Bad Apple arobase ID on

Similar Questions

• Apple updates using bad apple id

  Trying to apply updates on my iPhone of Apple 6 he asked access code for my Apple ID girls not mine. I checked icloud and the framework general and everything seems ok and put my Apple ID but if I try to apply updates it asks password for different apple id. That is to say my girls. Any ideas?

  My hypothesis is that the applications must have been purchased with Apple ID your daughter purchases are always related to the ID that was used to make the purchase.

• Bad Apple Watch - Venezuela time

  recently in Venezuela, they changed the time by removing a half-hour of chavez.

  Now, the phone is fine and displays the correct time but iWatch remained with half an hour of Chavez. I solved it by changing to 30 minutes in the watch of installation, but not good because the alarm clock and all the rest shows me the wrong time.

  How can I solve?

  Hello

  One solution suggested by another user is to set the timezone manually in San Juan, Puerto Rico:

  -On your iPhone, go to: settings > general > Date & time > turn off the value automatically > type on the time zone and the search for San Juan, PR

  Note that the existing calendar event calendar, reminders, etc. may remain imprecise.

  It can help to restart your iPhone and Apple Watch after you make this change (turn the two together off the coast, then restart your iPhone first).

  More information:

  Apple Watch time differs from the iphone

  You can report the problem to Apple:

  - https://support.apple.com/contact/

  - https://twitter.com/applesupport

• Bad Apple ID after software update for iOS9.3

  Hello community,

  I updated my iPhone 5 this morning (since I was curious about the new version iOS9.3) and wanted to activate my phone after that, however, I still have the message ' incorrect Apple ID-... does not unlock this iPhone. ". I'm really sure that my ID Apple and my password is correct, I've actually changed my password to exclude this option, if someone an idea of what could have gone wrong and what can I do about it? Thank you!

  Best, Thomas

  I also have this problem. I did the same thing that you changed my password to see if it would help, I was told I wasn't using the ID. correct Apple

• Bad Apple ID

  Incorrect Apple ID "[email protected]" can be used to unlock this Apple Watch. I had literally just this brand new? HELP PLEASE

  Where, exactly, did you buy it?

• Bad Apple ID after matching Apple Watch

  Hello

  I have a Apple Watch, but last week I gave it to my friend to try it. I forgot to turn off pairing the watch simply reset it and give it. Now I get the watch back and after I have paired the device and agreed to the terms and services, I can connect on my Apple ID. But I still got the same message: Incorrect Apple ID, you cannot enable Apple Watch with this Apple ID.

  Now I've tried everything. Reset iphone settings, deleted the watch icloud my devices, create new apple ID, but I have always the same (even with the new apple ID). So, I have no idea how to do to activate the watch. I checked locking activation is enabled but I don't know why because I deleted the watch of my devices.

  Thanks in advance,

  Armin

  Hi Armin

  It seems Activation lock eventually applied to the watch (automatically) when he was paired with the iPhone to your friends.

  If Yes, you are able to associate the watch to your own iPhone again, your friend must first disable the function.

  Ask them to visit https://www.icloud.com/ and sign in with their Apple ID > settings > my devices > Apple Watch-click > click the 'X' > click on delete.

• iPad claims a bad Apple ID when updates to the app in the App Store

  Hello

  When I try to update using the updates shown in app store, for couple of apps App Store shows a different iTunes ID and its asking to specify a password. Can you help me get rid of this and continue to update?

  I had already tried to check the settings of the App Store and iTunes and there the user credentials and also I activated app updated it. Its does not help to resolve the situation.

  Can someone please?

  Thank you!

  Kind regards

  Pranab N.V.

  Applications (and everything that is downloaded from the iTunes Store) are linked to the account which has downloaded. The id that displays in the updates tab should be the id who them downloaded on your iPad (or downloaded to the computer iTunes library which you synchronized of)-to get them linked to your account, you need to remove the apps and buy/download in your account.

• Apple Store refuses to solve my problem of display iPhone 6s

  Hi all!

