ASA 5515 WITH LICENSE OF FIREPOWER

Similar Questions

• CISCO ASA 5515 WITH THE VERSION OF FIREPOWER

  ASA 5515 service with the power of fire. Can be managed with ASDM firepower. ?

  Anyone suggests Versions for firepower, ASDM, ASA?

  Kindly help

  You will find it useful to install the Module of firepower on ASA for the management of the premises:

  http://www.Cisco.com/c/en/us/TD/docs/security/ASA/Quick_Start/SFR/firepo...

  Thank you

  Guillaume

  Rate if this can help!

• ASA 5510 w / license more lost security contexts

  I have an ASA 5510 with license more than security and when I looked the devices a few days ago, I had 2 contexts, however after you have configured the port of Mgm as a regular port contexts show 0, why?  I can't find anywhere on the internet where this problem occurred: this is the result of show worm:

  Cisco Adaptive Security Appliance Software Version 7.0 (8)

  Updated Sunday, 31 May 08 23:48 by manufacturers

  System image file is "disk0: / asa708 - k8.bin.

  The configuration file to the startup was "startup-config '.

  SHIELDASA01 up to 21 hours 16 minutes

  Material: ASA5510, 256 MB of RAM, processor Pentium 4 Celeron 1600 MHz

  Internal ATA Compact Flash, 256 MB

  BIOS Flash M50FW080 @ 0xffe00000, 1024 KB

  Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)

  Start firmware: CNlite-MC-Boot-Cisco - 1.2

  SSL/IKE firmware: CNlite-MC-IPSEC-Admin - 3.03

  Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.05

  0: Ext: Ethernet0/0: the address is 0021.a025.2d3c, irq 9

  1: Ext: Ethernet0/1: the address is 0021.a025.2d3d, irq 9

  2: Ext: Ethernet0/2: the address is 0021.a025.2d3e, irq 9

  3: Ext: Ethernet0/3: the address is 0021.a025.2d3f, irq 9

  4: Ext: Management0/0: the address is 0021.a025.2d3b, irq 11

  5: Int: not used: irq 11

  6: Int: not used: irq 5

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 25

  Internal hosts: unlimited

  Failover: Active / standby

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 0

  GTP/GPRS: disabled

  VPN peers: 150

  This platform includes an ASA 5510 Security Plus license.

  I'm not showing the serial number and keys licese for obivious reasons.  Any help? Thanks in advance.

  You might want to try upgrading your IOS on the SAA, see if it can help, can you check the firewall mode (single or multiple) you're currently on? is your asa transparant or routed?

• Communication between subinterface on ASA 5515 X with version 9.1.

  Hello

  I have an ASA 5515 - X with version 9.1.

  I created 5 secondary interfaces in my 0/1, with different subnets while the firewall is the front door of my user.

  0/0 - outside - WAN

  0/1.1 - inside16 - 172.16.16.1/23

  172.16.30.1/24 - inside30 - 0/1.2

  0/1.3 - inside33 - 172.16.33.1/24

  0/1.4 - inside40 - 172.16.40.1/24

  172.16.128.1/24 - inside128 - 0/1.5

  0/2 - test - 10.10.10.1/24

  10.x/24 network my internet works fine. But, while this does not work for my secondary interfaces. They communicate with themselves.

  When I try to trace a package. I've been out below attached.

  Please suggest.

  Kind regards

  Emilie

  You use the (necessary) command:

  permit same-security-traffic inter-interface

• ASA 5510 Anyconnect licenses with Cisco Anyconnect VPN IP phone

  Hi, hoping someone can shed some light on what I'm just more confused over trying to get by. Not sure if this goes in the section IP Telehpony or here...

  We have an ASA 5510 with the base license. We need to install IP phones to home teleworkers, and I understand there are Cisco IP phones that have built-in VPN clients to enable a tunnel to the central private network. IT seems that you can't use Anyconnect VPN to do this, and I am trying to establish what upgrade licenses, we must apply to the ASA, as both Anyconnect licenses that you get for free on the SAA is not enough.

  This is the phone that we seek;

  http://www.Cisco.com/en/us/prod/collateral/voicesw/ps6788/phones/ps10499/ps11005/data_sheet_c78-603725.html

  I want to know is the Anyconnect Essentials license will work with these IP phones?

  When I do a version of the show,

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 50

  Internal hosts: unlimited

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 0

  GTP/GPRS: disabled

  SSL VPN peers: 2

  The VPN peers total: 250

  Sharing license: disabled

  AnyConnect for Mobile: disabled

  AnyConnect for Linksys phone: disabled

  AnyConnect Essentials: disabled

  Assessment of Advanced endpoint: disabled

  Proxy sessions for the UC phone: 2

  Total number of Sessions of Proxy UC: 2

  Botnet traffic filter: disabled

  This platform includes a basic license.

  It shows "AnyConnect for Linksys phone: Disabled", it is the same for the Cisco IP phones? It is the kind of specific license, should I seek for Anyconnect on IP phones or will Essentials?

