Beginner needs help loading Quick Books

Similar Questions

• Flash beginner needs help with Movie Clips/Action script

  HI -.
  
  I'm having a problem with my video clips playing simultaneously and cannot, for the life of me, know what I did wrong. I'm new to flash so I can I have created something wrong but this is what I have so far:
  
  11 layers, total: 1 layer with 10 buttons, each button with the following actionscript code:
  
  
  on (release) {}
  gotoAndPlay (85);
  }
  
  
  When the number changes with regard to keyframes, the next film is about.
  
  I have 10 films, total, but they are only video clips, mainly photo slideshow with audio, does everything in the library.
  
  The problem occurs when I click on the second or third button. Not only the movie I selected starts to play, but all previous clips are as well, he has completely blurred all the sounds. I don't know what Miss me in action script, as my Action layer has a stop command to this topic at each keyframe where there is a new clip to play.
  
  I tried to add a stopAllSounds command, but I'm afraid that does nothing because it is not an "audio file" in itself playing in the timeline panel.
  
  I'm at the end of my rope and really need help to understand this one. My project is hanging in the balance on this point, I wrote everything correctly and it works beautifully.
  
  Help, please!
  
  Thank you
  Caroline

  Start your sounds in frame 2 and place stopAllSounds() on each keyframe where begins a movieclip.

• BlackBerry smartphones HELP Please I need help! QUICKLY:'(BLACKBERRY BOLD 9900)

  Hi all

  Seriously I need your help fast!  Im going first on Saturday and my Blackberry Bold 9900 won't turn on!  A few days ago my Blackberry battery emptied very quickly! I used to charge it all night and then when I woke up it's only 3/4 battery left! STRANGE! But anyway, then I when I went to school I texted my classmates that I am at school. I used to put my phone in to school. And when I got out, I discovered a STRANGE surprise! My phone would not turn!  Very well, I came home and I loaded all day well nearly! I'm used to it until today. A with my mated said because I load it too much on the night and a blackberry takes about 3 hours to recharge, it can . So I loaded the morning. I had 1/4 left! So I've dealt with him and went to school. When I arrived home and are charged my phone it not light. So yes it died completely! As always.  But then I left it loads for a time came it turned on and the red LED flashes. So I left up to now to load, but when I try to start the same thing is happening that shows a red LED! I took out the battery and waited 10 seconds, but still nothing happens! PLEASE

  I ONCE HAD A REQUEST THAT I THOUGHT CAUSED THE PROBLEM I REMOVED IT TUESDAY RESTARTED THE PHONE AND NOTHING HAVEN'T CHANGED SINCE THEN, PLEASE HELP ME!

  Hello and welcome to the community!

  Please try this sequence... Note that, throughout the whole 4h15m process, your BB should stay connected to a good charger (not the USB PC):

  1. With battery, connect your BB to the wall charger
  2. Leave it alone for 2 hours, no matter what the LED or the screen not
  3. Remove the battery
  4. Wait 15 minutes
  5. Insert the battery
  6. Wait another 2 hours, no matter what the LED or the screen not

  This has been known to "revive" some BBs.

  It is also possible that your battery or BB has encountered a problem... to test, this sequence is necessary:

  1. Get a known good and already fully charge battery... use it in your BB and see what happens
  2. Get access to a BB good and the same known... use your battery in there and see what happens

  The results of this will show if your BB or your battery that has the problem.

  Good luck and let us know!

• Help load audio books

  Hi all

  I'm sure that it took more than 1000 times, but I still do not understand this...

  What I want to do is to load an audio book, as he will play in the order, i.e. when disk 1 is finished then start playing the disc 2, etc..

  I have years of experience in computer science, have tried to use mp3tag, Media Player, monkey media, all I can think about, but it still doesn't work.

  For example, suppose I have an audio book with 2 discs... can someone walk me through what I need to do? Or perhaps point me to a tutorial?

  Thank you

  Victor

  RIP the disks for mp3 files. IMO, it's better to tear the creations oral files mp3 32 kbps mono to save space on the drive. IMO 32 kbps mono mp3 sounds pretty well, and using higher throughput not incease its good quality. For music I use 256 Kbps.

