ASA dynamic Crypto map
I was looking at this example and did not have a clear explanation about the use of the
tunnel-group DefaultL2LGroup
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080b3d511.shtml
Why is the pre-shared-key * different pre-shared key talks about cisco123 ? What is a wild card to accept any
identification key by spoke them? Can it be set or is set as it is? I don't see the advantage if it's 'accept all '.
Thank you
Pete
Pete,
"*" is how ASA will display a key, it is hidden when you list the running configuration.
bsns-asa5505-19# conf t
bsns-asa5505-19(config)# tunnel-group BERN ipsec-attributes
bsns-asa5505-19(config-tunnel-ipsec)# ikev1 pre-shared-key 1234556778
bsns-asa5505-19(config-tunnel-ipsec)# sh run tunnel-group BERN ipsec-attri
tunnel-group BERN type remote-access
tunnel-group BERN ipsec-attributes
ikev1 pre-shared-key *****
There is no 'accept all' in IKE given that this key will be used to protect and decode identities of IKE.
Also, take a look in the tunnel-group mapping.
At a glance by default, tunnel groups are used as a last ditch effort in the match. That is, they will receive most of the peers with IPs dynamic (or unspecified).
M.
Tags: Cisco Security
Similar Questions
-
Dynamic Crypto map &; Defaultl2lGroup
Dear all,
How Defaultl2lGroups & dynamic crypto of the cards can be configured in an asa.
Why I need?
All our stores because asa 5505 (with dynamic ip addresses) are connected to the network head asa 5550 via dynamic vpn and headboard has 2 ISPS.
In fact, we have two lease lines a primary and another backup. Surprisingly, we have only a single subnet on the inside. Now that the main link BW is fully occupied. I want to use the help link too. I wonder if I can have several dynamic cryptographic cards & several groups default tunnel. While I can define servers in one vlan and users in other VLANs. and with two dynamic crypto & default tunnel grps I think passing a subnet (part of the 1st dynamic default crypto & 1 tunelgrp) and second subnet on the other link (2nd dynamic crypo & 2nd tunel default grp). This way the user vpn and internet traffic wil go through 1 link and vpn servers and internet traffic will pass through second link as both the subnet vpn will have another link as backup to each other.
Please provide us with the possibilities.
Please share your ideas.
Help, please.
Thanks in advance,
Kind regards
Jean Michel
Hi Sr,
1 default policy
Up to 65535 crypto map entries (including static and dynamic)
Be sure to note all the useful messages.
For this community, which is as important as a thank you.
-
Dynamic crypto several cards on the interface
I have an ASA 5540 executes code 8.2. The firewall has tunnels, VPNS, IPSec standard on this remote access VPN and SSL VPN without client.
I have 1921 Cisco routers with 4 G wireless cards must open dynamic VPN with the ASA 5540, so it seems that I need to implement a solution of EzVPN here.
My question is, multiple dynamic crypto maps are supported on a single interface?
For example, the current configuration of lists
PFS set 20 crypto dynamic-map outside_dyn_map Group 1
Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
In addition to cryptographic cards for static L2L tunnels.
I guess when I add the EzVPN I have to create a new dynamic map. After having done that, simply add something like that?
card crypto outside_map 65534 ipsec isakmp dynamic outside_new_map
Basically a different sequence number and card name?
Hi Colin,
It is fundamentally correct, that you will encounter some problems on incoming connections, two on the external interface dynamic crypto map entries.
One possibility would be to include a return address for correspondence for you EZ - VPN, for example, generously describe the Remote LAN as the destination of the encryption access list.
For example if your remote LAN is all within the range 10.66.0.0/16 set up an access as list:
outside_new [local area network] ip access list allow [local mask] 10.66.0.0 255.255.0.0
and include it in you card crypto dynamic outside_new_map
PFS set 20 crypto dynamic-map outside_new_map Group 1
Crypto-map dynamic outside_new_map 20 the value transform-set ESP-3DES-SHA
crypto dynamic-map outside_new_map 20 the value corresponds to the address outside_new
See also:
http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/IKE.html#wp1042880
-
IOS mixed Crypto Maps with Checkpoint Firewall
I have a config encryption that works very well with a remote CheckPoint Firewall:
-------------- \/ CONFIG 1 \/--------------------
crypto ISAKMP policy 5
BA 3des
md5 hash
preshared authentication
!
ISAKMP crypto key address 1.2.3.4 cryptokey1
!
Crypto ipsec transform-set esp-3des esp-md5-hmac txfrmset1
!
crypto dynamic-map vpn Dynamics 10
Set transform-set txfrmset1
!
secure1_in card crypto ipsec isakmp 1
defined by peer 205.245.184.2
Set transform-set txfrmset1
match address 105
!
IP nat inside source overload map route sheep interface Ethernet0
!
sheep allowed 10 route map
corresponds to the IP 110
!
access-list 105 permit ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255
------------/\ CONFIG 1 /\ --------------------
I need to add a card for remote clients using the Cisco VPN 3.6 client.
I have a card encryption that has worked great for me in the past. The combination
Both looks like this:
---------------\/ CONFIG 2 \/ --------------------------
Nine AAA
AAA authentication login userauthen local
AAA authorization groupauthor LAN
crypto ISAKMP policy 5
BA 3des
md5 hash
preshared authentication
!
crypto ISAKMP policy 10
BA 3des
md5 hash
preshared authentication
Group 2
!
cryptokey1 key crypto isakmp address 1.2.3.4 No.-xauth
!
