The ASA Independand IP management interface

Similar Questions

• Questions on the WLAN and AP Manager interface

  Hello

  In fact, I was searching in the internet for more information on the (the AP Manager interface), I've only had the following link on the configuration of WLC.

  http://www.Cisco.com/en/us/docs/wireless/WCS/7.0/Configuration/Guide/7_0admin.html

  -If you have more information about this interface, share with me pls

  My second question is about the WLAN. In fact, I connected the AP lightness to the controller directly via a private network and configured WLAN with SSID. The question im face that customers can see the SSID, but can not be associated. I mean the packets sent is complete but the packets received too low, so I can't access the net.

  How can I solve this problem?

  Should I SWITCH to connect 3 AP light to the controller and the location device? or its just to connect these APs and the controller directly to our private network, because we use the same subnet.

  Thank you

  concerning

  Hello

  The link below can give u some info and you can be knowing this as well

  http://www.Cisco.com/en/us/docs/wireless/controller/5.2/configuration/guide/c52mint.html#wp1117288

  Then regarding the WIFI network... If you are able to see the SSID but not able to associate... What is the quthentication and the encryption is we help? We receive the IP or not?

  Private network means? the WLC will connect to the switch, right?

  Let me know if that answers your question...

  Concerning
  Surendra
  ====
  Please do not forget to note positions that answered your question and mark as answer or was useful

• appvolume Setup is complete but get error below when opening the web app-volume Manager interface. Cannot start the volume App Manager "cannot load this file - tiny_tds.

  "failed to start volume App Manager" boot failure Unable to load the file of this type - tiny_tds

  

  Hi Paul amstaur,.

  This question says, I've met before, and there is a permission problem. Please do below things to get rid of.

  Since you have already installed the app volume, go back to the snapshot, or install a vanilla OS. Provide a sufficient permission in the local security policy, if you install SQL express as well as the volume of the app as the backup Administrator, debug as an administrator, log in as a service to the domain user. Also make sure the time is correct on the computer. You must restart the computer after you gave permission.  Most of the cases you already have full filled what mentioned above, but still you get an error.  To get rid of it, you must copy the appvolume installation files to the local directory, may be in the C drive and recommending only not to mount the ISO in virtual CD ROM, instead of copy and extract the ISO locally.  the next important thing is that you must run the setup.exe AppVolume run as administrator.

• have a cisco CISCO2106 wireless controller. I have configured mangement interface and AP-Manager in this. I can now connect to WLC, through the management interface, but the problem is AP-manager interface to SURVEY not so AP aren't the assoc

  

  What do you mean that's not upward? Can you please upload config and debug? What output do you see on the side of the AP using the console port?

  What is the method of discovery?

• Administration of the ASA via IPSec VPN

  Recently, I upgraded my ASA5505 8.2.1 7.2 and curiously lost the ability to manage a VPN (via ASDM or SSH) unit. Before the upgrade, I was able to connect via a method without problem through the VPN. Internally, I still have no problem.

  The fault on the ASDM client message when I try to connect to remote is "Impossible to launch the 10.x.x.x:4444 Device Manager." If I look at the output of the console mode of information, I see later that there is a "completed by interception TCP Flow' regarding the conversation between ASA and my system remotely.

  The config lines are (I've got running on 443 webvpn):

  http server enable 4444

  255.x.x.x http inside 10.x.x.x

  http 192.x.x.x outside 255.x.x.x

  The 192 is located the beach DHCP VPN that get VPN clients (and I checked) such that these systems are able to connect to the ASDM or SSH management interface.

  Is there another ACL I need to make this work? Not sure why it worked without problem on 7.2 and as soon as I upgraded to 8.2.1, he stopped, without changing the config (manual).

  Thanks in advance for the help!

  Point VPN network ssh interface inside rather than the outside, should work, while vpn - ssh to the asa inside the ip address of the interface.

  without ssh 192.x.x.x 255.x.x.x outdoors.

  SSH 192.x.x.x 255.x.x.x inside.

  Concerning

• 4240 IPS management interface MAC address

  Hi all

  I use DHCP in my network. And I need to book a single IP address for the Interface of management of the IPS.

  I tried to get the MAC but could not. It is not yet on the Show of support.

  Can a please tell me how to get the MAC address IP management interface?

  If the interface to see the output does not give you this information, you can connect via the service account and run the command "ifconfig - a". Just make sure you do a 'su' - otherwise this command is not available.

  Please note if useful :)

  Concerning

  Farrukh

• How do the management interface of configuration of an ethernet interface?

  We have an ASA 5540 requiring a LAN port for failover. And the left side of the interface available only the management port. How do the management interface of configuration of an ethernet interface?

  You can disable the mode of management only on this interface to make as regualr routable port and use for other purposes, including the purposes of failover LAN database.