  After extraction of discs, the first disc of mp3Tag I open and use mp3 tag to put in the right order. So I would like to use the autodial feature in taf mp3 count starting with 101 so I a the beach 3-digit number. Start numbering at 101 allows up to 899 titles for the book using a tag 3-digit and eliminates the need for leading zeros in the track number.  Then I opened up the second disc, renumber the tracks starting with the next number after a final in the first disc. Then I would change the tag of the album for the files in the second disc so that it matches the first disc. Then I would merge the files second disc first. The next albums would be treated in a similar way.

• Beginner needs help

  can I use microsoft security essentials and windows defender at the same time? If not what shoul I run the more or is - it possible to run antivirus and windows defender at the same time?

  Hello

  Windows Defender features are included in MSE, defender of loading would be redundant.

  Windows Defender antispyware =

  MSE is antivirus + antispyware.

  Then think about MSE as Windows Defender with more added (which is).

  ===========================================

  Here's what I use and recommend:

  Avast and Prevx proved extremely reliable and compatible with all I have
  launched on them. Microsoft Security Essentials and Prevx have also proven to be very
  reliable and compatible. Use MSE or Avast and Prevx, Prevx 3 but not all.

  Avast Home free - stop any shields is not necessary except leaving Standard, Web, and
  Operation of the network.

  Prevx - Home - free

  Windows Firewall

  Windows Defender (is not necessary if you use MSE)

  Protected IE - mode

  IE 8 - SmartScreen filter WE (IE 7 phishing filter)

  I also IE always start with asset if filter InPrivate IE 8.
  (It may temporarily turn off with the little icon to the left of the + bottom
  right of IE)

  Two versions of Avast are available 5.x and 4.8 x

  Avast - home - free - 5.x stop shields you do not use (except files, Web, network, &)
  Shields of behavior) - double click on the icon in the Notification area - real time Orange - click on the
  Shield that you want to stop - STOP. To stop the Orange icon to show an error indicator-
  Click on the Orange icon - top right - settings - click on the status bar - uncheck shields you
  disabled - click OK
  http://www.avast.com/free-antivirus-download

  Avast 4.8 x - home - free - stop shields, you don't need except leaving Standard, Web,.
  and the network running. (Double-click the blue icon - look OK. - upper left - Shields details
  Finish those you don't use).
  http://www.avast.com/free-antivirus-download#TAB4

  Or use Microsoft Security Essentials - free
  http://www.Microsoft.com/Security_Essentials/

  Prevx works well alongside MSE or Avast

  Prevx - home - free small, fast, exceptional protection CLOUD, working with other security
  programs. It is a single scanner, VERY EFFICIENT, if it finds something come back here
  or use Google to see how to remove.
  http://www.prevx.com/   <-->
  http://info.prevx.com/downloadcsi.asp  <-->

  PCmag - Prevx - Editor's choice
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  Also get Malwarebytes - free - use as scanner only. If you ever think malware and that
  would be unusual with Avast and occasional Prevx running with the exception of a low level cookie
  (not much), to UPDATE and then run it as a scanner. I have a lot of scanners and they
  never find anything of note that I started to use this configuration.

  http://www.Malwarebytes.org/

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• BlackBerry 10 need help to quickly insert a lot of inserts/Word sub to the many BB features

  Hello. Please help if you know ways to do this.

  I need a way to insert a large number of inserts of many devices of BB quickly on BB OS 10.
  I use dozens of BB Phone for my business, and I use hundreds of AutoText to meet my clients. Also it is not possible to manually insert/Enter AutoText one by one in every phone.

  In blackberry OS 6, I just restore the data and choose AutoText to insert my automatic backup to new phone. But on BB OS 10, it says legacy files are not supported.
  I also try to do a backup on BB 10 phone to copy inserts, but when restoring to another phone (for copy insertions), it must be in the same ID of BB.
  What is another way to help me to insert these inserts to other phones other than by using the manual method (input a)?

  Thank you

  None that I know. There is no party 3rd backup/restore of insertion is.

• Need HELP loading and unloading SWFs external when the user clicks on the buttons

  Hi everyone, I'm working on a few Web sites at the moment, one for being my online portfolio, as well as my Web site for a product of sleep, that I'm selling.  I have very little experience with AS3, last time I created a Web site that as2 has been used.  I tried a few tutorials online, but nothing performs the work, there is always an error...

  I have an index.swf that loads the default home.swf.   There is also an about.swf, contact.swf, order.swf and testimonials.swf...