Crypto ipsec transform-set esp-3des esp-md5-hmac txfrmset1
!
crypto dynamic-map vpn Dynamics 10
Set transform-set txfrmset1
ISAKMP crypto client configuration group remote1
cryptokey2 key
DNS 10.0.0.4
WINS 10.0.0.5
VPN-pool
!
card crypto client secure1_in of authentication list userathen
card crypto isakmp authorization list groupauthor secure1_in
client configuration address card crypto secure1_in answer
secure1_in map ipsec-isakmp crypto 5
defined peer 1.2.3.4
Set transform-set txfrmset1
match address 105
vpnclient 10-isakmp ipsec vpn dynamic-dynamic crypto map
!
IP VPN-pool pool 172.16.30.1 room 172.16.30.254
IP nat inside source overload map route sheep interface Ethernet0
access-list 105 permit ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255
!
access-list 110 deny ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255
access-list 110 permit ip 192.168.0.0 0.0.0.255 any
!
sheep allowed 10 route map
corresponds to the IP 110
---------------/\ CONFIG 2 /\---------------------------
It's classic crypto right out of the playbook of Cisco. This card works
very well with the Cisco VPN client, but produced the following errors after a
successful with Checkpoint Firewall P1 installation:
--------------\/ ERROR OUTPUT \/ -----------------------
05:13:02: ISAKMP (0:2): send package to 1.2.3.4 (R) MM_KEY_EXCH
05:13:02: ISAKMP (0:2): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Former State = new State IKE_R_MM5 = IKE_P1_COMPLETE
05:13:02: ISAKMP (0:2): need to config/address
05:13:02: ISAKMP (0:2): need to config/address
05:13:02: ISAKMP: node set 1502565681 to CONF_ADDR
05:13:02: ISAKMP (0:2): pool of IP addresses not defined for ISAKMP.
05:13:02: ISAKMP (0:2): node 1502565681 error suppression FALSE reason «»
05:13:02: ISAKMP (0:2): entry = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
Former State = new State IKE_P1_COMPLETE = IKE_CONFIG_MODE_SET_SENT
05:13:02: ISAKMP (0:2): 1.2.3.4 received packet (R) CONF_ADDR
05:13:02: ISAKMP: node set-1848822857 to CONF_ADDR
05:13:02: ISAKMP (0:2): entry unknown: status = IKE_CONFIG_MODE_SET_SENT, major, minor = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
05:13:04: ISAKMP (0:2): 1.2.3.4 received packet (R) CONF_ADDR
--------------/\ ERROR OUTPUT /\--------------------------
This does not happen to config 1. If it's a PIX, I would use the
No.-config-mode keyword after the No.-xauth on isakmp crypto "key."
command line. It is not available on IOS IPSEC and I have never
needed to do before. I am running Cisco IOS 12.2 (5.4) T on a VPN of 1721
router. The static map seems to work by itself. What I am doing wrong?
I saw her a couple of times and to be honest have never taken down to an exact cause, although in this case it looks like almost to the point of control request an IP address which is weird. Try the following:
1. Add "card crypto secure1_in client configuration address to initiate" and see what it does.
2. try 12.2 (8) code T5 with it, I had a previous user running 12.2 (11) T and we got the same error messages, returning to this level of code it is resolved.
In addition, you wouldn't need:
> access-list 110 deny ip 192.168.10.0 0.0.0.255 172.16.30.0 0.0.0.255
for example, so that you do not NAT client VPN traffic?
-
8.2 ASA dynamic VPN to ASA static config help
Hello
I'm trying to set up a tunnel l2l between an ASA and ASA remote central where the remote receives a DHCP provider address.
ASA Remote Config:
interface Vlan1
nameif inside
security-level 100
IP 10.10.10.1 255.255.255.0
# Receives an IP address of 90.0.1.203 from the provider.
interface Vlan2
nameif outside
security-level 0
IP address dhcp setroute
the Corp_Networks object-group network
object-network 172.16.0.0 255.240.0.0
object-network 10.0.0.0 255.0.0.0
object-network 192.168.252.0 255.255.255.0
access-list SHEEP extended ip 10.10.10.0 allow 255.255.255.0 Corp_Networks object-group
Remote access ip 10.10.10.0 extended list allow 255.255.255.0 Corp_Networks object-group
NAT (inside) 0 access-list SHEEP
NAT (inside) 1 0.0.0.0 0.0.0.0
outdoor 10.0.0.0 255.255.255.0 90.0.1.1
Route outside 172.16.0.0 255.240.0.0 90.0.1.1
Route outside 192.168.252.0 255.255.255.0 90.0.1.1
Crypto ipsec transform-set esp-3des esp-sha-hmac ToCorp
outside_map card crypto 10 corresponds to the Remote address
outside_map 10 peer Public_address crypto card game
card crypto outside_map 10 game of transformation-ToCorp
life safety association set card crypto outside_map 10 28800 seconds
card crypto outside_map 10 set security-association life kilobytes 4608000
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 864000
No encryption isakmp nat-traversal
tunnel-group Public_address type ipsec-l2l
IPSec-attributes tunnel-group Public_address
pre-share-key Council
ASA company Config:
the Corp_Networks object-group network
object-network 172.16.0.0 255.240.0.0
object-network 10.0.0.0 255.0.0.0
object-network 192.168.252.0 255.255.255.0
access-list allowed extensive sheep object-group Corp_Networks 10.10.10.0 ip 255.255.255.0
access-list ToRemote allowed ext object-group ip Corp_Networks 10.10.10.0 255.255.255.0
NAT (inside) 0 access-list sheep
Route outside 10.10.10.0 255.255.255.0 Public_Gateway
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
ToRemote game Dynamics-card 65530, crypto transform-set ESP-3DES-SHA
outside_map map 8-isakmp dynamic ipsec ToRemote crypto
outside_map interface card crypto outside
crypto ISAKMP policy 20
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IPSec-attributes tunnel-group DefaultL2LGroup
pre-shared-key *.
