Access via L2L AnyConnect VPN IPSec

Similar Questions

• Setup for use with Cisco Anyconnect VPN IPsec

  So, I had trouble setting up VPN on our ASA 5510. I would use IPsec VPN so that we don't have to worry about licensing issues, but what I have read you can do with and always use Cisco Anyconnect. My knowledge on how to set up VPN especially in iOS version 8.4 is limited, so I've been using a combination of command line and ASDM.

  I am finally able to connect from a remote location, but once I log in, nothing else works. What I've read, you can use IPsec for client-to-lan connections. I use a pre-shared for this. Documentation is limited on what should happen after have connected you? Shouldn't be able to local access on the vpn connection computers? I'm trying to implement work. If I have VPN from home, should not be able to access all of the resources at work? According to me, because I used the command-line as ASDM I confused some of the configuration. In addition, I think that some of the default policies are confused me too. So I probably need a lot of help. Here is my current setup with the changed IP address and other things that are not related to deleted VPN.

  NOTE: We are still testing this ASA and is not in production.

  Any help you can give me is greatly appreciated.

  ASA Version 8.4 (2)

  !

  ASA host name

  domain.com domain name

  !

  interface Ethernet0/0

  nameif inside

  security-level 100

  the IP 192.168.0.1 255.255.255.0

  !

  interface Ethernet0/1

  nameif outside

  security-level 0

  IP 50.1.1.225 255.255.255.0

  !

  interface Ethernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Management0/0

  No nameif

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  boot system Disk0: / asa842 - k8.bin

  passive FTP mode

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  !

  permit same-security-traffic intra-interface

  !

  network of the NETWORK_OBJ_192.168.0.224_27 object

  subnet 192.168.0.224 255.255.255.224

  !

  object-group service VPN

  ESP service object

  the purpose of the tcp destination eq ssh service

  the purpose of the tcp destination eq https service

  the purpose of the service udp destination eq 443

  the destination eq isakmp udp service object

  !

  allowed IP extended ip access list a whole

  !

  mask 192.168.0.225 - 192.168.0.250 255.255.255.0 IP local pool VPNPool

  no failover

  failover time-out period - 1

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 645.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside, outside) static source any any static destination NETWORK_OBJ_192.168.0.224_27 NETWORK_OBJ_192.168.0.224_27 non-proxy-arp-search to itinerary

  !

  the object of the LAN network

  NAT dynamic interface (indoor, outdoor)

  Access-group outside_in in external interface

  Route outside 0.0.0.0 0.0.0.0 50.1.1.250 1

  Sysopt noproxyarp inside

  Sysopt noproxyarp outdoors

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec ikev2 ipsec-proposal OF

  encryption protocol esp

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 proposal ipsec 3DES

  Esp 3des encryption protocol

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 ipsec-proposal AES

  Esp aes encryption protocol

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 ipsec-proposal AES192

  Protocol esp encryption aes-192

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 AES256 ipsec-proposal

  Protocol esp encryption aes-256

  Esp integrity sha - 1, md5 Protocol

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  registration auto

  name of the object CN = ASA

  Configure CRL

  crypto ca server

  Shutdown

  string encryption ca ASDM_TrustPoint0 certificates

  certificate d2c18c4e

  864886f7 0d06092a c18c4e30 308201f3 3082015c a0030201 d 020204 2 0d 010105

  0500303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609

  02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109

  3131 31303036 31393133 31365a 17 323131 30303331 39313331 0d 170d 6f6d301e

  365a303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609

  02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109

  6f6d3081 9f300d06 092 has 8648 86f70d01 01010500 03818d b 30818902-00-818100-2

  8acbe1f4 5aa19dc5 d3379bf0 f0e1177d 79b2b7cf cc6b4623 d1d97d4c 53c9643b

  37f32caf b13b5205 d24457f2 b5d674cb 399f86d0 e6c3335f 031d54f4 d6ca246c

  234b32b2 b3ad2bf6 e3f824c0 95bada06 f5173ad2 329c28f8 20daaccf 04c 51782

  3ca319d0 d5d415ca 36a9eaff f9a7cf9c f7d5e6cc 5f7a3412 98e71de8 37150f02

  03010001 300 d 0609 2a 864886 f70d0101 05050003 8181009d d2d4228d 381112a 1

  cfd05ec1 0f51a828 0748172e 3ff7b480 26c197f5 fd07dd49 01cd9db6 9152c4dc

  18d0f452 50f5d0f5 4a8279c4 4c1505f9 f5e691cc 59173dd1 7b86de4f 4e804ac6

  beb342d1 f2db1d1f 878bb086 981536cf f4094dbf 36c5371f e1a0db0a 75685bef

  af72e31f a1c4a892 d0acc618 888b53d1 9b 888669 70e398

  quit smoking

  IKEv2 crypto policy 1

  aes-256 encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 10

  aes-192 encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 20

  aes encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 30

  3des encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 40

  the Encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  Crypto ikev2 activate out of service the customer port 443

  Crypto ikev2 access remote trustpoint ASDM_TrustPoint0

  Crypto ikev1 allow outside

  IKEv1 crypto policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 10

  Console timeout 0

  management-access inside

  SSL-trust outside ASDM_TrustPoint0 point

  WebVPN

  allow outside

  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

  AnyConnect image disk0:/anyconnect-linux-2.5.2014-k9.pkg 2

  AnyConnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 3

  profiles of AnyConnect VPN disk0: / devpn.xml

  AnyConnect enable

  tunnel-group-list activate

  internal VPN group policy

  attributes of VPN group policy

  value of server WINS 50.1.1.17 50.1.1.18

  value of 50.1.1.17 DNS server 50.1.1.18

  Ikev1 VPN-tunnel-Protocol, l2tp ipsec ikev2 ssl-client

  digitalextremes.com value by default-field

  WebVPN

  value of AnyConnect VPN type user profiles

  always-on-vpn-profile setting

  privilege of xxxxxxxxx encrypted password username administrator 15

  VPN1 xxxxxxxxx encrypted password username

  VPN Tunnel-group type remote access

  General-attributes of VPN Tunnel-group

  address (inside) VPNPool pool

  address pool VPNPool

  LOCAL authority-server-group

  Group Policy - by default-VPN

  VPN Tunnel-group webvpn-attributes

  enable VPN group-alias

  Group-tunnel VPN ipsec-attributes

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  class-map ips

  corresponds to the IP access list

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  inspect the http

  class ips

  IPS inline help

  class class by default

  Statistical accounting of user

  I would recommend buy AnyConnect Essentials. The cost of the license is nominal - list of US $150 for the 5510. (piece number L-ASA-AC-E-5510 =)

  Meawwhile you can use the Cisco VPN client inherited with IKEv1 IPSec remote access VPN using profiles *.pcf.

