Dynamic Crypto map & Defaultl2lGroup

Dear all,

How Defaultl2lGroups & dynamic crypto of the cards can be configured in an asa.

Why I need?

All our stores because asa 5505 (with dynamic ip addresses) are connected to the network head asa 5550 via dynamic vpn and headboard has 2 ISPS.

In fact, we have two lease lines a primary and another backup. Surprisingly, we have only a single subnet on the inside. Now that the main link BW is fully occupied. I want to use the help link too. I wonder if I can have several dynamic cryptographic cards & several groups default tunnel. While I can define servers in one vlan and users in other VLANs. and with two dynamic crypto & default tunnel grps I think passing a subnet (part of the 1st dynamic default crypto & 1 tunelgrp) and second subnet on the other link (2nd dynamic crypo & 2nd tunel default grp). This way the user vpn and internet traffic wil go through 1 link and vpn servers and internet traffic will pass through second link as both the subnet vpn will have another link as backup to each other.

Please provide us with the possibilities.

Please share your ideas.

Help, please.

Thanks in advance,

Kind regards

Jean Michel

Hi Sr,

1 default policy

Up to 65535 crypto map entries (including static and dynamic)

Be sure to note all the useful messages.

For this community, which is as important as a thank you.

Tags: Cisco Security

Similar Questions

ASA dynamic Crypto map

I was looking at this example and did not have a clear explanation about the use of the
```
tunnel-group DefaultL2LGroup
```
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080b3d511.shtml

Why is the pre-shared-key * different pre-shared key talks about cisco123 ? What is a wild card to accept any

identification key by spoke them? Can it be set or is set as it is? I don't see the advantage if it's 'accept all '.

Thank you

Pete

Pete,

"*" is how ASA will display a key, it is hidden when you list the running configuration.
```
bsns-asa5505-19#  conf t
bsns-asa5505-19(config)# tunnel-group BERN ipsec-attributes
bsns-asa5505-19(config-tunnel-ipsec)# ikev1 pre-shared-key 1234556778
bsns-asa5505-19(config-tunnel-ipsec)# sh run tunnel-group BERN ipsec-attri
tunnel-group BERN type remote-access
tunnel-group BERN ipsec-attributes
ikev1 pre-shared-key *****
```
There is no 'accept all' in IKE given that this key will be used to protect and decode identities of IKE.

Also, take a look in the tunnel-group mapping.

At a glance by default, tunnel groups are used as a last ditch effort in the match. That is, they will receive most of the peers with IPs dynamic (or unspecified).

M.

Dynamic crypto several cards on the interface

I have an ASA 5540 executes code 8.2. The firewall has tunnels, VPNS, IPSec standard on this remote access VPN and SSL VPN without client.

I have 1921 Cisco routers with 4 G wireless cards must open dynamic VPN with the ASA 5540, so it seems that I need to implement a solution of EzVPN here.

My question is, multiple dynamic crypto maps are supported on a single interface?

For example, the current configuration of lists

PFS set 20 crypto dynamic-map outside_dyn_map Group 1

Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

outside_map interface card crypto outside

In addition to cryptographic cards for static L2L tunnels.

I guess when I add the EzVPN I have to create a new dynamic map. After having done that, simply add something like that?

card crypto outside_map 65534 ipsec isakmp dynamic outside_new_map

Basically a different sequence number and card name?

Hi Colin,

It is fundamentally correct, that you will encounter some problems on incoming connections, two on the external interface dynamic crypto map entries.

One possibility would be to include a return address for correspondence for you EZ - VPN, for example, generously describe the Remote LAN as the destination of the encryption access list.

For example if your remote LAN is all within the range 10.66.0.0/16 set up an access as list:

outside_new [local area network] ip access list allow [local mask] 10.66.0.0 255.255.0.0

and include it in you card crypto dynamic outside_new_map

PFS set 20 crypto dynamic-map outside_new_map Group 1

Crypto-map dynamic outside_new_map 20 the value transform-set ESP-3DES-SHA

crypto dynamic-map outside_new_map 20 the value corresponds to the address outside_new

See also:

http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/IKE.html#wp1042880

IOS mixed Crypto Maps with Checkpoint Firewall

I have a config encryption that works very well with a remote CheckPoint Firewall:

-------------- \/ CONFIG 1 \/--------------------

crypto ISAKMP policy 5

BA 3des

md5 hash

preshared authentication

!

ISAKMP crypto key address 1.2.3.4 cryptokey1

!

Crypto ipsec transform-set esp-3des esp-md5-hmac txfrmset1

!

crypto dynamic-map vpn Dynamics 10

Set transform-set txfrmset1

!

secure1_in card crypto ipsec isakmp 1

defined by peer 205.245.184.2

Set transform-set txfrmset1

match address 105

!

IP nat inside source overload map route sheep interface Ethernet0

!

sheep allowed 10 route map

corresponds to the IP 110

!

access-list 105 permit ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255

------------/\ CONFIG 1 /\ --------------------

I need to add a card for remote clients using the Cisco VPN 3.6 client.

I have a card encryption that has worked great for me in the past. The combination

Both looks like this:

---------------\/ CONFIG 2 \/ --------------------------

Nine AAA

AAA authentication login userauthen local

AAA authorization groupauthor LAN

crypto ISAKMP policy 5

BA 3des

md5 hash

preshared authentication

!

crypto ISAKMP policy 10

BA 3des

md5 hash

preshared authentication

Group 2

!

cryptokey1 key crypto isakmp address 1.2.3.4 No.-xauth

!