Output of remote endpoint:
ISAKMP crypto #sh her
ITS enabled: 1
Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
Total SA IKE: 1
1 peer IKE: Public_Address
Type: L2L role: initiator
Generate a new key: no State: MM_ACTIVE
#sh crypto ipsec his
Interface: outside
Tag crypto map: outside_map, seq num: 10, local addr: 90.0.1.203
Hawaii2Avid to access extended list ip 10.10.10.0 allow 255.255.255.0 10.0.0.0 255.0.0.0
local ident (addr, mask, prot, port): (10.10.10.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (10.0.0.0/255.0.0.0/0/0)
current_peer: Public_address
#pkts program: 616, #pkts encrypt: 616, #pkts digest: 616
#pkts decaps: 22, #pkts decrypt: 22, #pkts check: 22
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 616, #pkts comp failed: 0, #pkts Dang failed: 0
success #frag before: 0, failures before #frag: 0, #fragments created: 0
Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
#send errors: 0, #recv errors: 0
local crypto endpt. : 90.0.1.203/4500, remote Start crypto. : Public_address/4500
Path mtu 1500, fresh ipsec generals 66, media, mtu 1500
current outbound SPI: D6A48143
current inbound SPI: E0C4F32A
SAS of the esp on arrival:
SPI: 0xE0C4F32A (3771003690)
transform: esp-3des esp-sha-hmac no compression
running parameters = {L2L, Tunnel, NAT-T program,}
slot: 0, id_conn: 36864, crypto-card: outside_map
calendar of his: service life remaining (KB/s) key: (3914994/28098)
Size IV: 8 bytes
support for replay detection: Y
Anti-replay bitmap:
0 x 00000000 0x007FFFFF
outgoing esp sas:
SPI: 0xD6A48143 (3601105219)
transform: esp-3des esp-sha-hmac no compression
running parameters = {L2L, Tunnel, NAT-T program,}
slot: 0, id_conn: 36864, crypto-card: outside_map
calendar of his: service life remaining (KB/s) key: (3914952/28098)
Size IV: 8 bytes
support for replay detection: Y
Anti-replay bitmap:
0x00000000 0x00000001
Tag crypto map: outside_map, seq num: 10, local addr: 90.0.1.203
Hawaii2Avid to access extended list ip 10.10.10.0 allow 255.255.255.0 172.16.0.0 255.240.0.0
local ident (addr, mask, prot, port): (10.10.10.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (172.16.0.0/255.240.0.0/0/0)
current_peer: Public_Address
#pkts program: 406, #pkts encrypt: 406, #pkts digest: 406
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 406, model of #pkts failed: 0, #pkts Dang failed: 0
success #frag before: 0, failures before #frag: 0, #fragments created: 0
Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
#send errors: 0, #recv errors: 0
local crypto endpt. : 90.0.1.203/4500, remote Start crypto. : Public_Address/4500
Path mtu 1500, fresh ipsec generals 66, media, mtu 1500
current outbound SPI: 1BE239F9
current inbound SPI: AC615F8D
SAS of the esp on arrival:
SPI: 0xAC615F8D (2892062605)
transform: esp-3des esp-sha-hmac no compression
running parameters = {L2L, Tunnel, NAT-T program,}
slot: 0, id_conn: 36864, crypto-card: outside_map
calendar of his: service life remaining (KB/s) key: (3915000/28095)
Size IV: 8 bytes
support for replay detection: Y
Anti-replay bitmap:
0x00000000 0x00000001
outgoing esp sas:
SPI: 0x1BE239F9 (467810809)
transform: esp-3des esp-sha-hmac no compression
running parameters = {L2L, Tunnel, NAT-T program,}
slot: 0, id_conn: 36864, crypto-card: outside_map
calendar of his: service life remaining (KB/s) key: (3914973/28092)
Size IV: 8 bytes
support for replay detection: Y
Anti-replay bitmap:
0x00000000 0 x 000000000
We just seems stuck at this point and can't seem to get the traffic going back and forth, even if the tunnel does not seem to be connected. The only concern I see is pkts getting encrypted but none decrypts. It is usually something to do with the acl, but this one is pretty simple.
Thank you
-Geoff
Please check if you have any other card/LAN-to-LAN crypto configured on the ASA Corporate where the crypto ACL may overlap.
If you can share the map full encryption as well as the ACL of the ASA Corporate crypto, we can check for you.
Misspelling of the ASA remote path statement:
outdoor 10.0.0.0 255.255.255.0 90.0.1.1
I understand that you want to access the full class on the site of the company, where the road should say:
external route 10.0.0.0 255.0.0.0 90.0.1.1
-
Hi all
I try to have several VPN site-to-site hooked to my Interface Outside one.
I understand that I may have a crpypto card assigned to the interface.
If I want to for example, one of virtual private networks to require PFS but either not to do it-just set a different priority under the Crypto map? Map crypro entries get transformed top to bottom until a match is found?
for example
CMAP 10 ipsec-isakmp crypto card
defined peer x.x.x.x
game of transformation-TSET
match address ACL1Crypto map CMAP 20 ipsec-isakmp
defined peer y.y.y.y
game of transformation-TSET
match address ACL2
set the pfs Group 2Thank you
You're right, the encryption card is dealt top-down. So if your traffic is ACL2 (and not ACL1!), then all settings configured under sequence CMAP 20 are relevant in this regard.
