ASA5505 management via VPN/Anyconnect without group

Similar Questions

• Access via L2L AnyConnect VPN IPSec

  I'm trying to connect two ASA 5505s for a IPSec L2L VPN.  They can connect, but not pass traffic from the AnyConnect subnet. I've added the config from ASA-2, with the LAN subnet of 192.168.138.0 and a subnet of 192.168.238.0 for AnyConnect client. I'm trying to get the AnyConnect Clients access to the 192.168.137.0 LAN behind ASA-1 at 1.1.1.1.  Having both 192.168.238.0 and 192.168.138.0 both access 192.168.137.0 is acceptable. There's probably a lot of cruft in this config, as I've been reading all over forums and docs without much success.  Can someone point me in the right direction? : ASA Version 8.2(1) ! hostname asa-wal names name 192.168.238.0 anyconnect-vpn ! interface Vlan1 nameif inside security-level 100 ip address 192.168.138.1 255.255.255.0 ! interface Vlan11 mac-address c03f.0e3b.1923 nameif outside security-level 0 ip address 2.2.2.2 255.255.255.248 ! same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service Munin tcp-udp port-object eq 4949 object-group service Webmin tcp port-object eq 10000 access-list inside_nat0_outbound extended permit ip 192.168.138.0 255.255.255.0 any access-list icmp_ping extended permit icmp any any echo-reply access-list icmp_ping extended permit ip 192.168.138.0 255.255.255.0 any access-list split-tunnel standard permit 192.168.138.0 255.255.255.0 access-list 100 extended permit icmp any any echo-reply access-list 100 extended permit icmp any any time-exceeded access-list 100 extended permit icmp any any unreachable access-list NO_NAT extended permit ip anyconnect-vpn 255.255.255.0 any access-list NONAT extended permit ip 192.168.138.0 255.255.255.0 anyconnect-vpn 255.255.255.0 access-list outside_access_in extended permit tcp any interface outside eq ssh access-list outside_access_in extended permit icmp any any echo-reply access-list outside_access_in extended permit icmp any any time-exceeded access-list outside_access_in extended permit icmp any any unreachable  access-list outside_access_in extended permit tcp 192.168.137.0 255.255.255.0 anyconnect-vpn 255.255.255.0 access-list outside_1_cryptomap extended permit ip anyconnect-vpn 255.255.255.0 192.168.137.0 255.255.255.0 access-list inside_nat0_outbound_1 extended permit ip 192.168.138.0 255.255.255.0 anyconnect-vpn 255.255.255.0 access-list inside_nat0_outbound_1 extended permit ip anyconnect-vpn 255.255.255.0 192.168.137.0 255.255.255.0 access-list LAN_Traffic extended permit ip anyconnect-vpn 255.255.255.0 192.168.137.0 255.255.255.0 access-list vpn_nonat extended permit ip anyconnect-vpn 255.255.255.0 192.168.137.0 255.255.255.0 ip local pool AnyConnect 192.168.238.101-192.168.238.125 mask 255.255.255.0 global (outside) 1 interface nat (inside) 0 access-list NONAT nat (inside) 2 access-list vpn_nonat nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface ssh 192.168.138.4 ssh netmask 255.255.255.255 access-group icmp_ping in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 2.2.2.1 1 dynamic-access-policy-record DfltAccessPolicy network-acl inside_nat0_outbound network-acl NO_NAT aaa authentication ssh console LOCAL http server enable http bobx-vpn 255.255.255.0 inside http 192.168.137.0 255.255.255.0 inside http 192.168.1.104 255.255.255.255 inside http 192.168.138.0 255.255.255.0 inside http anyconnect-vpn 255.255.255.0 inside http redirect outside 80 no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set Wal2Box esp-aes-256 esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map outside_map 1 match address outside_1_cryptomap crypto map outside_map 1 set pfs group1 crypto map outside_map 1 set peer 98.110.179.36 crypto map outside_map 1 set transform-set ESP-3DES-SHA crypto map Wal2Box 1 match address LAN_Traffic crypto map Wal2Box 1 set peer 98.110.179.36 crypto map Wal2Box 1 set transform-set Wal2Box crypto map Wal2Box interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 5 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 10 authentication pre-share encryption des hash sha group 2 lifetime 86400 crypto isakmp nat-traversal 22 telnet timeout 5 ssh 192.168.138.0 255.255.255.0 inside ssh timeout 30 console timeout 0 management-access inside dhcpd dns 8.8.8.8 8.8.4.4 dhcpd auto_config outside ! dhcpd address 192.168.138.101-192.168.138.132 inside dhcpd dns 8.8.8.8 8.8.4.4 interface inside dhcpd lease 86400 interface inside dhcpd domain inc.internal interface inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 129.6.15.29 ntp server 129.6.15.28 prefer webvpn enable inside enable outside anyconnect-essentials svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1 svc enable tunnel-group-list enable group-policy DfltGrpPolicy attributes vpn-filter value NO_NAT vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn split-tunnel-network-list value split-tunnel webvpn   svc compression deflate group-policy Wal-AnyConnect internal group-policy Wal-AnyConnect attributes split-tunnel-policy tunnelspecified split-tunnel-network-list value split-tunnel tunnel-group DefaultRAGroup general-attributes address-pool AnyConnect default-group-policy Wal-AnyConnect strip-realm strip-group tunnel-group AnyConnectClientProfile type remote-access tunnel-group AnyConnectClientProfile general-attributes address-pool AnyConnect default-group-policy Wal-AnyConnect tunnel-group AnyConnectClientProfile webvpn-attributes group-alias AnyConnectVPNClient enable tunnel-group 1.1.1.1 type ipsec-l2l tunnel-group 1.1.1.1 ipsec-attributes pre-shared-key * ! class-map global-class match default-inspection-traffic ! ! policy-map global-policy class global-class   inspect pptp ! Cryptochecksum:762f0186ad987cda4b450f6b4929cb60 : end 

