install OS XP Professional SP1 + SP2 on my Toshiba Satellite C660P - 11 p, but after aprox. 1 minute from starting installation of Windows, the following message was displayed:
  "A problem has been detected and Windows has shut down to prevent damage to your computer. If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again follow these steps:
  Remove any newly installed hard drives or hard drive controllers. Check your hard drive to ensure that it is properly configured and completed. Run CHKDSK/F to check for hard drive corruption, and try again.

  I tried to install OS again, and the same message appeared.
  I don't know what I can do to solve the problem.
  How can I remove the installed hard drives or hard drive controllers?

  Thank for your help anticipate

  And during the original installation of Windows 7 everything becomes OK?

  I put t know what you mean with SP1 + SP2, but when you want to install WXP Windows XP edition family SP2 or WXP including SP3.
  You have loaded driver SATA?
  You use the compatibility mode for the SATA option in BIOS?

• Qosmio G20 error message: problem with the cooling system has been detected

  I'm trying to fix a Qosmio G20 (which is about 3 years old, it is no longer in warranty).

  Error message: Warning: a problem with the cooling system has been detected.

  I managed to remove the outer case and observe the operation of the machine, and basically one of the fans does not at all. The fan which is closest to the power connector seems to work very well (he seems to be turning a lot, do not know if this is normal), but the other fan who does not seem to move at all.

  When I put in place the case and on the machine, I noticed after a few minutes the vent of the fan working heat sink had warm enough, while led the non-working fan remained cool.

  I cleaned the fan from dust and have also changed the BIOS battery mode mode high performance, but the problem still exists.

  I would be grateful if someone could give advice if the problem is the fan or something else.

  If the fan is the problem, where I can buy a: i live in the United Kingdom?

  Hello

  I think there might be something wrong with the cooling module and the replacement would be necessary.
  Usually, this should be done by an authorized provider (ASP) in your country.

  Technicians could replace it with a new part and also could renew the thermal grease which is placed between the module and the CPU cooling.

  So contact the ASP in your country and ask for later handling.

  By the way; also, you can buy the cooling of the ASP module!

  Good luck

• Satellite A40 - attention: problem with the cooling system has been detected.

  Hello guys,.

  From time to time, I get the following message is displayed:

  WARNING: a problem with the cooling system has been detected Toshiba
  Please turn off computer immediately and return it for service.

  I have Windows XP on it.
  I opened the cooling fan and clean it. Of course, I found it dirty rally.
  But still, I get this message!
  What should I do?
  I live in Northern Germany.

  Any advice is welcome and thanks in advance.

  Ibrahim

  Hello

  The message says it all!
  In this case you should contact the service provider authorized in your country!

  > I opened the cooling fan and clean it. Of course, I found it dirty rally.
  Eventually, the cooling modules don t like needs and that is why the message again!

  Nothing to my friend... you need help laptop technician

• Satellite L40 - 14N: problem has been detected and windows has been shut down

  Help.

  My laptop worked perfectly well until my son used last night and went on various games.
  Since then when you turn it on, it is a blue screen that says: "a problem has been detected and windows has shut down to prevent damage to your computer.

  He said that he has downloaded something or added a new hardware or software.
  So, off it and tried.
  Have tried everything to make it work. tried to get into F8 and F12.

  Tried from the safe mode and the recovery disc tried following all the resulting instructions always blue screen.
  Not knowing what else to do. I have

  s he Knackared now?

  As I got the BSOD appears also after the use of the disk recovery and after a fresh install of the OS.
  Is this right?

  Unfortunately, buddy, but sounds more like a hardware problem as a problem related to sound.

  I would contact a technician for laptop and organize an audit of the material.

• Installation of Bank UAOnline interrupted. A dangerous request.querystring has been detected

  online banking installation interrupted. A dangerous request.querystring has been detected

  What your bank has to say about it?

