APK Build - device ready for start-up

Similar Questions

• Now, Firefox is ready for me to start using?

  I just want to know if everything is ready for me to start to use firefox?

  What you mean? If you want to start using Firefox, here's a good place, start with Firefox – an overview of the main features

• The device, \Device\Harddisk2\D, is not ready for access yet.

  Event Viewer has many entries of error ID 15, which States:
  The device, \Device\Harddisk2\D, is not ready for access yet.

  What does that mean?  Is this an indication of imminent drive failure?

  Hello

  ·         Did you of recent changes to the computer before the show?

  Method 1: Check that all connectors (power and IDE) should be firmly fixed. Disconnect and reconnect to check.

  Method 2: As short-term solution, try to shut down the system, turn the power off, turn on the power and restart. If the device still does not work then it is probably a problem of material, the device or card/main controller card (or possibly the cable connection) will need to be replaced. If the device seems to work then this indicates a problem of software or firmware. Do not forget that the problem can recur again unless the root causes addressed.

  Method 3: Update the latest version of the device driver (if there is one).
  Check on the Web site of the vendor for a newer driver and if it is available then load it.

  Reference: http://support.microsoft.com/kb/283658

  Method 4: Enforcement Procedure in Windows XP check disk errors

  http://support.Microsoft.com/kb/315265

  CHKDSK warning:

  Important: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

• Vista: The device can not start (error Code 10) for a USB CDC device which works fine in XP

  I have a USB device 2.0 DCC which works very well under all of our Windows XP machines, but not based on Vista.  The device uses the usbser.sys driver and emulation of the virtual Comm Port.

  The text of the listing shows the same information on Xp and Vista, except under vista it shows no open pipes.  Shows Device Manager: device can not start (error Code 10).

  Using Vista I can't connect to the vista of CDC through concentrators or device to any other device wireless hub except for a Dlink Wireless hub, which has a layer of software between the CDC device and the PC.  With Xp, it all works very well on more than one PC, with Vista, there are questions.  I use the INF manufacturer provided for Vista, still no results.

  Any ideas on this would be greatly appreciated.

  Hi NuWaveDC,

  Thank you for taking the time to post on the Microsoft answers Forums.

  Please see the following article for an explanation of this error code 10.

  Explanation of error codes generated by Device Manager

  http://support.Microsoft.com/kb/310123

  Follow the steps listed for the error Code 10 see if this helps solve your problem or not.

  Please post back to let us know if this information was useful or not, so that we can help you if need be.

  Robyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• When starts to Flash builder support export for Windows Mobile OS?

  When starts to Flash builder support export for Windows Mobile OS?

  I think that VB was confused by call you 'Windows Mobile', such as Windows Mobile is MS is obsolete, abandoned Mobile OS for the era pre-iPhone with a stylus and all that, I guess that you probably meant 'Windows Phone' / Windows 8 Metro UI / RT of Windows, the new iPhone, as MS Mobile OS.

  See this thread: http://forums.adobe.com/message/4526684#4526684

• RT: Remote desktop says "cannot find a device suitable for C drive.

  Hello

  There is a french position on exactly the same topic, but I can't apply the solution given here.

  My problem is this: I have a remote, ready to work as a target RT Office. It has been verified for compatibility, the hard drive has been formatted to FAT32, it was found by my host and received a static ip address. I installed the software, I need (LabView RT 9.0) using MAX. Now, when I try to boot with the option 'start using software installed on your hard drive', all I get is the message

  "Cannot find a device suitable for C drive.

  I have reset the BIOS, tried to format the drive hard in the other format, uninstalled and reinstalled the software, tried to start the pc target without the USB, but nothing seems to work.

  You have ideas on what goes wrong?

  Thank you

  Samuel

  Have you tried changing the settings of the BIOS for the hard disk controller?

  There could be different modes available.

  Refer to the hard drive of this document: http://zone.ni.com/devzone/cda/tut/p/id/8239?OpenDocument

• drive not ready message "the drive is not ready for use check the a drive, etc.".

  as soon as I connect my camera to transfer the photo I get following message

  The drive is not ready for use: the door can be opened. Please check the a drive; and make sure that a disk is inserted and that the door is closed.

  I can't get rid of this meaasge if I have to cancel it reappears 10 seconds later it just won't close very boring

  Hello

  What is the number and the model of the computer?

  You have the computer floppy drive?

  Were there any changes made on the computer before the show?

