Application of VPN S2S packet capture

Similar Questions

• Application of VPN S2S (with NAT)

  Hello experts,

  ASA (8.2) and standard Site 2 Site Internet access related configs.

  Outside: 1.1.1.1/24-> peer IP VPN S2S.

  Inside: Pvt subnets

  Standard "Nat 0' orders and crypto ACL for our remote offices, local networks with IP whp program.

  Requirement:

  Need to connect the PC to external clients (3.3.3.3 & 4.4.4.4) on tcp/443 via vpn S2S on our LAN. Client only accepts only the host with public IPs.

  I need NAT to my internal IP to the public IP say 1.1.1.2 and establish the VPN tunnel between 1.1.1.1-> PRi Client-side & secondary IPs (Cisco router).

  (without losing connectivity to remote offices). No policy NAT work here?

  ex:

  My Intern: 10.0.0.0/8 and 192.168.0.0/16
  Assigned IP available for NAT (some time to connect to the client only): 1.1.1.5

  External client LAN IPs: 3.3.3.3 & 4.4.4.4

  PAT: permit TOCLIENT object-group MYLAN object-group CUSTOMER LAN ip extended access-list

  NAT (inside) 5-list of access TOCLIENT

  5 1.1.1.5 (outside) global
      
   Crypto: tcp host 1.1.1.5 allowed extended CRYPTO access list object-group CUSTOMER LAN eq 443

  Outsidemap 1 crypto card matches the address CRYPTO
   
  Customer will undertake to peer with IP 1.1.1.1 only.

  Do I need a ' Nat 0' configs here?

  Also, for the specifications of the phase 2, it is not transform-set options gives. Info given was

  Phase2: AH: people with mobility reduced, life: 3 600 s, PFS: disabled, LZS Compression: disabled.
  This works with options of the phase 2?

  Thanks in advance

  MS

  Hello

  «Existing NAT (inside) 1 & global (outside) does not interfere with NAT 5 when users try to reach the ClientLAN.»

  Your inside nat index is '1', while the dynamic policy-nat is index '5 '.

  "" For the phase 2 in general, we define Crypto ipsec transform-set TEST ".

  Sure, the remote tunnel peers even accept transform set, everything you put up with the example below and distant homologous put the same tunnel.

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  "In this scenario, no need to define any what and just add empty transform don't set statement under card crypto?

  No you need a defined transformation.

  "3. If we want to limit the destination port 443, I need to use separate VPN filters?

  That's right, use a vpn-filter.

  "4. we have several phase 1 configs, but wanted to use AES256 & DH5 (new policy)"... for s2s, these options work fine. ""

  Of course, you have set the phase 1, as required.

  Thank you

  Rizwan James

• Packet capture vpn access list filter

  I just install a VPN filter to secure traffic between two of our facilities. As a good security admin, I am only allowing good ports and blocks everything else. Now I see one-way packet loss.

  I wanted to set up a capture of packets to detect which packages were being allowed and which were dropped. However, none of my packet captures are showing all the captured packets. I tried the following shots.

  capture the data interface type DPEP bullies xo [Capturing - 0 bytes]
  match ip 10.1.8.0 255.255.252.0 all

  capture the data type DPEP raw access-list 105 interface xo [Capturing - 0 bytes]

  capture the data interface type DPEP raw asa_dataplane [Capturing - 0 bytes]
  match ip 10.1.8.0 255.255.252.0 all

  It is certainly a problem of formatting on my part that I am does not detect traffic to subnets that the traffic that goes with success.

  Any help would be appreciated. Thank you.

  Hi Michael,

  do not change the VPN filter... you created a dummy access just to capture list and who as a rule and use it to capture.

  Concerning

  Knockaert

• How to pass the traffic of a site VPN S2S by ASA to another S2S VPN site?

  I have a need for hosts on separate VPN networks connected to my ASA corp to communicate among themselves.  Example: Host A site 1 a need to communicate with host B on the site 2.  Both sites 1 & 2 are connected via the VPN S2S.  I would get every site traffic to flow through the ASA at the other site.  Where should I start my configuration?  NAT? ACL?

