ASDM running via VPN
Configuration management an ASA 5510 to my workstation access when connected via the AnyConnect client: I need help. The VPN works fine and I can connect to what anyone on the remote site, but it will not allow ASDM / SSH to the ASA on the remote side of the tunnel. I have an IP address assigned to my computer always has the same address, and I have access to the administration has allowed since this address inside and outside interfaces. But I must be mising something. No problem with access to the administration of the inside of the network. Thanks for any help.
If you try to access the inside interface of the ASA on the VPN tunnel, then please add the following:
management-access inside
You must add the following as well:
SSH inside
HTTP inside
Hope that helps.
Tags: Cisco Security
Similar Questions
-
ASDM conc (ASA) VPN access
I have the script like this:
an ASA, which is the FW, TR making static NAT from the public to the private IP and private IP address add is add conc (another ASA) VPN. I am accessing these devices via the VPN client and I get the address IP of VPN pool set on VPN conc. VPN conc. is in a DMZ VLAN, but it also has connection to the local network segment. Purposes of mgmt, I connect to this VPN through SSH conc via a switch in the local network segment. To use the http access, I have to be on one of the servers that are in the local network segment. Since then, when I set up the VPN connection, I'm sure VPN conc., what can do to access http directly from my PC?
This sets up on the conc VPN:
management-access inside
After that you should be able to use ASDM over the VPN tunnel, by connecting to its inside ip address.
hth
Herbert
(note, I assume the name of the interface connected to the LAN is named "inside", if not adapt at will ) -
Situation: we have a few portable computers test Ubuntu running DHCP servers. We need get the updates and other changes in corporate network sometimes. Today, we turn off the DHCP server, set up to get an IP via DHCP (besides) and make our updates.
Problem: we do not want someone accidentally connect the laptop to the corporate network, while its DHCP server is running.
Question: so, if we go via wifi using a Cisco VPN client, the DHCP server IP addresses above the tunnel?
Thanks for reading.
N ° DHCP uses layer 2 broadcasts to disseminate IP addresses. Because your clients are connected via VPN, there is no contiguity of layer 2. The only way he would accidentally do it is if you have configured an address to support IP dhcp as one of your VPN clients on the network, which I imagine you wouldn't.
-
I have a question to give a static IP address to the VPN clients. I have a Cisco ASA 5510 11 laptops that will be connected via a VPN (Cisco or Microsoft PPTP). For business reasons, I need each laptop to be assigned the same IP every time that it connects. What would be the best way to accomplish this task?
It is certainly possible, but it does not require that you add an IP address to each user name in the configuration. ASA leans on the username entered by the remote user and checks if it has an IP address that is configured with his user name.
You can find the configuration option in the ASDM here: Configuration-> VPN-> General-> users. Editing a user and click the VPN Policy tab, you will find the 'IP address' option at the bottom of the page.
If you want to configure this via the console/telnet/ssh: access the configuration mode and type the following:
name of user attributes
VPN-framed-ip-address
Make sure that the subnet matches the subnet of your already configured ip pool! If you use 192.168.10.0/24 as ip pool, your configuration should look like this:
user testuser name attributes
VPN-framed-ip-address 192.168.10.1 255.255.255.0
The address 192.168.10.1 should now always be attributed to the user "testuser".
I hope that this post helps, please rate if she does!
Kind regards
Michael
-
I have a requirement to increase the size of the partitions of hard drive on one of my virtual machines, which I intend to do using the stand-alone converter. This is a site where the machine virtual is the only server on site (SBS 2003), and I was hoping to be able to do this via a VPN connection rather than having to move to the site. However, I am reconsidering because I feel that it might not work in my situation. It would be even possible to do? Is the process of resizing of the disk inaccessible VM? If so, given that the server is running the VPN software, I would assume that run the disk resizing of the process would be to disconnect my VPN connection.
then use something like extpart
I used extpart on several production win2003 servers. Works a charm. on c:\ while the OS is running.