  Follow the steps:

  Method 1:

  Remove all external devices connected to the computer such as printers, scanners and external USB hard drive and check if the problem persists.

  Method 2:

  Check the BIOS setting and also, I suggest you to update the BIOS. To update the BIOS, contact the manufacturer or the manufacturer of the access Web site.

  Note: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

• Firefox beta 35. not ready for prime time.

  I spent all weekend trying to get the beta version of Firefox 35 to work. What I found is that * extensions of all it does not work with the exception of the maintenance of the premises. I can't download any extension that Firefox is so famous. The error is something like "unable to install"plugin-name"in its current state." Activation of any extension requires a FF reboot, same places maintenance. Try to remove an extension fails and must be done manually.

  I'm on Windows 7 Premium desktop Firefox 32 bits. I've 'committed' myself to 35 FF last night (which means history and cache out of settling because did not work it extension "expire history by days'), when I found out that 35 played well with some sites using Flash. It was a capricious thing. Many sites worked as usual, but some would not. Examples:
  http://www.Wunderground.com/us/Wi/La_Crosse.html

  http://www.weather.com/weather/5day/l/Hustler+Wi+54637:4:us

  First time I have had a problem with a version beta of Firefox, but it's definitely not ready for prime time. I realize FF tries to get away from what we call 'Exclusive Modules' but 35 FF in its current state just fill in Support of Moz forums with millions of complaints (guess I'm one of the first). I now have 1 extension (the only one that works on 35), the above mentioned "Site Maintenance".

  I thought you might like this report as 'user input '. God knows I've tried... I have downloaded 35 at least a dozen times and then was forced to 34.0.5. So I'm back on 34.0.5

  I presented a report bug here:
  https://Bugzilla.Mozilla.org/show_bug.cgi?id=1108196

  I would like to know if anyone else is having these problems or anyone needs more information. I'd love to help solve this problem. I know that some of you good support people have probably tried to 35. You experience the same difficulties?

  Here is my (34.0.5 but it's the same as I had about 35 last night, with the exception of 'Version') troubleshooting information less 1 million admissions for my printer:

  The application databases

  Name: Firefox
  Version: 34.0.5
  User Agent: Mozilla/5.0 (Windows NT 6.1; rv:34.0) Gecko/20100101 Firefox/34.0
  Windows multiprocessing: 0/1

  Reports of incidents for the last 3 days

  All Crash reports

  Extensions

  Name: Housekeeping
  Version: 1.3
  Enabled: false
  ID: [email protected]

  Graphics

  Description of the adapter: NVIDIA GeForce 9400 GT
  Drivers: nvd3dum nvwgf2um, nvwgf2um
  RAM card: 1024
  ClearType settings: Gamma: Structure of 2200 pixels: ClearType B level: 50 improved contrast: 300
  Device ID: 0 x 0641
  Direct2D Enabled: true
  DirectWrite Enabled: true (6.2.9200.16571)
  Driver date: 19/12/2013
  Driver version: 9.18.13.3221
  GPU #2 Active: false
  GPU accelerated Windows: 1/1 Direct3D 11 (OMTC)
  SubSys ID: 304619da
  Vendor ID: 0x10de
  WebGL Renderer: Google Inc. - ANGLE (NVIDIA GeForce 9400 GT Direct3D9Ex vs_3_0 ps_3_0)
  windowLayerManagerRemote: true
  AzureCanvasBackend: direct2d
  AzureContentBackend: direct2d
  AzureFallbackCanvasBackend: Cairo
  AzureSkiaAccelerated: 0