  It was a hair pulling 4 days now, not be able to get this working.

  All I need is for the swf external to pull up when you click on the corresponding button, and when the next button is clicked, the current to unload swf and swf to load new file.  It was so simple with AS2, you would think things could be as easy, if not easier.   So any help that all the world can offer, I would be so very you happy for me!  If necessary I can copy my current code, even if it doesn't work!   Thanks, Mike

  var loader: Loader = new Loader();

  addChild (loader);

  home_btn.addEventListener (MouseEvent.Click, loadF);

  about_btn.addEventListener (MouseEvent.Click, loadF);

  contact_btn.addEventListener (MouseEvent.Click, loadF);

  function loadF(e:Event):void {}

  Loader.Load (new URLRequest (e.currentTarget.name.split ("_") [0] + ".swf")); / / assuming that each reference button is also the button's name property

  }

• still need help loading:(en dehors de fichiers en actionscript)

  Ive been all over the forums online trying to get this fixed a problem and nobody has really solved for me (its been MONTHS)
  So I'll try to be as in depth as possible and post code as well.
  Here's the deal-it's a portfolio site, www,darrenlasso.com
  The problem is when I load several swf files into levels. When I call first on an external swf by a button inside the master the code looks like this:
  
  {We (Release)}
  _level1._visible = false;
  loadMovieNum ("cover.swf", 1);
  cvrbtn._visible = false
  acibtn._visible = false
  
  }
  
  When to go inside THIS file, I want to go back to the MAIN navigation file, the code looks more like this:
  
  {We (Release)}
  
  mcl.addListener (mclListener);
  
  
  mclListener.onLoadInit = function (mc:MovieClip) {}
  MC._visible = true;
  mc.gotoAndPlay (76);
  }
  
  _level1._visible = false;
  mcl.loadClip ("darnen.swf", 1);
  }
  
  Ive has messed around with the code so many times now, try different suggestions that I don't even know if this is the code I live right now but I know that his doesn't work how I want it to everyone. The problem seems to be that I can load only in level 1, and when I do that, go between these different calls on files outside it is a "flicker" of a frame or two of the OLD file previously loaded who will play in front OF the initiates a new. As it is a portfolio site, it must be polite, so I can't have stuff like that which he suffers. Its been unfinished for months because I just can't understand it. Please please help me if you can... I hope you like a challenge because it's fair, I was not able to get the help that I need anywhere else :/

  If you want to view a specific frame in the SWF in _level0 and unload _level1, you can use:

• Beginner needs help with SimpleReadWrite

  After reviewing the NI-488.2\Examples\DotNet3.5\SimpleReadWrite\vb (which works fine) in "step" mode I can not yet discover the command which

  sends information on the device string. If I declare: BoardID As String = "0" Dim, Dim PrimaryAddress As String = "13", Dim SecondaryAddress As String =

  '0', Command1 dim As String = "* IDN?" what comes after?. Is this the right approach? What else do I need to know, and where and how I can find it?

  You did not add the assemblies to your project references list, as I have indicated in my note at the end of my answer lat. This is done through the project-> add a reference... menu item. Be sure to select the assemblies that are located in the folder of VS2008, where you have installed the support for multiple versions of .NET. This is distinct from the required Imports instructions. The Imports statement allows to simply do not have to write the full name of the class. So, having a NationalInstruments.NI4882 import you can declare a variable as

  GpibDevice private as a device

  instead of the full name

  Private GpibDevice As NationalInstruments.NI4882.Device

  What about the ReplaceCommonEscapeSequences error, well, you actually have this function in your form. This copy of the SimpleReadWrite example function.

  You should check that your device is expected for the command. Require a carriage return after the order? Require a line break? If so, you must change the definition of Cmd1 to include these characters, as is done in the SimpleReadWrite example.

  TesTech wrote:

  I will surely find a tutorial or take a book to learn more about VB.NET, as soon as I can get this thing going.

  It's just to make life 100 x harder for you. The above errors would have been clear, if you knew how to program in VB.NET.

• ASA550 VPN works do not, Cisco beginner needs help!

  Hi people,

  I have to spend at Cisco Juniper, and I can't get a VPN. I tried hollow CLI and ADSM, and in both cases, I don't see any incoming ipsec packets on the other end (Juniper SSG) when I ping a remote host on the other network.