  I believe you can also use the client Anyconnect client SSL or DTLS transport access remotely (non-IPsec) without having to buy the license Anyconnect Essentials for your ASA focus.

  As an aside, note that if you want to use AnyConnect Mobile (e.g. for iPhone, iPad, Android, Blackberry etc.clients) you will also get the additional license for it (L-ASA-AC-M-5510 =, also price US $150)

• Blocks VIRTUAL local network access to a tunnel VPN IPSec on WRV200?

  I have two identical WRV200 wireless routers which are connected by a VPN IPSec tunnel.  This goes to my LAN LAN of my parents.  Everything works well.

  But I also have my WRV200 configured for two VLANS.  Vlan1 for my network and secure wireless access.  VLAN2 for a WiFi not secure for customers.

  My problem is that my guest on VLAN2 slips through the VPN devices and access on LAN of my parents.  I'm looking for a way to block to do this.

  I use the version of the software on the two routers (v1.0.39).

  For what it's worth, I know that my receive an IP address in the range 192.168.x.101 DHCP - 199.  I could assign a different range if that helps.  I thought that I could block this beach on the remote router firewall, but I see there is blocking a single IP address at the time, maximum of 8.  Am I missing something?

  Or could I put something weird in the routing tables somewhere to get the IPs guest out of lala land?

  Any suggestions are appreciated.  I can't be the only one in this boat.

  Steve

  Try to check local and remote, vpn under safe group settings if you change the ip address range subnet. Don't include the range of ip addresses of the computers wireless comments so that it will not pass through the vpn tunnel. If there is no ip range option, you must to the subnet of the network in order to control the ip address you want to allow on the vpn tunnel.

• Cisco Anyconnect VPN vs IPSec AnyConnect SSL

  Hello

  Can someone tell me what is the difference between the Anyconnect SSL VPN and Anyconnect VPN IPSec.

  When we use one and not the other?

  Thank you very much.

  Best regards.

  Hello Abdollah,

  AnyConnect based on the SSL protocol is called Anyconnect SSL VPN and if you deploy Anyconnect with the IPSec protocol, it is called IKev2.

  AnyConnect (via IKEv2 or SSLVPN) does not use a pre shared key to authenticate the user.  A certificate will be used to authenticate the user and the ASA of + pass and the certificate used to authenticate the user.  The XML profile is necessary just to use the Anyconnect IKEv2 client rather than the default of SSL when connecting to the ASA.

  Here is the doc announced some of the benefits of using Anyconnect with Ikev2 rather than SSL VPN.
  http://www.Cisco.com/en/us/docs/iOS-XML/iOS/sec_conn_ike2vpn/configuration/15-2mt/sec-cfg-IKEv2-Flex.html#GUID-6548042E-1E4C-416A-8347-00DCF96F04DF

  In essence, if you have a simple deployment, then you can go with the installation of SSL VPN and if you want to take advantage of additional features, you can use Anyconnect with IPSec.

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• Quality of VoIP BOUNCING over AnyConnect VPN problems

  Hello:

  I'm in the middle of the conversion of our environment of VPN for remote access of the former client VPN Cisco AnyConnect (ver. 3.1.01065) VPN's IPSec. I have a number of beta-testers on the new AnyConnect VPN environment, and we have quality problems of intermittent VoIP (IP Communicator 8.5.3 on remote laptops) with the HQ VPN. While I realize that we miss the calls over the Internet, which is a network of 'better' and can not control the Inernet QoS, the special thing is the VoIP call on the former that ipsec VPN seems to work very well 99% of the time.

  I did a series of G.729 calls on the old client IPSec and customer AC, with the same laptop, using the same remote access connection. The "VPN server" for the IPSec VPN is an ASA5520 (8.0 (4)), on a connection of 100 Mbps with plenty of reserve, which runs also firewall services for an office of about 500 people and a small DMZ environment. The VPN server that is handling AnyConnect VPN is a new ASA5515-X (8.6 (1) 2), using the same channel of 100 Mbit/s Internet and running VPN services only. When you call running of tests on the old IPSec VPN, the jitter of appeal is pretty consistent, where jitter ave runs about 10 ms and jitter peak running 30-40ms. On the client ACTS, so that 'good' calls run about the same jitter as the old VPN, called the 'bad' (drops intermittent speaker, sometimes sounds 'mechanized'), which produce about 1 of evey 5 calls, run jitter ave to about 120-150ms and jitter of tip of 300-400 m for info, I don't see no packet loss to talk, just call jitter is through the roof. While in most cases, this could be written off as a "bad Internet connection", on the pretty old VPN tests prove a lot is not the issue.

  That said, anyone has an idea why the quality of calls is sometimes wrong via the AnyConnect VPN? Is there pest practices that I can work from, or any settings you can recommend? Thank you.

  Well, there are several things in our implementation that could help if possible, although I think you can open the case of the TAC, we saw some strange behaviors.

  Things to enable the audit side ASA/SSL:

  -DTLS - check if it is enabled and WORK (see the det filter name NAME_HERE anyconnect vpn-sessiondb)

  see if the packets are tunneled by the DTLS Protocol not TLS. The datagram transport is much better suited for performance.

