Similar Questions

• New EarPods works do not correctly with the old iPhone

  Hi, someone I gifted their EarPods. I tried on my iPhone 4S running on iOS 7.0.4 but to my disappointment only left side is audible to all the sound elements of music to Siri. right side is silent, not even low noise at full volume. All other functions of the EarPods as 'change volume' and mike work correctly. But then I tried on my computer laptop Lenovoand they absolutely worked well! The two sides were also audible and clear. I tried again on my iPhone 4s, but the problem occurred again! Other headphones work fine with this iPhone. Now, I know that neither EarPods jack iPhone is damaged (or blocked), it isn't a software problem and also compatible with the iPhone 4S as claimed by Apple. I have now run out of options. Please help me. Thanks in advance. (I live in India, where there is no Apple store, so please don't recommend me to get replace them)

  If you don't insert them completely what you describe happen

  could be a cause of why it is not able to go all way

  1. you did not apply enough pressure

  2. something got into the connector and cause the connector not being able to go all the way in

  all headsets with headphones apple 3.5 mm minijack or otherwise, have always been able to work with any device I connected their ios device or laptop or the likes.

• Questionnaire works do not correctly with the presenter 7.0.7 in LMS

  I use PowerPoint 2003 and presenter version 7.0.7. We previously had version 7.0.1 and quiz worked very well. However, I reissued a course with 7.0.7 and when downloaded on our LMS quiz does not work correctly if a user fails the quiz. Works fine the first time, but not if they fail and must go back.

  The course takes the user initially (as we wanted), but when they get to the quiz to resume it, they pick the correct answer, click on submit and nothing happens. A message should display the so-called "Correct" or "Incorrect" and click to go to the next slide. These messages are not displayed and the user cannot move to the next slide by clicking anywhere (which they should).

  It seems that, behind the scenes, that he might work because if I use the button forward/next down through all the questions after I answer them correctly, it will record that I have completed and passed the quiz.

  I ended up uninstalling 7.0.7 and going back to 7.0.1 and it worked fine. However, I would like to know if there is a solution to this problem so that we can use 7.0.7.

  Thank you.

  7.0.1 is a version quite buggy of the presenter. Have you tried to go to version 7.0.5 or 7.0.6 through the Adobe update 7.0.2? If identified when in the process of updating, there was a change which affected the reports feature to your LMS, which can help identify the problem. Personally, I recommend that you don't touch same presenter, unless it's on version 7.0.5 or later, because it it too great a risk to not do what you expect or just crashing and losing all your work.

  Also, if you access the training in IE9? I remember he had some compatibility issues with IE 9 and presenter, but I thought that was resolved in 7.0.7.

• D - Link USB Hub DUB - H7 works do not correctly with Windows 8

  I am also having the same problems.

  Very recently, I went from 7 to 8.1 and with the operation of the steam, the sound of connect/disconnect repeats about every 10 seconds. If I disconnect the D - Link DUB - H7 sound no longer appears.

  I could live with it for the time being cut just sounds system, but unfortunately the problems don't stop there.

  If I have my USB DAC (sound card) connected via the hub, pilots always crashes in a few minutes in Spotify or any multimedia player. It means that I actually listen to music at all.

  Hardware troubleshooting does not detect any problems at all. For now I'll connect my USB DAC separately and cut system sounds, but it is not a solution. Never had any problems with this hub in Windows 7 and I don't really feel like buying another usb hub since it fits my needs perfectly.

  Separated from -.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-hardware/d-link-USB-hub-dub-H7-not-working-properly-with/1158a3bc-487d-40C1-b3d0-2419ace3ef2e?page=2

  Hello

  Answer the next question to learn more on the subject, that you are facing.

  What is the brand and model of the computer?

  Install the chipset drivers by downloading from the website of the manufacturer of the computer and check the status of the issue.

  I also suggest you run the Fixit from the link next and if it helps fix the problem.

  Hardware devices do not work or are not detected in Windows,.

  http://support.Microsoft.com/mats/hardware_device_problems/

  Please let us know if you need assistance.

• PS6 works do not correctly with windows 10

  Is anyone else having problems with PS6 after switching to Windows 10?  Every bit of controls results in my image go black or the area outside the image to transform "into white" (checkerboard showing empty rather than dark grey which is usually the backdrop for the image I work with).  At first I thought that I could live with it, but now it's extremely annoying.

  Try this link.  I suggest downloading & running the pilot first utility to search for the missing/outdated drivers.

  MSI FX720/FX720DX drivers download 10, 8.1, 7, Vista, XP

  It does not resemble the divers Intel graphics have been updated in a long time.  You may go directly to Intel.