  Post edited by: Shawn Barrick - line breaks

  It seems good Shawn but I just noticed an error on the asa-wal, you have a vpn-filter applied on the DfltGrpPolicy and since you have not any value defined the strategy of Wal-AnyConnect group then will inherit the DfltGrpPolicy vpn-filter, don't forget that the vpn filters should be applied to the incoming direction, I mean pool resources you want them to have access to. It's the ACL you have for the filter:

  NO_NAT list extended access allowed anyconnect vpn - ip 255.255.255.0 everything

  This isn't in the inbound direction, increasingly looks like you want to allow access to what it is as long as the traffic is coming from the 192.168.238.0, if that's the case, you can do this:

  attributes of Group Policy DfltGrpPolicy

  VPN-filter no

  Do not forget to disconnect and reconnect after the above change...

  If you really need to be more specific, allowing traffic for clients then apply the inbound rules, for example:

  Your pool is here 192.168.238.0/24 and the local subnet is 192.168.138, to this effect, the 192.168.137 is considered to be local too because of the perspective Anyconnect we'll see in the room even if it is a remote network accessible via a L2L tunnel of the Anyconnect client does not.

  The following AS will allow the Anyconnect Telnet client for local networks:

  permit access-list vpnfilt-ra 192.168.238.0 255.255.255.255 192.168.138.0 255.255.255.0 eq 23

  permit access-list vpnfilt-ra 192.168.238.0 255.255.255.255 192.168.137.0 255.255.255.0 eq 23

  The following ACE will allow local networks of Telnet for the Anyconnect Client:

  permit access-list vpnfilt-ra 192.168.238.0 255.255.255.255 eq 23 192.168.138.0 255.255.255.0

  permit access-list vpnfilt-ra 192.168.238.0 255.255.255.255 eq 23 192.168.137.0 255.255.255.0

  Note that the two first ACE will allow LAN launch connection to the Anyconnect client on any TCP port if he uses a source 23 port while the last two ACEs allow the Anyconnect client connect to networks the on any TCP port if he uses a port source from 23.