  -Compression - so we see a lot of deployments with it enabled us say this as much as we can. Compression is for links to bandwidth low latency. In the modern internet, it should be used with caution.

  -check the ASP drop table on ASA (fall of claire asp, run the "show asp drop' rest and during the period of low performance monitor.)

  -additional recording "class... ssl connection. "can give you greater participation.

  -See the proto ssl_np - good starting point count

  the list goes on and.

  What is important to understand, is that the problem is with the traffic on the wire or from the use of SSL.

  Sniffer traces are essential.

  M.

• Redundancy ASA - Client to the remote access (AnyConnect or IPsec) VPN Cisco to 2 PSI

  Hello

  I realize that the true public access redundancy require routers and BGP need &AS#; but some can't afford such a solution.  Should someone have ASA 5510 dry + with 2 of the ISP could use IP SLA functionality for primary education to save the failover, etc..  What VPN clients for remote access (SSL or IPSec).  I'm curious if you have any other solutions/configurations on it to allow either of these customers, AnyConnect or IPsec, to try the primary counterpart and after a few failed attempts over fail to backup (even if a user tries to establish a VPN)?  I know that one of the possible solutions may use a domain name FULL peer IPSec or AnyConnect client input, then maybe public operator DNS TTL change or other hosted / failover services... but these "proxy" or DNS services are not the best solution because there is cache and other associated DNS weaknesses (right)?  These are not infallible fail-over, I'm sure that some users might succeed and some may fail; I do not know administrators will be like that as much as they like going to the dentist.

  Anyone who has any ideas or possible solutions?

  Thank you.

  Hello

  Backup servers are supported by remote access VPN clients.

  The client will attempt to connect to the first IP/configured FULL domain name and will try the following in the list, if no response is received.

  http://www.Cisco.com/en/us/docs/security/vpn_client/cisco_vpn_client/vpn_client46/win/user/guide/VC4.html#wp1000747

  Federico.

• AnyConnect VPN client can be used for IPSec remote access VPN connection?

  I think I heard it somewhere that AnyConnect VPN can be used for connections SSLvpn IPSec VPN. Is this possible? Thank you!

  No, the Anyconnect software cannot be used to establish the framework for a VPN IPSEC IKE.

• no client AnyConnect vpn internet access

  AnyConnect vpn client no internet no access.

  Here is the configuration. Help, please.

  Thank you

  Jessie

  ASA Version 8.2 (1)

  !

  hostname ciscoasa5505

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 172.16.0.1 255.255.0.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address 69.x.x.54 255.255.255.248

  !

  interface Vlan5

  Shutdown

  prior to interface Vlan1

  nameif dmz

  security-level 50

  DHCP IP address

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  passive FTP mode

  DNS lookup field inside

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  Server name 172.16.0.2

  Server name 69.x.x.6

  object-group Protocol TCPUDP

  object-protocol udp

  object-tcp protocol

  object-group service TS-777-tcp - udp

  port-object eq 777

  object-group service Graphon tcp - udp

  port-object eq 491

  object-group service TS-778-tcp - udp

  port-object eq 778

  object-group service moodle tcp - udp

  port-object eq 5801

  object-group service moodle-5801 tcp - udp

  port-object eq 5801

  object-group service 587 smtp tcp - udp

  EQ port 587 object

  outside_access_in list extended access permit tcp any host 69.x.x.50 eq imap4

  outside_access_in list extended access permit tcp any host 69.x.x.52 eq ftp

  outside_access_in list extended access allowed object-group TCPUDP any object-group of 69.x.x.50 host smtp-587

  outside_access_in list extended access permit tcp any host 69.x.x.52 eq telnet

  outside_access_in list extended access permit tcp any host 69.x.x.52 eq ssh

  outside_access_in list extended access allowed object-group TCPUDP any host object-group moodle-5801 69.x.x.52

  outside_access_in list extended access permit tcp any host 69.x.x.52 eq smtp

  outside_access_in list extended access permit tcp any host 69.x.x.52 eq https

  outside_access_in list extended access permit tcp any host 69.x.x.52 eq www

  outside_access_in list extended access permit tcp any host 69.x.x.50 eq ftp

  outside_access_in list extended access permit tcp any host 69.x.x.50 eq smtp

  outside_access_in list extended access permit tcp any host 69.x.x.50 eq pop3

  outside_access_in list extended access allowed object-group TCPUDP any host 69.x.x.50 EQ field

  outside_access_in list extended access permit tcp any host 69.x.x.50 eq https

  outside_access_in list extended access permit tcp any host 69.x.x.50 eq www

  outside_access_in list extended access allowed object-group TCPUDP any host 69.x.x.51 EQ field

  outside_access_in list extended access allowed object-group TCPUDP any host TS-778 69.x.x.51 object-group

  outside_access_in list extended access allowed object-group TCPUDP any host Graphon 69.x.x.51 object-group

  outside_access_in list extended access permit tcp any host 69.x.x.51 eq https

  outside_access_in list extended access permit tcp any host 69.x.x.51 eq www

  outside_access_in list extended access allowed object-group TCPUDP any host TS-777 69.x.x.50 object-group

  outside_access_in list extended access permit tcp any host 69.x.x.54 eq https

  access extensive list ip 172.16.0.0 outside_cryptomap_1 allow 255.255.0.0 192.168.50.0 255.255.255.0

  access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.0.0 192.168.0.0 255.255.255.0

  inside_nat0_outbound list of allowed ip extended access all 172.16.0.32 255.255.255.224

  access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.0.0 192.168.50.0 255.255.255.0

  access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.0.0 192.168.1.0 255.255.255.0

  inside_access_in of access allowed any ip an extended list

  Standard Split-Tunnel access list permit 172.16.0.0 255.255.0.0

  access-list SHEEP extended ip 172.16.0.0 allow 255.255.0.0 192.168.0.0 255.255.255.0

  access-list SHEEP extended ip 172.16.0.0 allow 255.255.0.0 192.168.50.0 255.255.255.0

  access-list SHEEP extended ip 172.16.0.0 allow 255.255.0.0 192.168.1.0 255.255.255.0

  access-list SHEEP extended ip 172.16.0.0 allow 255.255.0.0 172.16.0.0 255.255.0.0

  access extensive list ip 172.16.0.0 outside_cryptomap allow 255.255.0.0 192.168.0.0 255.255.255.0

  access extensive list ip 172.16.0.0 outside_cryptomap_2 allow 255.255.0.0 192.168.1.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  MTU 1500 dmz

