Aurora-R4 upgrade issues & troubleshooting

Similar Questions

• The iTunes upgrade issue in early 2015 does not not on OS 10.6.8. How I found an earlier version of iTunes.

  The iTunes upgrade issue in early 2015 does not not on OS 10.6.8. How I found an earlier version of iTunes?

  General search for versions of iTunes available - http://support.apple.com/downloads/#itunes

  Note: Running an old version won't sync with a device iOS9. The only way to do is run a new version of the OS.

• Rams of upgrade issues for Alienware Aurora R3

  I have an Alienware R3 with 8 GB of ram 1333 MHz! I can it switch to 16 GB of ram 1600 MHz? If Yes, then which is the good rams for this situation?

  The Aurora R3 system uses 1333 MHz, 1600 MHz XMP and 1866 MHz DDR3 XMP of unbuffered SDRAM.
  And the CAP for the RAM is indeed 16 GB.
  Personally, I recommend this one.

• Aurora-R4, upgrade from Windows 7 to Windows 8.1?

  Hi all

  I have a R4 Aurora bought June 2014 that came with Windows 7. Now, I got a license of 8.1 and want to update. I've seen a few posts showing troubleshooting when you upgrade. Can someone tell me if I can perform a new installation or I can't? Is there something I'm doing before the upgrade? I would like to have all the applications from dell that came pre-installed in my Windows 7 such Alienware Command Center, etc...

  Any help will be much appreciated. Thank you much in advance.

  Better to save your data and clean install Win8, Win8 certified drivers from support.dell.com site followed. Go to Aurora R4 and select Win8 as operating system. Towards the end, you will install the compatible version of Win8's Command Center.

  What other Dell applications do you or really need? I can't think at all. In any case... they will be older versions of Win7. Best just to move and replace them if necessary. Yes, which?

  Edit: Here are some useful links:

  http://www.Dell.com/support/article/us/en/19/536193?c=us&s=DHS&CS=19&l=

  http://en.community.Dell.com/Owners-Club/Alienware/f/3746/t/19376654

• Aurora-R4, upgrade CPU

  I plan to upgrade the processor of my Alienware AURORA R4 with BIOS upgrade to A - 11.

  That's what I have now:

  CPU - Intel Core i7 3960 X 3.30 GHz

  Socket LGA 2011

  Mainboard - Alienware 07JNH0

  Chipset - Intel Sandy Bridge-E

  OS - Windows 10 (x 64)

  Please, can someone tell my which is the highest CPU whithin this kind I should hold account?

  Thank you very much

  These were all the valid Dell processors for the Aurora-R4 = 2012
  972H 5 SandyBridge i3-2120, 65w, 3.30 GHz
  F44M4, 0TGM7 SandyBridge 3820 i7 four Core, 130w, 3.60 GHz up to 4.20 GHz
  9R2W8, 2T0RC SandyBridge i7 - 3930K Six Core, 130w, 3.20 GHz up to 4.20 GHz
  VYNF8 SandyBridge i7-3960 Six Core, 130w, 3.33 GHz
  705VT Ivybridge E i7 - 4820K Six Core, 130w, 3.70 GHz up to 3.90 GHZ
  0158V Ivybridge E i7 - 4930K Six Core, 130w, and 3,40 GHz up to 4,10 GHz
  07VY9 Ivybridge E i7-4960 X Six Core, 130w, 3.60 GHz up to 4.30 GHz

• The GPU with Aurora r3 upgrade

  Hello

  So I have an alienware aurora r3 with a gtx 460 and I would like to upgrade. The card, to which I would like to upgrade is a 770 4 GB evga gtx edition. Is it possible for me to move on this card, and how will I know if I have the PSU 875w? The CPU is an I5 2400 with 8 GB of ram and the parent stock. Thanks in advance.

  Capricious, machine bit the Aurora-R3. Buy card retailer with possibility of return.

  User seems to have a bit more luck with AMD nVidia to update video card of spare parts on this machine.

  http://en.community.Dell.com/Owners-Club/Alienware/f/3746/t/19524942.aspx

• Issue troubleshooting, driver and keyboard.