  Here is the config:

  !
  ASA Version 9.0 (1)
  !
  gw hostname
  activate 7qkORHwefwefwefwefyAiVSEQH4Q encrypted password
  7qkORHywefwefwefwefSEQH4Q encrypted passwd
  names of
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 172.16.1.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP address dhcp setroute
  !
  passive FTP mode
  network obj_any object
  subnet 0.0.0.0 0.0.0.0
  network of the SDC_Beheer object
  10.104.0.0 subnet 255.255.0.0
  access extensive list ip 172.16.1.0 outside_cryptomap allow 255.255.255.0 object SDC_Beheer
  access extensive list ip 172.16.1.0 inside_access_in allow 255.255.255.0 object SDC_Beheer
  inside_access_in of access allowed any ip an extended list
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  !
  network obj_any object
  NAT dynamic interface (indoor, outdoor)
  inside_access_in access to the interface inside group
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  the ssh LOCAL console AAA authentication
  Enable http server
  http 172.16.1.0 255.255.255.0 inside
  Server SNMP location Bergen op Zoom
  Server SNMP contact Joris Kemperman
  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
  Crypto ipsec transform-set esp - esp-sha-hmac DESSHA1 ikev1
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
  Crypto ipsec pmtu aging infinite - the security association
  card crypto outside_map 1 match address outside_cryptomap
  peer set card crypto outside_map 1 5.200.1.5
  card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_map interface card crypto outside
  trustpool crypto ca policy
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  authentication crack
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 20
  authentication rsa - sig
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 30
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 40
  authentication crack
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 50
  authentication rsa - sig
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 60
  preshared authentication
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 70
  authentication crack
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 80
  authentication rsa - sig
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 90
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 100
  authentication crack
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 110
  authentication rsa - sig
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 120
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 130
  authentication crack
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 140
  authentication rsa - sig
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 150
  preshared authentication
  the Encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH 172.16.0.0 255.255.0.0 inside
  SSH timeout 60
  Console timeout 0

  dhcpd dns 8.8.8.8
  dhcpd lease 3800
  dhcpd field lindebaan73.local
  dhcpd outside auto_config
  !
  dhcpd address 172.16.1.30 - 172.16.1.157 inside
  dhcpd allow inside
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  internal GroupPolicy_5.200.1.5 group strategy
  attributes of Group Policy GroupPolicy_5.200.1.5
  Ikev1 VPN-tunnel-Protocol
  joris AewHowjZEPeq.vge encrypted privilege 15 password username
  tunnel-group 5.200.1.5 type ipsec-l2l
  tunnel-group 5.200.1.5 General-attributes
  Group - default policy - GroupPolicy_5.200.1.5
  IPSec-attributes tunnel-group 5.200.1.5
  IKEv1 pre-shared-key D1nges!
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:2498ca347e17bcfa3a8a5ad9968e606c
  : end

  ______________

  I think its either a NAT problem (ASA no tunnel traffic but simply translated and passed to the next router) or access list number.

  It already took me a lot of time to spend on what goes wrong.

  Anyone here who can help me?

  Hello

  You need to do no. NAT for the subnet you want to go through the tunnel.

  Thus, to create a group of objects to destination as source allows src1 and dest 1

  NAT (inside, outside) source static/dyn src1 CBC 1 destination dest1 dest1.

  For more information:

  https://supportforums.Cisco.com/document/44566/ASA-83-NAT-exemption-exam...

  Kind regards

  Kanwal

  Note: Please check if they are useful.

• PIX 501 config probs - beginner needs help!

  Have a bit of a nightmare trying to set up external access to one of our servers through the pix. He is currently in its factory config.

  I tried assiginig an Acl to allow the remote desktop on port 4999 from outside, but it doesn't seem to work. I have attached the config in its current form - please help this is driving me crazy!

  1.) basically the NAT public IP address to a private IP address is on the right of ADSL router. Check that!

  ADSL Public IP TCP 4999 to PIX outside TCP 4999

  (2.) the config on the PIX should be good, as I posted it.

  Redirect port of PIX outside IP TCP 4999 inside private IP TCP 4999

  3.) make sure that your server meets the port TCP 4999 really!

  On windows or Unix =

  netstat - year

  You should see something like this:

  TCP 10.0.0.3:4999 0.0.0.0:0 LISTENING

  4.) another way of troubleshhot might be using "capture" on the PIX. This like tcpdump UNIX a sniffer that can show packets on an interface. I do not remember what version, this command was introduced, but you will need at least an OS PIX 6.3.x to have.

