AnyConnect VPN Setup Assistance
Hello world. I installed a new ASA to replace my current and need a bit of help with installing AnyConnect. I think I have everything set up correctly, until my exceptions NAT I can successfully connect to the ASA via the page without customer and the AnyConnect client, but can't pass the SAA, so I guess its exceptions NAT I was looking at both the ASA_cli.pdf but can't seem to nail down. It is not yet using the ASDM, which I don't usually do for VPN, as easy as asdm 6.1 statement.
On my current ASA, I know that I have an ACL called sheep. For reference, my internal networks is 10.0.x.x, and my ip for VPN users pool is 192.168.2.x.
Any help would be greatly appreciated. Thanks in advance
.
Add DNS and WINS servers to corresponding Anyconnect group policy so that it is possible to clients when they connect. Also, make sure that the servers are accessible when connected via Anyconnect.
Tags: Cisco Security
Similar Questions
-
Hi all, I'm going to have bad configure anyconnect VPN on my router. I'm CCENT pre level and especially followed a tutorial, but feel I'm missing something simple here.
It's a fairly simple installation on a Cisco No. 2851 - faces of a single interface my LAN 192.168.1.0/24, the other has a public IP address.
I created a network 192.168.2.0/24 VPN users, mainly to have phones Android connection of their mobile phone networks, and have access to the servers/security cameras/etc by using their local IP addresses. When my phone connects, it gets an IP address and is connected, but is not communicating with my LAN correctly.
The VPN client can ping 192.168.1.254 (the router's LAN IP) - but not the other devices on the network. However, the devices on my LAN can ping the VPN clients to their address 192.168.2.x.
Here's a copy of my current config, I have reorganized some elements with #s. Also pasted my ip sh road under him. Do not forget that I am a novice, please forgive the hack :)
Router (config) #do sh run
Building configuration...Current configuration: 5782 bytes
!
! Last modification of the configuration at 02:24:24 UTC Sat Sep 5 2015 by #.
!
version 15.1
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
host name #.
!
boot-start-marker
boot-end-marker
!
!
enable secret $5 1$ 0 #.
!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login local sslvpn
AAA authorization exec default local
!
!
!
!
!
AAA - the id of the joint session
!
!
dot11 syslog
no ip source route
!
!
IP cef
!
DHCP excluded-address 192.168.1.200 IP 192.168.1.254
DHCP excluded-address 192.168.1.1 IP 192.168.1.10
!
pool of dhcp IP LAN
network 192.168.1.0 255.255.255.0
Server DNS 192.168.1.254
by default-router 192.168.1.254
!
!
IP domain name # '.com'
host IP Switch 192.168.1.253
8.8.8.8 IP name-server
block connection-for 2000 tent 4 within 60
connection access silencer-class SSH_MGMT
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
!
!
!
!
!
!
!
!
!
voice-card 0
!
Crypto pki token removal timeout default 0
!
Crypto pki trustpoint TRUSTPOINT-MY
enrollment selfsigned
Serial number
name of the object CN = 117-certificate
crl revocation checking
rsakeypair my-rsa-keys
!
!
MY-TRUSTPOINT crypto pki certificate chain
certificate self-signed 01
###################################################
quit smoking
!
!
license udi pid CISCO2851 sn FTX1026A54Y
# 5 secret username $1$ yv # E9.
# 5 secret username $1$ X0nL ###kO.
!
redundancy
!
!
property intellectual ssh version 2
!
!
!
!
!
!
!
!
interface GigabitEthernet0/0
LAN description
IP 192.168.1.254 255.255.255.0
IP nat inside
No virtual-reassembly in ip
automatic duplex
automatic speed
!
interface GigabitEthernet0/1
WAN description
No dhcp client ip asks tftp-server-address
No dhcp ip client application-domain name
DHCP IP address
IP access-group ACL-WAN_INTERFACE in
no ip redirection
no ip proxy-arp
NAT outside IP
No virtual-reassembly in ip
automatic duplex
automatic speed
No cdp enable
!
interface Serial0/0/0
no ip address
Shutdown
!
interface virtual-Template1
!
local IP 192.168.2.100 WEBVPN-POOL pool 192.168.2.110
IP forward-Protocol ND
no ip address of the http server
no ip http secure server
!
!
The dns server IP
IP nat inside source list INSIDE_NAT_ADDRESSES interface GigabitEthernet0/1 overload
!
IP access-list standard INSIDE_NAT_ADDRESSES
permit 192.168.1.0 0.0.0.255
permit 192.168.2.0 0.0.0.255
IP access-list standard SSH_MGMT
permit 192.168.1.0 0.0.0.255
permit 207.210.0.0 0.0.255.255
!