  Kind regards

• Help blocking smart devices of via VPN

  Hello

  I am looking for a solution block smart devices to connect to our network via VPN. Our VPN solution today is ASA5520, and we use Cisco ACS to authenticate the user. We use Cisco VPN client only, no anyconnect or SSL VPN.

  Managment is looking for a way that we can stop the smart devices of using VPN clients to connect and allow only desktop computers laptops to connect.

  Someone at - there a way we can do this through association or another method?

  Worring - I block iPhones & iPad around my overall networkwith 100% accuracy with a few simple lines of config: -.

  Group Policy <> attributes

  client-access-rule 1 deny version of type 'iPhone OS. "

  2-client-access rule allow type * version *.

  As it actually works on the OS - not the version of the Cisco VPN Client device.

• Check sensor SFR with FireSight via VPN - does not work

  Hello security experts.

  I have an ASA5515-X with SFR installed 5.4.0 and manage with 5.4 FireSight installed on the virtual machine on LAN and I record the sensor without any problem but when I try to register the sensor to FireSight via VPN I can't do. The interface on the ASA management has no intellectual property nor nameif configured and the interface is connected to the switch, SFR has the IP even configured as LAN addressing. I can see traffic being exchanged between the sensor and the FireSight but I can't save the sensor.

  Has anyone managed to register the sensor via VPN? Is there something else to be configured in order to save the sensor with the MC via the VPN?

  The delay between the Firesight and the sensor (on WAN and VPN) I get between 80 and 100 ms, what could be the problem?

  Thank you very much!

  Remi

  Hello

  If you are unable to telnet from DC to the sensor on the port 8305 delivers connectivity then.

  Can try you to ping from sensor to DC:

  ping -M do -c 20 -s 1572 

  By default, the MTU is 1500 on eth0, if the ping does not work I will suggest to lower the MTU on the interface and see if it works. See also: / var/log/messages | grep sftunnel and see the error messages on DC and sensor and send it to me everywhere. Best regards, Aastha Bhardwaj rate if this is useful!

• ASDM running via VPN

  Configuration management an ASA 5510 to my workstation access when connected via the AnyConnect client: I need help.  The VPN works fine and I can connect to what anyone on the remote site, but it will not allow ASDM / SSH to the ASA on the remote side of the tunnel.  I have an IP address assigned to my computer always has the same address, and I have access to the administration has allowed since this address inside and outside interfaces.  But I must be mising something.  No problem with access to the administration of the inside of the network.  Thanks for any help.

  If you try to access the inside interface of the ASA on the VPN tunnel, then please add the following:

  management-access inside

  You must add the following as well:

  SSH inside

  HTTP inside

  Hope that helps.

• ASA 5520 - SSL VPN (Anyconnect) licenses

  Hello

  Can someone clarify for me the SSL VPN/AnyConnect for the ASA 5520 license?  Specifically, the differences between the AnyConnect Essentials and AnyConnect Premium.  Our current license looks like this:

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited
  VLAN maximum: 150
  Internal hosts: unlimited
  Failover: Active/active
  VPN - A: enabled
  VPN-3DES-AES: enabled
  Security contexts: 2
  GTP/GPRS: disabled
  SSL VPN peers: 2
  Total of the VPN peers: 750
  Sharing license: disabled
  AnyConnect for Mobile: disabled
  AnyConnect Cisco VPN phone: disabled
  AnyConnect Essentials: disabled
  Assessment of Advanced endpoint: disabled
  Proxy sessions for the UC phone: 2
  Total number of Sessions of Proxy UC: 2
  Botnet traffic filter: disabled

  This platform includes an ASA 5520 VPN Plus license.

  I guess that means that we have just the 2 'free trial' SSL VPN licenses and nothing else.

  I would like to add 25 or maybe 50 SSL VPN licenses and be able to use a combination of full free client, thin client and groups client AnyConnect.  The 'ASA5500-SSL-25' (or 50) would be the correct license I need to buy?

