analysis of the problems since installing windows 10 / Office 2016

Similar Questions

• Partitioning of the problems when installing Windows 7

  I have a HP Compaq CQ58 supplied with Windows 8. I switched to Ubuntu and I'm doing a clean install of Windows 7. Installation came at a prompt asking "Where do you want to install Windows?" and I have three partitions:

  Disk 0 Partition 1 - 94.0 MB system
  Disk 0 Partition 2-296, 4 GB primary
  Disk 0 Partition 3-1, 6 GB primary

  When you select one of them, I get "Windows cannot be installed to Partiion Dis 0 x." On the 1 (System) partition, the details are:

  Windows cannot be installed to this disk. The selected disk is the GPT partition style.

  Windows cannot be installed to this hard disk space. The partition is a partition of EFI (ESP) system.

  On Partition 2 (primary), the details just say:

  Windows cannot be installed to this disk. The selected disk is the GPT partition style.

  And on the Partition (primary) 3, tell the details:

  Windows cannot be installed to this disk. The selected disk is the GPT partition style.

  Windows cannot be installed to this hard disk space. Windows must be installed on a partition formatted in NTFS.

  Windows cannot be installed to this hard disk space. The partition is of an unknown type.

  Well, I had nothing in particular requiring a backup (it is a computer of leisure, all of our important data are on other devices), then I hit the "Format" button on all three in turn try to get the installation to run on one of them. If any OS at this point is completely erased. I need to know, now, what to do. I'm not comfortable with my computer knowledge to go and delete partitions without professional opinion. I'm not used to have more than one partition and wouldn't mind consolidating unless HP has good reasons to keep them separate.

  Hello

  There is no reason to keep these partitions and you can remove them using the disk management on the following installation disc.

  Left click a partition for highlight.

  Click the blue link "drive Options (Advanced).

  Select the option 'delete '.

  Repeat this step for each partition listed.

  Once completed, you should see only 1 entry showing that "the unallocated space on disk 0.

  Click on the button 'Next' operation of installation of Windows 7.

  Be aware that Windows 7 will also create a "System" of about 100 MB hidden partition that contains the files and start the recovery environment.

  Kind regards

  DP - K

• Since installing windows 10 display problems

  I am new to these forums and I hope someone can help me with a problem since installing windows 10 last night, I. When I opened the premier, everything seems to go well except I get no video previews in the source or timeline panels. When I play the clip I can hear the audio but just get a white screen where the video should be.

  I tried to open an old project, create a new project and import a mp4 clip over and the same result.

  I tried to switch back compatibility on windows 8 and empty my cache of media folder.

  I use the latest version of the first pro, but when I went to update this morning I also get an error message.

  Everyone knows about it or have any solution?

  Thanks in advance

  Hi Meagan,

  I would say that switching video converter.

  Go to file > project settings > General and change the "Video Renderer" to "only Mercury playback engine software. Click 'OK' and select "Remove the Previews". Save the project and then restart Premiere Pro.

  Hope that helps.

  Regalo

• NVIDIA GeForce 6600GT driver has stopped working since installing Windows 7 updates. Why? And how to remedy the situation. Tried uninstallingc download update drivers, etc. Still no luck.

  NVIDIA GeForce 6600GT driver has stopped working since installing Windows 7 updates. Why? And how to remedy the situation. Tried uninstallingc download update drivers, etc. Still no luck.

  Message that appears is: -.

  Windows has stopped this device because it has reported problems. (Code 43)

  BB

  Install the latest driver from nVIDIA:

  http://www.nvidia.com/object/Win7-WinVista-32bit-260.99-WHQL-driver.html

  http://www.nvidia.com/object/Win7-WinVista-64bit-260.99-WHQL-driver.html

  "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

• [SOLVED] Problem - cannot install Windows XP on C dive - only option is the D drive.

  Hello

  I'm doing a clean install of windows xp pro on a hard disk with unallocated space at the front of the drive and a primary partition containing the data at the end of the training.

  I want to install windows xp pro on a primary partition on the front of the disk on drive C.