-
role of the crypto map sequence number
I'm setting up IPSEC in four sites in a manner completely mesh. The problem I have is one of the sites is our main hub and everything works on a class B network. Creating ACL to get from one place to another is relatively simple, but getting a site on the main hub is another story, because other sites are all the subnets in the class B address, I have to remove these subnets of a class B and at the same time to encrypt the rest of the class B address. Subnets of the smaller sites are for most of the 24 and 25. I was wondering if the sequence # in the card order crypto could play a role for me. If I set the priority on small sites and put the lower on the map pointing to the main pole encryption could I get away with something like this:
licence (local subnet) 0.0.0.255 x.x.x.x where x.x.x.x (category B) 0.0.255.255
Thanks in advance for taking the time.
Mario
Mario... that's exactly how it works for the two ISAKMP Crypto map policies and policy. It will look at the lowest number (like attentive) so if you do your remote sites all a higher priority (lower number), then you should be fine with respect to the central site.
Kind regards
-
2 crypto maps to the external interface? Possible?
Hi, I have a little problem with a PIX 515 UR on FOS 6.3 (1).
What I'm trying to do is to run 2 VPN site to site to him. The thing is: although I can get two separate crypt cards into the config, its only the more recent which is active when I do a ' sh crypto his '.
Anyone have any ideas?
TIA-
Gary
I do multiple like this:
I have the main Board, applied externally:
toXXXX interface card crypto outside
Then, I build maps more screaming like ACL if:
toXXXX 20 ipsec-isakmp crypto map
card crypto toXXXX 20 match address no_nat (name of the ACL)
card crypto toXXXX 20 peers set x.x.x.x
toXXXX 20 transform-set mytrans crypto card
life safety association set card crypto toXXXX 20 seconds 3600 4608000 kilobytes
toXXXX 40 ipsec-isakmp crypto map
card crypto toXXXX 40 correspondence address toACME (name of the ACL)
card crypto toXXXX 40 peers set x.x.x.x
toXXXX 40 transform-set mytrans crypto card
life safety association set card crypto toXXXX 40 seconds 3600 4608000 kilobytes
-
How can I get the engine working in the ASA 5505 Crypto
I bought a brand new ASA 5505 to connect to the Cisco 3640 and I can not yet set up the tunnel. I have tried to change the set of transformation to just but know luck. I recently put a VPN using DMVPN and Cisco 501 in a site-to-site, but it has been wondering what happens.
The router (3640 executes code 12.4) seems ok and I don't think I have a problem with the router with Cisco 501 great work.
This is a laboratory environment.
This is the function defined on the ASA 5505
The devices allowed for this platform:
The maximum physical Interfaces: 8
VLAN: 3, restricted DMZ
Internal guests: 10
Failover: disabled
VPN - A: enabled
VPN-3DES-AES: enabled
Peer VPN: 10
WebVPN peers: 2
Double ISP: disabled
Junction ports VLAN: 0
AnyConnect for Mobile: disabled
AnyConnect for Linksys phone: disabled
Assessment of Advanced endpoint: disabled
This platform includes a basic license.
This is a ping from 10.3.4.10 to 10.1.1.1. He said nothing about IPSEC or ISAKMP.
That's what I get when I do the: show crypto ipsec his
ASA5505 (config) # show crypto ipsec his
There is no ipsec security associations
ASA5505 (config) # show crypto isakmp his
There is no isakmp sas
Debug crypto isakmp 10
entry packets within the icmp 10.3.4.10 8 0 10.1.1.1 detail
I have worked on it for a week and don't really know if I have a bad ASA5505. Since the normal stuff like browsing the Internet works and I can ping to the outside and inside, I don't know what to think. See attachments.
"Do what you asked has worked.
Nice to hear that your problem is solved.
"My question is can I use the transform-set ESP-3DES-SHA instead of MD5?"
Of course you can.
Kind regards.
Please do not forget to note the useful messages and check "Solved my problem", if the post has solved your problem.
-
ASA-dynamic to static VPN fails
I have an ASA 5510 with an address of STIC and a 5505 with a dynamics.
I created a dynamic the 5510 virtual private network. When the 5505 with it's dynamic address, tried to connect with me, I get the following errors:
' Mar 25 05:45:14 [IKEv1]: IP = 213.137.6.203, message received ISAKMP Aggressive Mode 1 with the name of the unknown group tunnel ' 213.137.6.203 '.
Mar 25 05:45:14 [IKEv1]: Group = DefaultRAGroup, IP = 213.137.6.203, Removing peer to peer table does not, no match!
Mar 25 05:45:14 [IKEv1]: Group = DefaultRAGroup, IP = 213.137.6.203, error: cannot delete PeerTblEntryI also get a similar error 5505 a aggressive Mode disabled
Looks like the 5510 believes it is an application for connection (site-to-site) L2L as opposed to a connection established dynamically. It doesn't have a group of tunnel for 213.137.6.203. You can create a group of tunnel with that name to resolve this problem.
The other option is to implement the ASA for a remote access connection (for example, Easy VPN).
Here's a URL that describes how to configure Easy VPN with NEM and L2L. HTH
http://www.Cisco.com/application/PDF/paws/100313/pixasa_easy_l2l_vpn.PDF
-
Dear all!
I have a setup of RA - VPN with a Cisco VPNC and a Cisco Secure ACS 4.2. I do VPN tunnel-group mapping clears the user to class attributes 25 RADIUS (OU =...), and it works fine. I migrated this solution since the VPNC to an ASA5520 with 8.0 software image (4) and I just can't do this mapping of tunnel-group, although ACS configuration is the same (of course) and I think that FW configuration is correct also.