  Thank you

  Rob

  Hello

  The essentials license is per device and does not allow full-tunnel.

  If you need other features like Secure Desktop, without client SSL and other optional features such as shared licenses, you must go to the Premium license.

  http://www.Cisco.com/en/us/prod/collateral/vpndevc/ps6032/ps6094/ps6120/data_sheet_c78-527494_ps10884_Products_Data_Sheet.html

  Federico.

• Customer remote cannot access the server LAN via VPN

  Hi friends,

  I'm a new palyer in ASA.

  My business is small. We need to the LAN via VPN remote client access server.

  I have an ASA5510 with version 7.0. I have configured remote access VPN and it can establish the tunnel with success. But I can not access the server.

  Client VPN is 5.0.07.0290 version. Encrypted packages have increased but the decrypted packet is 0 in the VPN client statistics, after I connected successfully.

  Next to the ASA, I show crypto ipsec sa, just deciphering the packets increase.

  Who can help me?

  Thank you very much.

  The following configuration:

  ASA Version 7.0(7)
  
      !
  
      hostname VPNhost
  
      names
  
      dns-guard
  
      !
  
      interface Ethernet0/0
  
      nameif outside
  
      security-level 10
  
      ip address 221.122.96.51 255.255.255.240
  
      !
  
      interface Ethernet0/1
  
      nameif inside
  
      security-level 100
  
      ip address 192.168.42.199 255.255.255.0
  
      !
  
      interface Ethernet0/2
  
      shutdown
  
      no nameif
  
      no security-level
  
      no ip address
  
      !
  
      interface Management0/0
  
      shutdown
  
      no nameif
  
      no security-level
  
      no ip address
  
      management-only
  
      !
  
      ftp mode passive
  
      dns domain-lookup inside
  
      access-list PAT_acl extended permit ip 192.168.42.0 255.255.255.0 any
  
      access-list allow_PING extended permit icmp any any inactive
  
      access-list Internet extended permit ip host 221.122.96.51 any inactive
  
      access-list VPN extended permit ip 192.168.42.0 255.255.255.0 192.168.43.0 255.255.255.0
  
      access-list VPN extended permit ip 192.168.43.0 255.255.255.0 192.168.42.0 255.255.255.0
  
      access-list CAPTURE extended permit ip host 192.168.43.10 host 192.168.42.251
  
      access-list CAPTURE extended permit ip host 192.168.42.251 host 192.168.43.10
  
      pager lines 24
  
      mtu outside 1500
  
      mtu inside 1500
  
      ip local pool testpool 192.168.43.10-192.168.43.20
  arp timeout 14400
  
      global (outside) 1 interface
  
      nat (inside) 0 access-list VPN
  
      nat (inside) 1 access-list PAT_acl
  
      route outside 0.0.0.0 0.0.0.0 221.122.96.49 10
  
  
      username testuser password 123
  
      aaa authentication ssh console LOCAL
  
      aaa local authentication attempts max-fail 3
  no sysopt connection permit-ipsec
  
      crypto ipsec transform-set FirstSet esp-des esp-md5-hmac
  
      crypto dynamic-map dyn1 1 set transform-set FirstSet
  
      crypto dynamic-map dyn1 1 set reverse-route
  
      crypto map mymap 1 ipsec-isakmp dynamic dyn1
  
      crypto map mymap interface outside
  
      isakmp enable outside
  
      isakmp policy 1 authentication pre-share
  
      isakmp policy 1 encryption des
  
      isakmp policy 1 hash md5
  
      isakmp policy 1 group 2
  
      isakmp policy 1 lifetime 86400
  
      isakmp nat-traversal  3600
  
      tunnel-group testgroup type ipsec-ra
  
      tunnel-group testgroup general-attributes
  
      address-pool testpool
  
      tunnel-group testgroup ipsec-attributes
  
      pre-shared-key *
  
      telnet timeout 5
  ssh timeout 10
  
      console timeout 0
  : end
  

  Topology as follows:

  

  Hello

  Configure the split for the VPN tunneling.

