Between the 2 separate companies sharing router

Similar Questions

• It is possible to switch between mode 'file separate globals' to 'share the same globals file mode' during the test run.

  Hi all

  It is possible to switch between mode 'file separate globals' to 'share the same globals file mode' during the test run.

  Or there is another option to use variables separated and shared at the same time for 2 parallel Sockets (ParallelModel.seq).

  Thank you

  Thank you

  I think it's useful!

• Unknown device on network adapter between the laptop and the wireless router

  I am running windows 7 64 bit on a laptop computer connected wireless to the router and internet.  The router is Linksys WRT160N connected to the internet.  The map of the network, there is a question mark device unknown between the laptop and the router.  However, I still have access to the internet.  In terms of network, if I hover over the laptop, it does not show an IP address.  It only shows the name of the computer and its MAC address.  Any help would be appreciated.

  Solved my problem.  I checked the button of the IPv6 protocol in the properties of a network connection on the laptop, and now I can see it's the IP address and the unknown device has been replaced by a switch and hub which is part of the router.   I do not uncheck the button IPV4.  I'm guessing that it is a bug in Windows 7 that you need to cut of ipV6 Protocol when you have a Win XP computer on the network if you want to see a map of own network.  As I said before, everything worked before, so this seems to be a cosmetic fix only.  I see that my shared files on the XP computer appear faster after a reboot.

• My speed has decreased between the router and the modem is not working properly, what can I do to increase the download speed with my Time Capsule 802.11n

  My speed has decreased between the router and the modem is not working properly, what can I do to increase the download speed with my Time Capsule 802.11n

  A variety of phenomena can affect the performance of its wireless network. You may be able to mitigate some negative effects.

  Solutions to any factors that may have an impact on your wireless network, read use the Diagnostics wireless for you help to solve the problems of Wi-Fi on your Mac - Apple Support.

• I followed the instructions to set up the home between my Mac and iPhone sharing 6, but I don't understand all the music on my iPhone

  I followed the instructions to set up the home between my Mac and iPhone sharing 6, but I don't understand all the music on my iPhone

  I have confirmed:

  (1) devices are on the same network

  (2) I am connected to my AppleID with the same account

  3) are my OS up to date (Mac 10.11.2) (9.2 iPhone)
  (3) I closed iTunes and the App has reopened

  (4) I turned my iPhone off and rebooted (and confirms the foregoing)

  On my iPhone, I see in my music library, different ' kind' listed (e.g., classic, recently added, music of the 1990s, etc.) but they are all empty.

  Im hoping to see the music I have in iTunes on my Mac and play these songs on my iPhone.

  IM thinking, music that would be shared from my computer to my phone will be on the cloud?

  (I did not all default to add my music in the cloud at the moment).

  Post edited by: abbeyinor

  Did you go into settings > music on your phone and sign in home sharing?

  See you soon,.

  GB

• Is it possible data passing between the screws running simultaneously in 2 separate teststand sequences?

  I have a vi that I want to run in a teststand sequence and then call another vi in a separate sequence, running in parallel. Is there a way of transmitting data dynamically between the two, the execution of vis?

  Just realised I can still use FVGs between the two sequences.

• Using variables shared between the different versions of labview

  Hello

  I look at the use of variables shared between two different versions of LabVIEW. We have a 2 of the PXI system and a single PC. We are currently updating the code on the PXI system to 2014, but the PC still work 8.2.1. We now need a map of ARINC-429, which is executed only 2009 +, that is why we are to day. First tests show that shared variables do not communicate between the two. I think that the reason may be that the PXI running the version of variable motor 2014 shared, while the PC is running 8.2.1, but I don't know if it is precisely for this reason it does not work. Is there a way to communicate between two different versions of LabVIEW with shared Variables?

  Thank you!

  SOLUTION

  There are two key elements in the process of installing software that are essential for PXI to communicate with another version of LabVIEW: Legacy Server Support Variable and Variable Support of Legacy Protocol. The first, in charge of the Protocol, was automatically installed through the selection of the other ingredients (although I do not know which triggered its installation). The second has been nested in the Protocol, but was not selected automatically.