  IP local pool VPN_Users 172.16.100.10 - 172.16.100.20 mask 255.255.255.0

  IP local pool anypool 172.16.0.9 - 172.16.0.19 mask 255.255.0.0

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0 access-list SHEEP

  NAT (inside) 1 0.0.0.0 0.0.0.0

  public static 69.x.x.50 (Interior, exterior) 172.16.0.2 netmask 255.255.255.255

  public static 69.x.x.51 (Interior, exterior) 172.16.1.2 netmask 255.255.255.255

  public static 69.x.x.52 (Interior, exterior) 172.16.1.3 netmask 255.255.255.255

  inside_access_in access to the interface inside group

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 69.x.x.49 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  Enable http server

  http 172.16.0.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  card crypto outside_map 1 match address outside_cryptomap

  card crypto outside_map 1 set pfs

  card crypto outside_map 1 set 208.x.x.162 counterpart

  card crypto outside_map 1 set of transformation-ESP-3DES-SHA

  card crypto outside_map 2 match address outside_cryptomap_1

  card crypto outside_map 2 set pfs

  card crypto outside_map 2 peers set 209.x.x.178

  card crypto outside_map 2 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  card crypto outside_map 3 match address outside_cryptomap_2

  card crypto outside_map 3 set pfs

  card crypto outside_map 3 peers set 208.x.x.165

  card crypto outside_map 3 game of transformation-ESP-3DES-SHA

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 5

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 30

  preshared authentication

  3des encryption

  sha hash

  Group 1

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd outside auto_config

  !

  dhcpd address 172.16.0.20 - 172.16.0.40 inside

  dhcpd dns 172.16.0.2 69.x.x.6 interface inside

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow outside

  SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image

  enable SVC

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  Server DNS 172.16.0.2 value

  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

  Group Policy inside sales

  Group sales-policy attributes

  value of server DNS 172.16.1.2 172.16.0.2

  VPN-tunnel-Protocol svc

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value split Tunnel

  WebVPN

  SVC mtu 1406

  internal group anyconnect strategy

  attributes of the strategy group anyconnect

  VPN-tunnel-Protocol svc webvpn

  WebVPN

  list of URLS no

  SVC request to enable default webvpn

  username of graciela CdnZ0hm9o72q6Ddj encrypted password

  graciela username attributes

  VPN-group-policy DfltGrpPolicy

  tunnel-group 208.x.x.165 type ipsec-l2l

  208.x.x.165 group of tunnel ipsec-attributes

  pre-shared-key *.

  tunnel-group AnyConnect type remote access

  tunnel-group AnyConnect General attributes

  address anypool pool

  strategy-group-by default anyconnect

  tunnel-group AnyConnect webvpn-attributes

  Group-alias anyconnect enable

  allow group-url https://69.x.x.54/anyconnect

  tunnel-group 208.x.x.162 type ipsec-l2l

  208.x.x.162 tunnel ipsec-attributes group

  pre-shared-key *.

  tunnel-group 209.x.x.178 type ipsec-l2l

  209.x.x.178 group of tunnel ipsec-attributes

  pre-shared-key *.

  !

  Global class-card class

  match default-inspection-traffic

  !

  !

  World-Policy policy-map

  Global category

  inspect the icmp

  !

  service-policy-international policy global

  context of prompt hostname

  : end

  Hello

  You could start by adding the following configurations

  permit same-security-traffic intra-interface

  This will allow traffic to the VPN users access the interface ' outside ' of the SAA and to leave to the Internet using the same interface ' outside '. Without the above command, it is not possible.

  Also, you need to add a NAT configuration for VPN Client users can use the Internet connection of the ASA

  To do this, you can add this command

  NAT (outside) 1 172.16.0.0 255.255.0.0

  This will allow the PAT for the Pool of VPN dynamics.

  Hope this helps

  Don't forget to mark the reply as the answer if it answered your question.

  Ask more if necessary

  -Jouni

• AnyConnect VPN full tunnel could not access the site to site VPN

  I have a set of AnyConnect VPN upward with no split tunneling (U-turning/crossed traffic), running 8.2.5 code.

  It works fine, but I want to allow customers to AnyConnect VPN site to site, which I was unable to access.

  I checked the IP addresses of network anyconnect are part of the tunnel on both sides.

  My logic tells me that I must not turn back traffic from the network anyconnect for the site to site VPN, but I don't know how to do this.

  Any help would be appreciated.

  Here are the relevant parts of my config:

  (Domestic network is 192.168.0.0/24,

  the AnyConnect network is 192.168.10.0/24,

  site to site VPN network is 192.168.2.0/24)

  --------------------------------------------------------------------------------------

