ASA: Recovery using Sub Interface = (unguarded)?

Similar Questions

• ASA 5510 using only the GB interfaces

  I am looking for should I use a 5510 to activate two interfaces for VPN connections broadband from only a few sites. Our 5505 s (I have dozens) can not manage speeds of more than 100 MB and I have now a few FIOS beyond that--150 to 300mpbs.  I want a 5510 basis who needs to manage a few voice / data sites and just use two interfaces. A basic 5510 allow 2 gigabytes or just ports FE interfaces?  I have to be able to use 2 GB interfaces and no one else. I don't know that the 5510 will probably support the same QOS settings that I use on the 5505 s... I just need more speed interface so that I'm not bottlenecking data (I know I could use several 5505 s and extend the charges but is not how I want to do it for other reasons). Thank you

  Hello

  To my knowledge the ASA5510 supports 2 x 1 Gbps interfaces when you the Security license for the SAA. The basic license counts 100Mbps interfaces.

  Take a look at this document for more information on licensing above

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/license/license82.html#wp190732

  Its a document from the 8.2 version but its still even to 9.x on the license requirement more security get the 2 x 1 Gbps interfaces

  The documentation for ASA5500 series promises an 300Mbps for the ASA5510 model flow, but I guess that's a value of location. In the most recent document, two values of max flow max and Multiprotocol are given.

  Here's a link to the document

  http://www.Cisco.com/en/us/prod/collateral/vpndevc/ps6032/ps6094/ps6120/prod_brochure0900aecd80285492.PDF

  -Jouni

• Cannot ping sub interface from my remote site VPN gateways

  I can't ping my gateways to interface my remote vpn connection sub

  I can ping 192.6.1.0 network, but can't ping network 192.6.2.0 or 192.6.3.0

  When I remote desktop in 192.6.1.20 I can ping all the networks, including gateways to interface sub.

  I think that something in my asa is misconfigured or not added

  ASA NAT rules:

  Exempt NAT Interface: inside

  Source 192.6.0.0/16

  Destination 192.6.10.96/27

  Static NAT interface: inside (it's for the local NAT of E0/0 out)

  Source 192.6.1.1/16

  Interface translated outside the Destination: 172.35.221.200

  Dynamic NAT interface: inside

  Source: no

  Destination: outside

  ASA access rules:

  Permit outside

  Source: no

  Destination: out

  Services: udp, tcp, tcp/http

  Static routes:

  Interface: Outside > network: all outdoors DSL (shows no DSL in the graph)

  

  Some incorrect configuration:

  On the ASA:

  (1) directions are incorrect, the default should point to the next hop route, that is to say: the internet router: 172.35.221.x, as follows:

  Route outside 0.0.0.0 0.0.0.0 172.35.221.x

  ---> where x must be the router internet ip address.

  existing routes need to be removed:

  No route outside 0.0.0.0 0.0.0.0 192.298.47.182 255

  No route outside 0.0.0.0 0.0.0.0 172.35.209.81 in tunnel

  (2) the following declaration of the static NAT is incorrect too and should be removed:

  static (inside, outside) USSLTA01_External USSLTA01 netmask 255.255.255.255

  --> You can not NAT interface on the SAA itself.

  (3) for the SAA within the interface's subnet mask should be 255.255.255.0, no 255.255.0.0. It should be the same as the router interface subnet mask:

  interface Ethernet0/1

  nameif inside

  security-level 100

  IP 192.6.1.254 255.255.255.0

  (4) on the way to access these sub interfaces subnet on the SAA as follows:

  Route inside 192.6.2.0 255.255.255.0 192.6.1.235

  Route inside 192.6.3.0 255.255.255.0 192.6.1.235

  Route inside 192.6.4.0 255.255.255.0 192.6.1.235

  On the router, configure it by default route as follows:

  IP route 0.0.0.0 0.0.0.0 192.6.1.254

• P2-1033W not answer during recovery using HP Recovery Kit

  I try a system recovery using the HP Recovery Kit. Windows 7 is the operating system.

  I insert disc 1 into the computer and it seems to start the process. In a few minutes, he gets to a screen similar to sunlight at the top that shines through a blue sky and the rest of the way. There is no HD activity light or a message on the screen. Only the mouse cursor is on the screen. I want to know if it of the way the process works, or is the computer hung up? The screen is this way for more than 45 minutes. The instructions say the process can take two hours, but it does not say what should I see on the screen if anything.

