Arduino uno error 5002

Similar Questions

• Arduino Uno + Labview 8.5

  Hello

  I am trying to send commands to the Arduino Uno using Labview 8.5. Tried setting basic series writing and Read.vi the baud rate 9600 and rest of the default parameter, selected the correct COM port and wrote the command

  i5000\r\n

  This command is to rotate a plate of rotation using a motor, 5 degrees. There is no response.

  I can run this command by using NOR-MAX and the Arduino terminal and the motor move.

  Could someone please tell me what am I doing wrong? I had done my own vi using VISA initially, but it didn't work so I tried the example of OR. Is the example for a reason any not applicable to my case?

  There is no error but the motor does not move.

  Thank you very much..

  
  

• LabVIEW arduino uno bad data transfer

  Hello

  I have some problems with the transfer of data from the arduino uno to labview.

  I did a VI where I can control the power of a heater with measurements of temperature with arduino uno.

  The problem is that from time to time the incorrect temperature is captured in labview by missing the number or a number, for example. LabVIEW gets 1.25 ° C instead of 15.25 ° C or 2000 ° C instead of 20.00.

  When I look at the program arduino tracer series these errors do not occur. So I guess it will be a problem with the settings of labview or my VI.

  Parts joined a set of data extracted from the VI and VI himself and the arduino script

  Yes.  The Subvi has 2 major problems.

  The first is as I said.  You set up and close the serial port each iteration.  There is a risk that the device could be send data that you won't miss the moment, that the port is closed.  (Even if she doesn't really explain why you miss the decimal point in the middle of the data bytes.  Serial ports must be configured and opened when the program starts.  Writing and reading within the loop.  And not closed when the program ends.

  The second major problem.  Why you have the property Bits of data cable up to the number of bytes to read.  Bytes and pieces is two different entities.  And in this case, the data bits is the number of bits of data defined by the configuration of the serial port.  Probably 8 and would still be 8 and has nothing to do with the number of bytes actually in the serial port.  Number of bytes to read is how many bytes you want to actually read the serial port, could be 1, 50, 1000,...

  Is your device send data continuously without asking?  Should I use a stop character?  If this isn't, by using a stop as a return character, carriage or line break, then it should.  It will help you to break the ASCII data that crosses into packets.  Configure your serial port is set up to search for characters of endpoint and it would be a line break character. Use the termination character, and tells your VISA read an arbitrarily large number.  A number that is larger than the longest message that you expect to receive.  The VISA read will return as soon as she sees the character of judgment and you give a full data package.

  It is often a good idea to have a communication protocol of request/response with your device.  You write a command that says 'give me the value.  It reads and responds to the back and gives value.  Otherwise if he sends just data continuously without asking confirmation and that you do not read fast enough, you could extend your serial port (which would give an error and you could lose data), and even before that, you could read old data which is at the front of your stamp series while your device has already sent hundreds of data points more after that.

• Pilot NI VISAS for Arduino Uno R3 configuration problem

  Hello, my name is Leong. Currently, I have the problem with the configuration of the Driver NI-VISA for Arduino. Once I have downloaded the driver NI-VISA on the Web site of NOR, I NI-VISA drivers for operation and select the hardware bus type should I choose. After I selected the hardware bus type, the inviting of NI-VISA me to select the device ID I was installed, my device for Arduino UNO of R3 ID is USB\VID_2341 & PID_0043. I select my device ID and click the next button. I have the following button click, the screen is displayed as the following:

  

  I chose to install the files generated on this computer and click Finish. When I click on finish, the error screen appears as below:

  

  May I know what is the problem, so I know how to solve the problem? Thank you very much for your kind help.

  Kind regards

  Berre

  do not use the device driver Wizard, simply select the serial port you need VISA

• VPP error 5002

  Hello

  I just signed up for the VPP Business and can't seem to get my install ID correctly to make a purchase.

  After signing in, I get the message, "this identifier Apple has not yet been used with the purchase Volume for business program.»  Please click on continue to set up this account for use on the company store. »

  I click on continue and then get error 5002, "an unknown error has occurred."