  Hi Leo,

  you will need 2 licenses: an Anyconnect Premium license and a permit «Anyconnect of Cisco VPN phone»

  ASA 8.2 and earlier license "for Cisco VPN Phone" has been named "for phone Linksys' it's the same.

  CFR. http://www.Cisco.com/en/us/docs/security/ASA/asa84/license/license_management/license.html#wp1487574

  HTH

  Herbert

• CS-mars does support ASA 5500 with version 8.4?

  Dear all,

  My mars is not able to discover devices Cisco ASA cisco ASA 5550 with last fact IOS is compatible with the CS March...

  Thanks in advance...

  Selva

  After some googleing I found that it is not supported...

  For more information, see link below

  http://www.Cisco.com/en/us/docs/security/security_management/CS-Mars/6.1/compatibility/local_controller/dtlc6x.html#wp85319

  HTH,

  GKP

• ASA EzVPN with several remote subnets

  Hello world

  I'll have the challenge of EasyVPN installation based on ASA 5520, and ASA 5505 (with the ASA5505 as the vpnclient) with several networks behind the ASA 5505.

  Access by the network directly connected on the 5505 to the central site works very well.

  But the second network segment (which is behind a router on the directly connected network) cannot connect to the central site.

  I guess I need to specify that some sort of acl's to be able to do that.

  BTW we do not use tunneling split, because all traffic moves through the tunnel (no local internet access).

  The layout looks like this

  (--LAN--)-5520---5505-(--LAN1--)-ROUTER-(--LAN2--)-(WAN)-

  LAN1 and LAN connection works great through the EZVPN Tunnel.

  LAN2 connection to the LAN does not work through the Tunnel of EZVPN.

  Here is the configuration used so far (outside the normal SHEEP, groups of objects and stuff ISAKMP crypto):

  Client:

  vpnclient Server 10.x.x.x

  extension-mode network mode vpnclient

  EzVPN vpngroup vpnclient password *.

  vpnclient username user1 password *.

  vpnclient enable

  Crypto ipsec df - bit clear-df outdoors

  Server:

  internal EzVPN group strategy

  Group Policy attributes EzVPN

  allow to NEM

  allow password-storage

  tunnel-group EzVPN type ipsec-ra

  General characteristics of tunnel-group EzVPN

  Group Policy - by default-EzVPN

  IPSec-attributes tunnel-group EzVPN

  pre-shared key *.

  user user1 password *.

  I hope you can help

  Best regards

  Jarle

  Unfortunately, it is not supported on the platform of the SAA. With EasyVPN on the SAA, only the connected networks can be advertised. To accomplish what you want to do, you need to configure a static IPSec tunnel and announce local networks via ACL interesting traffic. You can also use an IOS device that does not have the capabilities of "multiple subnet" with EasyVPN.

  http://www.Cisco.com/en/us/docs/iOS/sec_secure_connectivity/configuration/guide/sec_easy_vpn_rem.html#wp1098057

• ASA 5510 with AIP SSM-10

  I'm new to network administration and our company has an ASA 5510 with and map AIP SSM-10. On the interface ASA when I try to load Intrusion detection, he said the following:

  "For IPS 5.1 (1) S205.0, use the link below to access the IPS Device Manager." (If the SSM management IP address or the port is translated, replace them accordingly in the below URL). IPS 6.0.1 or above will be fully interated ASDM. »

  Unfortunately, no URL is displayed below this message and there is no documentation in the company that owns this configuration. Is there a way to reset the AIP without resetting the ASA? How can I find the IP address to be able to configure it?

  The ASA CLI, you will be able to check the IP address of the AIP module:

  view the details of the module

  It will show you the ip address of mgmt of the module, and you can https to the IP address of your PC.

• Downgrade the OS from Windows 7 to Windows XP, with license too

  I can active Windows 7 Pro license in the Windows XP operating system? Or do I need key separate license for Downgrade Windows 7 to Windows XP? I have Windows 7 Pro OEM version with license. I can downgrade to Windows XP with the Windows 7 disc and the license.

  Masud

  Because it's a downgrade, you can only use one version at a time. So if you are downgrading to Windows XP, you can have that version installed on this machine. (That is if you buy an OEM which entitles demotion). If you buy your own commercial version full Windows XP license, you can run Windows XP and Windows 7 at the same time in dual-boot.

  If you run Windows 7 and Windows XP at the same time, why not use the free Windows Virtual PC with Windows XP Mode available for Windows 7 Professional customers?

  Also, Windows XP Mode includes a full license of Windows XP Professional Service Pack 3.

  If you need to replace Windows 7 with Windows XP OEM System Builder, you will need to provide your own license.

  -----------------------

  How dual boot Windows 7 and Windows XP
  http://notebooks.com/2011/02/01/how-to-dual-boot-Windows-7-and-Windows-XP-Part-1/

  Run in Windows XP Mode requires:
  (1) Windows 7 Professional, Ultimate or Enterprise (not supported in Home Premium).