  Hello I troubleshoot-made my Windows 8, detected these issues as follows. Miniport (Network Monitor) Wan #2 has a driver problem Miniport (Network Monitor) Wan #2 has a driver problem There is a problem with the wide AREA network (Network Monitor) #2 Miniport driver. The driver must be reinstalled.
  Reinstall the device driver Completed
  Problem with the PnP devices Problem with the PnP devices There are problems with some devices PnP. Windows will take additional steps to continue troubleshooting these devices.	Detected

  Update of Windows configured to never install drivers Update of Windows configured to never install drivers The driver updates are not installed automatically when detected by Windows Update.

  There is no question

  Problems found	Details of detection
  6 Miniport (Network Monitor) Wan #2 has a driver problem Not fixed
  There is a problem with the wide AREA network (Network Monitor) #2 Miniport driver. The driver must be reinstalled.

  
  The device information

  Name:	Miniport (Network Monitor) Wan #2
  ID:	ROOT\MS_NDISWANBH\0001
  Error code:	31

  Reinstall the device driver Completed

  There is a problem with the wide AREA network (Network Monitor) #2 Miniport driver. Reinstall the driver may resolve this issue.

  Problem with the PnP devices Detected
  There are problems with some devices PnP. Windows will take additional steps to continue troubleshooting these devices.
  Potential problems that have been verified	Details of detection

  Update of Windows configured to never install drivers There is no question

  The driver updates are not installed automatically when detected by Windows Update.

  Solve problems with a USB device

  Can someone help me solve these problems?

  Thank you

  Arif Bellah

  Hi Arif,

  Thanks for the reply.

  Are you facing any problem during the installation of Windows updates? If Yes, do you have any error codes?

  Method 1:

  I suggest you to download and install the latest Chipset driver on the manufacturer's Web site and check if it helps.

  http://us.gateway.com/GW/en/us/content/drivers-downloads

  Method 2:
  I suggest you to use Visual keyboard to type the password on the login screen and check if it works.

  Use the keyboard to the screen (OSK) to type

  Method 3:
  If the issue occurs when you use the keyboard on the screen, this could be a problem with the keyboard. I suggest you to connect an external keyboard and check if it works.

  Hope this information helps. Reply to the post with an up-to-date report of the issue so that we can help you further.

• iPad with Safari after upgrade issues

  I have an iPad model no MD526B/A and since the upgrade I have problems with clicking through websites of salma and Mail.  Any suggestions?

  This is a common problem and there is currently no permanent solution.

  Try turning off JavaScript under settings - Safari - Advanced.

• Qosmio G20-114: Vista upgrade issues - common Module driver is blocked

  I have the Qosmio G20-114 P - M 770/XP MCE /... Part number: PQG20E-00D003EN

  I've upgraded to Vista... and receive a message from driver error driver Toshiba common Module is blocked because it is incompatible with Windows Vista.

  I was running Windows XP MCE. Download a newer version of the driver that would work on this machine and with vista?
  I found a later version of this driver for other models...

  Hello

  No, you can download the latest version of common for Vista modules because the Toshiba has not released drivers Vista for the Qosmio G20

  This error message is displayed on your laptop, because the common modules only work with XP!
  If you want to upgrade XP to Vista you must first remove all incompatible applications.

  See also this thread. It of on the same topic
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=21163

• Qosmio F10: RAM upgrade issue after replacing the motherboard

  In 2006, when my F10 - 128 fell down as a fault of the video card, Toshiba has replaced the motherboard (865 PM) of my F10 by a new one with the video card installed in Go 6600.
  When I came back, I noticed that the same RAM modules have been installed (2 x 512 MB DDR 333 Mhz) as I previous had on the old motherboard.

  Then, I assumed that I could easily upgrade to DDR2 RAM, I realized that this type of RAM supported by the new motherboard installed (915 PM?). But the modules DDR2 Ram (Kingston 1 GB SODIMM (KVR533D2S4 - 1 G) 533 MHz) that I ordered is simply not in the storage media... The notch in the module is placed differently that the modules of RAM DDR.