IP extended ACL-WAN_INTERFACE access list
deny udp any any eq snmp
TCP refuse any any eq field
TCP refuse any any eq echo
TCP refuse any any day eq
TCP refuse any any eq chargen
TCP refuse any any eq telnet
TCP refuse any any eq finger
deny udp any any eq field
deny ip 127.0.0.0 0.255.255.255 everything
deny ip 192.168.0.0 0.0.255.255 everything
permit any any eq 443 tcp
allow an ip
!
exploitation forest esm config
NLS RESP-timeout 1
CPD cr id 1
!
!
!
!
!
!
!
control plan
!
!
!
!
profile MGCP default
!
!
!
!
!
access controller
Shutdown
!
!
!
Line con 0
exec-timeout 0 0
Synchronous recording
line to 0
exec-timeout 0 0
Synchronous recording
line vty 0 4
exec-timeout 0 0
Synchronous recording
entry ssh transport
line vty 5 15
exec-timeout 0 0
Synchronous recording
entry ssh transport
!
Scheduler allocate 20000 1000
!
Gateway Gateway-WebVPN-Cisco WebVPN
IP interface GigabitEthernet0/1 port 443
SSL rc4 - md5 encryption
SSL trustpoint TRUSTPOINT-MY
development
!
WebVPN install svc flash:/webvpn/anyconnect-linux-3.1.03103-k9.pkg sequence 1
!
WebVPN context Cisco WebVPN
title "Firewall.cx WebVPN - powered by Cisco"
SSL authentication check all
!
list of URLS "rewrite".
!
ACL "ssl - acl.
ip permit 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
permit ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0
Licensing ip 192.168.0.0 255.255.0.0 192.168.0.0 255.255.0.0
!
login message "Cisco Secure WebVPN"
!
webvpnpolicy political group
functions required svc
filter tunnel ssl - acl
SVC-pool of addresses 'WEBVPN-POOL' netmask 255.255.255.0
generate a new key SVC new-tunnel method
SVC split include 192.168.1.0 255.255.255.0
Group Policy - by default-webvpnpolicy
AAA authentication list sslvpn
Gateway Cisco WebVPN bridge
Max-users 5
development
!
endGateway of last resort is #. ###. ###. # network 0.0.0.0
S * 0.0.0.0/0 [254/0] via #. ###. ###.1
(###ISP))) is divided into subnets, subnets 1
S (# #ISP #) [254/0] via (# publicgateway #) GigabitEthernet0/1
###.###.0.0/16 is variably divided into subnets, 2 subnets, 2 masks
C ###.###.###.0/23 is directly connected, GigabitEthernet0/1
The ###.###.###.###/32 is directly connected, GigabitEthernet0/1
192.168.1.0/24 is variably divided into subnets, 2 subnets, 2 masks
C 192.168.1.0/24 is directly connected, GigabitEthernet0/0
The 192.168.1.254/32 is directly connected, GigabitEthernet0/0
192.168.2.0/32 is divided into subnets, subnets 1
S 192.168.2.100 [0/0] via 0.0.0.0, Virtual Network1can you try to disable the FW on your internal lan hosts and then try and ping from users of vpn client
-
Cannot type 'functions' without client Anyconnect VPN setup
Hi I am trying set Anyconnect VPN client based on Cisco documents below. There is a command like below. When I typed 'function', I can't enter. Can anyone give me some suggestions? Thank you.
internal GroupPolicy1 group strategy
attributes of Group Policy GroupPolicy1
Protocol-tunnel-VPN IPSec l2tp ipsec webvpn
WebVPN
functions entry url file-access file-exploration of the mapi port forward files filter entry
HTTP-proxy download automatic citrixhttp://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...
ASA-recent versions, it is configured without the keyword "functions":
asa(config-group-policy)# webvpn asa(config-group-webvpn)# ? Group-policy WebVPN commands: ... file-browsing Allow browsing for file servers and shares file-entry Allow user entry of file server names to access filter Configure the name of the webtype access-list ... port-forward Configure the name of the Port Forwarding applet and auto-download options ... url-entry Control the ability of the user to enter any HTTP/HTTPS URL url-list Configure a list of WebVPN servers/URLs
-
Can not type 'url-list' without client Anyconnect VPN setup
Hi I am trying set Anyconnect VPN client based on Cisco documents below. There is a command like below. When I typed 'url-list', I can't enter.
Here is example of Cisco:
WebVPN
allow outside
list of URLS ServerList "WSHAWLAP" cifs://10.2.2.2 1
list of URLS ServerList "FOCUS_SRV_1" https://10.2.2.3 2
list of URLS ServerList "FOCUS_SRV_2" http://10.2.2.4 3Here's my ASA:
VPNFW-70/PRI/Act(config-WebVPN) # url -?
set up the mode commands/options:
URL-block url-url-cache serverMy ASA has no choice of the list of URLs when you type '?
Can anyone give me some suggestions? Thank you.
http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...
Hello
In the 7.x code all customizations without client was included in the running configuration.
However, referring to this document from cisco:- http://goo.gl/XRkrcO, you can see that this command has been deprecated in 8.X ASA codes.The best way to configure the bookmarks will use the ASDM or create them on a server and then bring import them to ASA.