  I can ping each host in the network Corp. but cannot ping from one site to the other.  I set up same-security-traffic permit intra-interface and addition of NAT and rules the ACL to allow/permit 1 Site to contact Site 2.  When I do a trace of package through Deputy Ministers DEPUTIES, packets are allowed to pass. I read different that tell no NAT y at - it something at the other end of the VPN to do?  should NAT and ACLs rules be mirrored? Just in case, a site is an instance of MS Azure VM and the other is a 3rd party VM instance.

  On the HubASA, can I set up a new card encryption that selects the Site1 Site2 traffic and protect the traffic and value her counterpart Site2 public IP or just add this selection of traffic to the existing encryption card for the existing tunnel between HubASA and Site2?

  Just add this traffic to the existing encryption card.

  Remember that this should be added on three routers (two hubs and there has been talk).

  Site1

  CRYPTO ip access list allow Site2 subnet >

  CRYPTO ip access list allow subnet training3 >

  CRYPTO ip access list allow subnet HUB >

  Site2

  CRYPTO ip access list allow Site1 subnet >

  CRYPTO ip access list allow subnet training3 >

  CRYPTO ip access list allow subnet HUB >

  Training3

  CRYPTO ip access list allow Site1 subnet >

  CRYPTO ip access list allow Site2 subnet >

  CRYPTO ip access list allow subnet HUB >

  HUB

  CRYPTO_1 ip access list allow Site1 subnet >

  CRYPTO_1 ip access list allow Site1 subnet >

  CRYPTO_1 ip access list allow Site1 subnet >

  CRYPTO_2 ip access list allow Site2 subnet >

  CRYPTO_2 ip access list allow Site2 subnet >

  CRYPTO_2 ip access list allow Site2 subnet >

  CRYPTO_3 ip access list allow subnet training3 >

  CRYPTO_3 ip access list allow subnet training3 >

  CRYPTO_3 ip access list allow subnet training3 >

  Each of these ACLs is attributed to their respective crypto cards.  CRYPTO_1 is assigned the site1 crypto map, CRYPTO_2 is assigned to the site2 crypto card... etc.

  I hope that's clear

  In addition to this, you need to configure identity NAT / NAT provides both the HUB and the spokes of sites.

  --

  Please do not forget to select a correct answer and rate useful posts

• Packet Capture on ids

  Hello

  We need the 'packet capture' setting on all the signatures of attacks on a joint-2 V4.1.4 and a sensor 4210 V4.1.4. We use CiscoWorks VMS for the configuration of all sensors, but there seems to be no way to enable this setting for a selection of signatures at a time. This is apparently a different setting than the ip logging (for which we can select a large number of signatures to be configured at the same time). It seems to me that the only way to change this is to go into each separate signature configuration and change the value there. But it is almost not doable. Any other possibility?

  Now that IPS Version 5.0 was officially announced (to be released early next month), I can tell you about some of the new features that can help in this area.

  The new IDM (Intrusion detection device manager) which is that tool for basic configuration for the web of the sensor will allow you to select several signatures (now the control key while you select each signature), do a right click to bring up a window of action event and grant shares of event (such as the Packet Capture, which was renamed ProduceVersboseAlert in 5.0) for all signatures in a few mouse clicks.

  So you will not need to manually edit the XML of the probe to make the same change to a large number of signatures.

  NOTE: I work in the team of sensor and therefore did not expertise on product ID MC (VMS). I don't know if this same functionality offers the IDS MC in virtual machines. But ID MC should, at a minimum, be able to import changes made through IDM.

  Some other new features are what we call risk score and event Action overrides. With the risk rating will now have a level of risk calculated from 1 to 100. The risk rating is calculated according to the severity of the Signature, the loyalty of the Signature (how well it detects that the attack) and the target value (how the target address is important to you).

  Mainly the level of risk is a method to better sort the order of importance of the alarms, but can also be used with the new feature of event Action more than wrinkles.