  Sorry for the delay in response to your suggestion.

  I tried to use the hard disk recovery program. However, the program has never worked for me. I received a message stating that "Recover Manager cannot restore your computer by using the original image. Please contact HP support. "Error code: 0xe0ef0003" this is the reason why I bought the recovery Kit.

  My final solution was to use a new HDD (WD 500 GB) with the recovery kit. I always had problems with the program past fashionable unanswered. The system seems to lock up periodically. I decided that I had a memory problem, so I did a test of memory on the system. The memory also hung up test. I removed the memory stick of 1 GB and run the test again. This time she completed with no blocking. I then put the 1 GB module in the system and run the memory test. This time it completed without any problems. When I finally got the recovery kit program to work once again he completed 100 percent instead of the lock up to 70 percent.

  Instructions for use this recovery kit is very basic, in my opinion. HP want me $49.99 for technical support in answering my question on the way to know if the program actually work load. After paying for the recovery kit I considered not just as a good option. I lost a lot of time because I didn't know if the system fails or if it still worked. I would not recommend this system to anyone. If it belongs to my sister, I would have thrown it out the window a long time ago.

• I am trying to perform a recovery using the "HP Recovery Manager", but I don't know what I should choose to do so.

  Update Code error 80070490

  There, I had a update failed on Windows Vista Service Pack 2 (KB948465).  I tried the Mr. fix it, but the execution software failed.  Some time later, I'm now at the point where all of the updates fail and gives me the error code 80070490.  I tried the system tool - didn't work.  My computer is preinstalled with vista home premium, so I have no disks.  I am trying to perform a recovery using the "HP Recovery Manager", but I don't know what I should choose to do so.  Choose 'The essential system updates for Microsoft Vista SP 1'?  If so, he wants that I uninstall first.  How can I do this?

  Hello

  For any questions about the HP recovery process, contact HP.

  Here is their Web site about this link:

  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c00809678&LC=en&DLC=en&cc=us&product=18703

  This is the Microsoft Information about your error code 0 x 80070490

  'You receive a "0 x 80070490" error code when you use Microsoft Update or Windows Update Web sites to install updates'

  http://support.Microsoft.com/kb/958044

  To make the Installation of repair upgrade in the Microsoft link, borrow Microsoft Vista DVD a friend.

  Here is the information on how to do it:

  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  See you soon.

• You are able to use the CD of Windows Vista operating system on a laptop that has Windows 7 Home on it to use the Interface of Windows Vista?

  My situation is that I have a laptop that is a Windows 7 machine. I have a need where I'm considering purchasing a CD of Windows Vista operating system. It comes to be able to use the Interface of Windows Vista? I have a technical support of experience under my belt and I remember that if you need to have a different operating system available that you can use this operating system without installing it on your system.

  I really could use a version of Windows Vista now my educational purposes. My current computer has Windows 7 home running on it right now. Could you or someone give me Options to work with. I'll look forward to your response.

  Thank you

  Gary

  Q: "you are able to use the Windows Vista OS CD on a laptop that has Windows 7 Home above to use the Interface of Windows Vista?"

  A.  No.

• disable the cisco ASA connection using only activate password via asdm

  Hi all

  How to disable the connection to my cisco asa 5520 using only activate password via asdm? I like to asdm connection using the user name and password. TIA!

  The command:

   aaa authentication http console LOCAL

  .. .will be force users accessing to ASDM (which uses transport http (s)) to be authenticated on the LOCAL database.

  You can also specify another list of defined authentication method, such as RADIUS, RADIUS or AD. (Although t wew love to leave a LOCAL method on the spot, in which case your external authentication server is not available.)

• Enable the VLAN on sub interface internet access but block traffic to VLAN native

  I have a 2821 router w / MLS 2024 switches.  Native VLAN(default vlan) is my private network and VLAN 100 is my comments system.  Below is my interface config...

  interface GigabitEthernet0/1

  Description ES_LAN, ETH - LAN$ $$

  IP 10.1.0.2 255.255.0.0

  penetration of the IP stream

  IP nat inside

  IP virtual-reassembly

  automatic duplex

  automatic speed

  !

  !

  interface GigabitEthernet0/1.1

  encapsulation dot1Q 100

  IP 10.3.1.254 255.255.255.0

  penetration of the IP stream

  IP nat inside

  IP virtual-reassembly

  !