Why we can not create bookmarks CLI?
With the introduction of 8.x many more options have been added, allowing greater flexibility. These new options would make the running configuration passes, so they were moved into separate xml files. Indeed, it eliminated the ability to configure a list of bookmark via the CLI.
For more information on this discussion, please refer to this thread: -.
https://supportforums.Cisco.com/discussion/11010546/how-do-i-create-URL-bookmark-WebVPN-Portal-CLIKind regards
Dinesh MoudgilPS Please rate helpful messages.
-
Setup for use with Cisco Anyconnect VPN IPsec
So, I had trouble setting up VPN on our ASA 5510. I would use IPsec VPN so that we don't have to worry about licensing issues, but what I have read you can do with and always use Cisco Anyconnect. My knowledge on how to set up VPN especially in iOS version 8.4 is limited, so I've been using a combination of command line and ASDM.
I am finally able to connect from a remote location, but once I log in, nothing else works. What I've read, you can use IPsec for client-to-lan connections. I use a pre-shared for this. Documentation is limited on what should happen after have connected you? Shouldn't be able to local access on the vpn connection computers? I'm trying to implement work. If I have VPN from home, should not be able to access all of the resources at work? According to me, because I used the command-line as ASDM I confused some of the configuration. In addition, I think that some of the default policies are confused me too. So I probably need a lot of help. Here is my current setup with the changed IP address and other things that are not related to deleted VPN.
NOTE: We are still testing this ASA and is not in production.
Any help you can give me is greatly appreciated.
ASA Version 8.4 (2)
!
ASA host name
domain.com domain name
!
interface Ethernet0/0
nameif inside
security-level 100
the IP 192.168.0.1 255.255.255.0
!
interface Ethernet0/1
nameif outside
security-level 0
IP 50.1.1.225 255.255.255.0
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
No nameif
security-level 100
IP 192.168.1.1 255.255.255.0
!
boot system Disk0: / asa842 - k8.bin
passive FTP mode
DNS domain-lookup outside
DNS server-group DefaultDNS
!
permit same-security-traffic intra-interface
!
network of the NETWORK_OBJ_192.168.0.224_27 object
subnet 192.168.0.224 255.255.255.224
!
object-group service VPN
ESP service object
the purpose of the tcp destination eq ssh service
the purpose of the tcp destination eq https service
the purpose of the service udp destination eq 443
the destination eq isakmp udp service object
!
allowed IP extended ip access list a whole
!
mask 192.168.0.225 - 192.168.0.250 255.255.255.0 IP local pool VPNPool
no failover
failover time-out period - 1
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 645.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source any any static destination NETWORK_OBJ_192.168.0.224_27 NETWORK_OBJ_192.168.0.224_27 non-proxy-arp-search to itinerary
!
the object of the LAN network
NAT dynamic interface (indoor, outdoor)
Access-group outside_in in external interface
Route outside 0.0.0.0 0.0.0.0 50.1.1.250 1
Sysopt noproxyarp inside
Sysopt noproxyarp outdoors
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint ASDM_TrustPoint0
registration auto
name of the object CN = ASA
Configure CRL
crypto ca server
Shutdown
string encryption ca ASDM_TrustPoint0 certificates
certificate d2c18c4e
864886f7 0d06092a c18c4e30 308201f3 3082015c a0030201 d 020204 2 0d 010105
0500303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609
02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109
3131 31303036 31393133 31365a 17 323131 30303331 39313331 0d 170d 6f6d301e
365a303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609
02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109
6f6d3081 9f300d06 092 has 8648 86f70d01 01010500 03818d b 30818902-00-818100-2
8acbe1f4 5aa19dc5 d3379bf0 f0e1177d 79b2b7cf cc6b4623 d1d97d4c 53c9643b
37f32caf b13b5205 d24457f2 b5d674cb 399f86d0 e6c3335f 031d54f4 d6ca246c
234b32b2 b3ad2bf6 e3f824c0 95bada06 f5173ad2 329c28f8 20daaccf 04c 51782
3ca319d0 d5d415ca 36a9eaff f9a7cf9c f7d5e6cc 5f7a3412 98e71de8 37150f02
03010001 300 d 0609 2a 864886 f70d0101 05050003 8181009d d2d4228d 381112a 1
cfd05ec1 0f51a828 0748172e 3ff7b480 26c197f5 fd07dd49 01cd9db6 9152c4dc
18d0f452 50f5d0f5 4a8279c4 4c1505f9 f5e691cc 59173dd1 7b86de4f 4e804ac6
beb342d1 f2db1d1f 878bb086 981536cf f4094dbf 36c5371f e1a0db0a 75685bef
af72e31f a1c4a892 d0acc618 888b53d1 9b 888669 70e398
quit smoking
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 activate out of service the customer port 443
Crypto ikev2 access remote trustpoint ASDM_TrustPoint0
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 10
Console timeout 0
management-access inside
SSL-trust outside ASDM_TrustPoint0 point
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
AnyConnect image disk0:/anyconnect-linux-2.5.2014-k9.pkg 2
AnyConnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 3
profiles of AnyConnect VPN disk0: / devpn.xml
AnyConnect enable
tunnel-group-list activate
internal VPN group policy
attributes of VPN group policy
value of server WINS 50.1.1.17 50.1.1.18
value of 50.1.1.17 DNS server 50.1.1.18
Ikev1 VPN-tunnel-Protocol, l2tp ipsec ikev2 ssl-client
digitalextremes.com value by default-field
WebVPN
value of AnyConnect VPN type user profiles
always-on-vpn-profile setting
privilege of xxxxxxxxx encrypted password username administrator 15
VPN1 xxxxxxxxx encrypted password username
VPN Tunnel-group type remote access
General-attributes of VPN Tunnel-group
address (inside) VPNPool pool
address pool VPNPool
LOCAL authority-server-group
Group Policy - by default-VPN
VPN Tunnel-group webvpn-attributes
enable VPN group-alias
Group-tunnel VPN ipsec-attributes
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
class-map ips
corresponds to the IP access list
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the http
class ips
IPS inline help
class class by default
Statistical accounting of user
I would recommend buy AnyConnect Essentials. The cost of the license is nominal - list of US $150 for the 5510. (piece number L-ASA-AC-E-5510 =)
Meawwhile you can use the Cisco VPN client inherited with IKEv1 IPSec remote access VPN using profiles *.pcf.
