Begin the AAA Infrastructure with ISE
Hello
I configured Authc and Authz policy as follows:
Authc:
If Virtual Radius-NAS-Port-Type is equal to the default network access and use AD
Authz:
If Radius-NAS-Port-Type is equal to virtual
AND the specific AD user group
then the profile Authz permissions (Cisco av-pair = NCS:role0 = root and NCS: virtual-domain0 = ROOT-DOMAIN)
I am able to authenticate successfully and authorization authorization is applied and I can see what the authentication logs, but after that it seems what ISE goes back to politics of authentication by default to deny access.
Please someone explain why this failure as the premium Administrator's guide is not the correct configuration steps.
For my result of authorization in ISE for PI profile, I use the following syntax:
Access type = ACCESS_ACCEPT
Cisco-av-pair = NCS: virtual-domain0 = ROOT-DOMAIN
Cisco-av-pair = NCS:role0 = root
Now, you obviously need to change this, if you have several virtual domains in PI. It looks like what you use.
My successful connection is indicated below (however I do not see the virtual port type):
Timestamp of source | 2015-03-03 10:23:56.123 |
Receipt of timestamp | 2015-03-03 10:23:56.123 |
Policy Server | MYISESERVER |
Event | 5200 successful authentication |
Reason for failure | |
Resolution | |
First cause | |
Username | mycoolusername |
Type of user | |
ID of the endpoint | |
Profile of endpoint | |
IP address | |
Identity store | MYADIDENTITYSTORE |
Membership group | |
ID of Session verification | |
Authentication method | PAP_ASCII |
Authentication Protocol | PAP_ASCII |
Type of service | |
Network device | PISERVERNAME |
Type of device | Network management |
Location | Head office |
The IP address of the NAS | ADDRESS-IP-IP |
NAS Port ID | |
NAS Port Type | |
The authorization profile | Cisco-Prime-Infrastructure |
Status of the posture | NotApplicable |
Security group | |
Response time | 19 |
Try to take the port type = virtual in your authorization profile config. I only see the port type = virtual in authentication.
Tags: Cisco Security
Similar Questions
-
Cannot open the URL of the CWA with ISE
Hi people,
I have a problem when you perform the CWA with ISE so that I can give you access to the network for the guests.
Everything is fine except the URL of the CWA: when guests, open Explorer and enter a domain name after you have connected the SSID, they will be redirected to the URL like 'https://hostname.demo.com:8443 / guestportal /... ". " which begins with the hostname of the ISE and the domain name of the ISE, but for us, we have not any announcement and the LAN DNS for our network so that we cannot translate the hostname.demo.com in the IP address of the ISE, so can I just change the URL type of intellectual property like"https://10.10.10.70:8443 / guestportal?
Screenshot of an attached screenshot (sorry).
Basically it's in the authorization policy, allows you to use a static DNS or IP address
-
Need help with the configuration of the AAA
I try to configure AAA on my network devices. I use GANYMEDE + with an ACS (3.2) server. I have groups of users of installation against two in the ACS, 1 voice server and allow privileges and the other without. I am able to get the AAA configuration to work when telnet in devices. However, when you connect in the port of the console, the user with privileges to activate Group do not go directly in the activation of the mode as do the users of telnetted. How to solve this problem?
Hello
You should not use the following command: -.
authorization AAA console
This command will not be displayed on the help.
Kind regards
Vivek
-
Evaluation of posture before logon - possible with ISE?
Does anyone know if it is possible (or not) to have a machine postural windows valued at startup? That is to say. until someone connects to this topic. Currently I have to connect to my machine before the start of the assessment. It would be good to have assessment begins as soon as the machine starts while (assuming the machine passes assessment) it is completed by the time wherever I am. We use the NAC Agent with ISE1.2.
Thanks in advance for your ideas.
AFAIK, the agent of posture is no nothing until the user is connected, I never saw a report of position at ise, that indicates anything about it either, because you would get many posture compliance checks failed, if she did (audit of key, user, av status files and so on in the land of the machine).
-
The NAC Agent autoUpgrade ISE possible?
Hi all
I have this:
802.1 x-window with the NacAgent version (say 1) <---->802. 1 x switch active (RADIUS aaa OK) <------>ISE and AD on the same LAN
ISE is configured for client provisioning with hardware (NacAgent version 2) downloaded from Cisco's Web site (as described in the documentation)
I have a basic plan of authentication and authorization that allow me to well but I expect the NACAgent to be upgraded.