  Each type of action (such as ProduceVerboseAlert) can be assigned a specific range of risk (for example 80-100) rating. Any alert that has risk rating will have this action also made previously specific action by signature. (If no alert with a risk rating of 80-100 would have ProduceVerboseAlert added to this alert action, if she had not already been configured on the individual signature).

  The filters have also changed a bit.

  You can now name each filter on the sensor itself.

  And even to add a description to a new field of user comments.

  The filters now also filter specific actions (in 4.x all actions has been filtered, but in 5.x, you can filter the actions in the block for example or even allow the alarm to be generated).

• Multiple context mode, how do I download packet capture file

  Hi guys,.

  Is there a way to download the capture of packets from a specific context? I know I used to use https:///Admin/capture/ to download if it's just a context.

  The ASA uses mgmt 0/0 for the management and it is connected to a separate network of OOB. Only this network has TFTP servers to download the capture file. The context in question is in transparent mode. Its IP address doesn't have access to a TFTP server.

  Thank you!

  Difan

  Hello Difan,

  Please see the following document.

  https://supportforums.Cisco.com/document/69281/ASA-using-packet-capture-...

  Also, what version of the ASA code do you use?

  Kind regards

  JAI Ganesh K

• Access to the DMZ to remote sites via VPN S2S

  We have an ASA 5520 and two remote site ASA 5505 that connect to each other through tunnels VPN S2S. They are doing tunneling split, while local traffic passes over the tunnel. We are local LAN (10.0.0.0/16) and our network to the DMZ (10.3.0.0/24) on the main site. The DMZ hosts our external sharepoint, but we access it internally

  The problem is site A (10.1.0.0/24) and B (10.2.0.0/24) have no idea of it, and when you try to go to the site, it fails. You can access it via the external site address, but that's the only way. Normally the external address is blocked when you're an intern.

  That I'm stuck on is even when we had all sent traffic from Site A to our Senior Center, would find it yet. I do a separate vpn purely tunnel that traffic to DMZ?

  Yes. So if you do this in ASDM under Edit Site profile connection Site, it will look like this.

  Local network: 10.0.0/16, 10.3.0.0/24

  Distance: 10.1.0.0/24

• Ontario Regulation distributes dynamic routes via VPN S2S

  Hi halijenn / experts

  (1) please let me know if IPP works on a Site in tunnel

  (2) I have a behind remote ASA 10.10.1.0 and 10.10.2.0 network that must be distributed to another branch ASA with S2S ASA remote via OSPF

  3) there is an L3 Switch behind the ASA of the branch and Switch L3 there is a router that has a default route pointing router WAN

  Router WAN
  |
  |
  Users-> router-> L3 Switch-> ASA-> Internet-> remote ASA branch (10.10.1.0, 2.0)

  Note: 10.10.1.0 2.0 AND are already configured in the ACL Crypto at the ends.

  Users are able to reach the 10.10.2.X network to the remote end.

  Now for the 10.10.2.0 static routes are already there in the router and the switch finally pointing the ASA branch however as the network grows, it is impossible in the router behind the switch to add static whenever routes (such as the default route to router WAN points). This is why in order to learn routes dynamically, I will add an ospf process to the ASA to branch with the following configuration. Please let me know if iam correct when I add IPP and other OSPF commands to the ASA of the branch. (hope I have nothing to do on ASA remote associated with IPP or OSPF?)

  I take just an example of a remote host 1 10.10.1.4. Inside ASA interface leading to users is 172.16.1.0/24

  access-list redistribute allowed standard host 10.10.1.4 255.255.255.255

  router ospf 1
  network 172.16.1.0 255.255.255.0 area 0
  Journal-adj-changes
  redistribute static subnets redistribute route map

  In addition, I will also be allowing the order for IPP in the encryption of the VPN S2S said card.

  Please help me understand if I'm wrong

  Pls set the OSPF firstly on the SAA process before removing the static routes. Once you have confirmed that the OSPF is configured correctly and the roads are in the OSPF database, then you can delete the static routes. Static routes will always take precedence over OSPF because it has higher metric. Please keep the default route configured on the SAA.