  I had a bad Apple Genius bar experience. They refused to solve my problem with my iPhone 6 s screen. There are black dots (dust, debris) on the upper left corner next to the "secret" key. I have already replace display once and twice got replacement unit. But the problem is still there. (looks like a problem of design with 6 s) This time I went to apple store and they refused to do anything by saying that we have already done what we could. Now, he must live with this problem.

  My apple care (1 year) one ends in November 2016. I'm still entitled to receive support from Apple, but they will not solve the problem (maybe there is no solution because of the poor design of 6 s).

  I don't know what to do. Could you guys suggest me a way?

  Thank you!

  Best regards

  Arslan

  You can let apple know how to use their feedback channel http://www.apple.com/feedback/iphone.html

• Apple id reset

  I keep one of my apple family id relaxing but can't seem to connect with the new access code, because the system always tells me that I have a bad apple ID or password I did individually.

  What could be the problem and why the reset does not work for me?

  < personal information deleted by host >

  Check these items and follow the instructions.

  If you have forgotten your Apple - Apple Support ID

  If you forgot your Apple ID - Apple Support password

  https://iforgot.Apple.com/appleid

• Problem with refresh PDFKit full screen

  I do a lot of presentations in PDF format (they are usually created with LaTeX, but I as explained below, this detail has nothing to do with the problem).

  Very often a slide appears in increments - think of several chips which are revealed one by one.

  What is really happening, is that each step is a separate page, but the user should not notice it.

  So if you have a bulleted list

  •A

  •B

  •THIS

  There are really three separate pages (one that contains just A, an and B and a with A, B, C).

  When you advance to the next overlay, it seems that a and B has been added to the screen, and then a C (even if every time an entire page is replaced by the next).

  In the Sierra this screen refresh is not smooth and the public can clearly see the screen "shaking."

  I tested it on two machines. I did a test of the Keynote presentation, which looks great; and then did the same with the PDF version and it is fragile. It was regardless of what program I used to view (Preview, Skim, TeXShop), which indicates that the problem is in the common framework, they use all - PDFKit.

  I already submitted comments to Apple, but I'd like to hear if people also see this; just to make sure that it is not something weird on my machines.

  Yes, I confirm this. It seems that PDFKit "re-focuces" fonts whenever we turn the page. While this might be great for static pages (best font anti-aliasing) is certainly a problem for presentations: you can clearly see the fonts from blurry to sharp in the slides with incremental changes. That's all just awful. On the other hand, PDFKit is not smooth images embedded in pdf files in the Sierra at all: those with straight lines will look on-screen civet. Once again, all just awful. Bad bad, Apple!

• Dock icons have been removed, but appear in the Applications folder

  Hi, I ve had some problems with the dock icons. Since yesterday I can't see native IOS icons like finder, mail or launchpad. However, I checked my app folder and here they are with the same problem. No native applications as google chrome has had the same problem, but once I have check the option 'get info' allowing the application I have fixed the copy of the problem and paste the icon. When I try with native applications, I could not. I don't know if it's a virus or what, but my macBook takes longer to rise. You have the same problem? You have to be able to help me?

  

  In assuming that you already restarted your Mac, try the secure boot mode.

  Stop your Mac. Use the power button if you wish. Now start with the SHIFT key is pressed. This will start in Safe Mode, with all extensions turned off. Safe mode is slow to start, so give it time, it checks a lot of staff. If it works fine in Safe Mode, restart normally. If it works now, you are finished.

  If the problem comes back after a reboot, you have an extension conflict. Disable all extensions via system preferences. To isolate which extension is at fault, turn on an extension at the same time, restart in the meantime, until you find the bad Apple.

• MPB starts only in the trunk in safe mode

  Retina MBP 2012 - mi 2012 • OSX - 10.11.6 (El Captain)

  I know that this is not a new issue, but I din't found a solution to internet research;

  This week, since when I have ' USB drawing too much power ", and then restarted my mpb - it can only start in safe mode. I did MSC and PRVM Reset but without success.