Some say that close the disk otherwise Manager that you might have problems, but I've left open without error.
From vSphere client, edit the VM and increase the size of the hard drive. Inside the guest, open disk management and refresh to see the extra space, then use extpart.
In the virtual machine is live and in production. No interruption of service. Sweet!
It's amazing, it seems not to be very well known. Reference Dell he released in 2003.
-
windows\system32\vsinit.dll
I try to run CISCO "VPN Client" connect from my PC at home for my work PC.
Then, I get a message:
Validation failed for C:\WINDOWS\System32\VSINIT.dll
Any ideas?
Martin
Hello
Run the checker system files on the computer. Link, we can see: Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe): http://support.microsoft.com/kb/310747
Note that: if he asks you the service pack CD, follow these steps from the link: you are prompted to insert a Windows XP SP2 CD when you try to run the tool on a Windows XP SP2 computer system File Checker: http://support.microsoft.com/kb/900910 (valid for Service pack 3)
If the steps above is not enough of it please post your request in the TechNet forum for assistance: http://social.technet.microsoft.com/Forums/en/category/windowsxpitpro
-
REMOTE DESKTOP cannot connect home via VPN to WORK computer
Hi all
Having problems connecting to the PC of Office WORK PC using remote desktop. Currently, I connect to the WORK PC to WORK laptop with no problems.
Page HOME of PC is a Dell Dimension 4600 Windows XP, version of Microsoft Office Home, ATT, anti-virus Norton 360 Wireless internet service. Work VPN up and running. Set up my computer remote tab in order to allow the communication and remote AUTHORIZED Norton 360 desktop, I can PING my computer work fine.
I run my VPN and connect to function properly the network but when I run the Remote Desktop application, I get "this computer cannot connect to the remote computer."
I know that my work IP address and logon information is exact and know that my work computer is configured to allow remote access because I do this work laptop. I do not understand why my home PC has a problem if the VPN works and I can PING my computer work fine.
Any advice would be appreciated. I looked all over the internet and cannot find additional ideas.
Use teamviewer, it is much easier to understand. And you can give the PC connecting to a fixed password youre. If you do not have to change. Just install on both, give the youre one connecting a password fixed, then log in with the other
Is XP Home or Pro? If it does not support his home desk remotely
-
Cannot connect remotely via VPN since installing the new modem/router
Can anyone help please. Since the acquisition of a new router / modem I can no longer connect via VPN to my work PC remotely. It comes in I receive the error message. Can someone tell me if I need to change the settings for the new modem / router to access?
Hello Joanna,
Here are the steps you need to do first:
- Off static IP for my server and let the router assign IP address and changed the IP address of the port forward.
- Check the IP address because obviously, that changed when you plugged into the router again.
- Updated to the latest firmware for the router and NIC.
For more detailed troubleshooting you can refer to this link: troubleshooting common VPN related errors.
Let us know how it goes.
-
Programmatic access to remote files via VPN on Playbook
Hello
It is technically possible to download remote files via VPN programmatically?
I can't find any documentation on this topic.
Thank you
Oh, not... I don't think it's possible.
-
Check sensor SFR with FireSight via VPN - does not work
Hello security experts.
I have an ASA5515-X with SFR installed 5.4.0 and manage with 5.4 FireSight installed on the virtual machine on LAN and I record the sensor without any problem but when I try to register the sensor to FireSight via VPN I can't do. The interface on the ASA management has no intellectual property nor nameif configured and the interface is connected to the switch, SFR has the IP even configured as LAN addressing. I can see traffic being exchanged between the sensor and the FireSight but I can't save the sensor.
Has anyone managed to register the sensor via VPN? Is there something else to be configured in order to save the sensor with the MC via the VPN?
The delay between the Firesight and the sensor (on WAN and VPN) I get between 80 and 100 ms, what could be the problem?
Thank you very much!
Remi
Hello
If you are unable to telnet from DC to the sensor on the port 8305 delivers connectivity then.