All tunnel groups internal and authentication is just everywhere, but the tunnel projection is not working.
Can someone email me an example configuration for ASA to check?
Y at - it a special order (e.g. "tunnel-Group-map enable or") should I use?
Thanks for the replies!
By (e)
Miki
The pools and ip addresses can be either set on the group policy with the correct value, or you can use the ACS with either a static ip address on the user or with the pool on the group or user, this attribute will be passed on to the RADIUS access accept as a framed ip address value.
-
supported vs IPSec VRF taking crypto maps for several tunnels
Hi all!
I came to know that we can use the same public ip address for the creation of several tunnels to different websites using crypto-cards featuring many lines each representing a reference to a particular tunnel and using vrf aware IPsec, but I would like to know what are the differences / advantages / cautions.
Thanks for your time
Murali.
Murali
That I understand the feature essentially allows you to have multiple IPSEC tunnels and traffic in the tunnel that is to say. source and destination IP of the high-end devices can be in different VRF.
So it works mainly with the MPLS VPN IE. If you had several MPLS VPN each with their own VRF you can then run ISPEC tunnels on the MPLS network and when packets are received, they are automatically in the correct VRF.
You could not do that normal crypto cards IE. You can cancel again several IPSEC tunnels on a public IP address but then everything would be traffic in the same global routing table.
If the benefit is basically the same that you get with any VRF installation IE. logical separation of traffic on a single device.
Can't really say much about the warnings as I've never used it but there are some restrictions.
See this link for more details-
Jon
-
ASA 5505 - crypto isakmp nat-traversal is missing?
I can't understand it. I have an ASA5505 at home that I use for VPN access. Sometimes when I connect I can't ping anything. I check the config and it shows:
No encryption isakmp nat-traversal
I have configured "crypto isakmp nat-traversal" so many times before, and somehow it is still deleted. Seems to happen at random, as well as when the device is restarted. (Yes, the config has been saved). I would say that what is happening at least 2 - 3 times a week.
Any ideas? I am running the 8.0.2 version code.
This is a bug. Set the value on something other than the default value of 20. This will fix the problem.
Cryto isakmp nat-traversal 21
-
Encryption: "Apply crypto map interface.
East - the best forum to discuss encryption?
I want to implement a single aes encryption between an ISDN Bri1/0 port on a 2611xm and a 2811.
I want to encrypt everything except telnet on the ISDN link between these routers. I want to telent between routers just in case the encryption locks himself. This is my requirement of customers.
Question #1: Should I contact the card encryption the Ethernet port (as I have seen in many examples) or on the ISDN connection?
Question #2: If I ask the encryption card to the ISDN connection, should I do the encryption the BRI port card or the dialer?
Question #3: Assuming that both routers and all segments use the 10.0.0.0 network and are not connected to what anyone else, the following access list would work?
access list 110
deny ip any eq telnet
allow an ip
Thank you
Mark
Hi Mark,
Apply the card encryption to your outgoing interface (Dialer)
You probably will lock the router by putting
an ip address allowed any one in your crypto access list
you have probably even to add telnet deny entry in your access list if you are ready to open your session to the router
I suggest you
extended to remote IP access list
deny ip any eq telnet
ip licensing 10.0.1.0 0.0.0.255 10.0.2.0 0.0.0.255
The remote site would have a mirror
social-seat extended IP access list
deny ip any eq telnet
IP 10.0.2.0 allow 0.0.0.255 10.0.1.0 0.0.0.255
-
Hi there, I've never had this problem when I bought my MBP in 2010, but after the problem with unexpected reboots of El Capitan passage has become more common and is really affecting the productivity of my laptop.
For clarity, here's my cell phone information:
MacBook Pro (15-inch, mid 2010)
Processor: Intel Core i5 2.53 GHz to
Memory: 8 GB 1067 MHz DDR3
Graphics card:
integrated - Intel HD Graphics 288 MB
discreet - NVIDIA GeForce GT 330 M 256 MB
I ran the the Apple Hardware Test with no problems found. After looking on the forums and identifying the problem I installed gfxCardStatus to keep the graphics card using only internally, however, some programs force the use of Nvidia, which translates as the unexpected restarts.
The latest report of panic is attached below:
In any case, it is quite upsetting that after spending thousands of dollars on apple and laptops high-end, these problems are properly does not recognize their existence. After discussing with them several times they fail to take responsibility, when it is clearly a case of defective material...
Any suggestions for managing at least this issue would be very useful.
Thank you
Philippe
Sam 5 17:01:31 dec 2015
Panic report *.
