ap1231g

Similar Questions

• Impossible to Aironet AP1231G

  I'm trying to update my Aironet AP1231G IOS. It is running IOS version 12.2 (3) JA ED. I tried many upgrades to the matching under the Aironet 1200 and 1230 categories versions but they do not work. I get the error "ERROR. The software update was interrupted and could not be completed." I tried via tftp, http and via command line. Someone knows what's the problem? Any help would be great. Thank you.

  Assign an ip address in the same subnet as the AP is in and place the connection in the same vlan as the AP

• AIR-AP1231G-A-K9

  Hello

  If the customer buys Aironet AIR-AP1231G-A-K9 done it comes with built-in or external antenna as well as the product or they need to get the antenna separately.

  Please clearify the same.

  In the Cisco Configuration tool also creaton to purchase the antenna separately.

  Concerning

  Rama

  Please find details as mentioned below

  http://www.Cisco.com/en/us/prod/collateral/wireless/ps7183/ps469/product_data_sheet09186a008022b11b_ps6521_Products_Data_Sheet.html

  Kind regards

• AP1231G SSID broadcasts do not [config posted]

  I recently bought a set of access points AP1231G that have been pre-configured as root and nonroot bridges. Initially, I couldn't have a SSID will be displayed, thinking that I may have missed something that has been preconfigured I wiped the config and started from scratch. I went through several guides configuration to enable WPA with open authentication, but have had no success with the SSID is broadcast, and still less connecting to the AP.

  Any help is greatly appreciated. Config below:

  version 12.3
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  encryption password service
  !
  host ap name
  !
  enable secret 5 $1$ lgoW$ zk7dfGkGLlZiOQuRFsxfV.
  !
  IP subnet zero
  !
  !
  No aaa new-model
  dot11 syslog
  !
  dot11 ssid MW2
  open authentication
  authentication wpa key management
  Comments-mode
  WPA - psk ascii 7 02050D4808090C285F4D06
  !
  !
  !
  username password Cisco 7 02250D 480809
  !
  Bridge IRB
  !
  !
  interface Dot11Radio0
  no ip address
  no ip route cache
  !
  encryption ciphers aes - ccm mode
  !
  SSID MW2
  !
  base speed - 1.0 2.0 basic basic-5, 5 6.0 9.0 basic-11, 0 12.0 18.0 24.0 36.0 48.0 54.0
  root of station-role
  Bridge-Group 1
  Bridge-group subscriber-loop-control 1
  Bridge-Group 1 block-unknown-source
  No source of bridge-Group 1-learning
  unicast bridge-Group 1-floods
  Bridge-Group 1 covering-disabled people
  !
  interface FastEthernet0
  no ip address
  no ip route cache
  automatic duplex
  automatic speed
  Bridge-Group 1
  No source of bridge-Group 1-learning
  Bridge-Group 1 covering-disabled people
  !
  interface BVI1
  IP 10.81.220.5 255.255.255.0
  no ip route cache
  !
  IP http server
  no ip http secure server
  IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
  !
  output of the TFTP server
  1 channel ip bridge
  !
  !
  !
  Line con 0
  line vty 0 4
  local connection
  !
  end

  the antennas are connected?

  Concerning

  Surendra

• AIR-AP1231G and PoE

  Evening,

  I have a number of AIR-AP1231G scattered in my factory. All are fed power inline injectors and are working properly.

  I am wanting to buy a number of PoE switches that will have the task off the injectors inline for an easier game to the top.

  I bought a Cisco 300 Series 10 Max PoE Switch port, however the AIR-AP1231G won't start when you plug into the switch. No light on the switch or the AP.

  Oddly enough, I have an AP1242G AIR of what powers well without any problem of the switch.

  Is there any configuration, I need to do on the access point so that it can turn on from the switch? The datasheet of the switch indicates that it is 802.3af. I tried the access point on the 10MP models of 28 p of the 300 series and no go.

  Can someone tell me please in the right direction? I'm really lost and PoE is slightly beyond me at the minute.

  Hi Tim,.

  You are welcome

  Yes, it's worth a try. The 1230 is shown as it is supported.

  http://www.microsemi.com/PowerDsine/documentation/SelectionGuide/SelectionGuide.PDF

  See you soon!

  Rob

• Set up the AIR-AP1231G-A-K9 for WGB (IOS 12.4 JA (13d)

  Hello

  I'm trying to set up one of our extra 1231 AP as a workgroup bridge. The AP has been configured as a lightweight access point so I think maybe that's part of my question.