Crypto ipsec transform-set esp-3des esp-md5-hmac txfrmset1

!

crypto dynamic-map vpn Dynamics 10

Set transform-set txfrmset1

ISAKMP crypto client configuration group remote1

cryptokey2 key

DNS 10.0.0.4

WINS 10.0.0.5

VPN-pool

!

card crypto client secure1_in of authentication list userathen

card crypto isakmp authorization list groupauthor secure1_in

client configuration address card crypto secure1_in answer

secure1_in map ipsec-isakmp crypto 5

defined peer 1.2.3.4

Set transform-set txfrmset1

match address 105

vpnclient 10-isakmp ipsec vpn dynamic-dynamic crypto map

!

IP VPN-pool pool 172.16.30.1 room 172.16.30.254

IP nat inside source overload map route sheep interface Ethernet0

access-list 105 permit ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255

!

access-list 110 deny ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255

access-list 110 permit ip 192.168.0.0 0.0.0.255 any

!

sheep allowed 10 route map

corresponds to the IP 110

---------------/\ CONFIG 2 /\---------------------------

It's classic crypto right out of the playbook of Cisco. This card works

very well with the Cisco VPN client, but produced the following errors after a

successful with Checkpoint Firewall P1 installation:

--------------\/ ERROR OUTPUT \/ -----------------------

05:13:02: ISAKMP (0:2): send package to 1.2.3.4 (R) MM_KEY_EXCH

05:13:02: ISAKMP (0:2): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE

Former State = new State IKE_R_MM5 = IKE_P1_COMPLETE

05:13:02: ISAKMP (0:2): need to config/address

05:13:02: ISAKMP (0:2): need to config/address

05:13:02: ISAKMP: node set 1502565681 to CONF_ADDR

05:13:02: ISAKMP (0:2): pool of IP addresses not defined for ISAKMP.

05:13:02: ISAKMP (0:2): node 1502565681 error suppression FALSE reason «»

05:13:02: ISAKMP (0:2): entry = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE

Former State = new State IKE_P1_COMPLETE = IKE_CONFIG_MODE_SET_SENT

05:13:02: ISAKMP (0:2): 1.2.3.4 received packet (R) CONF_ADDR

05:13:02: ISAKMP: node set-1848822857 to CONF_ADDR

05:13:02: ISAKMP (0:2): entry unknown: status = IKE_CONFIG_MODE_SET_SENT, major, minor = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE

05:13:04: ISAKMP (0:2): 1.2.3.4 received packet (R) CONF_ADDR

--------------/\ ERROR OUTPUT /\--------------------------

This does not happen to config 1. If it's a PIX, I would use the

No.-config-mode keyword after the No.-xauth on isakmp crypto "key."

command line. It is not available on IOS IPSEC and I have never

needed to do before. I am running Cisco IOS 12.2 (5.4) T on a VPN of 1721

router. The static map seems to work by itself. What I am doing wrong?

I saw her a couple of times and to be honest have never taken down to an exact cause, although in this case it looks like almost to the point of control request an IP address which is weird. Try the following:

1. Add "card crypto secure1_in client configuration address to initiate" and see what it does.

2. try 12.2 (8) code T5 with it, I had a previous user running 12.2 (11) T and we got the same error messages, returning to this level of code it is resolved.

In addition, you wouldn't need:

> access-list 110 deny ip 192.168.10.0 0.0.0.255 172.16.30.0 0.0.0.255

for example, so that you do not NAT client VPN traffic?

Priority crypto map

Hi all

I try to have several VPN site-to-site hooked to my Interface Outside one.

I understand that I may have a crpypto card assigned to the interface.

If I want to for example, one of virtual private networks to require PFS but either not to do it-just set a different priority under the Crypto map? Map crypro entries get transformed top to bottom until a match is found?

for example

CMAP 10 ipsec-isakmp crypto card
defined peer x.x.x.x
game of transformation-TSET
match address ACL1

Crypto map CMAP 20 ipsec-isakmp
defined peer y.y.y.y
game of transformation-TSET
match address ACL2
set the pfs Group 2

Thank you

You're right, the encryption card is dealt top-down. So if your traffic is ACL2 (and not ACL1!), then all settings configured under sequence CMAP 20 are relevant in this regard.

role of the crypto map sequence number

I'm setting up IPSEC in four sites in a manner completely mesh. The problem I have is one of the sites is our main hub and everything works on a class B network. Creating ACL to get from one place to another is relatively simple, but getting a site on the main hub is another story, because other sites are all the subnets in the class B address, I have to remove these subnets of a class B and at the same time to encrypt the rest of the class B address. Subnets of the smaller sites are for most of the 24 and 25. I was wondering if the sequence # in the card order crypto could play a role for me. If I set the priority on small sites and put the lower on the map pointing to the main pole encryption could I get away with something like this:

licence (local subnet) 0.0.0.255 x.x.x.x where x.x.x.x (category B) 0.0.255.255

Thanks in advance for taking the time.

Mario

Mario... that's exactly how it works for the two ISAKMP Crypto map policies and policy. It will look at the lowest number (like attentive) so if you do your remote sites all a higher priority (lower number), then you should be fine with respect to the central site.

Kind regards

2 crypto maps to the external interface? Possible?

Hi, I have a little problem with a PIX 515 UR on FOS 6.3 (1).

What I'm trying to do is to run 2 VPN site to site to him. The thing is: although I can get two separate crypt cards into the config, its only the more recent which is active when I do a ' sh crypto his '.