panic (cpu 1 0xffffff7f8ddf1bad appellant): "panic GPU: 7f [
] 3 3 0 0 0 0 3: NVRM [0 / 1:0:0]: error 0 x 00000100 reading: CFG 0xffffffff, 0xffffffff, 0xffffffff, BAR0 0xd2000000 0xffffff91277cf000 sControl-3.11.33.1/src/AppleMuxControl/kext/GPUPanic.cpp:127 P2/4\n"@/Library/Caches/com.apple.xbs/Sources/AppleGraphicsControl/AppleGraphic 0x0a5480a2, D0, Backtrace (CPU 1), frame: return address
0xffffff811461b0a0: 0xffffff800ace5307
0xffffff811461b120: 0xffffff7f8ddf1bad
0xffffff811461b200: 0xffffff7f8b97ffa4
0xffffff811461b2c0: 0xffffff7f8ba4cadd
0xffffff811461b300: 0xffffff7f8ba4cb48
0xffffff811461b380: 0xffffff7f8bcd1a23
0xffffff811461b4f0: 0xffffff7f8ba70b79
0xffffff811461b510: 0xffffff7f8b986cfd
0xffffff811461b5c0: 0xffffff7f8b984690
0xffffff811461b7c0: 0xffffff7f8b98576f
0xffffff811461b8a0: 0xffffff7f8d2810ea
0xffffff811461b8e0: 0xffffff7f8d290aa3
0xffffff811461b900: 0xffffff7f8d2bf3ea
0xffffff811461b940: 0xffffff7f8d2bf449
0xffffff811461b980: 0xffffff7f8d296642
0xffffff811461b9d0: 0xffffff7f8d2620ae
0xffffff811461ba70: 0xffffff7f8d25df51
0xffffff811461baa0: 0xffffff7f8d25bae5
0xffffff811461bae0: 0xffffff800b2e2057
0xffffff811461bb80: 0xffffff800b2e4828
0xffffff811461bbe0: 0xffffff800b2e1967
0xffffff811461bd20: 0xffffff800ada07d0
0xffffff811461be30: 0xffffff800ace9aa3
0xffffff811461be60: 0xffffff800accd478
0xffffff811461bea0: 0xffffff800acdcfd5
0xffffff811461bf10: 0xffffff800adc13aa
0xffffff811461bfb0: 0xffffff800adf4b36
Extensions of core in backtrace:
com.apple.driver.AppleMuxControl (3.11.33b1) [FF6CE9C5-9D8F - a 3, 48 - 9 d 10-2BB9C2DDD22 7]@0xffffff7f8dde3000-> 0xffffff7f8ddf6fff
dependency: com.apple.driver.AppleGraphicsControl (3.11.33b1) [4ADB751E-5208-3DA7-A8C3-E9EC07 263B16]@0xffffff7f8dddb000
dependency: com.apple.iokit.IOACPIFamily (1.4) [CBAE26D8-0ACB-3C1F-8347-FDCA67EC40B3] @0xfffff f7f8b7b4000
dependency: com.apple.iokit.IOPCIFamily (2.9) [8E5F549E-0055-3C0E-93F8-E872A048E31B] @ 7f8b52d000 0xffffff
dependency: com.apple.iokit.IOGraphicsFamily (2.4.1) [48AC8EA9-BD3C-3FDC-908D-09850215AA32] @0 xffffff7f8b8d2000
dependency: com.apple.driver.AppleBacklightExpert (1.1.0) [5CB7D4B7-B100-34EE-BD40-1EC07E865C 67]@0xffffff7f8ddde000
com.apple.nvidia.classic.NVDAResmanTesla (10.0) [05FC5D7E-BB0B-3232-BBBD-8A49B687 0D8B]@0xffffff7f8b929000-> 0xffffff7f8bb9efff
dependency: com.apple.iokit.IOPCIFamily (2.9) [8E5F549E-0055-3C0E-93F8-E872A048E31B] @ 7f8b52d000 0xffffff
dependency: ffff7f8b919000 @0xff com.apple.iokit.IONDRVSupport (2.4.1) [814A7F4B-03EF-384A-B205-9840F0594421]
dependency: com.apple.iokit.IOGraphicsFamily (2.4.1) [48AC8EA9-BD3C-3FDC-908D-09850215AA32] @0 xffffff7f8b8d2000
com.apple.nvidia.classic.NVDANV50HalTesla (10.0) [CA 56199, 6 - 3C8D - 3EBB - B5EF - 7B1B467 8ACF9]@0xffffff7f8bba9000-> 0xffffff7f8be56fff
dependency: com.apple.nvidia.classic.NVDAResmanTesla (10.0.0) [05FC5D7E-BB0B-3232-BBBD-8A49B6 870D8B]@0xffffff7f8b929000
dependency: com.apple.iokit.IOPCIFamily (2.9) [8E5F549E-0055-3C0E-93F8-E872A048E31B] @ 7f8b52d000 0xffffff
com.apple.GeForceTesla (10.0) [49982DF3-8146-3BD0-AD3F-A7E7AB5ACBB5] @0xffffff7f8d 240000-> 0xffffff7f8d30bfff
dependency: com.apple.iokit.IOPCIFamily (2.9) [8E5F549E-0055-3C0E-93F8-E872A048E31B] @ 7f8b52d000 0xffffff
dependency: ffff7f8b919000 @0xff com.apple.iokit.IONDRVSupport (2.4.1) [814A7F4B-03EF-384A-B205-9840F0594421]
dependency: com.apple.iokit.IOGraphicsFamily (2.4.1) [48AC8EA9-BD3C-3FDC-908D-09850215AA32] @0 xffffff7f8b8d2000
dependency: com.apple.nvidia.classic.NVDAResmanTesla (10.0.0) [05FC5D7E-BB0B-3232-BBBD-8A49B6 870D8B]@0xffffff7f8b929000
Corresponding to the current thread BSD process name: WindowServer
Mac OS version:
15B 42
Kernel version:
Darwin Kernel Version 15.0.0: Sat Sep 19 15:53:46 PDT 2015; root:XNU-3247.10.11~1/RELEASE_X86_64
Kernel UUID: AB5FC1B4-12E7-311E-8E6F-9023985D8C1D
Slide kernel: 0x000000000aa00000
Text of core base: 0xffffff800ac00000
Text __HIB base: 0xffffff800ab00000
Name of system model: MacBookPro6, 2 (Mac-F22586C8)
Availability of the system in nanoseconds: 1557747038609
last load kext to 69928374174: com.apple.driver.AudioAUUC 1.70 (addr 0xffffff7f8d537000 size 32768)
Finally unloaded kext to 240741317817: com.apple.driver.usb.AppleUSBUHCI 1.0.1 (addr 0xffffff7f8c248000 size 126976)
kexts responsible:
com.radiosilenceapp.nke.Filter 1.1
com.apple.driver.AudioAUUC 1.70
com.apple.driver.AppleHWSensor 1.9.5d0
com.apple.driver.AGPM 110.20.21
com Apple.filesystems.autofs 3.0