  It was the documentation that I found to do the config: http://cisco.com/en/US/docs/wireless/access_point/12.4_3g_JA/configuration/guide/s43hot.html

  However, I don't have the available commands that they list.

  Here is HS worm info:

  Cisco IOS software, C1200 software (C1200-K9W8-M), Version 12.4 (13d) JA, VERSION of the SOFTWARE (fc2)

  Technical support: http://www.cisco.com/techsupport

  Copyright (c) 1986-2008 by Cisco Systems, Inc.

  Last updated Saturday, February 8 08 17:24 by prod_rel_team

  SWN-e9-wh-01-SWAP #config t

  Enter configuration commands, one per line. End with CNTL/Z.

  SWN-e9-wh-01-SWAP (config) #int dot

  SWN-e9-wh-01-SWAP (config) #int dot11Radio 0

  SWN-e9-wh-01-SWAP(config-if) #stati?

  % Unrecognized command

  Is it not possible with the IOS and the AP I have?

  Hi Eric,.

  I'm just curious, did you convert the AP to IOS already?

  This can be converted to a standalone/stand alone AP you want;

  Here is a method of conversion;

  Returning to standalone Access Point

  You can convert an access point of the mode light return to autonomous mode by loading a Cisco IOS version that supports stand-alone mode (Cisco IOS release 12.3 (7) JA or earlier version). If the access point is associated with a controller, you can use the controller to load the version of Cisco IOS. If the access point is not associated with a controller, you can load the version of Cisco IOS using TFTP.

  By using a TFTP server to revert to a previous version

  Follow these steps to return mode LWAPP stand-alone mode by loading a version of Cisco IOS using a TFTP server:

  --------------------------------------------------------------------------------

  Step 1 the IP address of the computer on which the server software runs TFTP should range from 10.0.0.2 to 10.0.0.30.

  Step 2 make sure the PC contains the file access point (for example, c1200-k9w7 - tar.122 - 15.JA.tar for a 1200 Series access point) in the TFTP server folder and the TFTP server is activated.

  Step 3 Rename the access point image file in the folder of the TFTP server c1200-k9w7 - tar.default for a series of 1200 point, c1130-k9w7 - tar.default of access for a series of 1130 access point and c1240-k9w7 - tar.default for a series of 1240 access point.

  Step 4 connect the PC to the access point using an Ethernet category 5 cable (CAT5).

  Step 5 disconnect the power to the access point.

  Step 6 push the MODE button and hold the button while you reconnect power to the access point.

  Step 7 hold the MODE button until the status of the LED turns red (approximately 20 to 30 seconds), then release.

  Step 8 wait until restarting access point, as indicated by the LEDs become green followed the status LED flashes green.

  Step 9 after the access point reboots, reconfigure using the GUI or the CLI.

  I hope this helps!

  Rob

• Emission of Radio AIR-AP1231G-A-K9 power

  Hi experts,

  I have some of these WAP and they all high gain 8dbi antennas. I wonder if I need to adjust the 'local cck/ofdm power' to certain values to match the antenna gain for that to work the best. The radio works in b/g mode. This is the current configuration of the interface Dot11Radio0.

  interface Dot11Radio0
  no ip address
  no ip unreachable
  no ip route cache
  !
  SSID XXXXXX

  !
  base speed - 1.0 2.0 basic basic-5, 5 6.0 9.0 basic-11, 0 12.0 18.0 24.0 36.0 48.0 54.0
  no short preamble
  channel 2412
  root of station-role
  threshold RTS 2312
  antenna gain 8
  No dot11 extensions aironet
  Bridge-Group 1
  Bridge-group subscriber-loop-control 1
  Bridge-Group 1 protected Harbour
  Bridge-Group 1 block-unknown-source
  No source of bridge-Group 1-learning
  unicast bridge-Group 1-floods
  Bridge-Group 1 covering-disabled people
  end

  Also, I would be grateful if you can report a bad config under this interface. Thank you!

  Hello

  # You don't have to configure the power setting.  You can configure any desired power value, allowing AP to offset the gain of antenna to make sure that the TX power is wrong on the FCC regulation.

  Kind regards

  Manual

• Air-AP1200

  I'll order "AIR-AP1231G-E-K9" and requires external antennas. I need directlty antennas linked to this no wireless access point. "AIR-ANT4941" antinna is correct for this requirement. If it's the right choice, I have to order two "AIR-ANT4941" or one order can meet the requirement of two antinaas diversity.

  AIR-ANT4941 is the correct antenna, and Yes, you need to order 2 of them.