Anyone have any ideas?

TIA-

Gary

I do multiple like this:

I have the main Board, applied externally:

toXXXX interface card crypto outside

Then, I build maps more screaming like ACL if:

toXXXX 20 ipsec-isakmp crypto map

card crypto toXXXX 20 match address no_nat (name of the ACL)

card crypto toXXXX 20 peers set x.x.x.x

toXXXX 20 transform-set mytrans crypto card

life safety association set card crypto toXXXX 20 seconds 3600 4608000 kilobytes

toXXXX 40 ipsec-isakmp crypto map

card crypto toXXXX 40 correspondence address toACME (name of the ACL)

card crypto toXXXX 40 peers set x.x.x.x

toXXXX 40 transform-set mytrans crypto card

life safety association set card crypto toXXXX 40 seconds 3600 4608000 kilobytes

supported vs IPSec VRF taking crypto maps for several tunnels

Hi all!

I came to know that we can use the same public ip address for the creation of several tunnels to different websites using crypto-cards featuring many lines each representing a reference to a particular tunnel and using vrf aware IPsec, but I would like to know what are the differences / advantages / cautions.

Thanks for your time

Murali.

Murali

That I understand the feature essentially allows you to have multiple IPSEC tunnels and traffic in the tunnel that is to say. source and destination IP of the high-end devices can be in different VRF.

So it works mainly with the MPLS VPN IE. If you had several MPLS VPN each with their own VRF you can then run ISPEC tunnels on the MPLS network and when packets are received, they are automatically in the correct VRF.

You could not do that normal crypto cards IE. You can cancel again several IPSEC tunnels on a public IP address but then everything would be traffic in the same global routing table.

If the benefit is basically the same that you get with any VRF installation IE. logical separation of traffic on a single device.

Can't really say much about the warnings as I've never used it but there are some restrictions.

See this link for more details-

http://www.Cisco.com/c/en/us/TD/docs/iOS-XML/iOS/sec_conn_ikevpn/configuration/XE-3s/asr1000/sec-IKE-for-IPSec-VPNs-XE-3s-asr1000-book/sec-VRF-aware-IPSec.html

Jon

Encryption: "Apply crypto map interface.

East - the best forum to discuss encryption?

I want to implement a single aes encryption between an ISDN Bri1/0 port on a 2611xm and a 2811.

I want to encrypt everything except telnet on the ISDN link between these routers. I want to telent between routers just in case the encryption locks himself. This is my requirement of customers.

Question #1: Should I contact the card encryption the Ethernet port (as I have seen in many examples) or on the ISDN connection?

Question #2: If I ask the encryption card to the ISDN connection, should I do the encryption the BRI port card or the dialer?

Question #3: Assuming that both routers and all segments use the 10.0.0.0 network and are not connected to what anyone else, the following access list would work?

access list 110

deny ip any eq telnet

allow an ip

Thank you

Mark

Hi Mark,

Apply the card encryption to your outgoing interface (Dialer)

You probably will lock the router by putting

an ip address allowed any one in your crypto access list

you have probably even to add telnet deny entry in your access list if you are ready to open your session to the router

I suggest you

extended to remote IP access list

deny ip any eq telnet

ip licensing 10.0.1.0 0.0.0.255 10.0.2.0 0.0.0.255

The remote site would have a mirror

social-seat extended IP access list

deny ip any eq telnet

IP 10.0.2.0 allow 0.0.0.255 10.0.1.0 0.0.0.255

MBP mid-2010 (15-inch, 2.53 GHz, i5) unexpected reboot of the system of dynamic switching map chart

Hi there, I've never had this problem when I bought my MBP in 2010, but after the problem with unexpected reboots of El Capitan passage has become more common and is really affecting the productivity of my laptop.

For clarity, here's my cell phone information:

MacBook Pro (15-inch, mid 2010)

Processor: Intel Core i5 2.53 GHz to

Memory: 8 GB 1067 MHz DDR3

Graphics card:

integrated - Intel HD Graphics 288 MB

discreet - NVIDIA GeForce GT 330 M 256 MB

I ran the the Apple Hardware Test with no problems found. After looking on the forums and identifying the problem I installed gfxCardStatus to keep the graphics card using only internally, however, some programs force the use of Nvidia, which translates as the unexpected restarts.

The latest report of panic is attached below:

In any case, it is quite upsetting that after spending thousands of dollars on apple and laptops high-end, these problems are properly does not recognize their existence. After discussing with them several times they fail to take responsibility, when it is clearly a case of defective material...

Any suggestions for managing at least this issue would be very useful.

Thank you

Philippe

Sam 5 17:01:31 dec 2015

Panic report *.

panic (cpu 1 0xffffff7f8ddf1bad appellant): "panic GPU: 7f [] 3 3 0 0 0 0 3: NVRM [0 / 1:0:0]: error 0 x 00000100 reading: CFG 0xffffffff, 0xffffffff, 0xffffffff, BAR0 0xd2000000 0xffffff91277cf000 sControl-3.11.33.1/src/AppleMuxControl/kext/GPUPanic.cpp:127 P2/4\n"@/Library/Caches/com.apple.xbs/Sources/AppleGraphicsControl/AppleGraphic 0x0a5480a2, D0,

