Auto on/off problem printer Laserjet M2727 MFP

Similar Questions

• HP LaserJet M2727 MFP Series PCL 6 - prints the blank page before and after each document in all cases

  HP LaserJet M2727 MFP Series PCL 6
  prints blank page before and after each document in all cases
  Does anyone else have this problem.

  It must be a preference setting, but I watched three times and CAP does not seem to determine what setting to change.

  See if they help you:

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?lang=en&cc=us&ObjectID=c01477176&prodTypeId=18972&prodSeriesId=3377075

  http://h30499.www3.HP.com/T5/printers-LaserJet/LaserJet-M2727-NF-can-I-suppress-blank-pages-with-this-printer/TD-p/2359555

  http://superuser.com/questions/315522/computer-prints-blank-pages-before-and-after-content

• ATI Mobility radeon HD 4500 series reported an error code 43 and he he had stopped working, so my printer Laserjet M1132 MFP had stoped printing.

  My computer said that ATI Mobility radeon HD 4500 series reported an error code 43 and he he had stopped working, so my printer Laserjet M1132 MFP had stoped printing. How can I make it work againg?

  SHELF MODEL: tm2-1010ea

  SERIAL NUMBER: CNU0290H5H

  Any required driver updates should come from your support site for PC manufacturers, HP? and not Ati or windows update

• Printer LaserJet M1132 MFP range

  I have this printer.

  Sometimes it prints and sometimes not.

  I went through the section of troubleshooting and at one point, he said that the problem was fix. And I printed a page successfully.

  But now, it does not print any more. I repeated the steps "help out", but now it telling me that it cannot find the problem.

  Pls HELP

  Have you tried that?
  http://h10025.www1.HP.com/ewfrf/wc/document?cc=us&LC=en&docName=c02073861&JumpID=ex_r4155/HHO/IPG/ccdoc/trailhead_doc&lang=en

  I hope this helps.

• Printer LaserJet 1536dnf MFP range: software LaserJet1536dnf of print settles

  I had several problems with my LaserJet1536 printer so I uninstalled all HP software. I tried to re - install the software three times, but I've always had this message:

  Error. A Setup operation took too long to run. It is a fatal error, preventing the use of the product. Restart your computer and run this installer again. If the problem persists, please visit the web site of product support for your product.

  On the first two attempts, I used the original CD-ROM for Windows came with the printer. On the third attempt, I downloaded the software installation of HP and used, but to no avail.

  I disabled Avast Antivirus, but which did not help.

  Any suggestions?

  Hello @Aselene,

  Great stuff! Glad to know that you were able to solve the problem.

  Think about scoring my post as "accepted solutions" to help other users with the same issue to find a solution more efficient. Click on "blows upward" give me "Bravo."

  Visit us again if you have any questions!

  Thank you

• How to cold reset the printer Laserjet M175nw MFP Color 100?

  Try changing the settings wireless, but keeps on asking for a password that I don't remember.

  Printer works fine so hard connected to the network.  ePrint works very well.

  Just updated to the latest firmware available.

  I just need to change the wireless settings that I recently changed my password for wireless network.

  In addition, access to the menu is disabled from the control panel of the printer.

  So the only way that I can think of is to reset the printer and start the installation from the top.

  Thank you.

  Hello

  You must perform initialization of storage generally in order to remove the password configured in the fuly, any other reset will not erase this kind of configuration.

  In order to perform this reset, you should contact HP Support.

  You can get the details to contact HP by selecting your region and following technical support after purchase below:

  http://WWW8.HP.com/us/en/contact-HP/WW-contact-us.html

  Kind regards

  Shlomi

• I'm cann't print my printer LaserJet 1536 dbf MFP by Tcp/IP

  I installed the new printer laserjet (dnf MFP HP LaserJet 1536) with driver when I download from the HP Web (Full Version).

  When the driver installation is finished I have connected answer my printer with the mode of manual configuration of networking (TCP/IP)

  After that I already finished move to test the scan with flat screen, charger charge, fax / output, but cannot print

  but I use the USB cable to connect my printer could print

  Question: how to configure the printer to print with TCP/TP

  Hello MoUOun,

  Welcome to the HP Forums!

  I understand that you are unable to print using the Laserjet MFP 1536. I will do my best to help you! First, what is your operating system on your computer? Windows or Mac?

  I recommend you to download the print and scan doctor, to check if this utility corrects why you are unable to print. (It is only for a Windows computer.) Please post the results on this post, if this fix anything.