  Panic report *.

  panic (the appellant 2 0xffffff802e1ce6fa cpu): Kernel trap at 0xffffff7faf638b70, type 14 = page fault, registers:

  CR0: 0X000000008001003B, CR2: 0XFFFFFF813B80F274 CR3: 0X0000000031B18000 CR4: 0X00000000001626E0

  RAX: 0XFFFFFF813B80F26C, RBX: 0XFFFFFF7FAF5F4BC4 RCX: 0 X 0000000000000000, RDX: 0 X 0000000000000000

  RER: 0XFFFFFF81319F3C00, RBP: 0XFFFFFF81319F3E10, IHR: 0XFFFFFF813B80F26C, RDI: 0XFFFFFF8041E69900

  R8: 0X000000000000FFFF, R9: 0XFFFFFF813B80F26C, R10: 0 X 0000000000000000, R11: 0 X 0000000000000001

  A12: 0 X 0000000000000440, R13: 0XFFFFFF804240EA00, R14: 0XFFFFFF8041E69900 R15: 0 X 0000000000000000

  RFL: 0 X 0000000000010286, RIP: 0XFFFFFF7FAF638B70, CS: 0000000000000008, SS 0 X: 0 X 0000000000000000

  Lack of CR2: 0xffffff813b80f274, error code: 0 x 0000000000000000, CPU error: 0 x 2, PL: 0

  Backtrace (2 CPU), Frame: Return address

  0xffffff81319f3890: 0xffffff802e0dab52

  0xffffff81319f3910: 0xffffff802e1ce6fa

  0xffffff81319f3af0: 0xffffff802e1ec563

  0xffffff81319f3b10: 0xffffff7faf638b70

  0xffffff81319f3e10: 0xffffff7faeb21855

  0xffffff81319f3e70: 0xffffff802e6b6148

  0xffffff81319f3ee0: 0xffffff7faeb215b6

  0xffffff81319f3f00: 0xffffff802e10f2da

  0xffffff81319f3fb0: 0xffffff802e1c9117

  Extensions of core in backtrace:

  com.apple.iokit.IOUSBHostFamily (1.0.1) [79D250A3-843A-3750-BE64-A252CF17A148] @0 x ffffff7faeb19000-> 0xffffff7faeb82fff

  dependency: com.apple.driver.AppleUSBHostMergeProperties (1.0.1) [401B 7165 - 36E8 - 3EE5 - 849D - 71d AEB3E46E4]@0xffffff7faeb15000

  com.apple.driver.usb.AppleUSBXHCIPCI (1.0.1) [D08C7EEE-CA01-3053-8 D 47 - 2587BBCF9C9 5]@0xffffff7faf633000-> 0xffffff7faf652fff]

  dependency: com.apple.iokit.IOACPIFamily (1.4) [5D7574C3-8E90-3873-BAEB-D979FC215A7D] @0xfffff f7faf5e4000

  dependency: com.apple.iokit.IOPCIFamily (2.9) [F51AA3D6-EC2F-3AD3-A043-06DB79027AA2] @ 7fae97c000 0xffffff

  dependency: com.apple.iokit.IOUSBHostFamily (1.0.1) [79D250A3-843A-3750-BE64-A252CF17A148] @0 x ffffff7faeb19000

  dependency: com.apple.driver.usb.AppleUSBXHCI (1.0.1) [931A3E67-1954-320C-9619-C41C0A516804] @ 0xffffff7faf5ed000

  Corresponding to the current thread BSD process name: kernel_task

  If your Mac runs in Mode safe mode, but not otherwise, it is most likely, you have an installed extension that is the cause.

  Disable all extensions via system preferences. To isolate which extension is at fault, turn on an extension at the same time, restart in the meantime, until you find the bad Apple.

• Impossible to disassemble the repair disc

  Hey out there - I hope someone can help me with a solution to my problem!