Backtrace (CPU 1), frame: return address

0xffffff811461b0a0: 0xffffff800ace5307

0xffffff811461b120: 0xffffff7f8ddf1bad

0xffffff811461b200: 0xffffff7f8b97ffa4

0xffffff811461b2c0: 0xffffff7f8ba4cadd

0xffffff811461b300: 0xffffff7f8ba4cb48

0xffffff811461b380: 0xffffff7f8bcd1a23

0xffffff811461b4f0: 0xffffff7f8ba70b79

0xffffff811461b510: 0xffffff7f8b986cfd

0xffffff811461b5c0: 0xffffff7f8b984690

0xffffff811461b7c0: 0xffffff7f8b98576f

0xffffff811461b8a0: 0xffffff7f8d2810ea

0xffffff811461b8e0: 0xffffff7f8d290aa3

0xffffff811461b900: 0xffffff7f8d2bf3ea

0xffffff811461b940: 0xffffff7f8d2bf449

0xffffff811461b980: 0xffffff7f8d296642

0xffffff811461b9d0: 0xffffff7f8d2620ae

0xffffff811461ba70: 0xffffff7f8d25df51

0xffffff811461baa0: 0xffffff7f8d25bae5

0xffffff811461bae0: 0xffffff800b2e2057

0xffffff811461bb80: 0xffffff800b2e4828

0xffffff811461bbe0: 0xffffff800b2e1967

0xffffff811461bd20: 0xffffff800ada07d0

0xffffff811461be30: 0xffffff800ace9aa3

0xffffff811461be60: 0xffffff800accd478

0xffffff811461bea0: 0xffffff800acdcfd5

0xffffff811461bf10: 0xffffff800adc13aa

0xffffff811461bfb0: 0xffffff800adf4b36

Extensions of core in backtrace:

com.apple.driver.AppleMuxControl (3.11.33b1) [FF6CE9C5-9D8F - a 3, 48 - 9 d 10-2BB9C2DDD22 7]@0xffffff7f8dde3000-> 0xffffff7f8ddf6fff

dependency: com.apple.driver.AppleGraphicsControl (3.11.33b1) [4ADB751E-5208-3DA7-A8C3-E9EC07 263B16]@0xffffff7f8dddb000

dependency: com.apple.iokit.IOACPIFamily (1.4) [CBAE26D8-0ACB-3C1F-8347-FDCA67EC40B3] @0xfffff f7f8b7b4000

dependency: com.apple.iokit.IOPCIFamily (2.9) [8E5F549E-0055-3C0E-93F8-E872A048E31B] @ 7f8b52d000 0xffffff

dependency: com.apple.iokit.IOGraphicsFamily (2.4.1) [48AC8EA9-BD3C-3FDC-908D-09850215AA32] @0 xffffff7f8b8d2000

dependency: com.apple.driver.AppleBacklightExpert (1.1.0) [5CB7D4B7-B100-34EE-BD40-1EC07E865C 67]@0xffffff7f8ddde000

com.apple.nvidia.classic.NVDAResmanTesla (10.0) [05FC5D7E-BB0B-3232-BBBD-8A49B687 0D8B]@0xffffff7f8b929000-> 0xffffff7f8bb9efff

dependency: com.apple.iokit.IOPCIFamily (2.9) [8E5F549E-0055-3C0E-93F8-E872A048E31B] @ 7f8b52d000 0xffffff

dependency: ffff7f8b919000 @0xff com.apple.iokit.IONDRVSupport (2.4.1) [814A7F4B-03EF-384A-B205-9840F0594421]

dependency: com.apple.iokit.IOGraphicsFamily (2.4.1) [48AC8EA9-BD3C-3FDC-908D-09850215AA32] @0 xffffff7f8b8d2000

com.apple.nvidia.classic.NVDANV50HalTesla (10.0) [CA 56199, 6 - 3C8D - 3EBB - B5EF - 7B1B467 8ACF9]@0xffffff7f8bba9000-> 0xffffff7f8be56fff

dependency: com.apple.nvidia.classic.NVDAResmanTesla (10.0.0) [05FC5D7E-BB0B-3232-BBBD-8A49B6 870D8B]@0xffffff7f8b929000

dependency: com.apple.iokit.IOPCIFamily (2.9) [8E5F549E-0055-3C0E-93F8-E872A048E31B] @ 7f8b52d000 0xffffff

com.apple.GeForceTesla (10.0) [49982DF3-8146-3BD0-AD3F-A7E7AB5ACBB5] @0xffffff7f8d 240000-> 0xffffff7f8d30bfff

dependency: com.apple.iokit.IOPCIFamily (2.9) [8E5F549E-0055-3C0E-93F8-E872A048E31B] @ 7f8b52d000 0xffffff

dependency: ffff7f8b919000 @0xff com.apple.iokit.IONDRVSupport (2.4.1) [814A7F4B-03EF-384A-B205-9840F0594421]

dependency: com.apple.iokit.IOGraphicsFamily (2.4.1) [48AC8EA9-BD3C-3FDC-908D-09850215AA32] @0 xffffff7f8b8d2000

dependency: com.apple.nvidia.classic.NVDAResmanTesla (10.0.0) [05FC5D7E-BB0B-3232-BBBD-8A49B6 870D8B]@0xffffff7f8b929000

Corresponding to the current thread BSD process name: WindowServer

Mac OS version:

15B 42

Kernel version:

Darwin Kernel Version 15.0.0: Sat Sep 19 15:53:46 PDT 2015; root:XNU-3247.10.11~1/RELEASE_X86_64

Kernel UUID: AB5FC1B4-12E7-311E-8E6F-9023985D8C1D

Slide kernel: 0x000000000aa00000

Text of core base: 0xffffff800ac00000

Text __HIB base: 0xffffff800ab00000

Name of system model: MacBookPro6, 2 (Mac-F22586C8)