com.apple.driver.AppleOSXWatchdog 1
com.apple.driver.AppleMikeyHIDDriver 124
com.apple.driver.AppleMikeyDriver 272.50.31
com Apple.Driver.pmtelemetry 1
com.apple.iokit.IOUserEthernet 1.0.1
com.apple.driver.AppleUpstreamUserClient 3.6.1
com.apple.iokit.IOBluetoothSerialManager 4.4.2f1
com.apple.GeForceTesla 10.0.0
com.apple.driver.AppleHDA 272.50.31
com.apple.driver.AppleIntelHDGraphics 10.0.0
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.AppleHV 1
com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.4.2f1
com.apple.driver.AppleSMCPDRC 1.0.0
com.apple.driver.AppleMuxControl 3.11.33b1
com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0
com.apple.driver.AppleIntelSlowAdaptiveClocking 4.0.0
com.apple.driver.AppleMCCSControl 1.2.13
com.apple.driver.AppleIntelHDGraphicsFB 10.0.0
com.apple.driver.AppleSMCLMU 208
com.apple.driver.AppleLPC 3.1
com.apple.driver.SMCMotionSensor 3.0.4d1
com.apple.driver.AppleUSBTCButtons 245,4
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0
com.apple.BootCache 37
com.apple.driver.AppleUSBTCKeyboard 245,4
com.apple.driver.AppleUSBCardReader 3.7.1
com.apple.driver.AppleIRController 327,5
com.apple.iokit.SCSITaskUserClient 3.7.7
com.apple.iokit.IOAHCIBlockStorage 2.8.0
com.apple.driver.AirPort.Brcm4331 800.20.24
com.apple.driver.AppleFWOHCI 5.5.2
3.1.5 com.apple.driver.AppleAHCIPort
com.apple.iokit.AppleBCM5701Ethernet 10.1.11
com.apple.driver.usb.AppleUSBEHCIPCI 1.0.1
com.apple.driver.AppleSmartBatteryManager 161.0.0
com.apple.driver.AppleRTC 2.0
com.apple.driver.AppleACPIButtons 4.0
com.apple.driver.AppleHPET 1.8
com.apple.driver.AppleSMBIOS 2.1
com.apple.driver.AppleACPIEC 4.0
com.apple.driver.AppleAPIC 1.7
com.apple.driver.AppleIntelCPUPowerManagementClient 218.0.0
com Apple.NKE.applicationfirewall 163
com Apple.Security.Quarantine 3
com.apple.security.TMSafetyNet 8
com.apple.driver.AppleIntelCPUPowerManagement 218.0.0
com.apple.AppleGraphicsDeviceControl 3.11.33b1
com Apple.kext.Triggers 1.0
com.apple.iokit.IOSurface 108.0.1
com.apple.iokit.IOSerialFamily 11
com.apple.nvidia.classic.NVDANV50HalTesla 10.0.0
com.apple.nvidia.classic.NVDAResmanTesla 10.0.0
com.apple.driver.DspFuncLib 272.50.31
com.apple.kext.OSvKernDSPLib 525
com.apple.driver.CoreCaptureResponder 1
com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.4.2f1
com.apple.iokit.IOBluetoothFamily 4.4.2f1
com.apple.driver.AppleSMBusPCI 1.0.14d1
com.apple.driver.AppleBacklightExpert 1.1.0
com.apple.iokit.IONDRVSupport 2.4.1
com.apple.driver.AppleGraphicsControl 3.11.33b1
com.apple.driver.IOPlatformPluginLegacy 1.0.0
com.apple.iokit.IOSlowAdaptiveClockingFamily 1.0.0
com.apple.driver.AppleSMBusController 1.0.14d1
com.apple.iokit.IOFireWireIP 2.2.6
com.apple.driver.AppleHDAController 272.50.31
com.apple.iokit.IOGraphicsFamily 2.4.1
com.apple.iokit.IOHDAFamily 272.50.31
com.apple.iokit.IOAudioFamily 204,1
com.apple.vecLib.kext 1.2.0
com.apple.driver.IOPlatformPluginFamily 6.0.0d7
com.apple.driver.AppleSMC 3.1.9
com.apple.driver.CoreStorage 517
com.apple.driver.usb.IOUSBHostHIDDevice 1.0.1
com.apple.driver.AppleUSBMultitouch 250.4
com.apple.iokit.IOSCSIBlockCommandsDevice 3.7.7
com.apple.iokit.IOUSBMassStorageDriver 1.0.0
com.apple.iokit.IOUSBHIDDriver 900.4.1
com.apple.driver.usb.AppleUSBHostCompositeDevice 1.0.1
com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.7.7
com.apple.iokit.IOBDStorageFamily 1.8
com.apple.iokit.IODVDStorageFamily 1.8
com.apple.iokit.IOCDStorageFamily 1.8
com.apple.driver.usb.AppleUSBHub 1.0.1
com.apple.iokit.IOAHCISerialATAPI 2.6.2
com.apple.iokit.IOSCSIArchitectureModelFamily 3.7.7
1101.24 com.apple.iokit.IO80211Family
com Apple.Driver.corecapture 1.0.4
4.5.8 com.apple.iokit.IOFireWireFamily
com.apple.iokit.IOAHCIFamily 2.8.0
com.apple.iokit.IOEthernetAVBController 1.0.3b3
com.apple.driver.mDNSOffloadUserClient 1.0.1b8
com.apple.iokit.IONetworkingFamily 3.2
com.apple.iokit.IOUSBFamily 900.4.1
com.apple.driver.usb.AppleUSBEHCI 1.0.1
com.apple.iokit.IOUSBHostFamily 1.0.1
com.apple.driver.AppleUSBHostMergeProperties 1.0.1
com.apple.driver.AppleEFINVRAM 2.0
com.apple.driver.AppleEFIRuntime 2.0
com.apple.iokit.IOHIDFamily 2.0.0
com.apple.iokit.IOSMBusFamily 1.1
com Apple.Security.sandbox 300.0
com.apple.kext.AppleMatch 1.0.0d1
com.apple.driver.AppleKeyStore 2
com.apple.driver.AppleMobileFileIntegrity 1.0.5
com.apple.driver.AppleCredentialManager 1.0
com.apple.driver.DiskImages 415
com.apple.iokit.IOStorageFamily 2.1