  Here's my problem:

  When I was installing windows xp pro, I noticed that when I created a partition in the unallocated space at the front of the car where I wanted to install windows xp pro, that I couldn't C as a drive letter for the installation drive - d only.

  I ran the installation at the end and Yes, windows xp pro did install on drive D - this isn't what I want - I want it on the C drive.

  Can someone tell me how I can solve this installation problem.

  Should I run a partition boot CD and set up a primary partition on the front of the drive before installing windows xp pro?

  Thank you very much.

  I solved this problem by following these steps:

  1. I installed a second hard drive (old sata drive).

  2. I installed windows xp on the second hard drive.

  3. I photographed the windows xp install from the second disc on the first hard drive.

  4. I deleted the second disc.

  5. I've rehearsed with my other computers.

  Everything works fine - just takes a little longer than expected.

• SCANNER NOT SCAN SINCE INSTALLING WINDOWS 10

  C4500 all in one printer/scanner.  Since installing windows 10 I can't scan.  Printing/copying is fine.   When I press 'New Scan' it says "connection with C4500" and then just said "Couldn't complete analysis" have no idea what to do!  Any help much appreciated

  Hi Sandra,.

  Try these step.

  You should preform is a complete uninstalltion the driver 14 (Solution Center) of your computer. (Importnet thing: If your computer is also a HP Machine, follow the steps later!)

  1 Unplugg your device (if its without wireless/Ethernet, skip this step)

  2 download the complete solution (here: http://ftp.hp.com/pub/softlib/software13/COL30130/mp-109997-3/PS_AIO_04_C4500_USW_Full_Win_WW_140_408-5.exe()

  3. after it finish downloading, extract the software and head in the printer folder that is displayed there, inside the head to the "util" folder and then in the folder "ccc" here you should be able to find a file named "Uninstall_L4" > run this file, it will open a black window, just press enter in so he can start to remove the software , after it is completed you will be asked to perform a restart of uninstalling, save that you were working and let it restart.

  4. after he has finished start up, head in C:\Program Files (x 86) and delete the 'HP' folder you see here.

  5. head in C:\Program Files (x 86) \Common Files and delete the folder "Hewlett-Packard" you see here.

  6. here, we will make changes to the registry, that before we start backup your registry entries by exporting your registry library on your desktop. (Follow these steps on how to do this)

  6.1.open to the top of the window "Run" by pressing the win key + R.

  6.2.in the command line type "regedit" and press on enter, he will open the registry editor.

  6.3.in this window at the top left, tap on 'file' and choose 'export', name the "reg" file and save it to your desktop.

  7. here are entering HKEY_CURRENT_USER\Software and remove the HP/Hewlett-Packard folders that you find here.

  7.1.head in HKEY_LOCAL_MACHINE\SOFTWARE and remove the HP/Hewlett-Packard folders you find here.

  8. open the window "Run" again by pressing Win - key + R, in the type of command line in "spool" in here to open the "drivers" folder, it opens the folder "x 64/W32x86" (depending on your system) and then remove the HP printer folder. (If the there is no HP folder delete anything.)

  9. go to C:\Windows and rename the old "twain_32" "twain_32" folder

  10. open the command-line by pressing Win - key + R in the type of command line under "%temp%" in the folder that will be opened, remove all.

  11. next step invlove will using the cleanup utility Windows, which can be downloaded here (http://www.google.co.il/url?sa=t&rct=j&q=&esrc=s&f rm = 1 & source = web & cd = 1 & cad = AJLN & uact = 8 & ved = 0CBwQFjAA...), after it's finished downloading install the file (right click and run as s Adminitrator) and open the software, a small window will open , in he search anything that starts with HP and remove it... (Everything is being shown as HP except for a file called "bdq_scan" take care to delete this file as there are 97% chance that that is the only reason for your problem..)

  12 restart your computer.

  13 start the installation and follow the steps as shown.

  __________________________________________________​_________________________________________

  Incase you are using an HP computer.

  In step 4, venture into C:\Program Files (x 86) \HP and only delete the folder "digital imaging".

  Skip - 5,6,6.1,6.2,6.3,7,7.1 and 11 completely.

  And this should solve the problem, good luck.