  If the jury has been replaced by a newer version, with the video card Go 6600 (PCIexpress), how is, I have a Council that can not support DDR2?

  Here, I am really confused. Someone at - it advice please?

  > If the jury has been replaced by a newer version, with the video card Go 6600 (PCIexpress), how is, I have a Council that can not support DDR2?
  I think the jury is still supported DDR2 memory modules, but the allocation of the memory pins could be different.

  You should contact the ASP in your country and ask for the compatible modules.

• HP ProBook 6550 portable PC b: Re: RAM laptop HP ProBook 6550 b Upgrade issues.

  Info on my ProBook 6550 b HP PC:

  Intel Celeron P4600 @ 2.00GHz CPU 2.00 GHz

  2 x 1 GB RAM (1.86 GB usable)

  System type: 64 - bit operating system.

  Windows Pro 10.

  Query: I bought 2 x 4 GB RAM DDR3 1333 MHz 204-pin SODIMM Unbuffered of CCL Computers Ltd. After searching for the correct specifications on here to upgrade my RAM.

  I installed this new RAM carefully and booted up my laptop, only to be greeted by a blank screen / black.  I have re-installed the new RAM and rebooted my laptop, leading to the same result.

  I contacted CCL Computers Ltd, who recommended that I return the RAM to them for testing. However, they also mentioned that I should contact the constructor (HP) and ask them - your "QVL" (list of qualified suppliers) for successfully piloted ~ known RAM.

  So, with the above in mind, can you recommend a tested / experienced 4 GB of RAM running on my laptop, please?

  Already mentioned somewhere on one of these forum pages for "Corsair DDR3 4 GB of RAM of the laptop (CMSO4GX3M1A1600C11)"

  I'm also upgrading my laptop to SSD HARD drive.  I visited your forum pages and read that an SSD with a capacity of 250 GB is the optimum size.  Can anyone offer any known SSD fact / correctly upgraded for a laptop of my setup, please?   (See the top of this message to my HP ProBook specifications.)

  Looked at your comments and recommendations will be highly appreciated.

  Thanks a lot waiting for your answer.

  Hello:

  Please see this post below... Read the full thread.

  http://h30434.www3.HP.com/T5/notebook-hardware-and-upgrade-questions/memory-upgrade-6550b/m-p/5340551#M207994

• The graphics card upgrade issues...

  I recently bought this graphics card: http://www.tigerdirect.com/applications/searchtools/item-Details.asp?EdpNo=5660536&sku=A271-5774

  Also, I advanced and bought this power supply: http://www.tigerdirect.com/applications/searchtools/item-details.asp?EdpNo=3276573

  I own a HP Pavilion a6414 and this is my first video/graphics card upgrade.  I did a good bit of research and I know that I have the PCI E x 16 appropriate for the card slot and the power SUPPLY 650 Watt PSU to insert in the ATX case. I measure the UAP present btw.  I'm a little worried about the upgrade of the power supply, because I read somewhere (I think it's here on this forum) that some HP tech rep said a person who upgrade the power supply could not be performed on the a6414, but I don't see why not.

  My other concern is about the speed of the processor to the graphics card and possibly voltage problems, but I think the power SUPPLY Ultra PSU will be fine.  Either that it is my first time to play with the graphics card and PSU, I'm looking for advice on the compatibility between these three components, i.e. the model, the card and the power supply.  Any input will be greatly appreciated.

  Thanks in advance...

  I installed everything today and it works like a charm.  I had read so much about the HD 5770 not recognized by HPs and the test of the power supply, but everything worked so far.  I bought a LG LED 20 "monitor today as well, and everything looks great.  Thanks for all the advice guys...  The links you provided helped with Dave BIOS, thanks.

• HP Pavilion 15n - upgrade issues lower windows 7 (FN, aero peek and sleep keys)

  Hello

  I recently bought a HP Pavilion 15 (n097), which is pre-installed with windows 8... naturally I went down to Windows 7 and installed as a good number of pilots required system I could get my hands - everything seems to have worked pretty well, the only problem now is that:

  (1) I have no option "sleep" in the start menu, it is grayed out (only to stop, restart and hibernate are available)

  (2) making the skimming between surprisingly heavy programs is not supported by aero peek

  (3) none of the function buttons work

  I would be VERY grateful if anyone knew where I might be able to install the necessary drivers so that I can fix these problems were.