  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface

  the DM_INLINE_NETWORK_1 object-group network
  object-network 192.168.0.0 255.255.255.0
  object-network 192.168.10.0 255.255.255.0
  inside_nat0_outbound list extended access allowed object-group ip DM_INLINE_NETWORK_1 192.168.2.0 255.255.255.0
  permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.10.0 255.255.255.0

  outside_1_cryptomap list extended access allowed object-group ip DM_INLINE_NETWORK_1 192.168.2.0 255.255.255.0

  mask 192.168.10.2 - 192.168.10.254 255.255.255.0 IP local pool AnyConnectPool
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0_outbound
  NAT (inside) 1 0.0.0.0 0.0.0.0
  NAT (outside) 1 192.168.10.0 255.255.255.0
  access-outside group access component software snap-in interface outside
  Route outside 0.0.0.0 0.0.0.0 (the gateway IP) 1
  WebVPN
  allow outside
  AnyConnect essentials
  SVC disk0:/anyconnect-win-3.1.05152-k9.pkg 1 image
  SVC profiles AnyConnectProfile disk0: / anyconnect_client.xml
  enable SVC
  tunnel-group-list activate
  internal AnyConnectGrpPolicy group strategy
  attributes of Group Policy AnyConnectGrpPolicy
  WINS server no
  value of 192.168.0.33 DNS server 192.168.2.33
  VPN-session-timeout no
  Protocol-tunnel-VPN l2tp ipsec svc
  Split-tunnel-policy tunnelall
  the address value AnyConnectPool pools
  type tunnel-group AnyConnectGroup remote access
  attributes global-tunnel-group AnyConnectGroup
  address pool AnyConnectPool
  authentication-server-group SERVER1_AD
  Group Policy - by default-AnyConnectGrpPolicy
  tunnel-group AnyConnectGroup webvpn-attributes
  the aaa authentication certificate
  activation of the Group _AnyConnect alias

  Your dial-up VPN traffic as originating apears on the external interface, so I think you need to exonerate NAT pool PN traffic directed to the site to site VPN. Something like this:

   global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 nat (outside) 0 access-list outside_nat0 nat (outside) 1 192.168.10.0 255.255.255.0 access-list outside_nat0 extended permit ip any 192.168.10.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip 192.168.0.0 255.255.255.0 192.168.10.0 255.255.255.0

• AnyConnect VPN is not access to the ASA

  Hello

  I have an ASA 5512 - x configured as a hub AnyConnect VPN, but when I connect I can not access the firewall... I can ping the address 10.4.11.2 but I can not connect... No idea what to do? It's the running configuration:

  : Saved

  :

  ASA 1.0000 Version 2

  !

  asa-oi hostname

  domain xx.xx.xx.xx

  activate 7Hb0WWuK1NRtRaEy encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  1.1.1.1 DefaultGW-outside name description default gateway outside

  name 10.4.11.1 description DefaultGW - Default Gateway inside Inside

  !

  interface GigabitEthernet0/0

  nameif inside

  security-level 100

  IP 10.4.11.2 255.255.255.0

  !

  interface GigabitEthernet0/5

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/5.2000

  VLAN 2000

  nameif outside

  security-level 0

  IP 1.1.1.2 255.255.255.252

  !

  interface Management0/0

  Shutdown

  No nameif

  no level of security

  no ip address

  management only

  !

  boot system Disk0: / asa861-2-smp - k8.bin

  passive FTP mode

  clock timezone BRST-3

  clock summer-time recurring BRDT 2 Sun Oct 0:00 Sun Feb 3 0:00

  DNS lookup field inside

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  1.1.1.1 server name

  1.1.1.2 server name

  domain xx.xx.xx.xx

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  network of the PoolAnyConnect object

  subnet 10.6.4.0 255.255.252.0

  access extensive list permits all ip a outside_in

  list of access by standard tunnel allowed 10.0.0.0 255.0.0.0

  pager lines 24

  Enable logging

  timestamp of the record

  exploitation forest-size of the buffer 1048576

  logging buffered information

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  mask 10.6.4.1 - 10.6.7.254 255.255.252.0 IP local pool PoolAnyConnect

  ICMP unreachable rate-limit 1 burst-size 1

  ICMP allow any inside

  ICMP allow all outside

  ASDM image disk0: / asdm - 66114.bin

  enable ASDM history

  ARP timeout 14400

  NAT (inside, outside) static source any any static destination PoolAnyConnect PoolAnyConnect non-proxy-arp-search to itinerary

  NAT (exterior, Interior) static source PoolAnyConnect PoolAnyConnect non-proxy-arp-search to itinerary

  Access-group outside_in in external interface

  Route outside 0.0.0.0 0.0.0.0 DefaultGW-outdoor 1

  Route inside 10.0.0.0 255.0.0.0 DefaultGW-Inside 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA-Server LDAP protocol ldap

  AAA-server host 3.3.3.3 LDAP (inside)

  Timeout 5

  LDAP-base-dn o = xx

  LDAP-scope subtree

  LDAP-naming-attribute sAMAccountName

  novell server type

  identity of the user by default-domain LOCAL

  the ssh LOCAL console AAA authentication

  AAA authentication enable LOCAL console

  AAA authentication http LOCAL console

  Enable http server

  http 0.0.0.0 0.0.0.0 inside

  http 2.2.2.2 255.255.255.240 outside

  Telnet timeout 5

  SSH 0.0.0.0 0.0.0.0 inside

  SSH 2.2.2.2 255.255.255.240 outside

  SSH timeout 10

  Console timeout 10

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  SSL cipher aes128-sha1 aes256-3des-sha1 sha1

  WebVPN

  allow outside

  AnyConnect essentials

  AnyConnect image disk0:/anyconnect-win-3.1.03103-k9.pkg 1

  AnyConnect enable

  tunnel-group-list activate

  internal GrpPolicyAnyConnect group strategy

  attributes of Group Policy GrpPolicyAnyConnect

  value of server DNS 1.1.1.1 1.1.1.2

  VPN - 1000 simultaneous connections

  client ssl-VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value in tunnel

  field default value xx.xx.xx.xx

  admin Dp4l7Cmqr7SMHl.l encrypted privilege 15 password username

  tunnel-group AnyConnect type remote access

  tunnel-group AnyConnect General attributes

  address pool PoolAnyConnect

  LDAP authentication group-server

  Group Policy - by default-GrpPolicyAnyConnect

  tunnel-group AnyConnect webvpn-attributes

  enable AnyConnect group-alias

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  inspect the ctiqbe

  inspect the http

  inspect the dcerpc

  inspect the dns

  inspect the icmp

  inspect the icmp error

  inspect the they

  inspect the amp-ipsec

  inspect the mgcp

  inspect the pptp

  inspect the snmp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:9399e42e238b5824eebaa115c93ad924

  : end

  BTW, I changed the NAT configuration many attempts the problem, this is the current...