Can try you to ping from sensor to DC:
ping -M do -c 20 -s 1572
By default, the MTU is 1500 on eth0, if the ping does not work I will suggest to lower the MTU on the interface and see if it works. See also: / var/log/messages | grep sftunnel and see the error messages on DC and sensor and send it to me everywhere. Best regards, Aastha Bhardwaj rate if this is useful! -
ASA5505 management via VPN/Anyconnect without group
I have 2 questions about the configuration of the SAA.
The first is related to the SSL VPN configuration. Just one group of users to which you connect to our main office via remote access. Is there a way to configure SSL VPN to not display a group selection?
I have the omission of the list of the groups-tunnel-enable command and configuration group on user accounts locking, but neither work.
Secondly, I am at a loss on how to configure ssh to allow users connected via VPN connections. I guess:
SSH 172.16.1.0 255.255.255.0 inside
with 172.16.1.0 24 is the ip pool assigned to remote access vpn users would do so, however, it's a no go. How can users of remote access (which are for the most part, all technicians) granted the possibility to connect to the device?
Thanks for your help.
To be able to manage the ASA via SSH via a VPN tunnel, you will need to enter the configuration command "in man".
-
Is VLAN via VPN possible with any of the Small Business routers?
A tagged VLAN (for voice) will be routed through a VPN gateway to gateway on any of the Small Business routers, such as the SA520? This router is equipped
Parameters of VLAN Trunking.
No, it is not possible to send traffic to vlan via VPN on a series of SA500, but you can create a tunnel for each subnet, you need to pass traffic.
hope this helps,
Jasbryan
-
Customer remote cannot access the server LAN via VPN
Hi friends,
I'm a new palyer in ASA.
My business is small. We need to the LAN via VPN remote client access server.
I have an ASA5510 with version 7.0. I have configured remote access VPN and it can establish the tunnel with success. But I can not access the server.
Client VPN is 5.0.07.0290 version. Encrypted packages have increased but the decrypted packet is 0 in the VPN client statistics, after I connected successfully.
Next to the ASA, I show crypto ipsec sa, just deciphering the packets increase.
Who can help me?
Thank you very much.
The following configuration:
ASA Version 7.0(7)
!
hostname VPNhost
names
dns-guard
!
interface Ethernet0/0
nameif outside
security-level 10
ip address 221.122.96.51 255.255.255.240
!
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.42.199 255.255.255.0
!
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
!
interface Management0/0
shutdown
no nameif
no security-level
no ip address
management-only
!
ftp mode passive
dns domain-lookup inside
access-list PAT_acl extended permit ip 192.168.42.0 255.255.255.0 any
access-list allow_PING extended permit icmp any any inactive
access-list Internet extended permit ip host 221.122.96.51 any inactive
access-list VPN extended permit ip 192.168.42.0 255.255.255.0 192.168.43.0 255.255.255.0
access-list VPN extended permit ip 192.168.43.0 255.255.255.0 192.168.42.0 255.255.255.0
access-list CAPTURE extended permit ip host 192.168.43.10 host 192.168.42.251
access-list CAPTURE extended permit ip host 192.168.42.251 host 192.168.43.10
pager lines 24
mtu outside 1500
mtu inside 1500
ip local pool testpool 192.168.43.10-192.168.43.20arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list VPN
nat (inside) 1 access-list PAT_acl
route outside 0.0.0.0 0.0.0.0 221.122.96.49 10
username testuser password 123
aaa authentication ssh console LOCAL
aaa local authentication attempts max-fail 3no sysopt connection permit-ipsec
crypto ipsec transform-set FirstSet esp-des esp-md5-hmac
crypto dynamic-map dyn1 1 set transform-set FirstSet
crypto dynamic-map dyn1 1 set reverse-route
crypto map mymap 1 ipsec-isakmp dynamic dyn1
crypto map mymap interface outside
isakmp enable outside
isakmp policy 1 authentication pre-share
isakmp policy 1 encryption des
isakmp policy 1 hash md5
isakmp policy 1 group 2
isakmp policy 1 lifetime 86400
isakmp nat-traversal 3600
tunnel-group testgroup type ipsec-ra
tunnel-group testgroup general-attributes
address-pool testpool
tunnel-group testgroup ipsec-attributes
pre-shared-key *
telnet timeout 5ssh timeout 10
console timeout 0: end
Topology as follows:
Hello
Configure the split for the VPN tunneling.