  Thanks in advance.

  tassilov

  You are the very welcome.

  Sorry the quick launch of the software did not work.  Unfortunately, I won't be able to provide additional assistance to this issue because I don't know any other software that you can use for this purpose.

  Here is the link for the graphics drivers that you need.

  https://downloadcenter.Intel.com/Detail_Desc.aspx?agr=Y&DwnldID=23405&lang=eng&OSVersion=Windows%207%20(64-bit) * & DownloadType = 0a % 09% 09% 09% 09% 09% 09% 09Drivers % 0 a 09 09% 09% 09% 09% 09

  If you have not installed the Chipset Intel driver, I highly recommend you first install and reboot the computer before installing the graphics driver.

  https://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y&ProdId=816&DwnldID=20775&keyword=chipset+installation+utility&lang=eng

• (Redirected) Server upgrade issues

  I need to upgrade my server.

  I've been using a 400SC for about 12 years with Server 2003 and it has served us well.

  I have 8 client machines.

  The server is a domain controller and a file server for 2 programs.

  No mail electronic or other uses.

  I am trying to decide what machine to update and continue as we are for several years.

  I hope I can shoot with Server Essentials of 2012.

  Ideas or recommendations.

  I don't want RAID.

  Don't like a single HD in my server.

  Best of this post in the Forum servers, here:
        
  http://en.community.Dell.com/support-forums/servers/default.aspx
       
  Bev.

• Windows7 and Installation/upgrade issues updated Itunes: HKEY errors

  I am running on a new laptop with Windows7 64 - bit OS.  I have already installed Itunes v9.0.3.15 on this computer, but when I open Itunes I got the following error:

  "Warning.  ITunes has not been installed correctly.  If you want iTunes to be able to retrieve information from the internet CD, you should reinstall iTunes. »

  Very well, but every time that I try to uninstall or update Itunes by installing the latest version, I get the following error at halfway through the installation process, on which the installation rolls back immediately and I'm stuck:

  «Could not open key: HKEY_Local_Machine32\software\classes\.pcast.»  Check that you have sufficient access to that key or contact your support team. » 

  I've looked everywhere.  I saw a lot of similar questions, but none exactly the same thing on other forums, and no resolution to other questions helped.

  I don't have this key in my registry editor because it is a 64-bit OS, so there is no "HKEY_Local_Machine32" only "HKEY_Local_Machine."  I have ensured that I do infact have full access to the 'HKEY_Local_Machine\software\classes\.pcast' , but the installation/uninstallation process is looking for the machine32 key.  NOTE: I am trying to install the 64-bit version of Itunes.

  The itunes forums have not proven useful.  If anyone has experience/solved this problem, I would certainly appreciate any suggestions.

  
  

  Hi bburkhart,

  To register permission number, install and run SubInACL to your computer to fix the permission issues.

  You can get the download here:

  SubInACL (SubInACL.exe)

  http://www.Microsoft.com/downloads/details.aspx?FamilyId=e8ba3e56-d8fe-4A91-93Cf-ed6985e3927b&displaylang=en

  This seems to have helped others facing a similar question.

  See this for example:

  iTunes 9 install on Windows 7 64 bit

  http://discussions.Apple.com/thread.jspa?threadID=2153424

  That should do the fix.

  Before you run the SubInACL tool, please make sure that you take a backup of your registry and also create a restore point.

  Here are the links for your reference.

  Back up the registry

  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  Create a restore point
  http://Windows.Microsoft.com/en-us/Windows7/create-a-restore-point

  Important note: This response contains a reference to third party World Wide Web site. Microsoft provides this information as a convenience to you. Microsoft does not control these sites and no has not tested any software or information found on these sites; Therefore, Microsoft cannot make any approach to quality, security or the ability of a software or information that are there. There are the dangers inherent in the use of any software found on the Internet, and Microsoft cautions you to make sure that you completely understand the risk before retrieving any software from the Internet.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.