• Aironet 1200 series - power of the weak signal near AP

  I recently bought an access point of the Aironet 1200 (AIR-AP1231G-A-K9) series and the initial setup - IP configuration on the AP, the installer does a SSID and turn on the radio.

  I used my laptop to connect to the SSID that I created, but to my surprise the signal strength of my SSID was only 2 bars and sometimes 1 bar and I'm within 2 feet of the access point. However, the speed of connection/signal quality was varying between 24 Mbps and 36 Mbps.

  Why is the signal strength so low?

  Is is because I did not buy them with external antennas?

  I missed something during the initial Setup?

  Y at - it an option that I have change/fine adjust in the GUI to get the best signal strength?

  Help, please.

  "Is is because I did not buy them with external antennas?

  Yes, that's correct. There is no internal antennas on this model of AP.

  You need at least one, preferably two antennas of the same type for each radio. If you have the old 'A' radio with the paddle antenna, then you only need one or two antennas of radio 2.4 G.

  Good luck

  Scott

• The number of MAC address entries can manage a list of access (AIR1200)

  Hi all

  I had a few AP1231G accesspoint with a configured MAC filter.

  Now I'm curios if the access list has a limitation maximum mac address.

  At present, there are about 130 MAC address and the couple of clients sometimes struggling to connect.

  Any tips?

  Thank you

  Norbert

  I was referring to the size of autonomous AP database.

  The default size of the database of the controller is different according to the verion.

• Configure AP 1200 Series

  I have a question setting my AIR-AP1231G-E-K9 access point model. I'm not familiar with Cisco technology, but I can't be able to use the hyper terminal.

  Could someone help me configure my access through the hyper terminal point. I much appreciated for your help.

  Thank you very much

  Tauseef Ahmed

  Dubai, UNITED Arab Emirates

  Could any one help me to configure my access point through hyper terminal.
  

  This should be a two-in-one document.

  Key combinations standard break during password recovery

• Cisco 1231 join 2504 wlc

  All, Hy

  you have the following problem:

  Convert a Cisco 1231 with (used light update tool

  C1200 - rcvk9w8 - tar.124 - 21A .JA2 .tar). it worked, but now the AP issn can't join the wlc:

  AP with MAC 00:11:22:33.44:55 (AIR-AP1231G-E-K9) is unknown.

  * spamApTask0: 18:26:44.598 Oct 02: 00:13:c4:e7:ad:c5 connection find DTLS delete AP (172:16:22:11 / 19157)

  * spamApTask0: 18:26:44.598 Oct 02: 00:13:c4:e7:ad:c5 disconnect Ctrl-Capwap-DTLS session 0x14f3b038 for AP (172:16:22:11 / 19157)

  * spamApTask0: 18:26:44.598 Oct 02: 00:13:c4:e7:ad:c5 CAPWAP State: Dtls shoot

  * spamApTask0: 18:26:44.598 Oct 02: 00:13:c4:e7:ad:c5 DTLS keys for deleted successfully for AP 172.16.22.11 control plan

  * spamApTask0: 18:26:44.599 Oct 02: State 00:13:c4:e7:ad:c5 machine Manager: failed to process the msg = 3 State = 0 172.16.22.11:19157 type

  * spamApTask0: 18:26:44.599 Oct 02: 00:13:c4:e7:ad:c5 impossible to analyze packets 172.16.22.11:19157 CAPWAP

  * spamApTask0: 18:26:44.599 Oct 02: DTLS closed connection events receivedserver 00:13:c4:e7:ad:c5 (172:16:22:5 / 5246) client (172:16:22:11 / 19157)

  * spamApTask0: 18:26:44.599 Oct 02: 00:13:c4:e7:ad:c5 entry exists for AP (172:16:22:11 / 19157)

  * spamApTask0: 18:26:44.605 Oct 02: 00:13:c4:e7:ad:c5 entry no. AP exist in the temporary database for 172.16.22.11:19157

  (* spamApTask0: 18:26:44.606 Oct 02: 00:13:c4:e7:ad:c5 throw no - ClientHello Handshake or DTLS encrypted package to 172.16.22.11:19157) since DTLS session is not established

  No idea here? Thanks in advance!

  What code of the controller, you're on? 1200 is not supported after 7.0 code...

  Older aps, the year 1200 did not come with microphones. An SSC is created, you are sure that the SSC is enabled in the wlc and you have the SSC on the controller?

  http://www.Cisco.com/en/us/products/ps6366/products_configuration_example09186a00806a426c.shtml

  __________________________________________________________________________________________
  "Satisfaction does not come to know the solution, it is to know why." - Rosalind Franklin