  I tried at least half a dozen times and get the same error.

  Help!

  Thank you.

  We have the same problem, except that it is for the purchase of Volume for the education program. Also, took place on February 12, 2016. I hope someone knows how to solve this problem.

• Timed signal generation TTL with the NI USB-6501 to be read by Arduino Uno

  First of all, I want to apologize - I am very, very new to LabVIEW and brand new to the development of the software of control equipment in general. I tried to find an answer to this question already, but I'm not entirely sure what I'm looking for.

  I have currently a work program LabVIEW which operates a gun card NI USB-6501. Due to the nature of having a machine that springs from a powerful beam of electrons, we want to assure you that if the computer controlling stalls or fails for any reason, we have built-in security that can stop the gun. Our current idea is to connect an Arduino Uno on a PIN on the USB-6501 and LabVIEW to generate a timed signal, which may read the Arduino. If the signal fails (indicating that the control computer has queued or off), the Arduino triggers a power relay that is independent of the control computer and turns off the gun.

  I understand that the USB-6501 operates on TTL signals, so the signal that I should be something in the sense of "output TTL high, wait 1 second, output low expectations, a second, repeat TTL ', but I have no idea how to go about programming in LabVIEW. My first thought was that it is a square wave by using the function "simulate the signal" output, or to have trigger an iterative Boolean signal, by using the function 'DAQmx write', but I don't really understand how do to implement or another idea, or if an idea would even work.

  Any advice would be greatly appreciated.

  Hi Elizabeth,.

  THINK THE STREAM!

  When do you DATAFLOW think everything falls in places!

  Several problems:

  -You have to put that MAKE impulse VI in his own loop parallel to your main VI!

  -When you place this generation of impulses in the effects loop ("TTL arduino low-high") you should put the CreateTask and StopTask outside the loop: no need to create/stop the task in each iteration.

  -Why are there points of constraint to waiting functions?

  -Why is there bent wires? You know Ctrl-U?

  -LabVIEW comes with an extensive library of example screws: you looked at all these examples DAQmx?

  -Suggestion: Learn more about the "structures of producer-consumer"!

• Problem with Labview communication with Arduino Uno

  Hello

  I tried to run a simple program in labview through my Arduino Uno R3 all morning and keep running into the same problem: no response from my Board of Directors. I'll catch you up on what I've done so far:

  -flashed LIFA Base to my Arduino
  -Downloaded the driver update of VISA

  written-a the block diagram (I hope) for a led on off function

  When I run the program in labview, the RX flashing intermittent, continue for 30 seconds before stopping. The led on pin 13 is not turned off as it should, and I have no control over the power function light. I also tried a program of control of servo with no response and the same flash of RX. Never the TX flashes.

  I am quite stuck, so any help is greatly appreciated. Also I'm not a comp sci guy, I'm just an engineer in mechanics with a half of C++ so keep pg when it comes to the language of the computer.

  I've attached a picture of my diagram of LED, see if you can spot a problem.

  Thanks in advance!

  SOLVED: Reset the Arduino card after that labview had sent his orders (while the RX light was still flashing). Works like a charm.

• "Launch4j" error message when you try to download the Arduino Uno start-up program

  I successfully downloaded and used this program in the recent past, using Windows 8, but even if I can download it now, when I try to open it on the desktop, I get the message: error "Launch4j. I'm not a computer specialist and have not been able to get much help from the local computer providers, but I have a feeling that there must be a simple solution.

  Any ideas would be very useful.

  Colin.

  Hi Colin,

  Right-click on the application and select run as administrator, and then check if it works. If this does not help, reinstall the application in compatibility mode.

  Refer to this link: make the programs more compatible with this version of Windows

  http://Windows.Microsoft.com/en-in/Windows-8/older-programs-compatible-version-Windows

  Also check out this link:

  http://Forum.Arduino.cc/index.php?topic=210854.0

  Contact the Arduino support and see if they can help you.