  Important change preferences

  accessibility.typeaheadfind.flashBar: 0
  Browser.cache.Disk.Capacity: 358400
  Browser.cache.Disk.smart_size_cached_value: 358400
  Browser.cache.Disk.smart_size.first_run: false
  Browser.cache.Disk.smart_size.use_old_max: false
  Browser.cache.frecency_experiment: 3
  browser.places.smartBookmarksVersion: 7
  Browser.Search.Suggest.Enabled: false
  browser.search.useDBForOrder: true
  Browser.sessionstore.Enabled: false
  Browser.sessionstore.max_tabs_undo: 0
  browser.sessionstore.upgradeBackup.latestBuildID: 20141126041045
  Browser.Startup.homepage: http://www.wcwcw.com/
  Browser.Startup.homepage_override.buildid: 20141126041045
  Browser.Startup.homepage_override.mstone: 34.0.5
  browser.tabs.loadInBackground: false
  Browser.urlbar.AutoComplete.Enabled: false
  dom.indexedDB.enabled: false
  dom.mozApps.used: true
  DOM.w3c_touch_events.expose: false
  extensions.lastAppVersion: 34.0.5
  font.internaluseonly.Changed: false
  general.autoScroll: false
  GFX. Direct3D.last_used_feature_level_idx: 1
  keyword. URL: https://www.google.com/search?q=
  Media.GMP - gmpopenh264.lastUpdate: 1413301734
  Media.GMP - gmpopenh264.version: 1.1
  Media.GMP - manager .lastCheck: 1417991594
  network.cookie.cookieBehavior: 2
  network.cookie.prefsMigrated: true
  places.database.lastMaintenance: 1418059778
  places. History.expiration.transient_current_max_pages: 80511
  plugin.disable_full_page_plugin_for_types: application/vnd.fdf,application/vnd.adobe.xdp+xml,application/vnd.adobe.xfdf,application/pdf
  plugin.importedState: true
  plugin. State.np32dsw: 1
  plugin. State.npdeployjava: 0
  plugin. State.npgoogleupdate: 0
  plugin. State.nppdf: 2
  plugin. State.npwatweb: 2
  privacy.clearOnShutdown.cookies: false
  privacy.clearOnShutdown.formdata: false
  privacy.clearOnShutdown.offlineApps: true
  privacy.clearOnShutdown.sessions: false
  Privacy.CPD.cache: false
  Privacy.CPD.Cookies: false
  privacy.cpd.offlineApps: true
  Privacy.CPD.sessions: false
  privacy.popups.showBrowserMessage: false
  privacy.sanitize.migrateFx3Prefs: true
  privacy.sanitize.sanitizeOnShutdown: true
  privacy.sanitize.timeSpan: 0
  Security.disable_button.openCertManager: false
  Security.disable_button.openDeviceManager: false
  Security.warn_viewing_mixed: false
  Storage.vacuum.Last.index: 1
  Storage.vacuum.Last.places.sqlite: 1415513129

  Important preferences locked

  JavaScript

  Incremental GC: true

  Accessibility

  Enabled: false
  Prevent accessibility: 0

  Versions of the library

  NSPR
  The expected minimum version: 4.10.7
  Version: 4.10.7

  NSS
  The expected minimum version: 3.17.2 based ECC
  Version: 3.17.2 based ECC

  NSSSMIME
  The expected minimum version: 3.17.2 based ECC
  Version: 3.17.2 based ECC

  NSSSSL
  The expected minimum version: 3.17.2 based ECC
  Version: 3.17.2 based ECC

  NSSUTIL
  The expected minimum version: 3.17.2
  Version: 3.17.2

  Experimental features

  Good news, friends... and thanks for holding my hand during all this time. I mainly need to know if my problems were me. global or all just... and perhaps others with some configurations.

  I am now on 35.0b2 (not sure how that happened). Anyway, I downloaded beta, that is, reset Firefox, added my cookies.sqlite and permissions.sqlite, has spent half an hour in the 'options', and then checked things and seems to be back in the game!

  Thank you and best regards,
  Axis

• Device could not start - Code 10 - Intel Wireless Card on NB550D

  Hello world

  It's just a normal Toshiba NB550D netbook

  The only thing I change is the card inside Wireless: the original is an Atheros common half mini card. Recently, I have the urge to use internet in 5 ghz (frequency).

  So, I decided to replace the old with the * half mini card Intel Wifi Link 5100 AGN *.
  It turns so well. The pilot is not recognized or specifically the windows tries to install the driver but FAIL is reported. Device manager tool shows a "!" next to the network adapter and when I go the properties on the general tab: "* the device could not start - Code 10."

  I tried many ways to uninstall the driver and reinstall it again; also tried to download the drivers from the website of toshiba for the network card intel.

  Nothing works so far and yes I don't know what to do now.

  The possibility that the card intel is broken or defective is eliminated because I checked with another laptop already and just, it worked like a charm.

  Please help me solve this problem. I really need to use two strips (2.4 and 5 ghz) internet.
  Appreciate any help!

  > The possibility that the card intel is broken or defective is eliminated because I checked with another laptop already and just, it worked like a charm

  Regarding the error code 10:
  http://support.Microsoft.com/kb/943104/en-us

  + The Code 10 error applies mainly to the problems of hardware driver and devices or compatibility problems between the drivers of equipment and additional software that is installed in Windows. +

  I put t think deliver its wireless network card might be a compatibility problem between the BIOS and the wireless network adapter.
  All devices are supported by the BIOS.