  

  

  The Protocol allows the PXI 2014 connect to shared variables hosted by devices 8.6 or an earlier versions, while the server allows before 2009 devices to communicate to shared variables hosted on PXI of 2014 (which was the initial problem)!

• Routing problem between the VPN Client and the router's Ethernet device

  Hello

  I have a Cisco 1721 in a test environment.

  A net 172.16.0.0/19 simulates the Internet and a net 192.168.1.0/24 simulates the net, the VPN tunnel must go to (intranet).

  The net 172.16.0.0 depends on the router 0 FastEthernet, Intranet (VPN) hangs on Ethernet 0.

  The configuration was inspired form the sample Configuration

  "Configuring the Client VPN Cisco 3.x for Windows to IOS using Local extended authentication"

  and the output of the ConfigMaker configuration.

  Authentication and logon works. Client receives an IP address from the pool. But there's a routing problem

  side of routers. Ping client-side - do not work (the VPN client statistics that count encrypt them packets, but not to decrypt).

  Ping the router works too, but decrypt and encrypt customer statistics in VPN packets count progressive

  (customer has a correct route and return ICMP packets to the router).

  The question now is:

  How to route packets between the Tunnel and an Ethernet device (Ethernet 0)?

  conf of the router is attached - hope that's not too...

  Thanks & cordially

  Thomas Schmidt

  -.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.- snipp .-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.

  !

  version 12.2

  horodateurs service debug uptime

  Log service timestamps uptime

  encryption password service

  !

  !

  host name * moderator edit *.

  !

  enable secret 5 * moderator edit *.

  !

  !

  AAA new-model

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  !

  ! only for the test...

  !

  username cisco password 0 * moderator edit *.

  !

  IP subnet zero

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  crypto ISAKMP policy 3

  3des encryption

  preshared authentication

  Group 2

  !

  ISAKMP crypto client configuration group 3000client

  key cisco123

  pool ippool

  !

  ! We do not want to divide the tunnel

  ! ACL 108

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  interface Ethernet0

  no downtime

  Description connected to VPN

  IP 192.168.1.1 255.255.255.0

  full-duplex

  IP access-group 101 in

  IP access-group 101 out

  KeepAlive 10

  No cdp enable

  !

  interface Ethernet1

  no downtime

  address 192.168.3.1 IP 255.255.255.0

  IP access-group 101 in

  IP access-group 101 out

  full-duplex

  KeepAlive 10

  No cdp enable

  !

  interface FastEthernet0

  no downtime

  Description connected to the Internet

  IP 172.16.12.20 255.255.224.0

  automatic speed

  KeepAlive 10

  No cdp enable

  !

  ! This access group is also only for test cases!

  !

  no access list 101

  access list 101 ip allow a whole

  !

  local pool IP 192.168.10.1 ippool 192.168.10.10

  IP classless

  IP route 0.0.0.0 0.0.0.0 172.16.12.20

  enable IP pim Bennett

  !

  Line con 0

  exec-timeout 0 0

  password 7 * edit from moderator *.

  line to 0

  line vty 0 4

  !

  end

  ^-^-^-^-^-^-^-^-^-^-^-^-^- snapp ^-^-^-^-^-^-^-^-^-^-^-^-^-^-

  Thomas,

  Can't wait to show something that might be there, but I don't see here. You do not have the card encryption applied to one of the interfaces, perhaps it was not copied. Assuming your description you do it, or should it be, applied to the fa0 and you are connected. Try how you ping? Since the router or a device located on E0? If you ping the router, you will need to do an extended ping of E0 to the ip address of the client has been assigned. If your just ping the router without the extension, you will get sales and decrypts that you declare on the client. Have you tried to ping from the client to interface E0? Your default route on the router is pointing to fa0? You have a next hop to affect? You have several NIC on the client pc? Turn off your other network cards to check that you don't have a problem with routing on the client if you have more than one.