  YPU need to allow your client VPN address pool (10.6.4.1 mask - 10.6.7.254 255.255.252.0) ssh and http from 'outside' access, which is where they come from. Add them to the:

  http 0.0.0.0 0.0.0.0 inside

  http 2.2.2.2 255.255.255.240 outside

  SSH 0.0.0.0 0.0.0.0 inside

  SSH 2.2.2.2 255.255.255.240 outside

• Press L2L VPN, IPSEC, and L2TP PIX connections

  Hi all

  I'm trying to implement a solution on my FW PIX (pix804 - 24.bin) to be able to support a VPN L2L session with VPN dynamic user sessions where clients will use a mix of IPSEC(Nat detection) and L2TP. We have always supported things IPSEC and that worked great for many years. I'm now trying to Add L2TP support, so that I can support Android phones/ipads, etc. as well as Windows with built in VPN l2tp clients clients. Everything works well except for the new features of L2TP. Allows you to complete one phase but then tries to use the card encryption that is used for the VPN L2L. It seems to fail because IP addresses are not in the configured ACL to the crypto-map L2L. Does anyone know if there are any questions all these configurations support both. And if not can you see what I have wrong here, which would make it not work. Here are the relevant training:

  C515 - A # sh run crypto
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set of society-ras-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set esp-3des esp-sha-hmac company-l2tp
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Dynamic crypto map company-ras 1 correspondence address company-dynamic
  company Dynamics-card crypto-ras 1 set pfs
  Dynamic crypto map company-ras 1 transform-set ESP-SHA-3DES ESP-3DES-MD5 company-ras
  Dynamic crypto map company-ras 1 lifetime of security association set seconds 28800
  company Dynamics-card crypto-ras 1 kilobytes of life together - the association of safety 4608000
  crypto dynamic-map-ras company 2 address company-dynamic game
  crypto dynamic-map company-ras 2 transform-set of society-l2tp
  crypto dynamic-map company-ras 2 set security association lifetime seconds 28800
  company Dynamics-card crypto-ras 2 kilobytes of life together - the association of safety 4608000
  card crypto company-map 1 correspondence address company-colo
  card crypto company-card 1 set pfs
  card crypto company-card 1 set counterpart colo-pix-ext
  card crypto card company 1 value transform-set ESP-3DES-MD5 SHA-ESP-3DES
  company-map 1 lifetime of security association set seconds 28800 crypto
  card company-card 1 set security-association life crypto kilobytes 4608000
  company-card 1 set nat-t-disable crypto card
  company-card 2 card crypto ipsec-isakmp dynamic company-ras
  business-card interface card crypto outside
  crypto isakmp identity address
  crypto ISAKMP allow outside

  Crypto isakmp nat-traversal 3600

  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 2
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400
  C515 - A # sh run tunnel-group
  attributes global-tunnel-group DefaultRAGroup
  company-ras address pool
  Group-LOCAL radius authentication server
  Group Policy - by default-l2tp
  IPSec-attributes tunnel-group DefaultRAGroup
  pre-shared-key *.
  tunnel-group DefaultRAGroup ppp-attributes
  PAP Authentication
  No chap authentication
  ms-chap-v2 authentication
  eap-proxy authentication
  type tunnel-group company-ras remote access
  tunnel-group global company-ras-attributes
  company-ras address pool
  Group-LOCAL radius authentication server
  tunnel-group company-ras ipsec-attributes
  pre-shared-key *.
  type tunnel-group company-admin remote access
  attributes global-tunnel-group company-admin
  company-admin address pool
  Group-LOCAL radius authentication server
  company strategy-group-by default-admin
  IPSec-attributes of tunnel-group company-admin
  pre-shared-key *.
  PPP-attributes of tunnel-group company-admin
  No chap authentication
  ms-chap-v2 authentication
  tunnel-group x.x.x.x type ipsec-l2l
  tunnel-group ipsec-attributes x.x.x.x
  pre-shared-key *.
  ISAKMP keepalive retry threshold 15 10
  C515 - A # sh run Group Policy
  attributes of Group Policy DfltGrpPolicy
  Server DNS 10.10.10.20 value 10.10.10.21
  Protocol-tunnel-VPN IPSec
  enable PFS
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value company-SPLIT-TUNNEL-ACL
  company.int value by default-field
  NAC-parameters DfltGrpPolicy-NAC-framework-create value
  internal strategy of company-admin group
  attributes of the strategy of company-admin group
  WINS server no
  DHCP-network-scope no
  VPN-access-hour no
  VPN - 20 simultaneous connections
  VPN-idle-timeout 30
  VPN-session-timeout no
  Protocol-tunnel-VPN IPSec l2tp ipsec
  disable the IP-comp
  Re-xauth disable
  Group-lock no
  enable PFS
  Split-tunnel-network-list value company-ADMIN-SPLIT-TUNNEL-ACL
  L2TP strategy of Group internal
  Group l2tp policy attributes
  Server DNS 10.10.10.20 value 10.10.10.21
  Protocol-tunnel-VPN l2tp ipsec
  disable the PFS
  Split-tunnel-policy tunnelall
  company.int value by default-field
  NAC-parameters DfltGrpPolicy-NAC-framework-create value