  Nancy O.

• 26.0 Firefox works do not correctly with Mac OSX 10.9.1. Text jumps from one side to the other spontaneously

  I used firefox on Mac computers for years. I am now under Maverick Mac OSX 10.9.1 and have major problems with sizing of text in windows and windows suddenly change size (much smaller) and jump on the left side of my desk. Apple does not support Firefox, so I can't get assistance on their part and Mozilla is impossible to contact them directly. Can someone please help with this problem?

  You can check the problems caused by a corrupt localstore.rdf file.

  • http://KB.mozillazine.org/Corrupt_localstore.RDF

  Reset the zoom of page on pages that are causing problems.

  • View > Zoom > reset (Ctrl + 0 (zero); 0 + Command on Mac)
  • http://KB.mozillazine.org/Zoom_text_of_web_pages

  Start Firefox in Safe Mode to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox/tools > Modules > appearance).

  • Do NOT click on the reset button on the startup window Mode without failure.
  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• Engineering of Netgear works do not correctly with iOS 10 or Mac Sierra

  NETGEAR genius App does not recognize that my R7000 on the network once I updated to iOS 10.
  Also on Mac Update for Sierra, the Netgear genius app crashes.
  In both cases, I deleted and reinstalled to correct, however, they continue to fail.

  Thank you all. The app update took care of the problem for me. If all goes well for everyone.

• Comparison of material works do not correctly with SMU-6548

  Hi all

  Recently, I have developed an application that accesses the memory of DUT using SMU-6548. I was able to load a vector file HWS and get the result as a 'good' or 'fail' based on the comparison of hardware.

  For some reason, the card PXI wrote in the address correctly, reads correctly but does not display the correct result for "number of errors in the sample. I can see the data you expect on an oscilloscope. At the same time the VI shows more than 0 sample error and therefore concludes that this device did not read what was expected.

  Please help solve this problem.

  
  

• / CD player works do not correctly with the door of Baldur

  I was playing a game of RPG of older CD called Baldur Gate, I never had any problem, my laptop is out of battery to reboot it back, goes to the game for a split second, then freezes, I've run a startup repair, which froze, I removed the disc, then it starts very well. I put the disc in, go play you and get a blue screen dark, as if the game started but could not. using the Task Manager, I unlock the mobile. Then I got the cd, put it in my other computer, and it plays very well. whenever I put this drive it freezes if I try to expore or play the disc. Help?

  Hello

  Step 1: Check if the problem persists in the clean boot state.

  From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".

  Reference:
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. click on start and then click Run.
  2. type msconfig and click OK.

  The System Configuration Utility dialog box appears.

  3. click on the tab general, click Normal Startup - load all services and device drivers and then click OK.
  4. When prompted, click on restart to restart the computer.

  Step 2: Also, look for error messages in the event viewer. If you find error messages after return the exact error message so that we can help you better.

  Measures to check the application event log:

  a. Click Start.
  (b) in the search box type eventvwr.msc, and then on enter.
  c. now, click Application in the event viewer (local).
  d. now, looking for event log on the right side of the event viewer window.
  http://Windows.Microsoft.com/en-us/Windows-Vista/open-Event-Viewer
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-information-appears-in-event-logs-Event-Viewer

• ALPS touchpad works do not correctly with Windows 8 dm4-2070us

  I upgraded to Windows 7 to Windows 8 on my laptop dm4-2070us, and now I have more use of gestures or scrolling on the Alps touchpad. The left and right buttons work and I can move the cursor anywhere on the screen, but that's all. Everything else seems to work fine. I can't find drivers anywhere for the Alps touchpad for Windows 8. All the world has noticed what is happening? I hope that a new driver will soon be developed but not optimistic. Any suggestions out there?

  Hello

  The ALPS Win8 dm4-2xxx pilot will be SP58700 and should appear on the ftp site, when it is released.  I have no ETA, but it should be soon.

  FTP://FTP.HP.com/pub/SoftPaq/sp58501-59000/

  Wes

• prompt of dashboard works do not correctly with the default values

  I created 2 dashboard:
  
  Dashboard 1 are:
  prompt A
  report A
  
  Dashboard 2 were:
  B invites
  report B
  
  Report A and B are the same reports as structure and filters. Only have different names.
  Prompt A and B both filtered region attributes:
  Invite a default view in clause sql on the "Région" attribute values: region1, 2, 3
  B quickly view sql clause on the "Région" attribute default values: 4, 5, 6
  
  If I run the A dashboard, it works fine.
  If I run the dashboard B, show me the same values of the dashboard (region1, 2, 3) in the two guests of report.
  If I click on the Clear button, the B dasbhoard runs correctly and shows 4, 5, 6 in the two guests of report.
  