• Problem after installing Windows Service Pack 3 on Windows XP Home edition error Media pc: files which are required for Windows to run properly have been replaced by unknown...

  Original title: problem after installing Windows Service Pack 3 on Windows XP Home Media edition pc

  My pc runs Windows XP Home Media edition.  I installed Windows Service Pack 3 successfully, or so I thought. Whenever I turn on my pc a box opens indicating "files which are required for Windows to run properly have been replaced by unrecognized versions."  To maintain the stability of the system.  Windows must restore the original versions of these files.  Install your Windows XP Professional CD2.  I don't have any Windows XP Professional CD that I use the Home Media Edition. If I press Cancel repeatedly, the window disappears to return with the same information, but ask me to install Windows XP Professional CD3.  How can I stop this happening?

  Hello

  Step 1: I suggest you perform the SFC scan on the computer and check.

  SFC tool scans system files and replaces incorrect versions of system files by using the correct versions.

  To run the System File Checker tool, follow these steps:

  1. Click Start and type cmd in the box start the search.
  2. right click on cmd in the list programs and then click Run as administrator.
  If you are prompted for an administrator password or a confirmation, type your password or click on continue
  3. at the command prompt, type the following line and press ENTER:

  sfc/scannow

  Reference: http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/system_file_checker.mspx?mfr=true

  Step 2: Also, look for error messages in the event viewer. If you find error messages after return the exact error message so that we can help you better.

  Reference:
  Using the event viewer
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/snap_event_viewer.mspx?mfr=true

  Understanding of event viewer
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/event_overview_01.mspx?mfr=true

  Procedure to view and manage event logs in Event Viewer in Windows XP
  http://support.Microsoft.com/kb/308427

• Replacing hard drive, made restoration of the factory, get the message error "installing windows could not configure windows to run on a hardware on this computer."

  OS = Windows 7

  Computer = Gateway FX6840
  Media = gateway recovery media
  Hard drive is set to AHCI in BIOS

  I started meeting with S.M.A.R.T. errors.

  I backed up my data.

  I replaced 1 TB Seagate original with a new 2 hard drive to Seagate Barracuda SATA STBD2000101. Computer is equipped also is from the factory... no additional or modified facilities.

  I tried to restore Windows 7 from the rescue of the disks created with the "Gateway Recovery Management"

  Windows copying files over, the machine restarts, it installs the devices, then it stops at the "installation program starts services" and a window opens with the message "windows Setup could not configure windows to run on a hardware on this computer.

  I can't apply the Article ID: 2466753 because the process of restoration of the plant seems not provide an option to load a driver .

  Any help would be appreciated... Gateway is only interested to collect money.  They have no interest in serving the poor suckers who buy their products (computer is 2 years old so it is out of warranty).

  Thanks for the reply.

  Fortunately, I solved the problem myself (after 19 hours of stress).
  The problem is that the recent hard disk has something different that no longer ages and makes pre-service pack 1 (SP1 solves the problem) versions of Windows 7 incompatible. My set of recovery disks have been created the day I bought the computer, which had no windows updates installed at the time.

  There is an "easy solution" on the Microsoft support site: http://support.microsoft.com/kb/2466753/en-us

  Unfortunately, their method works only if you have a Windows 7 installation disc, which does most of the people who buy computers pre-built manufacturers. Essentially, the solution is to install SP1 from a disc when don't give you the possibility to load drivers during installation, an option that the gateway recovery disks.

  So I thought that, theoretically, if I use my recovery discs to get a clean install on a hard drive that works, then use windows update to get updated (or at least to get SP1), and then make a set of NEW recovery disks (using windows backup: start > all programs > maintenance > Backup and Restore), I should be able to use these discs to install the new hard disk.

  It worked.

  So for someone else who has this same problem with new hard disks, I hope that the above is easy to understand. If not, ask someone else more savvy and show them this thread. Do not forget that at the end to create new recovery disks, it will ask you if you also want to create a 'system' repair disc. DO THIS! This is the disk that you need to start from when you are ready to install.