  But the WLan card already appears in Device Manager and so I think that there should not be a BIOS compatibility issue.

  Have you checked if the chipset would properly address the Wlan card?

• no boot device during the start of mini mac and bootcamp after adding the partition

  My mac mini is running el capitan and after I added a partition I don't got no boot device but can start at el capitan after pressing option. However, I can't start boot camp. Thank you!

  Last login: kills Mar 31 17:33:01 on ttys000

  independenceadec1s-Mac-mini: ~ the independenceadec1 list $ diskutil

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 256.1 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Untitled Apple_HFS 1 GB 172.5 disk0s2

  3: disk0s3 Apple_Boot Recovery 650.0 MB HD

  4: Microsoft database BOOTCAMP 82.7 GB disk0s4

  / dev/disk1 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: FDisk_partition_scheme * GB 31.9 disk1

  1: disk1s1 Windows_FAT_32 NO NAME 31.9 GB

  independenceadec1s-Mac-mini: ~ independenceadec1$

  By adding a third partition you have damaged the boot loader. If you use Boot Camp to run Windows, so you cannot add a third partition. To set things straight, you will need to repartition the disk to a single partition and try again. A $20 alternative that might work for troubleshoot you is Paragon CampTune X.

• Satellite Pro A10 miniPCI ready for 802.11 g?

  Hello
  I would like to insert a WLAN miniPCI card in a Satellite Pro A 10. Product specifications that it is ready for use with 802. 11 b, but will work an adapter WLAN 802.11 g? And is it possible to use the full 802.11 g or just 802. 11 b, even when the card is compatible 802.11 g?
  Thank you!
  Jens

  Hello

  I checked some information about this device and it seems that you can only use standard Wi - Fi: 802. 11B.
  In this case, you can use 802.11 b standard WLan cards. But perhaps a WLan 2200 b/g card will also work.

  PS: Wireless cards are compatible rewards. the card 802.11 g is compatible with 802.11 b but not 802.11 b-> 802.11 g

• Satellite 4090 BIOS number - message "ready for the update BIOS... ' appears

  Hi all! Excuse my poor English because I'm french.

  A friend gives me his cell phone (a Satellite exactly 4090CDS) because he had a problem.
  In fact, the problem is that when I turn on the computer, I have a single message (not even the toshiba red logo) that is "ready for the update of the BIOS. Place the BIOS update floppy in the drive and press any key when you are ready to move forward."

  So I go to the french site of toshiba, in the BIOS download, I find that I must download this update: http://support.toshiba-tro.de/tools/bios/satellite/4030-4060-100/bios_820.zip

  OK, I download and unpack it on a floppy disk and I start the laptop with the disjette, he said that the update has been successful and it restarts automatically.
  This time, the Red toshiba logo appears, but then I have a black screen with a message:

  Bad checksum (CMOS) *.
  Check the system. Then press the [F1] key.

  And after that, I can't do anything, not even, press F1. If I restart the laptop, I myself meet once more with the first message «Ready for the update of the BIOS...» "and it's still the same.

  If someone could help me understand what the problem is, that would be fine.
  Thank you.

  Bastien.

  It sounds as if your CMOS chip has a problem. It is possible to s that the CMOS battery has failed and the BIOS settings are lost.
  Maybe the RTC battery is empty. In this case, you should connect the AC adapter to charge the battery of the CCF.
  Please note that the RTC battery (CMOS battery) can be fluffed once the main laptop battery has been recharged. In this case, the charge process may take several hours.

  But if after this long process of load this message appears again then I guess the battery is dead.
  I suggest that you only contact your ASP closest to get your phone checked.

• Lab view fpga: device driver for virtex 5

  Hello

  in 2010 I worked on labview fpga and spartan 3

  now, I want to buy a virtex5 xilinix company but I need to know is their a device driver for this kit in labview 2011 or 2012!

  Best regards

  m, s

  Hello mangood,.

  Currently, the only target FPGA that is supported by LabVIEW FPGA, other than our FPGA cards in our product page, is the Xilinx SPARTAN-3E XUP Starter Kit.

• How to fix a sound problem - reading devices no. for the Device Manager on WinXP SP3?