  1. Create the access list that defines the network behind the ASA.

     ciscoasa(config)#access-list Split_Tunnel_List remark The corporate network behind the ASA. ciscoasa(config)#access-list Split_Tunnel_List standard permit 10.0.1.0 255.255.255.0 

  2. Mode of configuration of group policy for the policy you want to change.

     ciscoasa(config)#group-policy hillvalleyvpn attributes ciscoasa(config-group-policy)#

  3. Specify the policy to split tunnel. In this case, the policy is tunnelspecified.

     ciscoasa(config-group-policy)#split-tunnel-policy tunnelspecified 

  4. Specify the access tunnel split list. In this case, the list is Split_Tunnel_List.

     ciscoasa(config-group-policy)#split-tunnel-network-list value Split_Tunnel_List 

  5. Type this command:

     ciscoasa(config)#tunnel-group hillvalleyvpn general-attributes 

  6. Associate the group with the tunnel group policy

     ciscoasa(config-tunnel-ipsec)# default-group-policy hillvalleyvpn 

  7. Leave the two configuration modes.

     ciscoasa(config-group-policy)#exit ciscoasa(config)#exit ciscoasa#

  8. Save configuration to non-volatile RAM (NVRAM) and press enter when you are prompted to specify the name of the source file.

  Kind regards
  Abhishek Purohit
  CCIE-S-35269

• Using Windows 7 and 8.1 of Windows via a shared house group the WF-2540 Epson printer is off line.

  Original title: printer is offline

  using Windows 7 and 8.1 of Windows via a shared house group the WF-2540 Epson printer is off line.  This printer uses with two PCs using Windows 7 and a PC using Windows 8 with no problems.  Today it usually just printing using 1 PC with 7-1 8.  It is connected to the PC works well.  This isn't wired wireless we have wireless at the office.   Use this way for years with no problems, then suddenly this morning its all stopped.  I read so much information on it with no satisfactory response.  Epson will not know that it is not connected via radio or directly with a PC, so I'll through in circles.

  I reinstalled the PC on Windows 8 PC nothing works.  Any suggestions as to what I can try next as business has ground to stand without the printer!

  Thank you

  Hello

  Thank you for visiting Microsoft Community.

  I suggest you to post your query on our TechNet Forums social as this question right here.

  Please refer to the reference to the link below to send your request:

  https://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking

  Sincerely,

  Ankit Rajput

• WebVPN and remote vpn, ssl vpn anyconnect

  Hi all

  Differences between webvpn and remote vpn, ssl vpn anyconnect
  All require a separate license?

  Thank you

  Hello

  The difference between the webvpn and SSL VPN Client is the WebVPN to use SSL/TLS and port

  send through a java application to support the application, it also only supports TCP for unicast traffic, no ip address

  address is assigned to the customer, and the navigation on the web in the tunnel is made with a SSL

  Web-mangle that allows us stuff things in theSSL session.

  SSL VPN (Anyconnect) Client is a client of complete tunneling using SSL/TCP, which installs an application on the computer and

  envelopes vpn traffic in the ssl session and thus also an assigned ip address has the

  tunnel's two-way, not one-way.   It allows for the support of the application on the

  tunnel without having to configure a port forward for each application.

  AnyConnect is a client of new generation, which has replaced the old vpn client and can be used as long as the IPSEC vpn ssl.

  For anyconnect licenses please see the link below:

  http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/ANYC...

  Kind regards

  Kanwal

• Site to Site VPN working without Crypto Card (ASA 8.2 (1))

  Hi all

  Find a strange situation on our firewall to ASA5540:

  We have a few Site to Site VPN and also activate on the ASA VPN cleint, all are working properly. But finding that a VPN from Site to Site is running without crypto map configuration. Is this possible?

  I tried to erase isa his and claire ipsec his then VPN came once again. Tested too, it's the ping requests to a remote site through the VPN.

  I saw there are config tunnel-group for VPN but saw no card crypto and ACL.

  How is the firewall knows what traffic should be encrypted for this VPN tunnel without crypto card?