No profiling is configured at the moment.
Is that someone can help?
Best regards?
Hello
In the ISE settings provisioning client, activate you the option where the NAC upgrade agent is required. However, it is to you to run updates perioidic and map the most recent agent in the configuration of the parameters of the client.
Thank you
Tarik Admani
------>---->
* Please note the useful messages *. -
Firefox instructions for using a link in the email to send large attachments came when I was preparing to do so in the email. Sounds good to me, but the instructions beginning with by clicking on the "Firefox" button on the upper left corner. I don't have one. I've updated the software but still no button. The Firefox on my lap top has this button. I use the laptop for classes. All the rest is with my PC.
Why have I not the button, and how to do it there? I use Windows 7 on all my computers except of on my iPad.
Right click on a zone empty of the tab bar and uncheck "menu bar".
-
I would love to see my idea of ISEEDS Apple. Wireless. Bluetooth headsets in the form of seeds. No more son. And they simply slide to the back of the phone. They are always charged. A simple click of your thumb at the back and an iseed movies out. And an Apple healthy seeds
Garry Graham
Please you not to Apple here. This is a user forum. You can share your comments with a Apple. They will not respond, but at least they'll know your suggestion.
-
I use PyDAQmx with a USB-6363, but I think the question is generic to DAQmx.
I have an output buffer that I want to be able to (re) write to without starting the task output.
More specifically, I have a graphical interface and a few sliders, the user can move. Whenever the slider changes, a new set of values is loaded into the buffer output through DAQmxWriteAnalogF64. After you set the value, the user can click on a button and start the task output.
In some cases the change in cursor does not require a change in buffer size, only a change in the data. In this case, I get the compalint following DAQmx as they tried writing:
The generation is not yet started, and not enough space is available in the buffer.
Set a larger buffer, or start the generation before writing data more than content in the buffer.
Property: DAQmx_Write_RelativeTo
Value: DAQmx_Val_CurrWritePos
Property: DAQmx_Write_Offset
Corresponding value: 0
Property: DAQmx_Buf_Output_BufSize
Corresponding value: 92In other cases the change in cursor requires both change in the size of the buffer and data modification. In this case, I get the following, but only after that do a few times each time increase the size of the writing.
DAQmx writing failed because a previous writing DAQmx configured automatically the size of output buffer. The size of the buffer is equal the number of samples written by channel, so no additional data can be written before the original task.
Start the generation of before the second writing DAQmx or set true in all instances of writing DAQmx Auto Start. To gradually write to the buffer before starting the task, call DAQmx Configure an output buffer before the first writing DAQmx.
Task name: _unnamedTask<0>State code:-200547
function DAQmxWriteAnalogF64I tried to configure the output via DAQmxCfgOutputBuffer buffer (in some cases, by setting it to zero or a samples, then save again, in an attempt to clear it) but that doesn't seem to do the trick.
Of course, I can work around the problem by loading data only when the user clicks the end button, but not what I'm asking here.
Is it possible to "remake" the writing of output before you begin the task?
Thank you
Michael
Today I have no material practical to validate, but try unreserving task before writing the new buffer:
DAQmxTaskControl (taskHandle, DAQmx_Val_Task_Unreserve);
With a simulated device, he made the error go away in case the buffer is the same size. You will need to validate if the data are in fact correct, but I think it should be (unreserving I would say reset the write pointer so the old buffer are replaced with the new data).
I always get errors when you try to change the size of buffer if (on my 6351 simulated). I posted some similar mistakes about the reconfiguration of the tasks here, I guess it is possible that this issue has also been set at 9.8 (I always use 9.7.5 on this computer). If the behavior is still present in the new driver, and also appears on real hardware (not just simulated), then it seems that this is a bug of DAQmx someone at OR should be considered.
I wrote a simple LabVIEW VI that captures the error in order to help people to NOT reproduce it:
The best solution at the moment would be likely to re-create the task if you need to change the size of the buffer (or avoid writing data until you are sure what will be the size of buffer).