Availability of the system in nanoseconds: 1557747038609

last load kext to 69928374174: com.apple.driver.AudioAUUC 1.70 (addr 0xffffff7f8d537000 size 32768)

Finally unloaded kext to 240741317817: com.apple.driver.usb.AppleUSBUHCI 1.0.1 (addr 0xffffff7f8c248000 size 126976)

kexts responsible:

com.radiosilenceapp.nke.Filter 1.1

com.apple.driver.AudioAUUC 1.70

com.apple.driver.AppleHWSensor 1.9.5d0

com.apple.driver.AGPM 110.20.21

com Apple.filesystems.autofs 3.0

com.apple.driver.AppleOSXWatchdog 1

com.apple.driver.AppleMikeyHIDDriver 124

com.apple.driver.AppleMikeyDriver 272.50.31

com Apple.Driver.pmtelemetry 1

com.apple.iokit.IOUserEthernet 1.0.1

com.apple.driver.AppleUpstreamUserClient 3.6.1

com.apple.iokit.IOBluetoothSerialManager 4.4.2f1

com.apple.GeForceTesla 10.0.0

com.apple.driver.AppleHDA 272.50.31

com.apple.driver.AppleIntelHDGraphics 10.0.0

com.apple.Dont_Steal_Mac_OS_X 7.0.0

com.apple.driver.AppleHV 1

com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.4.2f1

com.apple.driver.AppleSMCPDRC 1.0.0

com.apple.driver.AppleMuxControl 3.11.33b1

com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0

com.apple.driver.AppleIntelSlowAdaptiveClocking 4.0.0

com.apple.driver.AppleMCCSControl 1.2.13

com.apple.driver.AppleIntelHDGraphicsFB 10.0.0

com.apple.driver.AppleSMCLMU 208

com.apple.driver.AppleLPC 3.1

com.apple.driver.SMCMotionSensor 3.0.4d1

com.apple.driver.AppleUSBTCButtons 245,4

com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1

com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0

com.apple.BootCache 37

com.apple.driver.AppleUSBTCKeyboard 245,4

com.apple.driver.AppleUSBCardReader 3.7.1

com.apple.driver.AppleIRController 327,5

com.apple.iokit.SCSITaskUserClient 3.7.7

com.apple.iokit.IOAHCIBlockStorage 2.8.0

com.apple.driver.AirPort.Brcm4331 800.20.24

com.apple.driver.AppleFWOHCI 5.5.2

3.1.5 com.apple.driver.AppleAHCIPort

com.apple.iokit.AppleBCM5701Ethernet 10.1.11

com.apple.driver.usb.AppleUSBEHCIPCI 1.0.1

com.apple.driver.AppleSmartBatteryManager 161.0.0

com.apple.driver.AppleRTC 2.0

com.apple.driver.AppleACPIButtons 4.0

com.apple.driver.AppleHPET 1.8

com.apple.driver.AppleSMBIOS 2.1

com.apple.driver.AppleACPIEC 4.0

com.apple.driver.AppleAPIC 1.7

com.apple.driver.AppleIntelCPUPowerManagementClient 218.0.0

com Apple.NKE.applicationfirewall 163

com Apple.Security.Quarantine 3

com.apple.security.TMSafetyNet 8

com.apple.driver.AppleIntelCPUPowerManagement 218.0.0

com.apple.AppleGraphicsDeviceControl 3.11.33b1

com Apple.kext.Triggers 1.0

com.apple.iokit.IOSurface 108.0.1

com.apple.iokit.IOSerialFamily 11

com.apple.nvidia.classic.NVDANV50HalTesla 10.0.0

com.apple.nvidia.classic.NVDAResmanTesla 10.0.0

com.apple.driver.DspFuncLib 272.50.31

com.apple.kext.OSvKernDSPLib 525

com.apple.driver.CoreCaptureResponder 1

com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.4.2f1

com.apple.iokit.IOBluetoothFamily 4.4.2f1

com.apple.driver.AppleSMBusPCI 1.0.14d1

com.apple.driver.AppleBacklightExpert 1.1.0

com.apple.iokit.IONDRVSupport 2.4.1

com.apple.driver.AppleGraphicsControl 3.11.33b1

com.apple.driver.IOPlatformPluginLegacy 1.0.0

com.apple.iokit.IOSlowAdaptiveClockingFamily 1.0.0

com.apple.driver.AppleSMBusController 1.0.14d1

com.apple.iokit.IOFireWireIP 2.2.6

com.apple.driver.AppleHDAController 272.50.31

com.apple.iokit.IOGraphicsFamily 2.4.1

com.apple.iokit.IOHDAFamily 272.50.31

com.apple.iokit.IOAudioFamily 204,1

com.apple.vecLib.kext 1.2.0

com.apple.driver.IOPlatformPluginFamily 6.0.0d7

com.apple.driver.AppleSMC 3.1.9

com.apple.driver.CoreStorage 517

com.apple.driver.usb.IOUSBHostHIDDevice 1.0.1

com.apple.driver.AppleUSBMultitouch 250.4

com.apple.iokit.IOSCSIBlockCommandsDevice 3.7.7

com.apple.iokit.IOUSBMassStorageDriver 1.0.0

com.apple.iokit.IOUSBHIDDriver 900.4.1

com.apple.driver.usb.AppleUSBHostCompositeDevice 1.0.1

com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.7.7

com.apple.iokit.IOBDStorageFamily 1.8

com.apple.iokit.IODVDStorageFamily 1.8

com.apple.iokit.IOCDStorageFamily 1.8

com.apple.driver.usb.AppleUSBHub 1.0.1

com.apple.iokit.IOAHCISerialATAPI 2.6.2

com.apple.iokit.IOSCSIArchitectureModelFamily 3.7.7

1101.24 com.apple.iokit.IO80211Family

com Apple.Driver.corecapture 1.0.4

4.5.8 com.apple.iokit.IOFireWireFamily

com.apple.iokit.IOAHCIFamily 2.8.0

com.apple.iokit.IOEthernetAVBController 1.0.3b3

com.apple.driver.mDNSOffloadUserClient 1.0.1b8