  Hope that confirms it.

• Integrated Packet Capture: CEF or process switched?

  I have a question about EPC.

  When I configure it there is an option

  LABRTR #monitor capture point ip?
  CEF IPv4 CEF
  switching to packet switching process

  LABRTR #monitor capture point ip

  When I choose different router cef gives me an option to choose the interface, but when I choose to process switching , it gives me a few options.

  I wonder what is the best choice when you are capturing?

  Thank you!

  Hello

  For normal map data packages, use the path of the CEF. For packets that are destined for the router itself, use the dial-up process.

  HTH.

  Evaluate the useful ticket.

  Kind regards

  Steve

• How to enable / on ASA5520 packet capture uploading

  I need to install the packet sniffing inside and monitoring of the interfaces of the external interfaces of the SAA for indoors and outdoors. What is the syntax for surveillance, and how save/copy the .pcap off the coast of the asa? Also, how do you specify the random source (gt1023) port?

  Here is my shot of dagger inside example:

  entry Packet-trace within the udp 10.1.0.1 xxx 207.1.1.1 detailed sip

  In addition, can I run an inside and an outside track at the same time?

  Thank you

  -Scott

  Scott,

  After setting the capture

  Go to the

  http://ipadd of pix/capture/OCAP/sip-trace

  Make sure you have http enabled on this interface, you are trying to access.

  Write it down, if this can help!

  Gilbert

• ASA in ASA VPN-encrypted packets "get lost" in the tunnel

  Hello

  We have a VPN site-to site between ASAs. Both on the v9.1.6 code. On distance ASA, it also has to do NAT source and destination. We see the traffic 'interesting' made from the results of the remote side in ipsec SA. Late has ITS correspondent. Corresponding spinnakers. However, the remote end HIS watch packets encrypted, decrypted none. Late ASA shows no packets encrypted/decrypted. So, how can I "lose" packages in my VPN tunnel if both ends have matching SAs/SPIs?

  Best regards

  Richard

  Hello

  Could be incorrect rules NAT or an access list refusing ESP packets somewhere in the path between the two ASAs.

• fall of site to site vpn icmp packets

  Hello

  I test site to site vpn between ASA and cisco router with GNS3, topology is base the tunnel is up but the question when the remote host ping from both sides it is drops icmp, see router command and ASA do not include droppings. Here is a sample output from ping when I try to remote client ping. any help is appreciated :)

  Instant topology is attached, also configs

  Thank you

  84 bytes from 10.20.20.5 icmp_seq = 59 ttl = 63 times = 79,004 ms
  10.20.20.5 icmp_seq = timeout 60
  84 bytes from 10.20.20.5 icmp_seq = 61 = ttl 63 times = 70,004 ms
  10.20.20.5 icmp_seq = timeout 62
  84 bytes from 10.20.20.5 icmp_seq = ttl 63 time = 63 = 59,004 ms
  10.20.20.5 icmp_seq = 64 timeout
  84 bytes from 10.20.20.5 icmp_seq = 65 = ttl 63 times = 50,003 ms
  10.20.20.5 icmp_seq = timeout 66
  84 bytes from 10.20.20.5 icmp_seq = 67 ttl = 63 times = 59,003 ms
  10.20.20.5 icmp_seq = timeout 68
  84 bytes from 10.20.20.5 icmp_seq = 69 = ttl 63 times = 50,003 ms
  10.20.20.5 icmp_seq = timeout 70
  84 bytes from 10.20.20.5 icmp_seq = 71 ttl = 63 times = 58,003 ms
  10.20.20.5 icmp_seq = timeout 72
  84 bytes from 10.20.20.5 icmp_seq = 73 = ttl 63 times = 50,003 ms
  10.20.20.5 icmp_seq = timeout 74
  84 bytes from 10.20.20.5 icmp_seq = 75 ttl = 63 times = 69,004 ms
  10.20.20.5 icmp_seq = timeout 76
  84 bytes from 10.20.20.5 icmp_seq = 77 ttl = 63 times = 237,013 ms
  10.20.20.5 icmp_seq = timeout 78