Best regards
0> -
measurement of voltage battery pinout 1.5 V AAA DC with acquisition of data USB-6009
Hello, I have a very basic question with pinout when measuring 1.5 V voltage on a USB DAQ 6009, using an AAA battery. Is it okay to connect (+) to AI0 and (-) to such AI4 suggested in MAX?
Nothing else required?
(attached pinout)
Thank you
Hi feanorou,
Yes, you have the Terminal configuration as award-winning, then using the 0 pine as AI (GOT 0 +) and using PIN 4 HAVE (I - 0) is a good setup for measuring the AAA battery.
-
Unable to connect to the PPPoE server with 2 BEFSR41ver
I had to get a new AT & T DSL line to a new home with new ID and password. I've never had a problem with the router to the old address and the line DSL. I've reconfigured the router with a new user name and password for PPPoE I got from AT & T for use with their new motoroal they sent me. The modem gives me the internet when I connect the modem directly to the computer. When I connect the modem to the WAN port of the router with the computer connected to one of the LAN ports on the router, I get "Unable to connect to PPPoE" when I try to access the internet. When I connect the modem to one of the LAN ports with another port LAN from the router to the computer, I don't have the internet, but this is not recommended for the router cable management. With the modem connected to the WAN router and a power cycle performed port, I still get the same error message. I disabled my firewall and still have the same error message. I don't think I have another firewall to operate. I never had this problem to my old address and line DSL AT & T with different ID and password and the same router. Anyone know what is happening? STEIN
Your problem is that your "modem" is actually a "modem-router" and it uses the same subnet as the BEFSR41 192.168.1.x. To resolve this issue, follow these steps:
All first, reset your BEFSR41 factory default, then set the "local IP address" 192.168.2.1
To do this, follow these steps:
To reset your router by default, follow these steps:
(1) turn off all computers, the router and the modem and disconnect from the wall.
(2) disconnect all the wires of the router.
(3) turn on the router and let it start up completely (1-2 minutes).
(4) press in and hold the reset for 30 seconds button, then release it, then let the router reset and restart (2-3 minutes).
(5) turn the router.
(6) connect a computer cable to port 1 of the router (NOT to the internet port).
(7) turn on the router and let it start up completely (1-2 minutes).
(8) the power of the computer (if the computer has a wireless card, make sure it's off).
(9) try ping on the router. To do this, click the 'Start' button > all programs > Accessories > command prompt. A black DOS window will appear. Enter the following text: "ping 192.168.1.1" (without the quotes) and press the Enter key. You will see 3 or 4 lines that begin with ' response to... ". "or"Request timed out". If you see "reply from...". ", your computer has found your router.
(10) open your browser and point it to 192.168.1.1. This will take you to the login page of your router. Leave the user name blank and in the password field, enter "admin" (without the quotes). This will take you to your router configuration page. Note the version number of your firmware (usually found near upper right corner of the screen). Then, change the "local IP address" 192.168.2.1, then click the 'Save Settings' button and wait (3 to 60 seconds) of the screen refresh. You will be probably disconnected from the BEFSR41. Don't worry about this. Turn off the BEFSR41 and your computer.(11) then, using an ethernet cable, wire the ethernet port of the modem to the Internet port on the BEFSR41. Turn on your modem and enable good start. Turn on your BEFSR41 and enable good start. Turn on your computer. Test your system, it should work.
If you can not ' response to... ". "in step 9 above, your router is probably dead. Report with this info.
If you get a response in step 9, but cannot complete step 10, is that your router is dead or the firmware is damaged. In this case, a report with this problem.
If you need additional assistance, please state the version of firmware on your router and the results of steps 9 and 10. In addition, if you receive error messages, copy them exactly, and report.
Please let me know how things turn out for you.
-
Downloaded some updates which has increased my hard disk activity, which has me concerned. I went to the restoration of the system to use my laptop for the last restore, point before downloading. And now I have the system questions without error code of restore, hard boots fine except message saying that the system restore did not complete. I'll look forward all help! Thanks in advance!
Hello
There are a variety of reasons for system restore problems
Norton and Norton product Tamper Protection is the main
Read about it:
http://us.Norton.com/support/kb/web_view.jsp?wv_type=public_web&docURL=20101101224849EN&LN=en_US
http://Service1.Symantec.com/support/sharedtech.nsf/pfdocs/2005113009323013
You can try restoring the system in safe mode
http://www.windowsvistauserguide.com/system_restore.htm
Windows Vista
Using the F8 method:
- Restart your computer.