com.apple.iokit.IONetworkingFamily 3.2

com.apple.iokit.IOUSBFamily 900.4.1

com.apple.driver.usb.AppleUSBEHCI 1.0.1

com.apple.iokit.IOUSBHostFamily 1.0.1

com.apple.driver.AppleUSBHostMergeProperties 1.0.1

com.apple.driver.AppleEFINVRAM 2.0

com.apple.driver.AppleEFIRuntime 2.0

com.apple.iokit.IOHIDFamily 2.0.0

com.apple.iokit.IOSMBusFamily 1.1

com Apple.Security.sandbox 300.0

com.apple.kext.AppleMatch 1.0.0d1

com.apple.driver.AppleKeyStore 2

com.apple.driver.AppleMobileFileIntegrity 1.0.5

com.apple.driver.AppleCredentialManager 1.0

com.apple.driver.DiskImages 415

com.apple.iokit.IOStorageFamily 2.1

com.apple.iokit.IOReportFamily 31

com.apple.driver.AppleFDEKeyStore 28.30

com.apple.driver.AppleACPIPlatform 4.0

com.apple.iokit.IOPCIFamily 2.9

com.apple.iokit.IOACPIFamily 1.4

com.apple.kec.Libm 1

com Apple.KEC.pthread 1

com Apple.KEC.corecrypto 1.0

Model: MacBookPro6, 2, MBP61.0057.B11 of BootROM, 2 processors, Intel Core i5 2.53 GHz, 8 GB, MSC 1.58f17

Graphics: integrated graphics card Intel HD, Intel HD Graphics,

Graphics card: NVIDIA GeForce GT 330 M, NVIDIA GeForce GT 330 M, PCIe, 256 MB

Memory module: DIMM0/0 BANK, 4 GB DDR3, 1067 MHz, 0x029E, 0x434D5341344758334D314131303636433720

Memory module: DIMM0/1 BANK, 4 GB DDR3, 1067 MHz, 0x029E, 0x434D5341344758334D314131303636433720

Airport: spairport_wireless_card_type_airport_extreme (0x14E4, 0 x 93), Broadcom BCM43xx 1.0 (5.106.98.100.24)

Bluetooth: Version 4.4.2f1 16391, 3 services, 27 aircraft, 1 incoming serial ports

Network service: Wi - Fi, AirPort, en1

Serial ATA Device: TOSHIBA MK5055GSXF, 500,11 GB

Serial ATA Device: MATSHITADVD-R UJ-898

USB device: USB 2.0 Bus

USB device: Hub

USB device: USB receiver

USB Device: Card reader

USB device: Apple keyboard / Trackpad

USB device: Hub BRCM2070

USB Device: USB Bluetooth host controller

USB device: USB 2.0 Bus

USB device: Hub

USB Device: IR receiver

USB device: ISight built-in

Crush Bus:

You have the MacBookPro6, 2 - the Edsel of Mac. There may be the failure of logic-board that was covered by a recall program that is now complete.

The model was abandoned in February 2011. From five years from this date, it will be classified by Apple as "vintage product." This means that Apple will refuse probably a maintenance action (see exceptions on the linked page.) In this case, you will need to go to an independent service provider. The part can be is no longer available, or the repair may not be profitable.

An appointment of 'Genius' in an Apple Store, or go to a different service provider authorized, to have the tested machine. Diagnoses of current equipment used by service providers don't detect the fault. There is a specific test for the same problem that Apple calls "VST" (for "video switching Test.") Ask for it. A "Failed" result means that the defect is present.

You may be quoted a price of about $350 (in the United States) for a "repair," which is to send the unit to a repair shop central and lasts about two weeks. For this package, found nothing wrong with it should be fixed, not only the logic board.

Sometimes, the spare part is also faulty, so be prepared for this eventuality. If you decide to pay for a new logic board, rigorously test during the 90 day warranty on the repair. Some owners have reported that they went up to three replacement boards before you get one that worked.

If you don't want to pay for the repair, you may (or may not) be able to work around the problem by disabling automatic switching graphics. To use the separate graphics processor, you will need a third-party utility to manually switch to him.

Often, the problems start after an upgrade of the OS. If the upgrade has been recently, and you have backups, you can then go back to a previous version of OS X.

Several entries of the dynamic map (policies of the phase 2) on SAA

Hi all

I have a setup where I set up VPN remotely on my ASA. I came to a situation where I wanted to allow the two IPSEC client using cisco VPN client and android phone using L2TP/IPSEC

What is happening is that I want to use PFS for IPSEC clients, but my android phone does not support this. Then I tried to create two sequences in my dynamic crypto map, but the first sequence is always put in correspondence and therefore ike phase2 fails. If I put the sequence without PFS first, he will be first, and my client IPSEC uses both PFS...

If I remove the PFS, fine.