  This is the bug?

  Thanks in advance,

  It can be an easy vpn configuration.

  Could you post output config operation remove any sensitive information.  This could help us answer your question more specifically.

• Share documents via link pages without asking for user name

  Hello, it is possible to share the page via link document without asking user name when someone opens the link? I only want to share the document for reading does not work. So I don't think that it is necessary to request user name.

  Hi erino72,

  Thank you for using communities Support from Apple!

  I understand you want to share a Pages document with someone, without him asking for request a user name.  Given that you're just trying to share a document for reading instead of calibration, then I recommend that you just send a copy by following the steps in the link below:

  Send a copy of a document

  Take care.

• Cannot connect remotely via VPN since installing the new modem/router

  Can anyone help please. Since the acquisition of a new router / modem I can no longer connect via VPN to my work PC remotely. It comes in I receive the error message. Can someone tell me if I need to change the settings for the new modem / router to access?

  

  Hello Joanna,

  Here are the steps you need to do first:

  1. Off static IP for my server and let the router assign IP address and changed the IP address of the port forward.
  2. Check the IP address because obviously, that changed when you plugged into the router again.
  3. Updated to the latest firmware for the router and NIC.

  For more detailed troubleshooting you can refer to this link: troubleshooting common VPN related errors.

  Let us know how it goes.

• Programmatic access to remote files via VPN on Playbook

  Hello

  It is technically possible to download remote files via VPN programmatically?

  I can't find any documentation on this topic.

  Thank you

  Oh, not... I don't think it's possible.

• Hide the AnyConnect VPN AnyConnect GUI Module

  Dear team

  We are wired deployment 802. 1 x with Posture and that NAM is sufficient for us.

  but when installing AnyConnect vpn module must be installed and cannot be avoided, so VPN tab is also visible in the GUI AnyConnect interface,

  I need to disable the VPN tab from the interface chart anyconnect, because it is not used and confusing for end users.

  We have anyconnect-win-4.1.00028-pre-deploy-k9.

  We have a manual installation of AnyConnect on PC or Client Provisioning, we don't use MSI

  Please suggest 'VPN profile' to end users, which will hide this vpn module.

  Thank you

  Ahad

  Your situation is highlighted in the AnyConnect Administrator's Guide as well:

  When you configure the object Configuration AnyConnect to ISE, unchecking the VPN module under the AnyConnect Module selection does not disable VPN on the customer deployed/put in service. You must set VPNDisable_ServiceProfile.xml to disable the VPN AnyConnect GUI tile. VPNDisable_ServiceProfile.xml is on EAC with other files AnyConnect.

  The xml file, you need should be on the AnyConnect downloads page, but is not. There's a BugID noting that (CSCus26084). Work around the BugID does not work for me, but it could for you.

  The profile CAN be found in the msi file - if you open with 7-zip, you can find the file. She is short, so I'll just paste here:

       true  

• Option of DAP for the verification of the registry for remote access VPN Anyconnect v 3.0 + users

  Hi all

  I'm trying to assign the attribute DAP users VPN (Anyconnect 3.0 +) who fulfil certain conditions of registry. When setting up political DAP, while selecting the condition of the register, it is in error as "secure desktop cisco (CSD) is not enabled, CSD should be enabled to configure the registry endpoint attribute. But as I link percevied, to check the attribute registry "scan host' which is integrated in the module anyconnect 3.0 will be charged. So why he asks me to activate the CSD? CSD is really necessary to verify the registry attribute even if we use anyconenct 3.0 +? Any pointer

  The end of the ASA must be activated and more bits based on AnyConnect.

  Notes elsewhere in the link you quoted, it is said ' host Scan automatically identifies the operating systems and service packs on any remote device establishing a clientless SSL VPN and AnyConnect Cisco client session and when the host Scan/CSD or CSD is activated on the SAA. " (emphasis added).

  FYI Cisco is to denigrate these features over time for the Posture of scanning at the ISE in conjunction with the new posture AnyConnect 4.0 module.