Autonomous aPs with several SSID in a VLAN?

Similar Questions

• Standalone WAP several SSID to a single VLAN

  I have an AIR-AP1142N-A-K9, I use for my home wireless. I am trying to use the 5 GHz and 2.4 GHz radio, so I can have the SSID and SSID [5 GHz] announced. It seems that I am unable to set multiple SSID to use a single VLAN. I searched a doc or config with this subject guide, but I came up empty. The config at the end that I'm looking creates four SSID. A guest and SSID private radio with the SSID of comments on one VLAN and the private SSID [encrypted] on another VIRTUAL local network. Any help is greatly appreciated.

  Hello

  Pls check this doc...

  https://supportforums.Cisco.com/docs/doc-16087

  If you still don't get work, please paste the config.

  Thank you!

  Concerning
  Victor V

  "Help others using the system of rating and marking answers questions as * answered."

• SA520W VPN from Site to Site with several VLANs

  Hello

  I have a customer here with several VLANS in their places who wants to set up a VPN from Site to site between 2 devices SA520W. Unfortunately I can not find a way to set it up. In the VPN policy, I can choose between everything (which is not what I want, I want only traffict between subnets the routed via VPN), IP address unique, a beach (in a subnet) and a subnet itself - but only one. I don't find a way to configure several subnets in the selection of local traffic and remotely. Adding another IKE policy between the 2 sites does not either (which is good normally).

  Any ideas? Anything I'm doing wrong?

  Thank you for your help.

  Best regards

  Thomas

  I know that if you have an ASA or a router, you can define as VLANS to pass through the tunnel.

  Do not have access to a SA520W to test...

  A recommendation might be to post the question on the SMB community where they answered questions related to this product, just to check what other people did.

  Federico.

• Roaming between two autonomous Aps in root mode

  HI guys,.

  (Q) what is the difference between roaming and mobility between two autonomous APs?

  I configured two APs of stand-alone mode in root mode with the same settings (same wlan ID for two VLANs) wlan. How does choose between these two APs clients to connect.

  I read a few docs and they said they will choose AP on the intensity of the signal. My question is, do I need to activate some kind of roaming/mobility between them so that if clients connected to an access point moving to the AP another area, they will automatically connect to AP with AP signal stronger.

  Or how the roaming/mobility between two autonomous APs

  Thank you

  HI Safarazaz,

  Info: About the connection to the access point, the customer makes the final decision based on the use, the power of the signal... etc.

  So now we come to the point on homelessness:

  IF you use a WPA/WPA2-PSK, then all you need to do is configure the AP exactly the same way, with the exception of the IP address on the interface BVI.

  IF you use 802. 1 x, then you want to configure WDS to the cached key.

  http://www.Cisco.com/c/en/us/support/docs/wireless-mobility/wireless-LAN...

  Concerning

  Remember messages useful rates

• WiFi HP ENVY 4500 with several Access Points - same SSIS Configuration

  Hello

  We just got a HP ENVY 4500.  I have a main homenetwork with a wifi Modem/Router and an old router acting as an Access Point to the floor to extend coverage.

  Both have the same SSID and password and are set to different channels.

  My HP ENVY 4500 fails to connect when the Access Point is lit.

  It will connect with it.

  Once connected, I can turn on the PA and all is well.

  The two router an AP using WPA-PSK/WPA2-PSK encriptación

  The router (that it connects to) should have a better sgnal when both are on, so I do not understand why they need the AP to be turned off to connect.

  Any thoughts people?

  Eserim

  I think he has always had problems with several access points.  Try this, what ever AP is closest to the printer, set it to channel 1.  Then try channel 11.  Try now.

• Shortcut for the new window with several tabs

  Is it possible to have a shortcut on the desktop to launch a new window with several tabs? For example - home page is set to "www.google.com", but the shortcut opens new window with tabs "www.cnn.com" and "www.youtube.com".

  Then far,.../firefox.exe-nouveau-fenetre followed by the two URL in quotes will open two new windows. Entry - new-window "www.cnn.com" - new-tab 'www.youtube.com' will open two new windows if no instance of firefox is open, but if another window is already open, youtube will add a tab to the already open window, rather than the new window with cnn.com

  In reply to myself... withdrawal-order new window (and-new-tab), now it works.

  Looks like I'm too complicated it.

  shortened final was "C:\Program Files (x 86) \Mozilla ' 'url1'"url2.

• Functions defined by the user with several parameters

  I set features three following user using "Define."

  UF1 takes a single patameter;

  UF2 takes two parameters;

  and UFX takes two parameters - with the second is 'X' in the definition.

  

  Œuvres F1.  F2 is the EVAL of F1 version and it works too.  User functions only seem to work fine.