So is there a way either the AoA match to multiples of phase 2 policy, I mean not only several transform set in the same order, but also for pfs in my case.

My L2TP client using authentication rsa - sig and are dynamically mapped to a tunnel-group, so I thought maybe we can specify map entries different crypto depending on the authentication method, but it seems that the only option that we linked to this is for card crypto inherited, where we can choose the trustpoint for outbound connections.

So if anyone has an idea, I would be interested, otherwise, I guess I can leave without PFS...

Unfortunately not with PFS, as part of the overall transformation (for example: ESP-3DES, etc) then you can set several transformation under 1 dynamic map. However, not for PFS that you only have 1 option either turn or off as PFS is optional.

VPN ASA ASA with dynamic IP of the branch

Hello

I would like to connect a private network Virtual Office HQ to a branch using two ASAs.

I have a 5520 in the HQ and 5505 in the branch.

My problem is in the office where I have a dynamic IP (ADSL).

I couldn't find an example of this type of configuration.

Can you help me?

Kind regards

Sergio Santos

Hi Sergio,

Well, you have two options:
- Dynamic to static L2L tunnel:
On the 5520, you must configure a dynamic encryption card because you don't know the IP address the 5505 will have and even if you IP address may vary. So:

Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

Crypto-map dynamic dynmap 1 transform-set RIGHT
Crypto-map dynamic dynmap 1 the value reverse-road
map mymap 10-isakmp IPSec crypto dynamic mymap
mymap outside crypto map interface

If you already have other tunnels already configured them just change the name of the crypto map that I used above with one you already have, in the example I used a sequence of 10 number because I have more tunnels in place but you need without ensuring that the card encryption where you attach the dynamic crypto map has the highest value! ID recommend using a value of 65535, which is the highest, you can use, this will allow you to configure static tunnels in the future without having need to reconfigure one you linked to the dynamics.

Besides that you must configure the tunnel-group... but as you know for tunnels L2L with PSK in MainMode tunnel-group name MUST be the IP address peer, and in this case, we do not know, do not worry, we can configure the PSK under the DefaultL2LGroup

IPSec-attributes tunnel-group DefaultL2LGroup
pre-shared-key *.

That's all you need on the 5520, in addition to the basic configuration PH1 for the construction of a tunnel.

On 5505 all you need to do is to set up a regular tunnel because from the point of view 5505, we know the IP address of the 5520 and it will not change:

map MYMAP 1 IPSec-isakmp crypto
defined peer X.X.X.X
Set transform-set RIGHT
match address MYCRYPTOACL

Group of tunnel X.X.X.X IPSec-attributes
pre-shared-key *.
- The other option will be to configure EzVPN you use a 5505
http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808a61f4.shtml

http://www.Cisco.com/en/us/docs/security/ASA/asa72/configuration/guide/ezvpn505.html

HTH!

Problem of static-dynamic ASA5505 L2L

The two ASA5505 using version 9.2.3 tried ikev1 and ikev2, it worked before, but I don't know what the problem is now...

I can read dynamic end tunnel ASA (default behavior), I mean that I have to ping asa (DynASA (config) # ping inside the 172.22.82.5).

When I try to ping resources or access for all clients behind DynamicASA to StaticASA, it appears in the log:

6 June 25, 2015 21:40:50 302020 192.168.11.7 1 172.22.22.21 0 Built of outbound ICMP connection for faddr gaddr laddr 192.168.11.7/1 88.114.6.163/1 172.22.82.21/0

After the tunnel is mounted I can connect clients behind StaticASA to resources behind DynamicASA, but not the other way around (clients behind DynamicASA behind StaticASA, a little two-way remedies does not?)

I tried with DefaultL2L and DYNL2L-policies and both work in a sense...

StaticASA config

interface Vlan1
nameif outside
security-level 0
IP 1.2.3.4 address 255.255.255.0
!
interface Vlan2
nameif inside
security-level 100
IP 172.22.22.1 255.255.255.0
!

network of the ASA2_LAN object
subnet 192.168.11.0 255.255.255.0
network of the ASA1_LAN object
172.22.22.0 subnet 255.255.255.0

access-list tunneli-ASA2 allowed extended ip ASA1_LAN object ASA2_LAN
NAT (inside, outside) static source ASA1_LAN ASA1_LAN ASA2_LAN ASA2_LAN non-proxy-arp-search of route static destination

Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-256-SHA trans1 ikev1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 ipsec-proposal
Crypto than dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 the value reverse-road
DYNL2L-ASA2 4 crypto dynamic-map correspondence address tunneli-ASA2
Crypto dynamic-map DYNL2L-ASA2 4 set transform-set ESP-AES-256-SHA ikev1
Crypto dynamic-map DYNL2L-ASA2 4 set DYNL2L VPN-ipsec-ikev2 proposal
Crypto dynamic-map DYNL2L-ASA2 4 the value reverse-road
card crypto OUTSIDE_MAP 65534-isakmp dynamic ipsec DYNL2L-ASA2
card crypto OUTSIDE_MAP 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
OUTSIDE_MAP interface card crypto outside
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

internal GroupPolicy_ASA2 group strategy
attributes of Group Policy GroupPolicy_ASA2
VPN-tunnel-Protocol ikev1, ikev2

IPSec-attributes tunnel-group DefaultL2LGroup
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.

IPSec-l2l type tunnel-group DYNL2L-ASA2
attributes global-tunnel-group DYNL2L-ASA2
Group Policy - by default-GroupPolicy_ASA2
IPSec-attributes tunnel-group DYNL2L-ASA2
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.