  Windows XP Mode and Windows Virtual PC
  http://www.Microsoft.com/Windows/Virtual-PC/default.aspx

  Windows XP Mode now accessible to more than PC
  http://windowsteamblog.com/Windows/archive/b/Windows7/archive/2010/03/18/Windows-XP-mode-now-accessible-to-more-PCs.aspx

  Get started with Windows Virtual PC
  http://www.Microsoft.com/Windows/Virtual-PC/get-started.aspx

  http://www.notebooks.com/2009/11/23/using-Windows-Virtual-PC-with-Windows-XP-mode/

• Can we do update content continues with licensed "professional"?

  Hello

  Looking to launch a magazine (NOT on newsstands) app to a customer which includes a continuous section, probably every two days, the items updated.  Is this something I could do with licensed "professional"?  Or is it something which is not feasible with a level of "enterprise"?

  Any advice greatly appreciated!

  Thank you

  Ian

  There are more two licenses separated from DPS. There is that one option that includes all the features and the price is according to your needs on a per client basis. Click on the request of consultation in link Digital Publishing Suite help | DPS pricing options to receive a quote for your project.

  You can update your folios as often as you want. It might better/more easy to use a CMS effective DPS of workflows based on CMS systems | Adobe Developer Connection.

• Upgrade to ESXi (free) 3.5 to ESX 4.1 (with license)

  Hello

  Can I switch from ESXi (free) 3.5 to ESX 4.1 (with license)?

  Yes, I need to change for ESX ESXi.

  Is possible?

  Thank you

  Can I switch from ESXi (free) 3.5 to ESX 4.1 (with license)?

  Yes, I need to change for ESX ESXi.

  Is possible?

  Either way - ESX, ESXi and ESXi for ESX - requires a new installation of the operating system, there is no way to upgrade (regardless of the licensing). In case you have a data store VMFS on the drive where you install the operating system, you must back up (or migrate) and restore the virtual machine.

  I suggest that you create separate logical volumes to the OS (~ 20 GB) and the VMFS. This way you can switch back from ESX to ESXi in the future without the need to evacuate VMs. As you may know, ESX 4.1 is the latest version with the Service Console.

  André

• AnyConnect 4.0 license with ASA-5515-FPWR

  Hi all

  I have a small question, where I can't find a clear answer for:

  A customer wants to buy a new ASA for a showroom. He wants to connect 30 phones VPN and 60 VPN users, where only 10 of them are simultaneously connected. Then we would have two choices now

  -Either go with the 3.5 Anyconnect licensing, with a premium SSL 50 license and activation phones VPN and mobility AC licenses

  - Or go to AC 4.0 license, where we would have to license 100 users with MORE licenses.

  My questions are:

  -Can I any other / more license on the SAA (i.e. SSL)

  -Where to install the license

  -How is the number of users (i.e. of the ad groups, local accounts)

  Is there a documentation clearly indicating the answers

  Thank you all for your help.

  If you want that the phone itself to be the endpoint remote VPN access, then Yes - you need VPN phone license which requires in turn AnyConnect Premium (for 3.x installations)

  "Plus" AnyConnect (for 4.x) includes 'VPN functionality for PC and mobile platforms, including per-app VPN on mobile platforms and phone Cisco VPN' (referring to the January 2015 of the ordering Guide AnyConnect 4.0 version)

• The services configuration of firepower on Cisco asa 5506 with ASDM

  I have a few 5506 firewalls, and they are fully licensed with services of power, control, Protection, URL filtering, malware. I have intend running and configuration of all of this on the 5506 by ASDM. I was wondering if there are guides for a basic configuration and the implementation of policies available. Something to show a basic configuration which would technically begin inspection of traffic and work. Then I can edit and make changes to my taste.

  Thank you

  My recommendation to clients is to look at the Cisco Live, BRKSEC-2018presentation. Please refer to the 56 slide from for a good overview of how policies are installed in a module of firepower.

  There are also a number of other detailed guides available in the FireSIGHT Management Center product support page should you care to learn more about customization and operations. You can also find the series of videos of ASA FirePOWER on request to Labminutes.com useful to guide you on execution of operations of your system.

• ASA 5500 x IPS license to the license of firepower

  I recently attended a webcast Cisco and told me that it is possible to obtain a free migration since the IPS license inherited the firepower license if you have a 5500 Series x ASA.  Nobody is able to successfully get the free conversion?

  There is a program of technological Migration offering that gives a discount on upgrades, but I have not heard of any offer of free migration.

• Cisco ASA 5508 with firepower of speeds VPN

  Nice day

  Can someone tell me which is better performance Anyconnect VPN or Cisco VPN?, I intend to use a VPN for my users to connect and transfer files to a shared folder speed does.

  Also, I don't want my clients to access a Web page or portal to get the client I can install the VPN client on the client labtop.

  Is it possible to do this as well?

  Hello

  The shared screenshot has the correct option is selected.

  Yes anyconnect supports IPSEC thus:

  https://supportforums.Cisco.com/discussion/11501221/Cisco-AnyConnect-DOE...

  http://www.Cisco.com/c/en/us/support/docs/security/AnyConnect-secure-mob...

  Please visit this link for the plug ASA 5508-firepower:

  http://www.Cisco.com/c/en/us/products/collateral/security/ASA-5500-serie...

  Kind regards

  Aditya

  Please evaluate the useful messages and mark the correct answers.