  Relevant debug output

  C515 - Has # Sep 03 02:09:33 [IKEv1 DEBUG]: IP = 66.25.14.195, Oakley proposal is acceptable
  Sep 03 02:09:33 [IKEv1 DEBUG]: IP = 66.25.14.195, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false
  Sep 03 02:09:33 [IKEv1 DEBUG]: IP = 66.25.14.195, IKE SA proposal # 1, turn # 1 entry IKE acceptable Matches # 3 overall
  Sep 03 02:09:33 [IKEv1]: IP = 66.25.14.195, connection landed on tunnel_group DefaultRAGroup
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, status of automatic NAT detection: remote endpoint IS behind a NAT device this end is NOT behind a NAT device
  Sep 03 02:09:33 [IKEv1]: IP = 66.25.14.195, connection landed on tunnel_group DefaultRAGroup
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, previously allocated memory of liberation for permission-dn-attributes
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, PHASE 1 COMPLETED
  Sep 03 02:09:33 [IKEv1]: IP = 66.25.14.195, for this connection Keep-alive type: None
  Sep 03 02:09:33 [IKEv1]: IP = 66.25.14.195, Keep-alives configured on, but the peer does not support persistent (type = None)
  Sep 03 02:09:33 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 66.25.14.195, timer to generate a new key to start P1: 21600 seconds.
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID remote Proxy Host: address 172.16.0.104 17 of the Protocol, Port 0
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID local Proxy Host: address x.x.x.x, 17 of the Protocol, Port 1701
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, detected L2TP/IPSec session.
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, QM IsRekeyed its not found old addr
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto, check card company card, seq = 1 =...
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto card = company-map, seq = 1, ACL does not proxy IDs src:66.25.14.195 dst: x.x.x.x
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, tunnel IPSec rejecting: no entry for crypto for proxy card proxy remote 66.25.14.195/255.255.255.255/17/0 local x.x.x.x/255.255.255.255/17/1701 on the outside interface
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, error QM WSF (P2 struct & 0x501c1f0, mess id 0xa181b866).
  Sep 03 02:09:33 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 66.25.14.195, case of mistaken IKE responder QM WSF (struct & 0x501c1f0) , : QM_DONE EV_ERROR--> QM_BLD_MSG2 EV_NEGO_SA--> QM_BLD_MSG2, EV_IS_REKEY--> QM_BLD_MSG2, EV_CONFIRM_SA--> QM_BLD_MSG2, EV_PROC_MSG--> QM_BLD_MSG2, EV_HASH_OK--> QM_BLD_MSG2, NullEvent--> QM_BLD_MSG2, EV_COMP_HASH
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, peer table correlator Removing failed, no match!
  Sep 03 02:09:33 [IKEv1]: ignoring msg SA brand with Iddm 204910592 dead because ITS removal
  Sep 03 02:10:05 [IKEv1 DEBUG]: IP = 66.25.14.195, Oakley proposal is acceptable
  Sep 03 02:10:05 [IKEv1 DEBUG]: IP = 66.25.14.195, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false
  Sep 03 02:10:05 [IKEv1 DEBUG]: IP = 66.25.14.195, IKE SA proposal # 1, turn # 1 entry IKE acceptable Matches # 3 overall
  Sep 03 02:10:05 [IKEv1]: IP = 66.25.14.195, connection landed on tunnel_group DefaultRAGroup
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, status of automatic NAT detection: remote endpoint IS behind a NAT device this end is NOT behind a NAT device
  Sep 03 02:10:05 [IKEv1]: IP = 66.25.14.195, connection landed on tunnel_group DefaultRAGroup
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, previously allocated memory of liberation for permission-dn-attributes
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, PHASE 1 COMPLETED
  Sep 03 02:10:05 [IKEv1]: IP = 66.25.14.195, for this connection Keep-alive type: None
  Sep 03 02:10:05 [IKEv1]: IP = 66.25.14.195, Keep-alives configured on, but the peer does not support persistent (type = None)
  Sep 03 02:10:05 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 66.25.14.195, timer to generate a new key to start P1: 21600 seconds.
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID remote Proxy Host: address 172.16.0.104 17 of the Protocol, Port 0
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID local Proxy Host: address x.x.x.x, 17 of the Protocol, Port 1701
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, detected L2TP/IPSec session.
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, QM IsRekeyed its not found old addr
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto, check card company card, seq = 1 =...
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto card = company-map, seq = 1, ACL does not proxy IDs src:66.25.14.195 dst: x.x.x.x
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, tunnel IPSec rejecting: no entry for crypto for proxy card proxy remote 66.25.14.195/255.255.255.255/17/0 local x.x.x.x/255.255.255.255/17/1701 on the outside interface
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, error QM WSF (P2 struct & 0x501c1f0, mess id 0xa5db9562).
  Sep 03 02:10:05 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 66.25.14.195, case of mistaken IKE responder QM WSF (struct & 0x501c1f0) , : QM_DONE EV_ERROR--> QM_BLD_MSG2 EV_NEGO_SA--> QM_BLD_MSG2, EV_IS_REKEY--> QM_BLD_MSG2, EV_CONFIRM_SA--> QM_BLD_MSG2, EV_PROC_MSG--> QM_BLD_MSG2, EV_HASH_OK--> QM_BLD_MSG2, NullEvent--> QM_BLD_MSG2, EV_COMP_HASH
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, peer table correlator Removing failed, no match!
  Sep 03 02:10:05 [IKEv1]: ignoring msg SA brand with Iddm 204914688 dead because ITS removal

  The outputs of two debugging who worry are the following:

  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID remote Proxy Host: address 172.16.0.104 17 of the Protocol, Port 0
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID local Proxy Host: address x.x.x.x, 17 of the Protocol, Port 1701

  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto, check card company card, seq = 1 =...
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto card = company-map, seq = 1, ACL does not proxy IDs src:66.25.14.195 dst: x.x.x.x
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, tunnel IPSec rejecting: no entry for crypto for proxy card proxy remote 66.25.14.195/255.255.255.255/17/0 local x.x.x.x/255.255.255.255/17/1701 on the outside interface
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, error QM WSF (P2 struct & 0x501c1f0, mess id 0xa5db9562).

  This seems to indicate that his NAT detection but then do not assign to the entry card cryptography because networks are encrypted are not in the configured ACL that is true. He needs to use dynamic input and it doesn't seem to be.

  I need to create another dynamic map entry to make it work instead of add lines to the same dynamic with a lower (higher) priority map entry?

  Thanks in advance for any help here.

