Binds two ISP ASA to remote VPN Client to connect to instead of creating two profiles on the remote client

Hello

just a quick,

TOPOLOGY

ASA isps1 - 197.1.1.1 - outside

ASA ISP2 - 196.1.1.1 - backup

LAN IP - 192.168.202.100 - inside

I have configured Tunnel on the interfaces (external and backup), but is to link both legs public to serve a thare as redundancy for vpn users and users of the vpn tunnel leave pointing inside IP whenever they want to establish vpn sssion, we want it to be one, so if an interface fails vpn users will not know , but he will try the second for the connection. instead of creating the profile for the two outside of the leg on the vpn client.

is this possible?

Hi Rammany.

In your case, you have only an ASA that connects with 2 ISP in another segment IP... 196.x.x.x (Link1) & 197.x.x.x (Link2). What your condition is you want to have the VPN client who must be consulted with backup. If 196.x.x.x link fails, it should automatically take 197.x.x.x link. That too we should not have the config set in the VPN client backup server. You don have the possibility of having standby active also in asa single.

I think n so it will work with your current design.

This option is if your VPN client supports host name resolution (DNS). You can have the VPN created for both the public IP address share the same host name keeping the bond as the primary address 1 and 2 a secondary address. It will work alone.

Hope someother experts in our forum can help you with that.

Tags: Cisco Security

cisco_asa_prob.jpg

Here the IP Configuration and the routing of the Barracuda firewall table:

screen_shot_2014-08 - 12_at_16.01.42.png

I have a route on the Barracuda NG to the 10.10.10.0/24 network VPN Client on eth0.

The 192.168.1.0/24 LAN I ping the Client comes with Client VPN 10.10.10.11 as it should. But I can't ping or access network resources in the local network for AnyConnected customer's PC that connected through the VPN.

Here is the config Cisco ASA:

 : Saved : : Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz : ASA Version 9.2(2) ! hostname leela names ip local pool VPN-Pool 10.10.10.10-10.10.10.200 mask 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 switchport access vlan 5 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.250 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp ! interface Vlan5 nameif dmz security-level 50 ip address 172.16.0.250 255.255.255.0 ! ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server 192.168.1.10 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network obj_any subnet 0.0.0.0 0.0.0.0 object network VPN-Pool subnet 10.10.10.0 255.255.255.0 description VPN-Pool object network NETWORK_OBJ_10.10.10.0_24 subnet 10.10.10.0 255.255.255.0 access-list inside_access_in extended permit ip any any access-list inside_access_in extended permit ip object VPN-Pool any access-list dmz_access_in extended permit ip any any access-list global_access extended permit ip any any access-list outside_access_in extended permit ip any any pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 no arp permit-nonconnected nat (inside,dmz) source static any any destination static NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.10.0_24 no-proxy-arp route-lookup inactive access-group inside_access_in in interface inside access-group outside_access_in in interface outside access-group dmz_access_in in interface dmz access-group global_access global route dmz 0.0.0.0 0.0.0.0 172.16.0.254 1 route inside 0.0.0.0 0.0.0.0 192.168.1.254 tunneled timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy server-type microsoft user-identity default-domain LOCAL aaa authentication enable console LDAP_SRV_GRP LOCAL aaa authentication http console LDAP_SRV_GRP LOCAL aaa authentication ssh console LDAP_SRV_GRP LOCAL aaa authentication serial console LOCAL http server enable 444 http 192.168.1.0 255.255.255.0 inside snmp-server location Vienna crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map inside_map interface inside crypto map dmz_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map dmz_map interface dmz crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=leela proxy-ldc-issuer crl configure crypto ca trustpoint ASDM_TrustPoint1 enrollment terminal crl configure crypto ca trustpool policy crypto ca certificate chain ASDM_TrustPoint0 quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable dmz client-services port 443 crypto ikev2 remote-access trustpoint ASDM_TrustPoint0 telnet timeout 5 no ssh stricthostkeycheck ssh 192.168.1.0 255.255.255.0 inside ssh timeout 30 ssh key-exchange group dh-group1-sha1 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.254-192.168.1.254 inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept dynamic-filter updater-client enable dynamic-filter use-database ntp server 192.168.1.10 source inside ssl trust-point ASDM_TrustPoint0 dmz ssl trust-point ASDM_TrustPoint0 inside webvpn enable dmz no anyconnect-essentials anyconnect image disk0:/anyconnect-macosx-i386-3.1.05170-k9.pkg 1 anyconnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 2 anyconnect image disk0:/anyconnect-linux-3.1.05170-k9.pkg 3 anyconnect image disk0:/anyconnect-linux-64-3.1.05170-k9.pkg 4 anyconnect profiles AnyConnect_client_profile disk0:/AnyConnect_client_profile.xml anyconnect enable tunnel-group-list enable group-policy DfltGrpPolicy attributes default-domain value group-policy GroupPolicy_AnyConnect internal group-policy GroupPolicy_AnyConnect attributes wins-server none dns-server value 192.168.1.10 vpn-tunnel-protocol ikev2 ssl-client webvpn anyconnect profiles value AnyConnect_client_profile type user group-policy portal internal group-policy portal attributes vpn-tunnel-protocol ssl-clientless webvpn url-list none username tunnel-group AnyConnect type remote-access tunnel-group AnyConnect general-attributes address-pool VPN-Pool authentication-server-group LDAP_SRV_GRP default-group-policy GroupPolicy_AnyConnect tunnel-group AnyConnect webvpn-attributes group-alias AnyConnect enable tunnel-group Portal type remote-access tunnel-group Portal general-attributes authentication-server-group LDAP_SRV_GRP default-group-policy portal tunnel-group Portal webvpn-attributes group-alias portal enable! ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 ! prompt hostname context no call-home reporting anonymous hpm topN enable : end no asdm history enable