  R1 ipsec crypto #sh her

  Interface: FastEthernet0/0
  Tag crypto map: map, local addr 100.100.100.2

  protégé of the vrf: (none)
  local ident (addr, mask, prot, port): (10.20.20.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (10.20.10.0/255.255.255.0/0/0)
  current_peer 100.100.100.1 port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: 14, #pkts encrypt: 14, #pkts digest: 14
  decaps #pkts: 28, #pkts decrypt: 28, #pkts check: 28
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  Errors #send 0, #recv 0 errors

  ciscoasa # sh crypto isakmp stats

  Global statistics IKEv1
  The active Tunnels: 1
  Previous Tunnels: 1
  In bytes: 1384
  In the packages: 12
  In packs of fall: 0
  In Notifys: 8
  In the constituencies of P2: 0
  In P2 invalid Exchange: 0
  In P2 Exchange rejects: 0
  Requests for removal in his P2: 0
  Bytes: 1576
  Packet: 13
  Fall packages: 0
  NOTIFYs out: 16
  Exchanges of P2: 1
  The Invalides Exchange P2: 0
  Exchange of P2 rejects: 0
  Requests to remove on P2 Sa: 0
  Tunnels of the initiator: 1
  Initiator fails: 0
  Answering machine fails: 0
  Ability system breaks down: 0
  AUTH failed: 0
  Decrypt failed: 0
  Valid hash fails: 0
  No failure his: 0

  Hello

  On router R1, you gave the default route as output interface. Instead of using the output interface replace the IP address of the next hop. It will solve the issue of the reduction of ping.

  IP route 0.0.0.0 0.0.0.0 FastEthernet0/0

  IP route 0.0.0.0 0.0.0.0 100.100.100.1

  HTH

  "Please note the useful messages and mark the correct answer if it solves the problem."

• My application forms is not having captured

  Hello

  I came to know OATS recently. I want to try this if I can use for the application that I have tested. This application is built using Oracle Forms and using weblogic and I access it by providing the url on IE that starts then application form. I can record the launch browser and can navigate to correct the url but after that when forms get launched is not on the same window, I am not able to capture anything on it. From now on, it is purely on my personal learning and personal initiative. can someone give some suggestions?

  Hello

  EBS/forms--> automation tools manage, activate jre. If you can not find jre is here, then install jre appropriate to the version of OATS (you can find support jre version in the accompanying note) and activate the same. Check also addons are enabled in the browser.

  Try this and let me know if you face any problem

  Kind regards

  Dembélé M

• The vMA traffic packet capture

  I'm deploying a new VM vMA. I have the virtual machine on a different subnet than my regular production network. Everything is good so far except when I try to run the command 'vma-update' When I do that, I get a message "no route to host". I followed it down to the access list that I have on my switch. Do I have to do now is execute a capture of packets to see what IPS the vMA is in talks with so I can enable them through on my access list.

  What is the best way to run a capture of the vMA packages?

  Thank you.

  Well the URL can be solved in several addresses/etc, but I guess already know you that.

  Eaiest is to perform a tcpdump, it is not installed by default on the vMA, so you can get a YUM repo and configure another session in which you make a tcpdump while you're trying to run vma-update

• iOS Application Loader: "a request packet not valid."

  Hello

  I often download of AIR apps to iTunes Connect via the Application Loader, but for the last 24 hours he has been complaining that "the file is not a valid request packet.

  I use AIR 4.0 at the command line with all certificates of right and app IDs, and I decompress and recompress the payload on a Mac I've done hundreds of times before. And it comes up with 3 all the apps that I'm trying to update is not an isolated incident.

  Nothing has changed since 4.0 AIR which would explain it? Anyone who knows the same thing this week?

  HI ~ I have the same problem in Mac OS 10.6 and application Loader v2.5.1, but I use Mac OS 10.7 & v2.9.1 application Loader is ok.

  You can try it.