  Hello

  That won't do the trick, l2tp clients are picky kindda, so you know if they do not hit the correct strategy first they just stop trying. Follow these steps:

  correspondence from the company of dynamic-map crypto-ras 1 address company-dynamic

  No crypto-card set pfs dynamic company-ras 1

  No crypto dynamic-map company-ras-1 transform-set ESP-SHA-3DES ESP-3DES-MD5 company-ras

  Dynamic crypto map company-ras 1 transform-set company-l2tp SHA-ESP-3DES ESP-3DES-MD5 company-ras

  The foregoing will not affect existing customers of IPsec at all, these clients will not use the statement of pfs and will link even if the correspondence address is not configured (it is optional), besides Cisco IPsec clients will be affected first the mode of transport policy and fail however they will continue to try and hit another police PH2.

  Regarding your last question, I was referring specifically to the support of l2tp for android, and Yes, you will need to run one of these versions.

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/release/notes/asarn82.html#wp431562

  Tavo-

• Routing access to Internet through an IPSec VPN Tunnel

  Hello

  I installed a VPN IPSec tunnel for a friend's business. At his desk at home, I installed a Cisco SA520 and at it is remote from the site I have a Cisco RVS4000. The IPSec VPN tunnel works very well. The remote site, it can hit all of its workstations and peripheral. I configured the RVS4000 working in router mode as opposed to the bridge. In the Home Office subnet is 192.168.1.0/24 while the subnet to the remote site is 192.168.2.0/24. The SA520 is configured as Internet gateway for the headquarters to 192.168.1.1. The remote desktop has a gateway 192.168.2.1.

  I need to configure the remote site so that all Internet traffic will be routed via the Home Office. I have to make sure that whatever it is plugged into the Ethernet on the RVS4000 port will have its Internet traffic routed through the Internet connection on the SA520. Currently I can ping any device on the headquarters of the remote desktop, but I can't ping anything beyond the gateway (192.168.1.1) in the Home Office.

  Any help would be greatly appreciated.

  Thank you.

  Hi William, the rvs4000 does not support the tunnel or esp transfer wild-card.

• VPN - IPSec remote access

  Hi community support.

  I have an ASA with double tis (gig0/0-gig0/1) and gig0/1 has a default route with admin distance from 254 to back it up.

  I just created Cisco Anyconnect on the SAA the wizard and I can connect to both interfaces.

  IPSec tunnel configuration is also there and I tried to create an IPSec VPN entry on the with my iPhone and I can connect to gig0/0 or gig0/1 if gig0/0 is stopped.  But I can not connect to gig0/1 if gig0/0 is in place.

  When I run ' isa crypto to show his ", I get the following error:

  ciscoasa # show crypto isa his

  IKEv1 SAs:

  ITS enabled: 1
  Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
  Total SA IKE: 1

  1 peer IKE: X.X.X.X
  Type: user role: answering machine
  Generate a new key: no State: AM_WAIT_MSG3

  So the question is, is that what it means and why it works if I close gig0/0 (which is the main interface) and would be why Cisco Anyconnect works also with two interfaces up and customer VPN Cisco Legacy does not work?

  Thank you

  Hello

  What is expected due to the way table routing of the SAA is currently designed. ASA supports not only routing table overall but the routing by interface table as well.

  In the case of IPSec VPN, ASA-control path will do a search of route for the response packet. This search returns the interface of ISP outside/primaries as the best route, but because you tried to connect to the backup, ASA will drop the packet.

  In the case of Anyconnect VPN or SSH/Telnet, ASA creates a connection to flow forward and reversed to the original application flow and does not pass through the route search mechanism and uses only the output interface (where the request has been received) to send the response. AnyConnect session will follow the routing of each interface table.

  Check it for your reference: -.
  https://BST.cloudapps.Cisco.com/bugsearch/bug/CSCsg39338/?reffering_site=dumpcr

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• AnyConnect VPN and LAN access

  When remote users to connect to the Cisco ASA VPN and authenticate with Cisco AnyConnect client, they then full access to the environment internal of LAN of business as if they were sitting at their desks in the Office of the Corporation.

  Right?

  After that the remote client authenticates to the AnyConnect VPN, it is sensible to then run remote users of traffic through the corporate firewall (outside to inside) before allowing LAN access full corporate?

  Remote_User - vpn - ANYCONNECT-(outside) (inside) firewall - CORP_LAN

  Thank you

  Frank

  Hello

  Yes, by default, all traffic will be sent through the tunnel.

  If there are users VPN shouldn't be able to reach the resources, you need to establish rules for access to it. The best way to do this is by using VPN filter.

• Lock the AnyConnect VPN with broader access list

  I'm trying to lock my AnyConnect VPN interface. I use the split tunneling. I want only to http tunnel traffic to an external http server we have and ftp to another external server behave. I don't want anything else through the tunnel or anywhere else allowed on our network. My current setup, I can connect to the vpn and the servers ping external ip address, but not by name. I can also not navigate anywhere else while I'm connected. It is not imperative for me to navigate anywhere else, when you are connected, but I need to allow only access specified above.

  Configuration:

  attributes Anyconnect-group policy

  VPN-tunnel-Protocol svc webvpn

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list WebAccessVPN

  WebVPN

  list of URLS no

  SVC request to enable default webvpn

  WebAccessVPN list extended access allow icmp disable any newspaper host FTP - EXT object-group Ping_and_Trace

  External FTP FTP access WebAccessVPN-list comment

  WebAccessVPN list extended access permitted tcp disable no matter what newspaper to host FTP - EXT object-group DM_INLINE_TCP_2

  WebAccessVPN list extended access allow icmp disable any newspaper host LICENSING-EXT object-group Ping_and_Trace

  WebAccessVPN list extended access allowed object-group TCPUDP any LICENSING-EXT eq www log disable host

  WebAccessVPN list extended access deny ip any object-group DM_INLINE_NETWORK_1

  You can use the vpn filter under the attributes of political group. In the vpn-filter, you can reference the access list you created.