DynamicASA config

interface Vlan1
nameif inside
security-level 100
192.168.11.1 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address dhcp setroute

network of the ASA1_LAN object
172.22.22.0 subnet 255.255.255.0
network of the ASA2_LAN object
subnet 192.168.11.0 255.255.255.0

access-list tunneli-ASA1 allowed extended ip ASA2_LAN object ASA1_LAN

NAT (inside, outside) source Dynamics one interface
NAT (inside, outside) static source ASA2_LAN ASA2_LAN ASA1_LAN ASA1_LAN non-proxy-arp-search of route static destination

card crypto mymap 10 correspondence address tunneli-ASA1
card crypto mymap 10 peer set 1.2.3.4
card crypto mymap 10 set transform-set ESP-AES-256-SHA ikev1
card crypto mymap 10 set ikev2 AES256 AES192 AES OF DYNL2L-VPN-3DES ipsec-proposal
crypto mymap 10 card value reverse-road

internal GroupPolicy_1.2.3.4 group strategy
attributes of Group Policy GroupPolicy_1.2.3.4
VPN-tunnel-Protocol ikev1, ikev2
tunnel-group 1.2.3.4 type ipsec-l2l
tunnel-group 1.2.3.4 General attributes
Group - default policy - GroupPolicy_1.2.3.4
tunnel-group 1.2.3.4 ipsec-attributes
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!

WBR,

Mr.O

Hello

Looks like you have dynamic nat above static nat exempt on-side dynamic IP ASA

NAT (inside, outside) source Dynamics one interface
NAT (inside, outside) static source ASA2_LAN ASA2_LAN ASA1_LAN ASA1_LAN non-proxy-arp-search of route static destination

change the order to move the static nat over the dynamic nat

no nat source (indoor, outdoor) public static ASA2_LAN ASA2_LAN ASA1_LAN ASA1_LAN non-proxy-arp-search of route static destination

NAT (inside, outside) 1 static source ASA2_LAN ASA2_LAN ASA1_LAN ASA1_LAN non-proxy-arp-search of route static destination

HTH

Averroès.

IKEv2 vpn dynamic sites

I do ikev2 VPN with the ASA and sites have a dynamic IP. A solution is to do a vpn site-to site, configure ASA headoffice with dynamic crypto map and the asa of the client with static cryptographic cards and put even the intellectual Headquarters property.

However, a better approach would be the classic scenario of ezvpn but I can't find a reference doc or config for ikev2. Is this supported using ikev2 or the only option, I have one I described above?

Hello

IKEv2 support for VPN tunnels easy on ASAs is not available, only for IKEv1.

It is available on routers Cisco, called FlexVPN:

FlexVPN on Cisco routers:

https://supportforums.Cisco.com/community/NetPro/security/VPN/blog/2012/...

Kind regards

Aditya

Please evaluate the useful messages and mark the correct answers.

invalid-spi-recovery crypto isakmp command worked well in the case of DMVPN

Hello

I did the Setup for Hub/spoke in th DMVPN case and it worked fine. But after reloading Hub and I saw an output of error below, well I added the command invalid-spi-recovery isakmp crypto in the Hub & spokes:

* 7 Oct 03:10:03.175: CRYPTO-4-RECVD_PKT_INV_SPI %: decaps: rec would be package IPSEC a bad spi to destaddr = 150.1.1.1, prot = 50, spi = 0 x 72662541 (1919296833), port = 150.3.1.3

* 7 Oct 03:10:03.175: CRYPTO-4-RECVD_PKT_INV_SPI %: decaps: rec would be package IPSEC a bad spi to destaddr = 150.1.1.1, prot = 50, spi = 0 x 72662541 (1919296833), port = 150.2.1.2

Note: spoke1 IP address: 150.2.1.2/spoke2's IP address:150.3.1.3/Hub's IP address: 150.1.1.1

My temporary solution for the same problem, I need to erase SPI by manually and it worked fine again.

Everyone has the same problem, please let me know

Kind regards

TRAN

Hello

There is a common misconception of what the invalid-spi-recovery crypto isakmp command does. Even without this command IOS already performs a kind of recovery invalid SPI feature by sending a DELETION notify for the SA has received send peer If she already has an IKE SA with this peer. Still once, this happens regardless of whether the order invalid-spi-recovery crypto isakmp is enabled or not.

With the order of isakmp crypto invalid-spi-recovery , he tries to regulate the condition where a router receives the IPSec traffic with invalid SPI and

It doesn't have an IKE SA with this peer. In this case, it will try to put in place a new IKE session with the peer and then send a DELETION notification on the newly created HIS IKE. However, this command does not work in all configurations of crypto. Are the only configurations that this command works cryptographic instantiated, for example, Asit, and peer static maps from static cryptographic cards where the peer is defined explicitly. Here is a summary of commonly used configurations of crypto and know if invalid spi recovery works with this configuration or not:

Crypto config	Not valid-spi-recovery?
Static crypto map	YES
Dynamic crypto map	NO.
P2P GRE with TP	YES
using love TP w / static PNDH mapping	YES
using love TP w / dynamic PNDH mapping	NO.
ASIT	YES
EzVPN client	N/A

For help with your scenario, you can enable DPD (isakmp crypto keepalive) on the shelf to help the recovery tunnel.

Thank you

Wen

Dynamic Crypto map &amp; Defaultl2lGroup

Similar Questions

Maybe you are looking for

Dynamic Crypto map & Defaultl2lGroup