  Also: If your new hard drive is bigger than the one that you have created the new recovery disks, the partition on your new hard drive (once everything is installed) will be the same size as the one that you have created the records on. You will need to use a kind of editor of score for re - size. I recommend Gnome Partition Editor. http://www.gparted.org

  Burn gparted Live CD and him, resize your partition, and you're done (google for more in-depth instructions).

  Thank you, theloungelizardK, for the offer on the ISO, but I don't need. :)

  Eastan - ITF

• I received two copies of every email that I receive. My mail provide tells me that the problem is in Windows Mail.

  My mail provide tells me that the problem is in Windows mail. My operating system is Vista.

  original title: mail all delivered in duplicate.

  Check in tools | Accounts and make sure that you have not implemented the duplicate accounts.

• Windows could not complete the installation. to install windows on installation of HP DV6-7007TX, this restart of the 64-bit computer

  I buy a new HP Pavilion DV6-7007TX. I don't want the pre loaded Windows 7 Home Premium 64 bit that's why I decided to format it using Windows 7 Ultimate 64 bit, but after reboot before the Installtion "filling" to finish an Error Message is displayed "windows cannot complete the installation. to install windows on installation, this restart of the computer", I rebooted several times but the same error pops up

  Why not just do you do an Anytime Upgrade of Windows 7 Edition Home Premium to Windows 7 Ultimate?

  If the license for Windows 7 Ultimate, you have access to is a retail version update or complete, you can use the product key and the Express upgrade to Windows 7 Home Premium to Windows 7 Ultimate. First of all, check that the edition of Windows 7, you are upgrading is already enabled (if it isn't, you will encounter complications and that you might start all by performing a clean installation). Click Start, type Anytime Upgrade, click on the option enter a key, enter the key of Windows 7 Ultimate edition at the request, click Next, wait while checking the key, accept the license agreement, click on upgrade, wait while the software upgrades, (it may take 10 minutes or more depending on the if updates are required) your computer restarts automatically, after the reboot, Windows 7 will notify you updating the computer, the computer will restart once more automatically and will be completed the upgrade, a window will appear notifying the upgrade was successful and your computer is ready to use, click Close, you should be upgraded to Windows 7 Ultimate files the stored settings and programs.

• Satellite A300-1EG: problem with the touchpad after installing Windows 7

  Hello!

  I had a problem with my touchpad since I installed Windows 7 (64-bit version) on my laptop (Toshiba) A300-1EG.

  I tried many different solutions to this problem.
  I checked the alignment of the touchpad (be it on) in the BIOS, I tried to install several drivers (on a site of Synaptics, automatically by Windows) and none of these work. Of course, I tried FN + F9 key combination.
  When I check the alignment of the touchpad in the Control Panel, everything seems fine. It is written, that "device working properly.

  I have Toshiba Software, what may be the cause of the problem?
  But I have no idea where I can find something.

  I'd appreciate any help.

  I hope to be understandable - English is not my mother tongue :) Thank you very much in advance for any ideas. :)

  Hi mate

  I'm not quite sure what problem you have but you should first try to install the necessary drivers touchpad m.
  Maybe you used the wrong driver in the past

  So Sat A300-1EG belongs to the series of PSAG4E.
  The European driver Toshiba page does not provide a special touchpad driver for Win 7 for this device.

  But I noticed that Win 7 64 bit drivers touchpad (Alps & Synaptics) for Satellite L500 PSLS3E series is released on the European driver page.
  Try both drivers Touch Pad for this device and test it!

  Welcome them

• HP Officejet 7612: analysis of problems after installing Windows 10

  After installing Windows (prior to Windows Vista) 10, scan documents with my HP Officejet 7612 became a hell of a job.

  Printing is no problem.

  With Webscan, I can only scan and save 1 page at a time, I can not scan several pages of the document 1 more.

  I downloaded "Extended Scan" but when I try to use this app, it says "year error occurred while scanning" without more information.

  With "HP Scan and capture" I can't scan the size of A3 paper full of documents and there seems to be no possibility to change the size of a3 paper. Maximum size is 'legal letter '.

  Same problem with "Windows Fax and scan."

  Are there other ways to recover the possibilities of full scan from my HP Officejet 7612?

  Hello
  
  Thank you for using the HP Forums.
  