  Kurtis Durrett

• VPN tunnel between the concentrator 3005 and router Cisco 827

  I am trying to establish a VPN tunnel between the Central Office with VPN 3005 and controller branch Cisco 827 router.

  There is a router of perimeter with access set up in front of the 3005 list.

  I quote the ACLs on the Central perimeter router instructionsuivante to allow traffic to permit ip 3005 - acl 101 all 193.188.X.X (address of the hub)

  I get the following message appears when I try to ping a local host in the Central site.

  Can Anyoune give me the correct steps to 827 and 3005.

  Thank you

  CCNP Ansar.

  ------------------------------------------------------------------------------------------------------

  Debug crypto ISAKMP

  encryption of debugging engine

  Debug crypto his

  debug output

  ------------------

  1d20h: IPSEC (sa_request):,.

  (Eng. msg key.) Local OUTGOING = 172.22.113.41, distance = 193.188.108.165.

  local_proxy = 202.71.244.160/255.255.255.240/0/0 (type = 4),

  remote_proxy = 128.128.1.78/255.255.255.255/0/0 (type = 1),

  Protocol = ESP, transform = esp - esp-md5-hmac.

  lifedur = 3600 s and KB 4608000,

  SPI = 0x83B8AC1B (2209917979), id_conn = 0, keysize = 0, flags = 0x400D

  1d20h: ISAKMP: ke received message (1/1)

  1d20h: ISAKMP: 500 local port, remote port 500

  1d20h: ISAKMP (0:1): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM

  Former State = new State IKE_READY = IKE_I_MM1

  1d20h: ISAKMP (0:1): early changes of Main Mode

  1d20h: ISAKMP (0:1): lot of 193.188.108.165 sending (I) MM_NO_STATE

  1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE...

  1d20h: ISAKMP (0:1): will increment the error counter on his: retransmit the phase 1

  1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE

  1d20h: ISAKMP (0:1): lot of 193.188.108.165 sending (I) MM_NO_STATE

  1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE...

  1d20h: ISAKMP (0:1): will increment the error counter on his: retransmit the phase 1

  1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE

  1d20h: ISAKMP (0:1): lot of 193.188.108.165 sending (I) MM_NO_STATE

  1d20h: IPSEC (key_engine): request timer shot: count = 1,.

  You must also allow the esp Protocol in your ACL.

  access-list 101 permit esp any host x.x.x.x (address of the hub)

  Hope this helps,

  -Nairi

• EIGRP running between the router and ASA by switch

  Hello

  Is that possible I can running an EIGRP between router and ASA by switch?

  Router and ASA connected to the switch with static route.

  Hi Tommy Chin.

  It is possible, we must advertise to the route between the router and ASA.

  Please provide your connectivity diagram to better explain.

  For example...

  interface GigabitEthernet0/0

  Description links to WAN router

  nameif OUTSIDE

  security-level 50

  IP 10.1.1.1 255.255.255.192 ensures 10.1.1.2

  Summary-address eigrp 100 10.1.0.0 255.255.0.0 1

  !

  Confiuration Protocol EIGRP

  standard access list eigrpACL_FR allow a

  !

  Router eigrp 100

  eigrpACL_FR distribute-list in the interface outside

  neighbor 10.1.1.3 OUTSIDE interface

  neighbor 10.1.1.2 OUTSIDE interface

  Network 10.1.1.0 255.255.255.192

  redistribute connected

  redistribute static

  !

  Kind regards

  Srinivas.

  Note: if it solves your problem it mark it as resolved.

• Communication between the device IDS and router test

  I use a 4210 sensor, S47 Version 4.0 (2). I'm waiting on the upgrade memory provided under the contract until I can update above.

  Is there a way to test telnet between the detection device and the router? Stop ping at the firewall (we allow all ICMP traffic). I can't find a command 'telnet'.

  Thank you!

  John Kingston

  You must create a service account configuration mode (conf t) then:

  user service private service pass

  Sign out then as cisco, then reconnect you as a service. Telnet now works

• Sharing data between the host computer stores in different groups.