  F3, a function of two user settings, produces a graph of NaN.

  F4 is the EVAL of F3 version.  Note that 'B 'is not replaced by 1'.  Also produces a NaN chart.

  F5 produces a graph of NaN.

  F6 is EVAL of F5.  The 'X' is not replaced (even with the ' B' above), and even if it looks like 'X * X', it also produces a graph of NaN.

  

  Is it possible to get defined by the user, with several parameters, features work by tracing the curve?

  Hi!, Fortin:

  If you download and install the ultimate Firmware with the version of the software: 2015 6 17 (8151), with the number of Version: 1.1.2 - 11, you can trace your examples of definition of the function, with curves and values, without NaN.

• Background with several pictures

  How can I create a wallpaper for my iPad, iPhone, MacBook Air with multiple photos?

  (El Capitan, iOS 9.2.1 Photos)

  To create a collage of photos, you can create a photo book project and select a template page with several photos. Fill it with photos of your choice and print the page in PDF format.

  The themes of the book are different according to the terms of the photos and the number of photos per page.

  It's the theme travel plans:

  

  If you have installed iWork apps try Keynote to create a slide with many photos, arranged freely.

• Carpet * a DVD-Ram UJ - 841S comes with several error messages

  My laptop is relatively new, I've been burning some video files in DVD - RW and all of a sudden my DVD drive has stopped working. It came with several error messages format "failed due to damage media", "format failed due to general failure" and "the inserted disc is READ only".

  I also can't rip music discs.

  Can you see ODD listed in Device Manager, and if so what is the exact status it?

  Sorry, but we discus on ODD, but nobody knows what model of laptop you have and what is the history of this problem. Is replaced the drive? Why are you sure that you are using compatible with your laptop ODD.

  Please more information!

• Interfacing with several unknown USB devices; all producing NMEA strings

  Hi all

  Question about the peripheral USB interface and their associated drivers.

  I have the obligation to build an application that interacts with the USB devices that produce NMEA strings. I have the library to parse NMEA strings, but I fight with interfacing with several unknown USB devices. When deploying applications, I know not all possible USB devices to use.

  Is it possible to produce one driver who will accept any USB device strings?

  Or, more likely, is there a way to get the LV to recognize a connected USB device and automatically find / install the driver like windows does and is it possible to do in a deployed application?

  I had a trawl of the forums, but I've not found anything that specific.

  Thanks, I really appreciate the help.

  About the VI "set up the serial port", my problem is that the choice of COM port is in a separate menu (not directly related to the VI) and it allows all possible COM ports to be selected. That can be addressed.

  I am not expecting an all-in-one solution but asked the question in case it was possible.

  What I realized, is that for my specific condition to read strings from a USB device. It is likely to be sent over a serial connection. LV can handle this well and easily assuming the device has the installed driver / settings are available.

  LV (and indeed any other program) will not work without a device driver / settings. In this case, parameters set must be found (error) / a USB RAW driver would need to be developed. Devices requirng a RAW USB driver would need a serious review to continue due to the time and effort required. All this effort is work inherited from the AIDS to navigation

  I appreciate any help and I think I got the answer I was looking for! Thank you very much

• Closure of a state machine in queue event with several parallel loops

  I am trying to find the best way to stop a program that consists of an architecture of State machine in line waiting for event with several parallel loops. Can anyone recommend the best way to achieve this in my attached VI? (To browse the forum, this seems to be a frequently asked question, but I have not found a solution that works for me.)

  I look forward to any comments on my as well code, if someone is willing to offer it.

  My program needs:

  If the user press the 'Stop' button, the program should prompt the user with "are you sure you want to stop the program?" and then return to a State of rest or move forward to stop the program. In addition if there is an error, the program should prompt the user to ' clear the error and continue, or stop the program. Then back to the idle state or move forward to stop the program.

  Architectural details:

  The program consists of 3 parallel loops: (1) a loop of event management that places different States of a queue of the State, (2) a State Machine that enters the State that is removed from the queue of the State and (3) a loop error/Shutdown, which deals with errors in the error queue management.

  During normal shutdown, where running handling loop in the case of event 'Program.Shutdown' and 'Shutdown' and the 'Idle' States are added to the queue of the State. In the state machine, the State of 'Stop' is invoked. Special "5000" error code is added to the queue of the error. In the loop of error handling and stopping, "5000" error triggered a prompt that asks the user if they want to stop the program. If the user chooses not to stop, a notifier StopNotif is sent to the State of 'Stop' and 'Program.Shutdown' event case with notification 'Go '. If the user decides to stop, the Notifier sends the notification "Stop". Loop and event management State Machine ends when they receive the notification "Stop".

  In case of error, the program behaves in the same way: If the user chooses to clear the error and continue, the program returns to the status "pending".