com.apple.iokit.IOReportFamily 31
com.apple.driver.AppleFDEKeyStore 28.30
com.apple.driver.AppleACPIPlatform 4.0
com.apple.iokit.IOPCIFamily 2.9
com.apple.iokit.IOACPIFamily 1.4
com.apple.kec.Libm 1
com Apple.KEC.pthread 1
com Apple.KEC.corecrypto 1.0
Model: MacBookPro6, 2, MBP61.0057.B11 of BootROM, 2 processors, Intel Core i5 2.53 GHz, 8 GB, MSC 1.58f17
Graphics: integrated graphics card Intel HD, Intel HD Graphics,
Graphics card: NVIDIA GeForce GT 330 M, NVIDIA GeForce GT 330 M, PCIe, 256 MB
Memory module: DIMM0/0 BANK, 4 GB DDR3, 1067 MHz, 0x029E, 0x434D5341344758334D314131303636433720
Memory module: DIMM0/1 BANK, 4 GB DDR3, 1067 MHz, 0x029E, 0x434D5341344758334D314131303636433720
Airport: spairport_wireless_card_type_airport_extreme (0x14E4, 0 x 93), Broadcom BCM43xx 1.0 (5.106.98.100.24)
Bluetooth: Version 4.4.2f1 16391, 3 services, 27 aircraft, 1 incoming serial ports
Network service: Wi - Fi, AirPort, en1
Serial ATA Device: TOSHIBA MK5055GSXF, 500,11 GB
Serial ATA Device: MATSHITADVD-R UJ-898
USB device: USB 2.0 Bus
USB device: Hub
USB device: USB receiver
USB Device: Card reader
USB device: Apple keyboard / Trackpad
USB device: Hub BRCM2070
USB Device: USB Bluetooth host controller
USB device: USB 2.0 Bus
USB device: Hub
USB Device: IR receiver
USB device: ISight built-in
Crush Bus:
You have the MacBookPro6, 2 - the Edsel of Mac. There may be the failure of logic-board that was covered by a recall program that is now complete.
The model was abandoned in February 2011. From five years from this date, it will be classified by Apple as "vintage product." This means that Apple will refuse probably a maintenance action (see exceptions on the linked page.) In this case, you will need to go to an independent service provider. The part can be is no longer available, or the repair may not be profitable.
An appointment of 'Genius' in an Apple Store, or go to a different service provider authorized, to have the tested machine. Diagnoses of current equipment used by service providers don't detect the fault. There is a specific test for the same problem that Apple calls "VST" (for "video switching Test.") Ask for it. A "Failed" result means that the defect is present.
You may be quoted a price of about $350 (in the United States) for a "repair," which is to send the unit to a repair shop central and lasts about two weeks. For this package, found nothing wrong with it should be fixed, not only the logic board.
Sometimes, the spare part is also faulty, so be prepared for this eventuality. If you decide to pay for a new logic board, rigorously test during the 90 day warranty on the repair. Some owners have reported that they went up to three replacement boards before you get one that worked.
If you don't want to pay for the repair, you may (or may not) be able to work around the problem by disabling automatic switching graphics. To use the separate graphics processor, you will need a third-party utility to manually switch to him.
Often, the problems start after an upgrade of the OS. If the upgrade has been recently, and you have backups, you can then go back to a previous version of OS X.
Maybe you are looking for
-
Joe sends an email to me and one dozen others. As each response, Joe, every answer that comes to me is attached to the e-mail of origin rather than as previously, simply, I would like to get a copy of each answer with no link. Often stakeholders incl
-
Any way to change the line of demarcation axis weight?
I can set the BaselineStrokeThickness and BaselineStroke axis, but is there a way to do the same for the demarcations? Thank you!
-
Differential polarization resistance
My USE puts a tip of 15 v... about 1 msec in duration that I need to measure differentially. I think that my sw measure is correctly set. If the circuit resembles the attachment don't I still have to add the polarization resistors? The 12 ohms is
-
No option to trun off clicking on to increase/decrease volume on MediaSmart Panel?
Does anyone know if there is a way to disable the clicking sound when increasing or decreasing the volume on the MediaSmart Panel? If so, how? I couldn't find an option for her. Thanks in advance.
-
Dual Boot Vista and XP in separate hard drives?
I currently installed on a hard drive in Vista and I have an extra which is 160 GB I want to install XP on so that I can dualboot both, is it possible? Remember that there is no partition in question here.