  On the management interface - 5510 but applies generally to the management0/0, itself including 5540

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/intParam.html#wp1057800

  Basic LAN failover configuration

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/intParam.html#wp1057800

  Rgds

  -Jorge

• ASA management interface

  After reading the management description of the command. It seems that only management traffic to the ASA is allowed on this interface (ASDM, Telent, SSH). It cannot be used for NTP, SNMP, or logging. Is that correct. Thank you

  the documents given the management interface only will accept only incoming traffic. SNMP, as will be the outgoing traffic, NTP will not work... you can convert the dedicated management0/0 port in a port routed by way of licensing for asa5510 and higher.

  The low port out-of-band management of the table reference.

  http://www.Cisco.com/en/us/products/ps6120/prod_models_comparison.html

  the rate of all useful messages.

  Rgds

  Jorge

• Can not handle the ASA inside the interface of Site to Site VPN

  Hi all

  I was deploying new site to site between ASA 8.0 (HQ) and ASA 8.4 (branch). Everything works fine but I have a problem on the ASA-reach remote that I can't manage branch ASA with inside the interface IP address.

  My setup on remote ASA

  management-access inside

  ICMP allow any inside

  SSH 0.0.0.0 0.0.0.0 inside

  SNMP-server host inside 10.0.1.101 communitry test-snmp version 2 c

  My Test

  -ping of the AC for inside the interface of remote ASA

  • Client time-out see demand
  • When debug icmp on ASA remote then ASA show only ICMP request to HQ no response back from remote ASA

  I'm not sure whether it's a bug on ASA 8.4 or not because I can manage a remote other ASA what version 8.0 software HQ

  Thanks in advance

  Do not know what 8.4 version you use, but it is broken in the 8.4 (2), I stumbled upon the upgrade from same problem. SSH and ASDM will not connect through a VPN L2L interface inside. This worked well in 8.4 (1).

  CSCtr16184

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtr16184

  [email protected] / * /.

• EqualLogic group member network configuration error: "management interface should not be on the san subnet.

  Hello

  We currently have new EqualLogic 6100 device with this network configuration:

  Director of the IP - 192.168.0.2 (VLAN1).

  Member network config:
  eth0 - 192.168.0.3 (VLAN1)
  eth1 - 10.10.10.3 (VLAN2)
  eth2 - 10.10.10.4 (VLAN2)
  eth3 - 10.10.10.5 (VLAN2)
  ETH4 - empty

  I would attribute 192.168.0.4 to eth4, but received the error: "management interface should not be on the san subnet.

  I am sure that all interfaces eth has access to the VLAN1 and VLAN2, mean error indicates that eth4 should not access VLAN2 and only access the VLAN1 on the switch?

  Or eth0 should also have access to the VLAN2 only to reconfigure eth0 and eth4?

  Thank you

  > The group eating IP should be in iscsi VLANS?

  Yes!

  Note: If configure you an EQL it will ask an iSCSI port because nothing is more necessary to bring it up. The doest previous EQLs have a dedicated Mgmt Port and later, you can convert the last ethX as a MGMT port. This is the reason why configure you ISCSI at the beginning. (Think of a mixed group of newer and older models, and you get a picture)

  OK... once again it is the one and only member of the Group and there is making the production host connected to the right?

  The change of IP address, to a 3rd. subnet for temporary use.

  -Do not touch eth0-3 and the IP address of the group now

  -Configure the MGMT port and IP address management in the tempr group. Subnet. Use the Config-> Adv. Group-> network MGMT. You can change the MGMT Port of the Member, and the address IP of MGMT

  -For the registration of the configuration, you will lose access. You must place your admin PC in the templ. subnet so

  -Connect to the GroupMgr with temp again. INTELLECTUAL PROPERTY

  -Now you can change the IP address of group 10.10.10..x

  -Now you can change eth0 10.10.10.2

  -At the end, you can change the address IP of the Group MANAGEMENT, as well as the MGMT Port to 192.168.0.x

  -Change the IP address of your admin PC rear

  A failover, you should consider to hang a serial cable the active controller of the EQL. Use 9600,8,1, N with your favorite terminal program (putty.exe on windows). All the steps, you can perform from the command line.

  If this group and the only member not in production, but you can reset the config and restart from the beginning.

  Kind regards

  Joerg

• No access to the interface of the ASA by behind the other is

  Hello

  I am faced with the issue of not being able to access the interface of "dmz" behind the interface 'internet '.

  Here is a brief description of the topology:

  

  List entry on the internet access "," allows for 1xx.xxx.172.1 traffic.

  No nat is configured between these interfaces.

  The routing is OK because hosts on the DMZ network are accessible from the Internet.

  The software version is 9.1 (3).

  Security level of the interfaces is the same.