  Example:

  access-list 120 permit tcp any any eq 4999

  capture of 4999 interface 120 outdoor access list

  See Access Snapshot 4999 list 120 retail

  To use remove:

  no interface access-list 120 captures 4999 out

  No capture 4999

  Change inside interface:

  capture of 4999 interface 120 of inside access list

  See Access Snapshot 4999 list 120 retail

  sincerely

  Patrick

• Need help to quickly create an analysis with PTD, QTD, CDA options the balance using option to change the formula

  I created the analysis report which has-

  -Opening balance

  -L' period activity

  -Closing balance.

  Now, the activity of period can be a. period to Date, quarter to date and year to date.

  I have PTD and QTD values... YTD will be calculated field = (ball Beg + period activity)

  Now, I want to add guest user that allows the user to select either - 1. PTD, QTD or CDA

  and report displays analysis accordingly.

  I need instructions to - how to add this in the prompt controls and criteria - to make it work according to the value of the parameter to create analysis

  Wait response

  SS

  Hello

  You can try this link below to view the report based on the quick selection.

  http://bihub.blogspot.in/2013/07/OBIEE-11g-display-multiple-reports.html

  Thank you

  Prasanna

• Need help coding Coloring Book App in AS3

  Hello

  I'm working on a project for school and I'm having a lot of trouble at the moment. I can't figure out exactly how to start coding for a coloring book type app. I read through about 6 different tutorials for this type of project, and can't seem to get anything to work for me.

  I drew the outline of the image, I want to be colorable and converted the outline into a symbol. I also have each separated colorable, it's own symbol as well. In total, I have 67 different colorable areas + contour. I've created a palette of colors for the user to select institutions.

  When it comes to coding for all this work, I'm completely lost. If someone could help me get started and point me in the right direction I would really appreciate it!

  If your object has already a colorTransform assigned, you can use its color property to access the colors of the object.  otherwise, you must use the bitmapdata class (first of all the draw method to create a bitmapdata example using your object then getPixel and getPixel32).

• Flash CS5 beginner - need help with Add URL link animated banner

  I apologize if this is a very basic question, but I am a newbie in Flash design. I created a basic animation in Flash CS5 and I need to add a clickable URL link. I tried a few tutorials that seemed promising, but none of them solved my problem. I tried a number of things, including the conversion to parts or all of the simple images buttons or movies and linking them this way as well as type in the code ActionScript 2 and 3, which none was successful. The animation plays correctly in my browser, but when I click it, the link does not work. I wish that the entire banner clickable to take viewers to the website linked instead to use the text of the hyperlink. Also, when I open the Code snippets window, it is empty, any image or image I selected. Do I need to import snippets of code somewhere or just will I things the wrong way? Any help is greatly appreciated!

  go to your help section and search the reference Guide of Action Script 3.  It is the repository of all the possibilities of ActionScript with Flash and Flex.  You can consult the alphabetical index URLRequest and navigateToUrl.  There could even be code samples included.  I haven't looked right, but you'll probably get before doing so.

  Best,

  -markerline

• Beginner needs help please

  I have some trouble setting a new file in my site to come.
  I did an external css file and I want to fix it to the new file.
  The banner, footer, navigation is the same for all pages.
  So if I understand correctly, I need to set the div in the new file.
  But I'm starting from scratch and there is nothing in the file.
  Please notify.
  
  I llove to just copy and paste these objects on the pages, that's why I created an external style.
  
  Thank you

  SSI = "server-side includes. Use F1 help DW and Google learn more about
  This.

  --
  Murray - ICQ 71997575
  Adobe Community Expert
  (If you * MUST * write me, don't don't LAUGH when you do!)
  ==================
  http://www.projectseven.com/go - DW FAQs, tutorials & resources
  http://www.dwfaq.com - DW FAQs, tutorials & resources
  ==================

  "jody25" wrote in message
  News:gignfp$4kq$1@forums. Macromedia.com...
  > I really appreciate the help.
  > I'm going to start a new topic with my next question, but even if I'm here
  > What SSI (PHP)?
  > I know that I've heard of PHP.
  > Certainly do not envy what I'm going through.
  > Thanks again
  >