  My drive external DRIVE (WD MY Passport) decide to stop playing on the same team earlier today.

  My Mac recognizes the drive, but won't let me access to his files directory - when you try to check the diskutil drive tells me it needs to be repaired, and in trying to fix it, diskutil says that it is impossible to disassemble the disc... > _ <

  But when accessing the control through the recovery partition I can also check and repair and it will come just by saying "all is * A - OK... When you use the diskutil through the recovery partition I can even access to its files directory, and it shows me all the files without any problems...

  If it becomes increasingly strange...

  Y at - there someone out there who has an idea of what to do with it?

  Best regards

  Stop your Mac. Now start with the SHIFT key is pressed. This will start in Safe Mode, with all extensions turned off. Safe mode is slow to start, so give it time, it checks a lot of staff. If it works fine in Safe Mode, restart normally. If it works now, you are finished.

  If the problem comes back after a reboot, you have an extension conflict. Disable all extensions via system preferences. To isolate which extension is at fault, turn on an extension at the same time, restart in the meantime, until you find the bad Apple.

• iPhone 6s more noise clicky - Home button

  Hello all, two months ago, I had a bad Apple of my iPhone 6s quality replacement more and now I have the following problem. I noticed that when I press the home button there is a different clicky noise and it feels like the button moves. It is really disturbing and annoying. I also compared it with another iPhone 6 s where there is not this problem. I went to the dealer for Apple in Bulgaria (due to the fact that there is no Apple store) and they said that it is normal. I contacted Apple Support by phone and they have asked for photos and videos of the problem. Two days after I received a call from stating them that it is not a question. However, I am not satisfied with this response and my problem is still not resolved. Someone has an idea what to do and how to proceed, to escalate the case more away?

  Thank you in advance!

  Hello

  If you are satisfied with the response from Apple, contact Apple again and ask if the question can be put together for review.

  I'm afraid that no one here can help you (you do not talk with Apple here - it is a community based on the user).

  • Контакт - Официална поддръжка на Apple
  • https://Twitter.com/applesupport

• NetRestore 10.11.4 and 10.11.5 Fail

  I used successfully for a some years netrestore to deploy our macs.

  Since I improved the image of the master and the server at 10.11.4 the process fails. Experience teaches that usually it gets noticed and fixed. Unfortunately 10.11.5 always has the same identical problem.

  I can still deploy the image based 10.11.3 (but hey it's a bread PITA to have to manually do all updates every time).

  Installation program:

  Mac OS X 10.11.5 + Server.app on mac mini server (tried multiple servers, even one on a clean install.

  • NetRestore image create with on and off a 10.11.3 system image utility machine hooked up via thunderbolt in target disk mode: continues to work as it used to do
  • NetRestore image created exactly the same way on and off the machine 10.11.4 or 10.11.5: cannot operate.

  Clients tested: multiple MBP of ranging from a new machine to a machine of 5 years. All the same performance: progress under the apple logo bar goes to 70/80% and that's all.

  Since the 10.11.5 server can still serve the 10.11.3 created image, it looks like not it's the server, it looks that the system image utility needs a fix.

  If you're REALLY patient (several hours), it seems the machines just down: hard stop is the only thing that they meet more - black display.

  So the question:

  Someone told 10.11.5 netstore base images work? What have you done to work around the problem?

  It's going to be really bad Apple out of new material that could have a customized version or something like that before they solve this problem.

  Well, I have to add one thing: while typing upwards above, I did some additional tests, and I tried on an old MPB had sitting on my desk for other reasons so he could start the server to a handful of times on one of the servers. As expected, there is a handful of times, but I left it hanging if you change the question here.

  And somehow, miraculously, it seems to have jumped through somehow. So the failure rate is not 100% (but given the amount of tests, it is so high at the point of being unusable in practice. But the absence of failure rate of 100%... could be more difficult to debug than necessary, especially given that the images do not want to start in verbose mode (or I don't know how to trigger the verbose boot during a netstore.