  Security-same interface inter traffic is allowed.

  Here's what packet trace says:

  tracer # package - entry internet udp 7x.xxx.224.140 30467 1xx.xxx.172.1 det 500

  Phase: 1
  Type:-ROUTE SEARCH
  Subtype: entry
  Result: ALLOW
  Config:
  Additional information:
  identity of the 255.255.255.255 1xx.xxx.172.1

  Phase: 2
  Type:-ROUTE SEARCH
  Subtype: entry
  Result: ALLOW
  Config:
  Additional information:
  identity of the 255.255.255.255 1xx.xxx.172.1

  Result:
  input interface: internet
  entry status: to the top
  entry-line-status: to the top
  the output interface: NP identity Ifc
  the status of the output: to the top
  output-line-status: to the top
  Action: drop
  Drop-reason: (headwall) No. road to host

  Please help me find the cause why asa is unable to find the path to its own interface.

  Thank you in advance.

  Hello

  You will not be able to connect to an IP address of an interface ASA behind another ASA interface. It is a limit that has been there for Cisco firewalls as long as I can remember.

  The only exception is when you have a VPN connection that is connected to an ASA interface, then you can connect through this VPN connection to another interface of the ASA. In this case the ASA will also require that you have the following command

  access to the administration

  Where is the name of the interface to which you are connected.

  -Jouni

• How to set up the AP Manager interface on vWLC

  Hello all,.

  I want to bulid a laboratory wireless env, vWLC is used, but I can't find where I could configure AP Manager interface vWLC.

  How do I creat an interface of the AP Manager?

  Thank you for your help.

  1.How many APs could this Dynamic AP Management support ?

  No limitation on the interface. It all depends on how can license AP you have on your vWLC

  2.We can't creat AP manager interface on vWLC like real WLC , right ?

  Yes, good. New platforms of controller, there is only the interface of management exist. There is no separate AP Manager interface.

   3.How can I distinguish my AP's  "Country Code"  ?

  If you look at your reference number AP (see the version should also give this), it indicates a regulatory domain (for example - A,-E, n, z). This means that your vWLC set up with a country code in this regulatory area. The document below for more details http://www.cisco.com/c/en/us/products/collateral/wireless/access-points/product_data_sheet0900aecd80537b6a.html * don't forget to rate our answers if you find them useful * HTH Rasika

• Dynamic management of the mobile AP management interface to another dynamic interface (WLC 2504)

  Situation/configuration is the following:

  -2504 WLC (8.1.131) with a total of 22 AP is connected.

  -Several WLAN active each with its own interface (dynamic)

  -L' (static) management interface is the option "Activate the dynamic management of AP" enabled.

  -The four physical interfaces of the WLC remain TROLLING configured.

  What is the problem:

  In the current configuration, the management interface is in the same vlan as the AP we now want to move the management interface to a different VLAN, but keep the AP in the vlan current. The idea is to move the management interface to its new vlan and disable "enable dynamic management of AP". Then, create a new interface (dynamic) in the same vlan as of AP and select 'turn on the dynamic management of AP' on this interface. Configure it as it is no problem but is does not work. The AP will record is no longer with the WLC.

  Is there something I may be missing why this does not work?

  Richard.

  Yes, that's the gist of it.

  I recommend always making a capture packets if only just for educational purposes and to see how this works in action. I found it interesting when I did in the lab here.

• How to block ping the ASA 5506 outside interface?

  I configured a Cisco ASA VPN configuration and Setup. Everything works fine. The SAA outside interface is to pings (on the internet) which is a threat to security. How to only block ping to the external interface without interrupting the functions of the ASA. I tried what follows, but does not seem to work.

  outside the IP = 169.215.243.X

  ASA 2.0000 Version 2

  Access list BLOCK_PING refuse icmp any host 169.251.243.X echo-reply

  Access-group BLOCK_PING in interface outside

  You have set up the ACL is only for traffic that gets sent through the ASA, ASA traffic is controlled in different ways. For ICMP, you can refuse the rattling of the SAA and that allows all other ICMP with the following configuration:

  icmp deny any echo outsideicmp permit any outside

  It is also possible to ban all ICMP:

  icmp deny any outside

  The 'truth' is probably somewhere between these two options. It's your choice.

• The traffic load between the power of Cisco ASA and FireSight Management Center fire

  Hi all

  I have a stupid question to ask.

  Can I know what is the traffic load and the e/s flow between firepower Cisco ASA and FireSight Management Center?

  Currently working on a project, client require such information to adapt to their network. Tried to find in the document from Cisco, but no luck.

  Maybe you all have no idea to provide.

  It varies depending on the number of events reported from the module to the CSP. No event = only health controls and policy changes are exchanged. 10,000 events per second = much more traffic.

  Generally it is not a heavy load, however.