  IP default-gateway xx.xxx.xxx.xxx

  IP forward-Protocol ND

  IP http server

  23 class IP http access

  local IP http authentication

  IP http secure server

  IP http timeout policy slowed down 60 life 86400 request 10000

  Default route is defined...

  IP route 0.0.0.0 0.0.0.0 xx.xxx.xxx.xxx

  Access list are...

  access-list 175 deny ip 10.1.0.0 0.0.255.255 10.2.0.0 0.0.255.255

  access-list 175 allow ip 10.1.0.0 0.0.255.255 everything

  access-list 175 deny ip 10.3.1.0 0.0.0.255 10.1.0.0 0.0.255.255

  access-list 175 allow ip 10.3.1.0 0.0.0.255 any

  I want to continue to have access to the guest VLAN in VLAN private to allow the management of points of access etc.

  I want to allow internet access as guest newtork but block it to access my private network.

  Don't know how to do in this regard.  I tried to change the ACLs (remove the 10.3.1.0 entries) and creating an another acl for the Scriptures and applying that VLAN 100 sub interface... so far without success.

  Thanks in advance for the help!

  Hello Chris,

  > From this point of view should I leave the above lines and create another list acl for the 10.3.1.0 of the network and apply entering gig0/1.1?

  I would go this way, as in a simple ACL, you can't express your needs. The ACL to apply on gi0/1.1 will probably need further instructions then the ones I suggested, but divide the problem into smaller manageable pieces is a good strategy.

  > Also with this config would be NAT be performed on each network by making this change?

  Until the internal network and network of comments are on the same side (ip nat inside) there is no NAT triggered in communication between them so that you should not influence the NAT configuration with this change.

  Hope to help

  Giuseppe

• ACS appliance multiple use of interface

  Is it possible for me to use both interfaces are available in the 1113 box? I want to connect these two interfaces to two separate network segments. I did find something specific in the Cosole except the fixed ip that would be only an interface unique config.

  Thank you

  You can use only one.

  Your system of 1113 Cisco integrated 10/100/1000 megabits - per second (Mbps) Ethernet connectors. ACS SE takes care of the operation of an Ethernet connector, but not the two connectors.

  For more check here

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_solution_engine/4.1/installation/guide/solution_engine/ovrvuap.html#wp1054065

• Can I use a dimension of import command line using table interface?

  Hi guys

  I'm using EPMA to load dimensions by using the interface of the table, but I want to know if it is possible to launch using a command line?

  Concerning

  Yes, use client batch epma, have a read of http://john-goodwin.blogspot.com/2011/11/loading-to-epma-planning-applications.html

  See you soon

  John

  http://John-Goodwin.blogspot.com/

• Recovery using backup Controlfile...

  Hi all
  
  I have a little doubt about the recovery process...
  
  Suppose I took a cold backup (after immediate stop).
  After that, I started the database, made a newspaper change and delete the control file.
  
  In this case when I try to recover the database by using a backup controlfile (recover database using backup controlfile), I need to provide the name of the log file manually
  to ensure no loss of data during the recovery process.
  After that, I need start the database with the RESET LOGS.
  
  
  But my question is why the database will force you to RESETLOGS even if you haven't lost all the data or you haven't made an incomplete recovery.
  
  
  Thank you...

  >
  Suppose I took a cold backup (after immediate stop).
  After that, I started the database, made a newspaper change and delete the control file.

  In this case when I try to recover the database by using a backup controlfile (recover database using backup controlfile), I need to provide the name of the log file manually
  to ensure no loss of data during the recovery process.
  After that, I need start the database with the RESET LOGS.

  But my question is why the database will force you to RESETLOGS even if you haven't lost all the data or you haven't made an incomplete recovery.
  >
  It's the RESETLOGS forcing resynchronization of the control file.

  A control file "backup" is a copy and is supposed to be an older file so it needs to be synchronized with the redo log using RESETLOGS files.