I believe you can also use the client Anyconnect client SSL or DTLS transport access remotely (non-IPsec) without having to buy the license Anyconnect Essentials for your ASA focus.
As an aside, note that if you want to use AnyConnect Mobile (e.g. for iPhone, iPad, Android, Blackberry etc.clients) you will also get the additional license for it (L-ASA-AC-M-5510 =, also price US $150)
-
Cisco 1700 Setup as a hub for Cisco Anyconnect VPN
The complete configuration for the router is attached. Additional configuration includes forwarding port 443 (the two tcp/udp), udp 4500, udp 500 and udp 50 to 192.168.1.20.
Objective: Configure Cisco 1700 router as a VPN server, which a Cisco Anyconnect VPN client in. The VPN server is behind a NAT.
Question 1: The Cisco Anyconnect client pulls its set of configuration of the router? I just need to point to the correct IP address and hit connect and it will do the rest? If not, what additional client side configuration must be done? I noticed, it tries to connect on port 443 to my router, but I don't really know why and I know that my router is not listening on this port, so I know I'm missing something:-D.
Question 2: What are the features specifically include easy vpn server? I am confused as to exactly what it is. From what I can tell when you configure easy vpn server you simply set up a regular VPN.
Question 3: Cisco Easy VPN remote has something to do with Cisco Anyconnect or they are completely distinct?
Sorry for the newbie questions. It's really hard to understand the different systems and features on it and most of the examples I found dealt with the VPN router to router rather than configurations just for computers of end users, but I'll be the first to admit that I am new on this hahaha.
Thanks for your help.
PS: Any comment on the misconfigs are welcome. I'm still trying to understand fully exactly what each command does.
Grant
Grant,
AnyConnect can do SSLVPN or IPsec (with IKEv2), ezvpn is all about IKEv1, it won't work.
There (part 3) customers who will be able to connect to ezvpn, as well as the former customer Cisco VPN, but AC is not.
BTW... it's not 50/UDP, this is IP protocol 50 (or sometimes 51) - ESP (or AH).
You don't have TCP and UDP 443 for IPsec, but you may need them for SSL.
And seriously... series of 1700? Wow, this is a 'retro' kit :-) Support ended 6 years ago.
M.
-
ASA Anyconnect VPN do not work or download the VPN client
I have a Cisco ASA 5505 that I try to configure anyconnect VPN and thought, I've changed my setup several times but trying to access my static public IP address of the external IP address to download the image, I am not able to. Also when I do a package tracer I see he has been ignored through the acl when the packets from side to the ASA via port 443, it drops because of the ACL. My DMZ so will he look like something trying to access the ASA via the VPN's going to port 443. Here is my config
XXXX # sh run
: Saved
:
ASA Version 8.4 (3)
!
hostname XXXX
search for domain name
activate pFTzVNrKdD9x5rhT encrypted password
zPBAmb8krxlXh.CH encrypted passwd
names of
!
interface Ethernet0/0
Outside-interface description
switchport access vlan 20
!
interface Ethernet0/1
Uplink DMZ description
switchport access vlan 30
!
interface Ethernet0/2
switchport access vlan 10
!
interface Ethernet0/3
switchport access vlan 10
!
interface Ethernet0/4
Ganymede + ID description
switchport access vlan 10
switchport monitor Ethernet0/0
!
interface Ethernet0/5
switchport access vlan 10
!
interface Ethernet0/6
switchport access vlan 10
!
interface Ethernet0/7
Description Wireless_AP_Loft
switchport access vlan 10
!
interface Vlan10
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Vlan20
nameif outside
security-level 0
IP address x.x.x.249 255.255.255.248
!