  You can download and install the software COMPLETE features of HP printing for your operating system:

  The following resources will help you:
  
  HP printer install wizard for Windows
  http://ftp.HP.com/pub/softlib/software13/COL50403/MP-150580-2/hppiw.exe
  
  Once you have downloaded and installed the software, FULL of features, you will be able to print and scan.
  
  Hope that helps.

• Since installing Windows 7, two keys on my keyboard are mixed. I hit the (@) but ("") is displayed instead.

  After installing windows 7 on my laptop (acer extensa) 4620 when I hit the button "double quote" (""), "at the rate' (@) is printed.

  and when I counter stike the key "to the rate' (@), double quotes (" ") is printed...
  the problem is that with these two keys.
  Bobby
  India
  Original title: keyboard has changed

  Hello

  Is - this specific problem with a particular application?

  Check if it works fine with the keypad.

  http://Windows.Microsoft.com/en-us/Windows7/type-without-using-the-keyboard-on-screen-keyboard

  You can also check if the problem is keyboard or does not connect the external keyboard.

  I suggest you to fallow the below methods:

  Method 1:

  Run the fixit available in the link below and check if that makes a difference

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Method 2: update the driver from the manufacturer's Web site

  Try the link below how to download drivers automatically:

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  http://Windows.Microsoft.com/en-us/Windows7/automatically-get-recommended-drivers-and-updates-for-your-hardware

  Method 3: Check in SafeMode with network.

   

   

  You can also check if the problem persists in safe mode with network and check.

  Reference:

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode

  If the key on the keyboard does not work, then fallow method 4.

   

  Method 4: Perform a clean boot and check.

   

  To help resolve the error message, you can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  
  Please note:  After troubleshooting, be sure to start your computer in normal mode by following step 7.

  For more info:

  http://Windows.Microsoft.com/en-us/Windows/help/Mouse-touchpad-and-keyboard-problems-in-Windows?T1=tab04

• I was referred to this site. Problems with installing Windows on the new drive.

  Greetings!

  I just installed a new hard drive on my Mini 311 1037. I bought the HP recovery discs. The operating system is Windows 7 Home Premium (I guess it was the correct operating system for that computer). The installation seemed fine, but after installing the drivers, I get the message, "Windows Setup could not configure windows to run on a hardware on this computer."  Then after the restart, after the initial windows screen, I get a message that says "Windows cannot complete the installation. To install Windows on this computer, run the Setup again. "I atempted to iireinstall 3 times. All diagnostic tests are good: the hard drive, the memory. I have no idea what to do next. Help, please?

  If you can read the Microsoft Windows 7 of 25-character license key, you can download a Windows 7 ISO file to burn to a DVD or USB flash drive. The version must match that's installed on your PC as shown on the sticker COST Microsoft fixed on the bottom of the laptop. Like Windows Home Premium.

  Links to downloads of Windows 7 ISO files:

  http://www.mydigitallife.info/official-Windows-7-SP1-ISO-from-Digital-River/

  Use the installation of Windows 7 USB/DVD tool to convert the ISO file you download. Link and instructions below. You need to a DVD + R or DVD - R. Or a flash drive 4 GB to use the USB method.

  http://www.microsoftstore.com/store/msusa/HTML/pbPage.Help_Win7_usbdvd_dwnTool#installation

  Use 25 characters on the COA key to activate the installation.

  The key will activate a 32 or 64 bit installation.

  Then, go to the page support and driver to install the drivers you need.

• Problem with installing windows xp the drive mounted iso in windows 7

  Hello everyone, I am currently using Windows 7 and I would like to install Windows xp. However, I do not have a CD player, so I just have to install the .iso files. When I mounted the image Poweriso .iso file and run the installer there, he opened a window with a few options to choose. And I was surprised to see that the option "Install Windows XP" is grayed out, which means that it is not available. Can someone help me to activate Setup option to install the OS?

  You can see the screenshot here: http://www.mediafire.com/?h6v5l3qnx6mfvt8

  Thanks in advance for your help.

  Best regards

  Mar

  Hello

  You cannot boot from the iso mounted, you must have iso burned to the disc.

  Thank you

  Nitin Aswani