  Seems to be something in the cache. But why?
  
  
  Sara
  
  Published by: Sara C. on 18 / gen/2010 9.41

  Go ahead and skip this step then. I never did, but my colleague has mentioned that you can disable the RPD to be cached at all, so if you are in online mode and you still cannot manage the cache, assume that this feature is disabled.

  In addition, as I said above, I don't think it is a caching problem, it was just more precautionary, so I don't think it will be a big problem.

  Please let me know how the rest goes!

  Kind regards
  Jason

  PS - Out of curiosity, what version of OBIEE do you use? 10.1.3.4?

• Photoshop works do not correctly with the graphics card.

  When I start the PS, he gave me messages while ensuring that I have updated graphics card drivers, what I'm doing. If I enable Open Gl drawing in Photoshop it does not open some documents or fails. If I disable the Open GL drawing, it opens the documents, but obviously is not giving me the display performance that I need. I've been running this setup for about 6 months, but only started having problems this week. I am running Photoshop CS4 and a nvidia GTX 295.

  Do not appear to have catastrophic graphics card problems (touch wood), I can always run Crysis!

  Can someone help me please?
  

  Are - what you happened to download the faulty Nvidia driver package which was listed so removed from the site? This package is defective and caused the Nvidia GPU down and turn into bricks. You wrote that you have just started to have problems, then maybe that's your problem. I would use an old driver until Nvidia it sorts.

• with firefox 43 yahoo and yahoo mail doesn't work does not correctly

  With the help of win 7 and firefox 43.0.1, I have 4 computers and now all have problems with yahoo and yahoo mail doesn't work does not correctly. Loading sites, but most of the features are missing and clicking on what whether changes to the lists of text. I have disabled flash / anti-spam etc., cleared cookies and cache and even firefox loaded down once again and have upgraded, no help. I'm forced to use IE now.

  I tried Yahoo support, they said try Firefox... In any case, it's Firefox and I found a solution using the 'Refresh Firefox' button. Whatever the problem was fixed on two of my computers so far. Got to update my setting again but it's 10 m, compared to the 10 hours I spent trying all that is nothing.

  Thanks for the help!

• Norton network adapter "Microsoft ISATAP map2" diagnostic reports works do not correctly-could not load the required device driver (code 31)

  Original title: System reports the NIC does not properly

  Using Vista Home premium on HP pavillion m8075a model RZ555AA-ABG. Norton network adapter "Microsoft ISATAP map2" diagnostic reports works do not correctly-could not load the required device driver (code 31)

  As none of the problems are met with connection network, do I ignore this warning or try to update the driver?

  Hi eucalyptussurfer,

  You can ignore this error message. This error message does not indicate a problem with the adapter. The adapter will continue to function correctly.

  Please see the following article:

  On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message

  http://support.Microsoft.com/kb/932520

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Why is one of my 4 5893 Modules doesn't work does not correctly?

  Hello

  This is the configuration of my HW and SW:

  LabView 2013 SP1

  1 x cRIO 9076

  4 x NI 9853 CAN Modules

  CAN0 - 1000 Kbps, entry timeout = 0, OutputTimeOut = 10000, Module clock: 20 MHz

  CAN1 - 500 Kbps, entry timeout = 0, OutputTimeOut = 10000, Module clock: 20 MHz

  I worked on a program for a test system, where each Module 9853 control two devices (CAN0 and CAN1), the same type of systems is controlled by other 9853 3 Modules in parallel.

  So basically, I use exactly the same functions for each module. So far, everything has worked correctly on module 1, but now that I started to test all other modules I have the problem that Module 3/CAN0 does not correctly read the information.

  While watching the FPGA façade, I see that each 10000ms one value is read, but only on that ONE module (frames are sent every 1ms from my unit)

  I tested the HW itself using the included examples and it works correctly, the only difference is that the example used only 2 Modules, one to send data and the other to receive it.

  I included my FPGA program as an image, I really don't think there is a problem with my RT SW, because all the other modules are working properly. Basically, my SW FPGA bed CAN Modules and puts the information in a FIFO, if there is an error (no information), it will make a loop once more and check again.

  Thanks for your help

  I solved the problem, it was an error of configuration on my side.

  The entry for Module3 CAN1 time-out was set up NOT as 0ms and 10000ms as I thought! , so that was my reading for DUT3 loop run only every 10000ms.