Can someone please help me solve this problem?

When I tried to solve this I didn't choose which interface the Packet Tracer?

The interface inside or DMZ interface? Inside, he says it will not work with the dmz but the error did not help me

Anyone here knows why it does not work?

screen_shot_2014-08 - 12_at_16.34.57.png

screen_shot_2014-08 - 12_at_16.33.06.png

Hello

Inside LAN is directly connected to the right firewall VPN... then I don't think you have to have the itinerary tunnele... can you try to remove the road tunnel mode and check.

entrance to the road that is static to achieve 10.10.10.11 as its display is correct...

Route by tunnel watch also with 255 administrative distance. I've never used that in my scenarios... lets see...

Concerning

Knockaert

VPN client - multiple connection possibilities?

Hi people,

My basic question is, Cisco VPN Client allows two simultaneous VPN connections at the same time?

I would like to implement the following:

Customer user (remote access VPN via Internet)--> Head Office c/o ASA 5520 pair--> (VPN remote access via Internet)--> pair of Branch Office ASA 5510 S + a/s

For example, to access the Branch Office system, the user must:

1. connect to the peer of Head Office ASA via Cisco VPN Client (the user/password authentication)

Head Office ASA peer gives an 172.16.1.x private IP address and is configured to route all requests for public office ASA IP through its own public IP address.

2. once Head Office VPN is established, the user establishes a SECOND VPN tunnel of the Cisco VPN client (user/password and focused on the cert auth)

I.e. branch sees the VPN connection try from the public IP address of Headquarters and therefore allows the VPN through the ACL traffic and allows the continuation of the VPN negotiations as usual. Customer is given another IP address private, 192.168.10.x.

Basically, I need to limit the remote access VPN branch to make it only accessible from Headquarters public IP address, no public IP address of the user (and therefore the entire internet).

I know this is an unusual configuration, and some will say on the sensitivity of security to allow two simultaneous VPN connections. These are the two networks of trust, strict ACL would be at stake and there is a long history behind this requirement...

Thanks in advance!

Alistair,

You can limit the access of VPN connections to branch by blocking connections on UDP ports 500, 4500 UDP and ESP and allowing him only from your home office. In this way, only the explicitly authorized public IP address of your home office would be able to connect to your remote sites by using an IPSec tunnel.

Now, on the second tunnel I don't think it's possible. As far I am aware you cannot have two connections to VPN at the same time of the same customer. The VPN will not let you do, it's mainly because when you have a VPN Client the VPN map session comes up and you can only one card virtual VPN.