• When I try to play a game! all I get is "a debugger has been detected _ unload the debugger and try again.

  I did evry thing I can think and what's on the net
  CAN ANY 1 CAN HELP ME!

  Hi buddy300,
  Welcome to Microsoft windows vista forums!

  a. this happens only with games?

  b. remember that any changes made to your computer before this problem?
  Have c. you installed a software debugger on the computer?

  This problem may occur if one or more of the following conditions are met:

  ·         There are programs (for example, an antivirus program or debugging software) that run in the background and that interfere with the game startup process.

  ·          Your sound card or sound card drivers are outdated.

  ·         His Creative Audigy card is installed on your computer. This sound card may conflict with the game startup process.

  I suggest you do the following:

  Step 1: disable the security software on the system tray and then check.

  (Note: enable security software after the test)

  Step 2:

  Put the computer in a clean boot (namely if any third-party software hinders the process)

  http://support.Microsoft.com/kb/929135 ---> how to solve a problem by performing a clean boot in Windows Vista or in Windows 7

  Check with step 1 (run a clean boot):-If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem.

  Continue with the remaining steps to pin-point on the third party service.

  (Note: after find you the problem causing the program, you will have to perhaps to update or install a newer version of the program and also don't forget to put the computer to a normal startup)

  Step 3: try the steps mentioned in the article

  Games: Error Message: a debugger has been detected: unload the debugger and try again

  http://support.Microsoft.com/kb/812759

  Step 4: System Restore: -to restore the operating system to an earlier point in time, follow these steps:

  a. Click Start, type system restore in the search box and then in the list click on the system restore program. If you are prompted for an administrator password or a confirmation, type your password or click on continue.

  b. in the System Restore dialog box, click on choose another restore point and then click Next.

  c. in the list of restore points, click a restore point created before you started having the problem and then click Next.

  d. click Finish.

  e. the computer restarts and system files and settings are back to the State they were in at the time where the restore point has been created.

  Thank you, and in what concerns:
  Ajay K
  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Problem has been detected and windows has been shutdown error STOP: 0x0000008E. Get the memory dump after you have installed the trial version of MS Project 2010.__space.

  Original title: problem has been detected and windows has been shut down. Get the memory dump after you have installed the trial version of MS Project 2010.__space.

  Computer Message: Check if you have enough disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video cards.

  Check with your suppliers of material, updates the BIOS. Disable the BIOS memory options such as implementing caching or shading. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to start advance startup options, and then select Safe mode.

  Technical information: * STOP: 0x0000008E (0xC0000005, 0x8054556C, 0xADB78A98, 0x00000000)

  Beginning physical memory dump

  Total physical memory dump. Contact technical support for further assistance group.

  Hi fernandomventura,

  Step 1: Disconnect all external devices (printers, scanner, USB (universal serial bus) readers, etc...) Except the keyboard and mouse and then start.

  If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue.  Then get any drivers\software update for the device.

  Step 2: Follow the steps mentioned in the articles below which deals with a similar question

   

  General troubleshooting for an error message that you receive randomly in Windows XP: "Stop 0x0000008E"-restore the system to achieve ".

  http://support.Microsoft.com/kb/945658/

  You receive a random "0x0000008E" error message on a blue screen in Windows XP

  http://support.Microsoft.com/kb/827663

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Whenever I try to download anything on my laptop, I get a message saying that a virus has been detected and it is deleted.

  Whenever I try to download anything on my laptop, I get a message saying that a virus has been detected and it is deleted. So I can't download files or even virus scans. Help, please...

  Hello

  Read the answer to your problem through The ball in this thread link.

  "I get the error message"xxxxx.xxx"" contains a virus and has been eliminated ' downloads... on all software updates from microsoft ".

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-security/i-get-error-message-xxxxxxxx-contains-a-virus-and/fbb5e0fd-63bd-4E01-9a98-6074d33a8fd6

  See you soon.