- When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
- Select the Safe Mode option with the arrow keys.
- Then press enter on your keyboard to start mode without failure of Vista.
- To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
- Do whatever tasks you need and when you are done, reboot to return to normal mode.
and malware can interfere with the restoration of the system
Download update and scan with the free version of malwarebytes anti-malware
http://www.Malwarebytes.org/MBAM.php
You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes
http://www.bleepingcomputer.com/download/anti-virus/rkill
If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking
Windows Vista
Using the F8 method:
- Restart your computer.
- When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
- Select the Safe Mode with networking with the arrow keys.
- Then press enter on your keyboard to start mode without failure of Vista.
- To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
- Do whatever tasks you need and when you are done, reboot to return to normal mode.
-
ASA 5525 X Anyconnect configuration with ISE 2.1
I have a new deployment of ISE 2.1 which is used only for the management of the devices at the moment. The intention is that it will serve as radius for authentication of our VPN server.
5525 x is a brand new ASA runs the 9.4 code. I want to configure VPN on the SAA strategy so that each user is assigned a DAP based on their Department.
I already have the designation of the Department for user accounts assigned in AD through a group membership. I don't know how to get ISE to belonging to a group at the ASA so that she can associate the user based on this correct in RAP group membership.
I succumbed to determine how this is supposed to work. Thanks for any help.
Normally we authenticate and authorize users and then push DACL or allow connection from ISE etc. of such conditions profiles that check results Posture or parts constituting the identity of the user (such as AD or another external identity store belonging to a group).
There are a couple of good guides to do so, including detailed examples:
https://communities.Cisco.com/docs/doc-68158
http://www.Cisco.com/c/en/us/support/docs/security/Adaptive-Security-app...
http://www.Cisco.com/c/en/us/support/docs/security/AnyConnect-secure-mob...
While they focus on the case of use of Posture, they can be adapted to add other uses. For example, ISE registration condition may be the result of not only a Posture check also membership in a given group or another if you make it a State.
I do not think we can specify to the ASA to call a given font of DAP like Hostscan module cannot be used at the same time that the module ISE Posture. However, you should be able to accomplish just about everything you used to depend on the DAP with ISE Posture Module AnyConnect (assuming you have AnyConnect 4.x Apex licenses).
If you want to stick with the ASA DAP model, you can forgo using policies and module ISE Posture and instead create an authorization profile (result) to send the ASA, a pair of RAY - V based on a correspondence (in the authorization of the ISE policy) with the ad group. He is a "Cisco-VPN-3000" A - V called "PIX7x-members-from' that can be used in ASA dynamic access policies. You can see (and all other pairs A - v supported buy ISE) here:
-
UNMANAGE an access point light on the MAIN Infrastructure
Hi guys,.
is there a way to unmanage a lightweight AP (LAP) on the Cisco Infrastructure FIRST, but keep it on the WLC management?, we want some of the life cycle free licenses.
Currently, we have a problem of license because when we add a WLC FIRST automatically adds all of its associated towers (115 aprox.) and they consume almost all lifecycle licenses available (125), causing that we cannot add another 10 aircraft for their FIRST management.
Is it possible some of these tricks FIRST unmanage but to keep their management of their corresponding WLC (in order to free some licenses of life cycle)?
Thank you in advance!
Kind regards
Sorry, but only you can do.
Once you succeed a WLC, all its associated with APs are also managed and therefore consume licenses of life cycle.
-
The AAA for PIX515E 6.3 rules (5)
Hello. If I wanted to configure the PIX for the authentication of an ACS server (for the purpose of management of PIX), what else would need apart from what follows:
AAA-server Admin-FW Protocol Ganymede +.
AAA-Server Admin-FW max-failed-attempts 3
AAA-Server Admin-FW deadtime 10
!
AAA-Server Admin-FW (inside) host 192.168.2.9 access timeout 10
!
console series FW-Admin-AAA authentication
Console telnet authentication AAA Admin-FW
authentication AAA ssh console Admin-FW
As far as I KNOW, I did not specify which IP addresses can someone telnet from to connect on the PIX. I tried the following, but I do not know I did not provide the correct instructions:
the AAA authentication include telnet inside 192.168.0.0 255.255.0.0 Admin-FW
... and I have a username / password to invite him on the PIX but it keeps asking for a user name and password. I know my account GANYMEDE is good because I can connect on the routers with the same details as what I use to authenticate on the PIX.