Because I don't think it is possible I would advice to try something like this:

http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a008046f307.shtml

Could provide you the connectivity that you are looking for without needing a second tunnel VPN from the client side.

I hope this helps.

Raga

Function of automatic update for the IPsec VPN Client

Hello.

Do you have anyone ever tried the PIX / ASA ' feature IPsec VPN Client Auto-Update?

(see also Document ID: 105606).

He wants to make sure that I understand this right.

The user will receive a popup of information telling him to download the latest version of the client? And then there start the update itself?

If so, this would mean that the user must have the rights of full adminsitative using a laptop.

From my point of view, full administrator rights on a laptop are prohibited - 100% and therefore the functionality would be totally useless.

Anyone who can tell me whether I am good or bad?

Best

Frank

Frank,

You are right, if the computer desktop or labtop is completely locked regarding the installation of the software the customer won't be able to install it, they may be able to download from the link that you configured in ASA, once they connect to your server ASA RA but with regard to the installation user's machine needs rights profile appropriate to be able to install it.

HTH

-Jorge

Cisco VPN disconnection problem vpn client

Hello

We have a 8.2 (3) Cisco ASA and several vpn client ipsec that connect to it (5.0.07.0290 - k9 and 5.0.07.0410 - k9).

ExExactly after that 4 hours of these clients vpn connections are deleted even if the client is still sending traffic. I can't find any parameter configuration in order to avoid this connection drop. Someone has an idea how solve it?

I have

I have

AF

Hello

Please paste the output of "sh cry run." We can check the values of life.

also, you can activate him debugs following like half an hour before that the Client waits for the time to unplug.

Deb cry isa 127

Deb cry ips 127.

We can check the reason for the debugging by using the ip address of the client.

I hope this helps.

Kind regards

Anisha

P.S.:Please assign this thread answered if you feel that your query is resolved. Note the useful messages.

Unable to connect to other remote access (ASA) VPN clients

Hello

I have a cisco ASA 5510 appliance configured with remote VPN access

I can connect all hosts on the INSIDE and DMZ network, but not able to access other clients connected to the same VPN.

For example, if I have 2 clients connected to the VPN, customer and CustomerB, with a pool of vpn IP addresses such as 10.40.170.160 and 10.40.170.161 respectively, these two clients are not able to communicate with each other.

Any help is welcome.

Thanks in advance.

Hello

I'm a little rusty on the old format NAT, but would be what I would personally try to configure NAT0 on the 'outer' interface.

It seems to me that you currently have dynamic PAT configured for the VPN users you have this

NAT (outside) 1 10.40.170.0 255.255.255.0

If your traffic is probably corresponding to it.

The only thing I can think of at the moment would be to configure

Note of VPN-CLIENT-NAT0-access-list NAT0 for traffic between VPN Clients

list of access VPN-CLIENT-NAT0 permit ip 10.40.170.0 255.255.255.0 10.40.170.0 255.255.255.0

NAT (outside) 0-list of access VPN-CLIENT-NAT0

I don't know if it works. I did not really have to configure it on any ASAs running older software. There was some similar questions here on the forums for the new format.

-Jouni

Remote VPN client and Telnet to ASA

Hi guys

I have an ASA connected to the Cisco 2821 router firewall.

I have the router ADSL and lease line connected.

All my traffic for web ports etc. of ADSL ftp and smtp pop3, telnet etc is going to rental online.

My questions as follows:

I am unable to telnet to ASA outside Interface although its configuered.

Unable to connect my remote VPN Client, there is no package debug crypto isakmp, I know that I have a nat that is my before router device my asa, I owe not nat port 4500 and esp more there, but how his confusion.

I'm ataching configuration.

Concerning

It looks like a config issue. Possibly need debug output "debug crypto isa 127".

You may need remove the command «LOCAL authority-server-group»

NAT-traversal is enabled by default on the ASA 8.x version. So you don't have to worry about NAT device in the middle.

Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

Thank you

interface Ethernet0/0

Speed 100

full duplex

nameif outside

security-level 0

IP x.x.x.x 255.255.255.240

!

interface Ethernet0/1

Speed 100

full duplex

nameif inside

security-level 100

IP 10.88.10.254 255.255.255.0

!

interface Management0/0

Shutdown

nameif management

security-level 0

no ip address

!

permit same-security-traffic inter-interface

permit same-security-traffic intra-interface

network of the PAT_to_Outside_ClassA object

10.88.0.0 subnet 255.255.0.0

network of the PAT_to_Outside_ClassB object

subnet 172.16.0.0 255.240.0.0

network of the PAT_to_Outside_ClassC object

Subnet 192.168.0.0 255.255.240.0

network of the LocalNetwork object

10.88.0.0 subnet 255.255.0.0

network of the RemoteNetwork1 object

Subnet 192.168.0.0 255.255.0.0

network of the RemoteNetwork2 object

172.16.10.0 subnet 255.255.255.0

network of the RemoteNetwork3 object

10.86.0.0 subnet 255.255.0.0

network of the RemoteNetwork4 object

10.250.1.0 subnet 255.255.255.0

network of the NatExempt object

10.88.10.0 subnet 255.255.255.0

the Site_to_SiteVPN1 object-group network

object-network 192.168.4.0 255.255.254.0

object-network 172.16.10.0 255.255.255.0

object-network 10.0.0.0 255.0.0.0

outside_access_in deny ip extended access list a whole

inside_access_in of access allowed any ip an extended list

11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

NAT static NatExempt NatExempt of the source (indoor, outdoor)

NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

!

network of the PAT_to_Outside_ClassA object

NAT dynamic interface (indoor, outdoor)

network of the PAT_to_Outside_ClassB object

NAT dynamic interface (indoor, outdoor)

network of the PAT_to_Outside_ClassC object

NAT dynamic interface (indoor, outdoor)

Access-group outside_access_in in interface outside

inside_access_in access to the interface inside group

Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

dynamic-access-policy-registration DfltAccessPolicy

Sysopt connection timewait

Service resetoutside

Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

Crypto-map dynamic dynmap 10 set pfs

Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

Crypto-map dynamic dynmap 10 the value reverse-road

card crypto mymap 1 match address outside_1_cryptomap

card crypto mymap 1 set counterpart x.x.x.x

card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

card crypto mymap 86400 seconds, 1 lifetime of security association set

map mymap 1 set security-association life crypto kilobytes 4608000

map mymap 100-isakmp ipsec crypto dynamic dynmap

mymap outside crypto map interface

crypto isakmp identity address

Crypto isakmp nat-traversal 30

Crypto ikev1 allow outside

IKEv1 crypto ipsec-over-tcp port 10000

IKEv1 crypto policy 5

preshared authentication

3des encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 10

preshared authentication

3des encryption

sha hash

Group 1

life 86400

IKEv1 crypto policy 50

preshared authentication

the Encryption

md5 hash

Group 2

life 86400

IKEv1 crypto policy 60

preshared authentication

aes-256 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 70

preshared authentication

aes-256 encryption

sha hash

Group 1

life 86400

IKEv1 crypto policy 90

preshared authentication

aes encryption

sha hash

Group 2

life 86400

Telnet timeout 5

Console timeout 0

management-access inside

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

internal BACKDOORVPN group policy

BACKDOORVPN group policy attributes

value of VPN-filter 11

Ikev1 VPN-tunnel-Protocol

Split-tunnel-policy tunnelall

BH.UK value by default-field

type tunnel-group BACKDOORVPN remote access

attributes global-tunnel-group BACKDOORVPN

address pool Admin_Pool

Group Policy - by default-BACKDOORVPN

IPSec-attributes tunnel-group BACKDOORVPN

IKEv1 pre-shared-key *.

tunnel-group x.x.x.x type ipsec-l2l

tunnel-group ipsec-attributes x.x.x.x

IKEv1 pre-shared-key *.

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

Review the ip options

!

global service-policy global_policy

Excellent.

Evaluate the useful ticket.

Thank you

Rizwan James

Remote IPSec VPN - client Windows 7 and ASA 5505

Hello

I'm having trouble with configuring IPSec VPN with Cisco ASA 5505 and Windows 7 client native VPN remotely. My client PC Gets the VPN IP pool address and can access a remote network behind ASA, but then I lose my internet connection. I read that this should be a problem with the split tunneling, but I did as it says here and no luck.