  HOWEVER - if the user chooses to stop the program, the program crashes. The author of the notification that is sent to stop the loop of events and State Machine management cannot be read because event Program.Shutdown and the stop State (which contain the function "Waiting to notify") are not active.

  I was able to activate the stop State by Queuing in the loop of error/Shutdown management. But I don't know how to activate the "Program.Shutdown" event by program and thus access the function "Waiting to notify" inside.

  I tried to put the function "Waiting to notify" outside the structure of the event, so the event-handling loop never ends. Placing timeouts on the "wait for declaring" and the structure of the event makes the programme of work, but I want to avoid using timeouts because I don't want to turn my event program into a program of polling stations. I would also avoid using variables or nodes property to stop loops, because that requires the creation of a control/indicator for something that the user does not need to interact with.

  Thank you!

  First of all, close the notifier outside loops with your queues.  Second, you must use a user event to send the message to the event structure loop so that it stop in the case of the stop on an error.

• Slide with several digital poster Down filter event Bug button?

  A key event filter on a slide with several digital screens down does not work as expected when not waived. If you for example tab of this slide with two digital screens digital display, the cursor remains on his position, rather than get KeyFocus to the next control. Same behavior at fault if you want to move the cursor on the left/right keyboard, nothing happens. Anyone an idea why?

  A simulation of that VI is attached. All other controls, a Slide with a digital display or a standard digital control, the key Down event filter behaves as expected... I tested in versions 8.5.1 LV (attachment), LV2012SP1 and LV2013.

  A teammate now found a solution or workaround. We do not know if this is the way it should be, if yes, then it's a bit hidden, but it works!

  It seems that the cursor needs to know on what digital display the FocusObj is when you use the event notifier KeyDown. Then, when to get the reference of the digital display active and the wiring of this reference to the terminal FocusObj filter event everything works as expected, numbers of tabs, typed, cursor etc and have to filter and notify events structure to the event.

  A vi and a printscreen are attached.

  The question is probably due to the specialty of slides and the class NumericWithScale in general, as its digital displays are a little under References and during the implementation of the features of event KeyDown for the class NumericWithScale filter, LV simply does not know on which side of the main action control part must be executed.

  Or someone has a better solution and explanation?

• problem with several graph XY axes

  Hallo,

  I'm tracing different variables in the same plot with several axes. I have the following problem (see attachment)

  the y axis secondary on the right side of the plot has a large area of him and one of the other secondary axis falls right above others. I tried it in the two labview 8.2 and 8.5 with the same results.

  any ideas?

  Thank you in advance,

  Thodoros

  Try the following movements:

  Right-click-> popup menu-> advanced-> reset scale layout

• HP Officejet 6500 a how to scan a document with several pages in a single file?

  HP Officejet 6500 a Plus e-All-in-One - E710n

  Windows 7 (64-bit)

  How to scan a document with several pages in a single file?  After each scan, my old printer (psc 2110) asked if I wanted to scan another page.  In the end, I got a PDF with multiple pages.

  This new creates a file for each page, and I can't find a way to create a PDF with multiple pages.

  Hi mpw101,

  You must press the Add/Remove button, to add pages additionla scanned to the existing file. If you do not see this button try decreasing the analysis DPI setting. Let me know if this helps you?

  

• I'm stuck with several GB of music files on my phone and I can't get down them!

  The other day I tried to install an application on my phone, but I didn't have enough memory.  My phone is full of music via iTunes synchronisation dock. So I connected it to my computer to try to make some more room. But there is a problem.

  (1) Apple does not play nice with Palm. Synchronization is no longer permissible or possible. I can't use iTunes to manage/delete music.

  (2) in USB Mode, there is no way to access/view the library. It's just not there.

  I tried Palm support, and they confirmed that the USB Mode is not working. I guess that the library is located in a hidden folder or directory. They suggested that I downgrade my iTunes. Goal that is unacceptable to me because one) it forces me to break the license Apple, b) it is not taken in charge, and c) if there is still a remote chance it will mess up my iTunes library, I won't.

  I'm ready to get off at Palm headquarters and throw my phone to their building.

  Can someone tell me how to delete my library without hacking iTunes?

  I thought about it. Support, put this in your KB. Everyone who was sync via iTunes on a Mac is currently STUCK with several GB of music on their phone that they cannot manage or remove, which makes the Palm Pre a lot less useful than announced.

  USB mode is a waste of time for people on a Mac. These hidden files are never going to be visible, and the library cannot be removed. The solution: go through a PC. Anywhere, any PC will do. Connect your phone to the PC, go to the USB drive Mode and show hidden files, then delete them from there.

  I got an old laptop lying around at the bottom, and the problem was solved lickety split.