  Please follow this entire document of HP "Printer is off-line" Message appears on the computer and the HP printer will not print make sure that the printer port is correct, which is shown on this document.

  Please post your results, I will be looking forward to hear from your part, have a great day!

• printer Laserjet 1020 upgraded to windows 8.1 will not print PC HP Envy H8-1503

  Hello

  was wondering if anyone has problems printing of victory 8.1, used doctor HP printing and scanning and said everything's fine but a test page does not print as I can't print anything from another category windows 8.1. using windows 8 that I had no problem printing, I've updated all the drivers

  Also when I connect my laptop using windows 7 it prints, and with them turn off the printer laserjet 1020, then plug in the USB cable and windows 8.1 it will be printed.

  But when I turn off the 1020 laser jet, then turn it back on then try to print windows 8.1 that it will NOT print

  Thanks Mike

  Hello

  I understand that you can not print with Win 8.1.

  Drivers for win 8 and 8.1 Win are the two Version 9.
  Make sure that you uninstall the previous printer software.

  Here is a url to completely uninstall a printer in Win8.
  http://www.YouTube.com/watch?v=-M0GVVcwT-o

  Restart the computer.

  Reinstall the software of the printer again. Select full features software driver.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4131&LC=en&cc=us&DLC=en&sw_lang=&product=439320#N173

  If you need more simply make assistance let me know.

• HP LaserJet M4345 MFP: Network printer problem: cannot print, but can ping

  Good evening

  I have a big problem. We have a network HP LaserJet M4345 MFP printer. It is connected to a switch and the switch is connected to a Modem of Telmex.  It has a static IP address. 5 computers to connect to this printer, but I'm going to use one as a sample.

  The problem is that I can't print anything.

  • I can install the printer in all computers
  • I ping the printer
  • I can access the printer configuration using a browser
  • I can even scan a document

  But I can still print the test page. We have a static IP and it does not repeat the IP address, the host name is unique and date everything is fine. I tried to ping to test for the default gateway and it a ping with a correct response time.  So:

  • The configuration of the printer can be accesed via browser
  • The computer can ping the printer
  • I can scan a document to the PC
  • The printer installs very quickly in all machines
  • The printer can ping the default gateway
  • The IP address and the host name are unique

  What could be the problem? I tried to print in all the machines without success.

  Thank you for your attention.

  It is possible that the network adapter has a problem but since it's your only work around would be to buy a direct jet EIO card and put in the EIO slot in the back near where the network cable is plugged.  They are fairly cheap on ebay and you want to buy a 610N, 615N or 620N one of these models will work.  You must assign an ip address that is different from the one assigned to the integrated card.  I think that there is a way to disable the built in network card, but I have to carry out additional research on that.  If you have an old hp printer that you do not use with a network card eio, even if older 600N it will work in this printer.

• HP Color LaserJet M277dw MFP: Disable auto power off after inactivity for HP Color LaserJet M277dw MFP

  What is the purpose of mobile printing solutions if you cannot activate your home printer?
  My printer stop automatically after 8 hours of inactivity and therefore makes it impossible for me to use mobile printing. The printer is connected via WLAN (without active ports to stop the closing).
  In the configuration, there are only options to stop after 2, 4 or 8 hours. No option on disabling of automatic shutdown.
  Pls do that for the people who work on the firmware updates, they must include an option to disable auto power off, many people are already complaining that and nothing has changed so far.
  Its just illogical. You make big announcements for HP eprint and other stuff, but your printers are not able to do so even if you could theoretically make eprint if your standing next to your printer all day.
  I just got this printer pluged and installed and already tired of this BS!
  I know that there is no solution, so just send it to the people who can change it.

  for all of you who read this post, I was in contact with the technical team of HP and they said that they don't give you the ability to disable auto power off on purpose, it is HPs energy-economy-policy to do and there are no plans to change this in the future
  in my case, I only WLAN's, yet is not automatically stop (although it should be), I guess I'm lucky that my router it ping every now and then and is therefore not stop
  If you can't fix it yourself with active ports and may not have at all, it will probably not option left than the back of the printer

• HP LaserJet 1536dnf Mfp: HP Laserjet 1536dnf MFP - print problem printer

  My office has a printer HP LaserJet 1536dnf MFP printer and copy machine and it's only last month a year.  This morning the computer was printing and copy fine, then in the middle of a print job 21 page pages begins to show the 4 brands of blackshadow - like on the right side of the page (starting at the top and down to about 4 inches before printing the next black shadow).  Sometimes copying and printing.  I tried to reset the printer by unplugging the power for 10 minutes.  I tried to clean it with cleaning setting.  So far, nothing has worked.