Windows VPN Client settings, if I uncheck "use default gateway on remote network" I have an internet connection (given that the customer is using a local gateway), but then I can't ping remote network.

In the log, I see the warnings of this type:

TCP connection of disassembly 256 for outside:192.168.150.1/49562 to outside:213.199.181.90/80 duration 0: 00:00 0 stream bytes is a loopback (cisco)

I have attached my configuration file (without configuring split tunneling, I tried). If you need additional newspapers, I'll send them right away.

Thank you for your help.

Petar Koraca

That's what you would have needed on versions 8.3 and earlier versions:

permit same-security-traffic intra-interface

Global 1 interface (outside)

NAT (outside) 1 192.168.150.0 255.255.255.0

However I see that you are running 8.4 so I think that all you need is this (I never did on 8.4 so it may not be accurate)

permit same-security-traffic intra-interface

network of the NETWORK_OBJ_192.168.150.0_24 object

dynamic NAT interface (outdoors, outdoor)

Give it a shot and let me know how it goes.

ASA 5520: Remote VPN Clients cannot ping LAN, Internet

I've set up a few of them in my time, but I am confused with this one. Can I establish connect via VPN tunnel but I can't ping or go on the internet. I searched the forum for similar and found a little issues, but none of the fixes seem to match. I noticed a strange thing is when I run ipconfig/all of the vpn client, the IP address that has been leased over the Pool of the VPN is also the default gateway!

I have attached the config. Help, please.

Thank you!

Exemption of NAT ACL has not yet been applied.

NAT (inside) 0-list of access Inside_nat0_outbound

In addition, you have not split tunnel, not sure you were using internet ASA for the vpn client internet browsing.

You can also enable icmp inspection if you test in scathing:

Policy-map global_policy
class inspection_default

inspect the icmp

Hope that helps.

Two VPN clients remote need to Exchange resources through PIX501

I would like to have remote VPN clients ping each other and exchange their resiurces directly through pix501.

Is this possible? If so, how can I make it work?

With the current code of 6.x, u / shooting VPN traffic between sites or remote access clients is not possible, when this traffic ends on the same interface.

Pix 7.0 code is provided as a feature, which is scheduled for release in Q3.

Thank you

Peter

What VPN Client for ASA 5550 AnyConnect Premium connection?

We have version9 a couple of ASA550 I want to put in place a VPN client for use with remote access to administration. We have included AnyConnect VPN, Premium license peers 2 so I guess we can just use of Cisco AnyConnect VPN client. I went to Cisco's Web site and it says that I don't have right to the last Anyconnect VPN Client 4.x but I don't have access to the version 3.x.

The 3.x client is compatible with the ASA and also Windows 10?

If Yes, what is the correct file to use, there are many files listed for download in AnyConnect 3.x?

In addition, what is the difference between the AnyConnect 3.x and 4.x customer and why Cisco restricting 4.x?

Jim

AnyConnect 4.x has changed the licensing model. AnyConnect 4.x licenses are term based licensing vs perpetual 3.x. There are a number of other differences, mainly due to there being only two license types - more and Apex - no Mobile plus, Advanced Endpoint Assessment, shared VPN etc. Cisco offers a nominal or no license cost of migration until the end of 2015. (depending on what you have: positive Essentials or Apex at premium)

AnyConnect 3.1 will work with Windows 10 and the latest version of the Software ASA (since Version 3.1.10010). Reference:

http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/ANYC...

There are two ways it is distributed - as a stand-alone installation or package for the distribution of the ASA station. Both come in Windows, Mac OS X and Linux distributions. For a Windows client, you must use either:

AnyConnect-Win-3.1.12020-pre-deploy-K9.ISO

AnyConnect-victory - 3.1.12020 - k9.pkg

.. .to the current version of these respective form factors.

Binds two ISP ASA to remote VPN Client to connect to instead of creating two profiles on the remote client

Similar Questions

cisco_asa_prob.jpg

screen_shot_2014-08 - 12_at_16.01.42.png

screen_shot_2014-08 - 12_at_16.34.57.png

screen_shot_2014-08 - 12_at_16.33.06.png

Maybe you are looking for