I also ran a debugging on the PIX when I was trying to authenticate. The output is attached.
Thank you
Timothy
Hi Tim,.
There is no need to order,
the AAA authentication include telnet inside 192.168.0.0 255.255.0.0 Admin-FW
Try it now and see if you get hits on ACS. Incase it is not working, pls get again him debugs.
Thank you
Jagdeep
-
Authentication RADIUS with ISE - a wrong IP address
Hello
We use ISE for radius authentication. I have setup a new Cisco switch stack to one of our branches and set up the device network in ISE. Unfortunately, in trying to authenticate, ISE logs show a lack of "Impossible to locate device network or Client AAA" the reason for this failure is that the log shows that it comes from a bad IP address. The IP address of the switch is 10.xxx.aaa.241, but the logs show that it is 10.xxx.aaa.243. I removed and added the configs of RADIUS on ISE and the switch, but it is always so que.243. There is another switch battery location (same model, IOS etc), which works correctly.
The config of RADIUS on the switch:
AAA new-model
!
!
AAA authentication login default local
AAA authentication login Comm group local RADIUS
the AAA authentication enable default
RADIUS group AAA authorization exec default authenticated ifradius of the IP source-interface Vlanyy
10.xxx.yyy.zzz RADIUS server
10.xxx.yyy.zzz auth-port 1812 acct-port 1813 ipv4 address
abcdefg 7 keyThe journal of ISE:
Overview
5405 RAY lost event
Username
ID of the endpoint
Profile of endpoint
The authorization profileDetails of authentication
Source Timestamp 2014-07-30 08:48:51.923
Receipt 08:48:51.923 Timestamp 2014-07-30
Policy Server ise
5405 RAY lost event
11007 failure reason could not locate device network or Client AAA
Resolution check if the device network or AAA client is configured in: Administration > network resources > network devices
Root cause could not find the network device or the AAA Client while accessing NAS by IP during authentication.
Username
Type of user
ID of the endpoint
Profile of endpoint
IP address
Identity store
Membership group
ID of Session verification
Authentication method
Authentication Protocol
Type of service
Network device
Type of device
Location
10.xxx.AAA.243 address IP NAS
ID of Port NAS tty2
Virtual NAS Port Type
The authorization profile
Status of the posture
Security group
Response timeOther attributes
ConfigVersionId 107
Device port 1645
DestinationPort 1812
Radius protocol
NAS-Port 2
AcsSessionID ise1/186896437/1172639
IP address of the device 10.xxx.aaa.243
CiscoAVPairMeasures
Request for access received RADIUS 11001
11017 RADIUS creates a new session
11007 could locate no device network or Client AAA
5405As a test, I set up a device that uses the adresse.243. While ISE claims that it authenticates, it really doesn't. I have to use my local account to access the device.
Any advice on how to solve this problem would be appreciated. Please let me know if you need more information.
Beth
Remove your (RADIUS-server host 10.x.x.x... ect) tele-health and try this command and see if the problem goes away. The new section is the non-standard expression allows to see if that helps.
RADIUS-server host non-standard key of acct-port of the auth-port 1645 10.xxx.xxx.xxx 1646 *.
Maybe you are looking for
-
WD Passport Studio permissions on custom and cannot be changed
I have a drive hard 2 TB WD Passport Studio external for backup purposes. I set the permissions using a MacBook Pro I have more have and am not able to access my backups and files with my new MacBook Pro. How to reset the permissions so I can access?
-
Help to change the toner in my HP printer
Original title: change the toner How can we change the Color LaserJet CP1025nw printer toner
-
Since Windows 7 Starter to Windows 7 Professional
Can I go directly to Windows 7 Professional to Windows 7 Starter?
-
Cannot delete a backup.
I can't delete this backup on a DVD + R disc, I na not complete the backup because I wanted to save it on a USB key. How can I delete the backup? They are 2 discs. Their is no button Delete, cannot be moved to the trash.
-
HP J4680 all in one does not print anything in black
Equip the new hp black cartridge but printer will not align... and then, it will not print color as black. So I tried an another new black print cartridge and the same thing happened. I do again a new printer or is there a fix.