  Greetings;

  If you could post a small picture of the question I might better be able to determine the cause.

  Are marks on the page dashes in the media?

  Brands repeat down the page in a spaced identical schema?

  The issue might have to do with the toner drum, but could be a piece of paper stuck on the fuser unit.

  Unlike the intervention of Anonymous_Fan this is not a model of injket and has no heads printing or alignment of the calibrations.

  I followed this thread and waiting for your response.

  Kind regards

  Jaclyn

• LaserJet Pro 200n: problem printing PDF with HP Laserjet Pro 200n

  Hello

  I have problems printing of PDFs of our color laserjet pro 200 hp MFP M276n.

  I get a sheet of paper and a blank message on the printer saying 49 service error - power off, then on

  I can print from word/excel documents. It started only recently, and the printer used to work properly. I have updated the firmware of the printer from the Web site and also downloaded the new driver software and deleted, reinstalled the printer.

  Connected printer throgh network, using the static IP address. I have reset the default printer and reinstall with a different IP address. The problem still exists.

  Let me know what to do for them.

  Hello

  My printer now works, and it is wrapped only because two or three color toner runs out, and the printer to enter this mode. Really stupid... as I tried to print the document B & W, and then set the options pint to print grayscale.

  In any case, the solution for me is that make sure toner all have dye in it, and youi don't have no cominng message saying 'Replace cyan"etc...

• LaskerJet HP 1022: Having problems printing. Seeing flashes and does not turn off.

  I have problems printing.  I turned the printer on / off power several times to cancel the print job.  There is a red light flashing and I am unable to stop after pressing several buttons.  I apologize because I don't have a book.

  Here is your complete support page.

  http://support.HP.com/us-en/product/HP-LaserJet-1000-Printer-series/439424/model/439431/manuals

  Download your User Guide and read.  Here he also troubleshooting for you.  Good luck.

• Problems with the LaserJet M1217nfw MFP - resolution of the Scanner and ADF feeding issues

  Feature: LaserJet M1217nfw MFP

  Connection: Ethernet

  OS: Windows 7 Pro 64-bit

  1st problem: using the TWAIN software, I am unable to change the resolution of the documents I'm scanning. It displays only the 300 and the menu drop-down does not offer any other parameters. It is having to make each document that I scan a lot more big that it must be, and the company I'm downloading of complained them of the overused storage space.  Device MUST be based on the network for the office.

  2nd problem: the ADF is VERY picky. If the paper is inserted at the stop, it will not pick up and will keep scanning out of the original glass. I usually have 2 or 3 times to find the "sweet spot" where it will actually be a new Pick-up analysis.

  I must say, I was very happy with this product when we got it first, the web interface with the drivers loaded on the printer was a great feature and the installation for each machine went very smooth. However, lately this device became more complicated than a time saver.

  Hi SilentbobSC,

  Follow the steps below.

  1. click on settings

  2. remove the checkmark of "Display the dialogue from TWAIN to allow cropping and low sweep"

  3. click on the drop down arrow to adjust your ppp settings

  

• HP LaserJet Pro MFP M125-M126: cannot set the default printer

  Hello

  We have HP LaserJet Pro M125 - M126 PCLmS network MFP all in one printer, as the installation of all users was a success and was working fine the day of installation, after a day all users face the question cannot set default pritner, cannot print, all users are faced with question at a time ,

  quick response is appreciated,

  Hi @darshan9 ,

  I see that you have problems affecting the default printer for users and you cannot print over the network.
  I'd love to help you.

  Do you mean the configuration of individual computers with the printer on the network users, or a computer with multiple users?

  You have administrative rights on the computer to make changes?

  What is the name and the product number of your printer? How can I find my model number or product number?

  Download and run the Print and Scan doctor. It will diagnose the problem and could solve it automatically. http://www.hp.com/go/tools > using HP diagnostic tools for printers under Windows HP.

  I suggest you to check if you have another account user or an administrative account.

  I also suggest to create a new user account and check if you are able to set the default printer.

  Create a user account. Create a user account.

  If you're still having problems, run the Fixit tool. Diagnose and automatically fix problems printing and printer.

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  If there is anything else I can help you, let me know.

  Good day!
  Thank you.