• ERROR 5002

  I'm having a problem when I try to load music on my mac in decline during the use of apple's music. "Results of genius cannot be updated now. An unknown error occurred (5002). »

  Tried:

  Leave music on all apple devices and only opening music apple on mac.

  disconnection and sing again.

  Still no luck. any suggestions?

  Hello

  Maby, as this can help

  Find an iTunes, error code - Apple Support

  Get your number and follow the instructions

• analog multiple read arduino serial communication

  Hello

  I'm working on a project and I'm new to Labview,

  Can someone tell me how to read the multiple analog playback on Labview in communication series with Arduino UNO?

  I tried, but data are somehow in error.

  I have also attached my current code of vi and arduino.

  Please help me.

  Hello

  You then send a value of more than your Arduino project. But in you VI you do not analyze the data entering split of voltage and current.

  I suggest that you send a fixed string with voltgae and data current so that you know in your VI you will receive the number of bytes and how to divide the data.

  Kees

• Error-20020 when you use Express "Filter" VI?

  Help for error-20020 indicates the cut-off frequency Fc must answer 0<= fc=""><=>

  Implement

  Using LIFA read an Arduino Uno's analog input signal to about 125 samples per second.

  Using Express 'Filter' VI to filter the data. The filter is set to low-pass, Fc = 10 Hz, Type Buterworrh and IIR.

  The Express filter works when CF is set to 0.5 Hz.

  Why the CF must be st to a lower value to! / 100 of the sampling frequency?

  What does do to get a low pass frequency of 10 Hz wien cut-off sampling rate is 125 samples per second?

  Howard

  If you right-click on the express VI and select open front panel, you can transform into a Subvi regular and forest down into it and see how it works.  You will see in his heart basic filter functions, you can find in the range of Signal Processing.  There are also "Point by Point" filters in this palette that allow you to work a stitch at a time.  They also have an entry that allows you to tell him what really is the sampling frequency.

• Arduino MyRIO via UART communication

  Hello

  I am trying to achieve the data between MyRIO1900 and Arduino via UART communication.

  Interface UART on Arduino Uno is minus 16 MHz clock.

  The UART to myRIO can set baud rate. However if the frequency is different from the Arduino, the connection will not be built.

  How to set the frequency of MyRIO UART? What is the default frequency of MyRIO UART? Where can I find this setting?

  I don't understand. If the transfer speeds are the same, you should be fine. The clock frequency is used to calculate the bit rate and is the rate that data is transmitted/received.

• LabVIEW Interface for installation of the Arduino

  I want to install the LabVIEW Interface for Arduino Toolkit, so I can control an Arduino Uno R3.  Say the instructions to download and install the VIPM and then you can download and install the Toolkit through the VIPM.  The only problem is that workplace of our company doesn't have access to the internet for security reasons, so the VIPM will not be able to download the Toolkit.  How can I download manually the Toolbox for a laptop without LabVIEW, save it on a usb key, then install manually on the workstation with LabVIEW?  Any help would be greatly appreciated.

  I asked the very question sometime back and here is the answer I received. I decided to use another computer on the network for the work of the Arduino, so I never tried what was suggested.

  Let us know how it turns out.

• Arduino and LabVIEW makerHub

  Guys I use Arduino UNO and wind sensor. I need to see the wind speed and temperature. I did that with LINX and its proper functioning, my problem now is, quite slow results, can someone help me I need to change my program to work well and produce quick results on the graph of thermometer and waveform. I'm download my block diagram.

  Thank you.

  dony_92 wrote:

  I think that these numeric operators makes things slowly, so is it possible to calculate faster and then I think that the results will be showing much more quickly on the front panel. I need to show every second on the façade on the speed of the wind and temperature. So I hope I explained well what I need.

  Turn OFF, highlight execution (the light bulb in the toolbar).  This is a debugging tool which slows your program to a crawl but you indicates the values that they are run.

• Arduino to control with labview

  Hello
  I want to use my arduino uno with Labview,

  I just need the arduino to send pulses of 5 volts X dry all the seconds
  How can I do through labview?

  Thank you

  And all Group Arduino for Arduino/LabVIEW