Vlan30 interface
no interface before Vlan10
nameif dmz
security-level 50
IP 172.16.30.1 255.255.255.0
!
boot system Disk0: / asa843 - k8.bin
passive FTP mode
DNS lookup field inside
DNS domain-lookup outside
DNS domain-lookup dmz
DNS server-group DefaultDNS
Name-Server 8.8.8.8
Server name 8.8.4.4
search for domain name
network obj_any1 object
subnet 0.0.0.0 0.0.0.0
network of the Webserver_DMZ object
Home 172.16.30.8
network of the Mailserver_DMZ object
Home 172.16.30.7
the object DMZ network
172.16.30.0 subnet 255.255.255.0
network of the FTPserver_DMZ object
Home 172.16.30.9
network of the Public-IP-subnet object
subnet x.x.x.248 255.255.255.248
network of the FTPserver object
Home 172.16.30.8
network of the object inside
192.168.10.0 subnet 255.255.255.0
network of the VPN_SSL object
10.101.4.0 subnet 255.255.255.0
outside_in list extended access permit tcp any newspaper object Mailserver_DMZ eq www
outside_in list extended access permit tcp any newspaper EQ 587 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper SMTP object Mailserver_DMZ eq
outside_in list extended access permit tcp any newspaper of the Mailserver_DMZ eq pop3 object
outside_in list extended access permit tcp any newspaper EQ 2525 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper of the Mailserver_DMZ eq imap4 object
outside_in list extended access permit tcp any newspaper EQ 465 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper EQ 993 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper EQ 995 object Mailserver_DMZ
outside_in list extended access permit tcp any newspaper EQ 5901 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper Mailserver_DMZ eq https object
Note access list ACL for VPN Tunnel from Split vpn_SplitTunnel
vpn_SplitTunnel list standard access allowed 192.168.10.0 255.255.255.0
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer to 8192
logging trap warnings
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 dmz
local pool VPN_SSL 10.101.4.1 - 10.101.4.4 255.255.255.0 IP mask
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 647.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source inside inside static destination VPN_SSL VPN_SSL
NAT (exterior, Interior) static source VPN_SSL VPN_SSL
!
network obj_any1 object
NAT static interface (indoor, outdoor)
network of the Webserver_DMZ object
NAT (dmz, outside) static x.x.x.250
network of the Mailserver_DMZ object
NAT (dmz, outside) static x.x.x.. 251
the object DMZ network
NAT (dmz, outside) static interface
Access-group outside_in in external interface
Route outside 0.0.0.0 0.0.0.0 x.x.x.254 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol Ganymede HNIC +.
AAA-server host 192.168.10.2 HNIC (inside)
Timeout 60
key *.
identity of the user by default-domain LOCAL
Console HTTP authentication AAA HNIC
AAA console HNIC ssh authentication
Console AAA authentication telnet HNIC
AAA authentication secure-http-client
http 192.168.10.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ca trustpoint localtrust
registration auto
Configure CRL
Crypto ca trustpoint VPN_Articulate2day
registration auto
name of the object CN = vpn.articulate2day.com
sslvpnkey key pair
Configure CRL
Telnet 192.168.10.0 255.255.255.0 inside
Telnet timeout 30
SSH 192.168.10.0 255.255.255.0 inside
SSH timeout 15
SSH version 2
Console timeout 0
No vpn-addr-assign aaaDHCP-client update dns
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd outside auto_config
!
dhcpd address 192.168.10.100 - 192.168.10.150 inside
dhcpd allow inside
!
dhcpd address dmz 172.16.30.20 - 172.16.30.23
dhcpd enable dmz
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
authenticate the NTP
NTP server 192.168.10.2
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-linux-64-3.1.06079-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
internal VPN_SSL group policy
VPN_SSL group policy attributes
value of server DNS 8.8.8.8
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpn_SplitTunnel
the address value VPN_SSL pools
WebVPN
activate AnyConnect ssl dtls
AnyConnect Dungeon-Installer installed
AnyConnect ssl keepalive 15
AnyConnect ssl deflate compression
AnyConnect ask enable
ronmitch50 spn1SehCw8TvCzu7 encrypted password username
username ronmitch50 attributes
type of remote access service
type tunnel-group VPN_SSL_Clients remote access
attributes global-tunnel-group VPN_SSL_Clients
address VPN_SSL pool
Group Policy - by default-VPN_SSL
tunnel-group VPN_SSL_Clients webvpn-attributes
enable VPNSSL_GNS3 group-alias
type tunnel-group VPN_SSL remote access
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect esmtp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:d41d8cd98f00b204e9800998ecf8427e
: endXXXX #.