  See the doc of SQL language
  http://docs.Oracle.com/CD/B28359_01/server.111/b28286/statements_1004.htm
  >
  RESETLOGS. NORESETLOGS clause determines if Oracle database resets the current sequence number to 1, archives logs not archived (including the active log) and eliminates any information redo that was not implemented during recovery, ensuring that it will never be applied. Oracle database using NORESETLOGS automatically except in the following specific situations, which require a framework for this clause:

  You must specify RESETLOGS:

  After completing the incomplete media recovery or media recovery using a backup control file

• Correct way to use Bind variables when you use an interface to MS SQL Server

  Hey,.
  I have some difficulty to find how to use bind variables in a view, when you use an interface to MS SQL Server. For some reason when I use an ApplicationModule who has a library of MS SQL Server JDBC loaded and I try to click on OK when you change the following query:
  
  SELECT kit_status, component_id
  OF numbered_inv
  WHERE trialname =: 1
  
  I get an error stating that ' SQL Query Error Message incorrect syntax near ':'. JDeveloper is compatible with SQL server for bind variable as this query works fine if I replace the: 1 with a Word to say "Test test".
  
  Thanks in advance
  
  Edited by: NullCheck December 15, 2010 14:06

  Use positional JDBC Style Binding to bind variables
  Try to use? Instead of:
  As shown here:
  http://www.Oracle.com/technetwork/developer-tools/jdev/multidatabaseapp-085183.html

• When to use the interface and use when substituted

  I'm so confuse to use interface and substituted. Please give me some example practice how it is practically used in our daily lives.

  There is a lot of info that you may find yourself on the use of interfaces and by substituting methods. But I say, you do not use one or the other - they are quite different things. An interface is like a contract that specifies a class contain certain methods - those defined by the interface. The interface is just a summary of the class with the signatures of method only - no actual code. Substitution of a method, it is when your method of the upper class is used instead of this method is inherited from its superclass.

• The ASA can use 2 dynamic cryptographic cards on the external interface?

  We have an ASA which is currently used with dynamic VPN. I don't know the pre-shared key.  If I was going to try to create another card encryption. I did not want to bring another drop.  I know that the router does not allow.  It would replace the existing info.  I wasn't sure of the SAA.

  David,

  The pre shared key is defined in the specific tunnel-group, not in the crypto map.

  tunnel-group ipsec-attributes

  pre-shared key cisco

  However, by default:

  Dynamics of LAN-to-LAN tunnels using the 'DefaultL2LGroup '.
  

  L2TP/IPsec connections use the 'DefaultRAGroup '.
  

  In order to see the pre shared key in clear text: "more system: run".

  You can have a single card dynamic encryption card crypto, but you can have multiple entries / map instances of this dynamic, for example:

  Crypto-map dynamic dynamic_map 10 the value transform-set ESP-AES-256-SHA
  

  Crypto-map dynamic dynamic_map 20 the value transform-set ESP-AES-192-SHA
  

  
  

  map outside_map 65535-isakmp ipsec crypto dynamic dynamic_map

  More info:

  Dynamic IPsec Tunnel between a statically addressed ASA and dynamically addressed Cisco IOS router that uses the example of Configuration of CCP

  ASA/PIX: Allow the tunneling split for the VPN Clients on the example of Configuration of ASA

  
  

  Let me know if you have any other questions.

  Portu.

• The ASA Independand IP management interface

  Hello

  I have a pair of ASA 5510 running like a pair of failover 8.4.

  Currently, we have 3 interfaces prod and are also using the management interface in the form of a group management interface.

  AS I joined the two using failover, the interface of management on the second ASA took the IP address of the first. Is it possible to exclude this HA interface so that we can manage, via IP, each device independently? The main reason for this is that two devices sit in different DC so we have another out-of-band to each site network.

  Thank you

  Anthony

  Hello

  I have not personally at least knows of anyway to do this because the devices share the same configuration and switch interface IP address depending on which device is active in the pair.

  To my knowledge each physical interface that is not configured for subinterfaces should be part of the default recovery. I guess in your case, even if it is not accomplish what you're after, you should probably configure "without monitor-interface", if not, to my knowledge, it might affect the State of failover?

  I don't know if there really is a way to make it work as you want. I think Cisco assumes that the management interface is like any other data interface in failover and it requires connectivity between sites where pairs of ASA.

  I guess it would be better if the Console port has been used for this purpose and you had a separate device you can remote access to the Console of the machine you want.

  If you want to send commands to the other ASA the failover and link then it is possible

  For example, you can connect to an ASA and execute commands from the failover link

  exec failover partner

  But again, I don't know if this will be of any help in your situation.

  -Jouni