Create the access list that defines the network behind the ASA.
ciscoasa(config)#access-list Split_Tunnel_List remark The corporate network behind the ASA. ciscoasa(config)#access-list Split_Tunnel_List standard permit 10.0.1.0 255.255.255.0
Mode of configuration of group policy for the policy you want to change.
ciscoasa(config)#group-policy hillvalleyvpn attributes ciscoasa(config-group-policy)#
Specify the policy to split tunnel. In this case, the policy is tunnelspecified.
ciscoasa(config-group-policy)#split-tunnel-policy tunnelspecified
Specify the access tunnel split list. In this case, the list is Split_Tunnel_List.
ciscoasa(config-group-policy)#split-tunnel-network-list value Split_Tunnel_List
Type this command:
ciscoasa(config)#tunnel-group hillvalleyvpn general-attributes
Associate the group with the tunnel group policy
ciscoasa(config-tunnel-ipsec)# default-group-policy hillvalleyvpn
Leave the two configuration modes.
ciscoasa(config-group-policy)#exit ciscoasa(config)#exit ciscoasa#
Save configuration to non-volatile RAM (NVRAM) and press enter when you are prompted to specify the name of the source file.
Kind regards
Abhishek Purohit
CCIE-S-35269 -
Help blocking smart devices of via VPN
Hello
I am looking for a solution block smart devices to connect to our network via VPN. Our VPN solution today is ASA5520, and we use Cisco ACS to authenticate the user. We use Cisco VPN client only, no anyconnect or SSL VPN.
Managment is looking for a way that we can stop the smart devices of using VPN clients to connect and allow only desktop computers laptops to connect.
Someone at - there a way we can do this through association or another method?
Worring - I block iPhones & iPad around my overall networkwith 100% accuracy with a few simple lines of config: -.
Group Policy <> attributes
client-access-rule 1 deny version of type 'iPhone OS. "
2-client-access rule allow type * version *.
As it actually works on the OS - not the version of the Cisco VPN Client device.
-
How to implement a local SOA/BPM project using remote resources via VPN
Hello world
Sorry for the dummy question, but I am a beginner and I'm in trouble with this problem.
This is the scenario: I have to carry a BPM project using JDev 11.1.1.7 on my local environment and then deploy them on remote servers via VPN where a development environment is configured.
All services are on remote servers.
My question is: what I put up in my local environment?
1 DB connection (distance connettion)
2 configuration of MDS to share components?
3 WebLogic server?
3. what else?
Any link o idea to share?
Thank you.
Fairlie
Hello
If you need to deploy and test in your front room to deploy remotely, then you will need to set up all the people in your premises + SOA Suite... If you need to do is put on your local, but can check remotely, you only JDev and connections...
See you soon,.
Vlad
Maybe you are looking for
-
I was in the middle of Netflix watching when I received an error message: "Silverlight installation problem.Error code: 2103 You have encountered a problem specific to Silverlight from Microsoft, the software used to watch movies on the site Web of N
-
Spooler Sub system stopped working
Hi Forum,I have this message when I try to print. I use Vista Home premium service Pack 1. I print with primoPDF and HP psc1210.It offers to install a printer, but then no, it says that there is a pb with the spooler.Help, pleasePier
-
It happens to someone else? When you zoom in to take a video the reds jumping around?
-
Hello
-
Cannot print after you load the phone with a direct USB cable connection
Original title: fails my. driver what should I do, should I get it fixed or can I do it myself? I was recharging the battery from my phone with my laptop yesterday but I was with the son of a usb cord, but I put the wires in the wrong place on the ch