You do not have this configuration:
object network DMZ nat (dmz,outside) static interface
Try and take (or delete):
object network DMZ nat (dmz,outside) dynamic interface
-
Lock the AnyConnect VPN with broader access list
I'm trying to lock my AnyConnect VPN interface. I use the split tunneling. I want only to http tunnel traffic to an external http server we have and ftp to another external server behave. I don't want anything else through the tunnel or anywhere else allowed on our network. My current setup, I can connect to the vpn and the servers ping external ip address, but not by name. I can also not navigate anywhere else while I'm connected. It is not imperative for me to navigate anywhere else, when you are connected, but I need to allow only access specified above.
Configuration:
attributes Anyconnect-group policy
VPN-tunnel-Protocol svc webvpn
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list WebAccessVPN
WebVPN
list of URLS no
SVC request to enable default webvpn
WebAccessVPN list extended access allow icmp disable any newspaper host FTP - EXT object-group Ping_and_Trace
External FTP FTP access WebAccessVPN-list comment
WebAccessVPN list extended access permitted tcp disable no matter what newspaper to host FTP - EXT object-group DM_INLINE_TCP_2
WebAccessVPN list extended access allow icmp disable any newspaper host LICENSING-EXT object-group Ping_and_Trace
WebAccessVPN list extended access allowed object-group TCPUDP any LICENSING-EXT eq www log disable host
WebAccessVPN list extended access deny ip any object-group DM_INLINE_NETWORK_1
You can use the vpn filter under the attributes of political group. In the vpn-filter, you can reference the access list you created.
-
ASA5505 SSL AnyConnect VPN and NAT Reverse Path failure
I worked on it for a while and just have not found a solution yet.
I have a Cisco ASA5505 Setup at home and I try to use the AnyConnect VPN client to it. I followed the example of ASA 8.x split Tunnel but still miss me something.
My home network is 10.170.x.x and I install the VPN address to 10.170.13.x pool I have a Windows workstation running at 10.170.0.6, printers 10.170.0.20 and 21 and inside the router itself is 10.170.0.1
I can connect from the outside and am assigned an IP address of 10.170.13.10, but when I try to access network resources via ICMP or open a web page, the newspaper of the ASDM shows a bunch of this:
5. January 27, 2010 | 10: 33:37 | 305013 | 10.170.255.255 | 137. Asymmetrical NAT rules matched for flows forward and backward; Connection for udp src outside:10.170.13.10/137 dst inside:10.170.255.255/137 refused due to path failure reverse that of NAT
5. January 27, 2010 | 10: 33:36 | 305013 | 10.170.255.255 | 137. Asymmetrical NAT rules matched for flows forward and backward; Connection for udp src outside:10.170.13.10/137 dst inside:10.170.255.255/137 refused due to path failure reverse that of NAT
5. January 27, 2010 | 10: 33: 35 | 305013 | 10.170.255.255 | 137. Asymmetrical NAT rules matched for flows forward and backward; Connection for udp src outside:10.170.13.10/137 dst inside:10.170.255.255/137 refused due to path failure reverse that of NAT
5. January 27, 2010 | 10: 33:34 | 305013 | 10.170.0.6 | Asymmetrical NAT rules matched for flows forward and backward; Connection for icmp src, dst outside: 10.170.13.10 inside: 10.170.0.6 (type 8, code 0) rejected due to the failure of reverse path of NAT
5. January 27, 2010 | 10:33:30 | 305013 | 10.170.255.255 | 137. Asymmetrical NAT rules matched for flows forward and backward; Connection for udp src outside:10.170.13.10/137 dst inside:10.170.255.255/137 refused due to path failure reverse that of NAT
5. January 27, 2010 | 10: 33:29 | 305013 | 10.170.255.255 | 137. Asymmetrical NAT rules matched for flows forward and backward; Connection for udp src outside:10.170.13.10/137 dst inside:10.170.255.255/137 refused due to path failure reverse that of NAT
5. January 27, 2010 | 10: 33:28 | 305013 | 10.170.255.255 | 137. Asymmetrical NAT rules matched for flows forward and backward; Connection for udp src outside:10.170.13.10/137 dst inside:10.170.255.255/137 refused due to path failure reverse that of NAT
5. January 27, 2010 | 10: 33:28 | 305013 | 10.170.0.6 | Asymmetrical NAT rules matched for flows forward and backward; Connection for icmp src, dst outside: 10.170.13.10 inside: 10.170.0.6 (type 8, code 0) rejected due to the failure of reverse path of NAT
5. January 27, 2010 | 10:33:23 | 305013 | 10.170.0.6 | Asymmetrical NAT rules matched for flows forward and backward; Connection for icmp src, dst outside: 10.170.13.10 inside: 10.170.0.6 (type 8, code 0) rejected due to the failure of reverse path of NAT
5. January 27, 2010 | 10:33:17 | 305013 | 10.170.0.6 | Asymmetrical NAT rules matched for flows forward and backward; Connection for icmp src, dst outside: 10.170.13.10 inside: 10.170.0.6 (type 8, code 0) rejected due to the failure of reverse path of NAT
5. January 27, 2010 | 10: 33: 13 | 305013 | 10.170.0.6 | Asymmetrical NAT rules matched for flows forward and backward; Connection for icmp src, dst outside: 10.170.13.10 inside: 10.170.0.6 (type 8, code 0) rejected due to the failure of reverse path of NAT
5. January 27, 2010 | 10:33:07 | 305013 | 10.170.0.6 | Asymmetrical NAT rules matched for flows forward and backward; Connection for icmp src, dst outside: 10.170.13.10 inside: 10.170.0.6 (type 8, code 0) rejected due to the failure of reverse path of NATI tried several things with NAT, but were not able to go beyond that. Does anyone mind looking at my config running and help me with this? Thanks a bunch!