  I read in several places that sharing of data warehouses between the host in different groups is possible, but I don't get the warm and fuzzies when the hosts are different versions.

  vCenter is 4.1

  Group Alpha is 4.0 vmfs 3.33

  Bravo of cluster is 4.1 vmfs 3.46

  My goal is to move the virtual machines that meet the specific criteria of group Alpha for Cluster Bravo then the availability of flowing freely between clusters.

  The only concern I have is when adding Cluster Bravo to the same host of 3PAR alpha value of Cluster sharing all the data store, Cluster Bravo will try to reformat to vmfs 3.46 break Cluster Alpha to see the virtual machines stored in the warehouses of shared data?  I don't want to present the old warehouses of data to the new cluster only break from old cluster.

  Hello vmsjsn

  ESX/ESXi 4.X supports all versions of VMFS file system.

  Using your example of Alpha and Bravo. Kudos to will write more Alpha. you will be able to cross all hosts on the shared storage.

• Share resources between the 2 ESX 4.0 hosts without shared storage

  Hello guys,.

  I have the following question, I want to clarify.

  Imagine that we have 2 host ESX 4.0 with more functional license acquired (HA, VMotion, DRS, etc.)

  The two physical servers are identical. Don t have access to any kind of shared storage (San, no iSCSI, NAS no, etc.)

  In host #1 I installed all the virtual machines using local storage.

  Is it posible to use the host #2 resources (memory and CPU) to give more power to accommodate #1.

  My doubt is if it is posible to have a VM installed in local HD in home #1 and using RAM or / and CPU host # 2.

  Just do a cluster between the two hosts to empower the host #1 resources (not use DRS or functions of Vmotion)

  Let me know if I explained in a good way or not.

  Hope someone can clarify this for me.

  Thanks in advance

  It is not possible, even if you have the shared storage.

  There is no possibility that allows you access to CPU and memory of 2 resources different hosts.

  See you soon,.

  ~ Jean

  ~ Don't forget to points, if you found the useful answer

• How to disable the sharing of files between the host and guest XP PRO?

  Hello my setup is:

  Host of XP PRO and XP PRO comments using NAT.

  How to disable file sharing between the host and guest (do not want to view or access the file share on host comments)?

  In the comments

  I tried to disable simple file sharing in folder options and uninstall

  File sharing and printing of LAN properties but can always see and have access to the

  Organizing actions of folder...

  Help please!

  Then you will need to disable "Microsoft File and Printer sharing" or you need to set restrictions with the GPO. As long as the systems have their default values the value of a Microsoft network allows to use actions.

  If you found this information useful, please consider awarding points to 'Correct' or 'Useful' answers and answers. Thank you!!

• Any difference between the separate function and aggregation in sql query cost?

  Hello
  I've run many models sql stmts - such as:
  one) using a single table
  (b) using the two tables, using simple joins or outer joins
  
  but I didn't notice a difference in sql stmts in cost and implementation plan...
  In any case, my colleague insists on only using the aggregate function is less expensive compared to
  separate... (something I've not confirmed, that is why I believe that they are exactly the same...)
  
  For the situation described above under 1 sql... We could for example use
  

  select distinct deptno
  
   from emp

  select count(*), deptno
  
   from emp
  
   group by deptno

  select distinct owner, object_type from all_objects

  select count(*), owner, object_type from all_objects
  
  group by owner, object_type

  Have you ever found no difference between the two...?
  
  Note: I use Ora DB 10g v2.
  
  Thank you
  SIM

  Alexandre Gelin says:
  function separate and aggregation are for different uses and can give the same result, but if you use the aggregate function to get the separate records, it will be expensive...

  really? I find them almost identical to 11g. Actually GROUP BY is almost always more fast for me in the old days.

  article about this askTom Re: any difference between the separate function and aggregation in sql query cost?
  This applies mainly to the older oracle versions http://www.oracle.com/technology/products/rdb/pdf/distinct_derivedtables_groupby_sort_tech_article.pdf