  (1) I can't to Device Manager by following the guide for help on my system.  The steps do not match what is actually showing me my Windows and I can not here the only way I can get to it is to use a link on the help page directly.  Even when I do that, the steps in the help guide still do not match what I see on MY screen.  Is this perhaps an update of this Guide to match my system?

  (2) I need Device Manager to find out what happened on my Audio device.  I have no sound from my speakers.  It happened all of a sudden when my wife was using the computer.  I don't know what she can do both.

  Start/Settings/Control Panel / sounds and Audio Devices Properties shows "No. Audio Device", hence "Volume of the device" is gray.  Audio tab displays 'No peripheral to read '.

  The fastest way to bring up the Device Manager is:
  Start-> Run-> "devmgmt.msc".
  If it detects the sound equipment, but there is a problem with a driver, you will probably see a yellow "!" appears by your audio device.

  If he was working and stopped, you can try to perform a "System Restore" to a point where it worked:

  "How to restore Windows XP to a previous state"
    <>http://support.Microsoft.com/kb/306084 >

  HTH,
  JW

• Error installation software device driver for removable devices in Windows Vista x 64

  I have Windows Vista x 64 installed on my PC and nVidia Forceware motherboard and graphic cards.

  When I plug in any removable drive into my USB 2.0 port, Windows starts the installation of the device driver software and then sees it as an unknown device. The dialog where he asks me if I want to 'locate and install driver software', 'Ask Me later' or 'don't show this message for this device.

  I select the recommended option: "locate and install driver software.

  I click 'Continue' when Windows asks me permission to continue.

  Then, when the execution of the installer of the software in the bottom right of my screen, the installation of driver software for device, it shows "unidentified device failed.

  Then another window pops up saying this:

  "Found New Hardware - device unknown".

  Windows encountered a problem installing the software driver for your device

  Windows found driver software for your device but encountered an error trying to install it.

  Kodak

  An error occurred during the installation of the device:

  The driver for this device is missing a necessary entry. Maybe it's because the file INF was written for Windows 95 or later. Contact your hardware vendor.

  If you know the manufacturer of your device, you can visit their website and check the support section for driver software. »

  That's what he does when I'm trying to connect my Kodak Easyshare M550 digital camera. I would go ahead and contact Kodak, but the problem seems to extend to ANY removable device on my computer.

  For example, I have a Lexar Flashdrive. When I plug it into my USB 2.0 port, it Windows says the following:

  "Windows needs to install driver software for your USB Flash Drive", etc...

  'Install the device driver software', 'USB Flash Drive search Windows Update'...

  Then a window opens asking me to "insert the disk that came with your USB key. Problem is that no driver disk not supplied with the hardware that Windows Vista is supposed to come with the drivers. I know this because the camera and usb flash drive worked very well until I reinstalled Windows Vista on my new hard drive (new installation, because my old hard drive crashed) and I've NEVER had to install device drivers for Windows to recognize it as a removable drive and operate automatically.

  Also, I installed Daemon Tools Lite and I had to manually "Update" the device driver to point to the "Windows\INF" folder in my hard drive, after copying the cdrom files needed for the specific subfolders for windows to let the program assign a drive letter for the drive virtual it creates.

  I think that perhaps not all device drivers have been installed when I installed Windows Vista, this time. If that's the problem, I don't know how that could happen, nor how to fix it, but I really prefer to find a way to solve this problem without reinstalling Windows Vista again. I don't mind not manually install the drivers as long as someone can show me what files to copy and where to find them on the Windows Vista disk that I bought at Microsoft. I KNOW that Windows HAS come with these drivers.

  If anyone knows how I can fix this, please tell me, because it's ridiculous to not be able to use any removable device readers (except for the use of all Flash drives). Thanks in advance.

  I know it can be frustrating to solve problems.

  (A) was this post or hibernation sleep?

  Microsofts troubleshooting KB

  http://support.Microsoft.com/kb/928631

  (B) the bios settings

  First of all you do not state if you tried to see if there was a setting in bios disabled USB ports during the startup. Or how the bios was set to install devices automatically. If you check your manual site or the motherboard manufacturer

  It will tell you which key to press. And where your USB ports are on or off. Some systems do not have to turn on or off.

  Plug n play OS on conscious

  could help Vista automatically recognize your USB

  (C) what version where do you use? SP1? or gold?

  (D) USB hubs may cause problems just be hubs. Power connected?

  (E) and of course if it is a case check connection in the right port. Return panel slide? plugged into port back?

  Hope something here helps

  Keith