-Tim
Couple to check points.
name 10.17.13.0 UFP-VPN-pool looks like it should be the name 10.170.13.0 UFP-VPN-pool
inside_nat0_outbound to access extended list ip allow list zero 255.255.0.0 255.255.255.0 UFP-VPN-pool
Looks like that one
inside_nat0_outbound to list extended ip access list zero UFP-VPN-pool 255.255.255.0 255.255.255.0 allow
-
I installed an ASA-5515 with 9.1 2. I have Setup with users using AnyConnect VPN. Everything works fine. I have now a few new requirements that I don't know how to set up or if they are even possible.
(1) can I configure the VPN if a user can choose whether they use split tunnel. We have a couple of engineers who are in China and need to use the VPN so that in addition to the normal access, which can use the VPN for regular access to the Internet without going through the filters of China. I think it means that I have to also install a PIN in the SAA. But I want to only do this when necessary.
(2) can I configure the VPN and it can work to our network of comments that can be found on the same ASA.
Thank you... Jim
Jim,
My info can be turned off by about two years, but...
AD1. Would need to set up a separate tunnel-group or assign different parameters via DAP/RADIUS/that it is, including a different pool of IP addresses if you want to do hair pinning for a portion of the traffic. It's probably the "easiest".
AD2. A few challenges. Yes, you can activate service anyconnect on multiple interface, not only on the outside. Think traffic well. Because of the choices architects of ASA (at least they were in place two years back) you will not be able to communicate _with_ ASA on a different interface you are currently, with the exception of access management. If you activate the anyconnect on the front guest network interface service. This approach also comes with a DNS challenge, when it is called network of comments for the DNS record of myasa.mycompany.tld, you must return the IP network hosts.
[Hope that makes sense:]
M.
-
AnyConnect VPN for Cisco ASA 5505 refused connections
I'm trying to set up my Cisco 5505 with AnyConnect VPN client VPN access. Here is the relevant information of my config:
interface Vlan2
mac-address xxxx.xxxx.xxxx
nameif outside
security-level 0
ip address A.A.A.A 255.255.255.240
!
access-list outside_access_in extended permit tcp any host C.C.C.C eq pptp
access-list outside_access_in extended permit tcp any host C.C.C.C eq https
access-list outside_access_in extended permit tcp any host C.C.C.C eq ftp
access-list outside_access_in extended permit tcp any host C.C.C.D eq https
access-list outside_access_in extended permit tcp any host C.C.C.D eq ftp
access-list outside_access_in extended permit tcp any host C.C.C.D eq www
access-list outside_access_in extended permit tcp any host C.C.C.C eq smtp
access-list outside_access_in extended permit icmp any any
access-list outside_access_in extended permit tcp any host C.C.C.D eq ssh
access-list outside_access_in extended permit tcp any host C.C.C.D eq 8080
access-list outside_access_in extended permit gre any host C.C.C.C
access-list outside_access_out extended permit ip any any
access-list inside_access_in extended permit ip any any
access-list inside_access_in extended permit ip any interface outside
access-list inside_access_out extended permit ip any anyaccess-group inside_access_in in interface inside
access-group inside_access_out out interface inside
access-group outside_access_in in interface outside
access-group outside_access_out out interface outsidewebvpn
enable inside
enable outside
svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1
svc enablegroup-policy DfltGrpPolicy attributes
dns-server value X.X.X.X
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
split-tunnel-policy tunnelspecified
split-tunnel-network-list value
address-pools value palm
webvpn
svc rekey time 30
svc rekey method ssl
svc ask enable default webvpnpolicy-map global_policy
class inspection_default
inspect pptp
inspect http
inspect icmp
inspect ftp
!When I try to connect, I get this error in the real-time log viewer:
TCP access denied by ACL from X.X.X.X/57356 to outside:A.A.A.A/443
Here are the details of the license:
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
SSL VPN Peers : 2
Total VPN Peers : 10
Dual ISPs : Disabled
VLAN Trunk Ports : 0
Shared License : Disabled
AnyConnect for Mobile : Disabled
AnyConnect for Linksys phone : Disabled
AnyConnect Essentials : Disabled
Advanced Endpoint Assessment : Disabled
UC Phone Proxy Sessions : 2
Total UC Proxy Sessions : 2
Botnet Traffic Filter : DisabledThis platform has a Base license.
Can someone tell me what I am doing wrong or what access list I'm missing?
I have two Cisco ASA 5510 firewall with a similar setup configuration and the AnyConnect SSL VPN works great.
Hi Matt,
You are probably landing on the tunnel-group by default - you will need to indicate which group to connect to the client. This can be done in different ways - I see that you already have a defined group aliases, but to be able to use that you must configure:
WebVPN
tunnel-group-list activate
Alternatively, if you have only a single group, you can add 'group-url https://yourasa.yourcompany.com/ permit' to the webvpn attributes tunnel-group.
HTH
Herbert
-
Why can't save my new 6 s of a 5 on the cloud without setup assistant, phone was at the verizon store installation.
This error message do you receive? is a new feature in iOS 9.3.1?
-
AnyConnect VPN and HP Office Jet Pro 8500 A910
I can print from my laptop IBM T400 running Windows 7 64 bit. However, when I log in work AnyConnect VPN, I can't print. He says that the printer is disconnected from the network, even if it is connected. IT support at work said he can't change or adjust the VPN settings. The only way I can print is to disconnect from the VPN. Is this what I can adjust on the software of the printer or the printer itself?
Hello
To be able to print on the local network when you are connected to a network remote VPN might be possible by changing the VPN split tunneling configuration.
However, it is depands on the VPN features and cannot be authorized because of the security requirements of your IT Department.
Anyway, there is no way to configure such a thing by the printer or the printer software... It is directly affected by the configuration of the network and therefore require to modify VPN settings.
Kind regards
Shlomi
-
Cisco AnyConnect VPN Client maintains reconnection
Hello
We have recently installed an ASA5505 and activated the VPN access.
Two of my colleagues have no problems connecting to the VPN using Cisco AnyConnect VPN Client, but I do.
I am still disconnected after a few seconds with the message:
"A VPN reconnect gave rise to different configuration settings. VPN network interface is to be reset. Applications using the private network may be required to restart. »
Cisco AnyConnect VPN Client Version 2.5.2019
I work with Windows 7 but the same thing happens when I try to connect using my computer that is running Windows Vista.
My colleagues also using Win7
I also tried to disable the Windows Firewall.
Any help would be appreciated.
Best regards
Peter
TAC has been able to solve the problem. For webvpn mtu changed default from 1406 to 1200.
Not sure why 2 other ASAs we work very well otherwise though!
WebVPN
SVC mtu 1200 -
IOS anyconnect vpn group lock and user restrictions
Dear Experts,
I now have two questions about cisco IOS vpn on ISR G2:
1 is it possible to lock user group in IOS anyconnect VPN we can do in ASA? If so, can someone share the steps for her?
2 - a customer wishes to restrict the anyconnect user login as it might turn the connection to the user on request. That is to say whenever the user wants to connect via vpn to ask the administrator to allow connection. can we do without deleting the username and create again?
the other may be on ASA or IOS.
Please see this guide:
http://www.Cisco.com/c/en/us/support/docs/security/iOS-easy-VPN/117634-c...
As he points out, "for the Cisco IOS group-lock and the ipsec: use vpn-group, it only works for IPSec (the easy VPN server)." In order to group-lock specific users in specific contexts of WebVPN (and strategies Group attached), authentication domains should be used. »
If you lock a user to a policy that authenticates, but does provide real access permissions (say an ACL that blocks all traffic to the private network) then you have essentially made their ability to non-functional connection.
If you use an external AAA server (for example, RADIUS or LDAP), then you can move in and out of the group which is authorized without disable VPN access / delete their account altogether.
Maybe you are looking for
-
Is webcake an authorized by modzilla upgrade I get notice to improve firefox expired
When I open the browser one notice in the top corner of the display indicate that obsolete modzilla should update.Then this webcake download starts does not resemble any Modzilla upgrade I did
-
Vista Service Pack 1 is not available for installation
Original title: Vista Service Pack 1 I had started to install vista sp1 and cancelled the installation. Now, I want to install it. It is listed under "story updates" as cancelled but not available under updates. How can I reinstall Service Pack 1 of
-
Outlook Express seems to set font sizes when the recipient receives the e-mail I sent.
Hi again. I should have added to my query on Outlook Express is shrinking the font size of my e-mail in transit that he can be a factor of parameters of beneficiaries, because: a) they seem to get normal size of other people's mail, and IT was tiny
-
problem with thinkpad x220i and rangeplus router wrt 110
Just got a new thinkpad x220i and whenever I try to connect to my wireless network, accidents of router and my cable modem seems to descend with her and the internet connection is also lost. I need to restart the whole nine yards. I got this router -
-
Print PDF caused the failure of the print spooler
I have been all over these blogs, and nobody has the answer. I had no problem and then today when I tried to print a pdf file, everything went haywire. I can not print, I can't remove and reinstall my printer, I can't restart the print spooler (it tr