BIOS Inspiron 2305 does not detect the drive in ahci mode

Similar Questions

• Qosmio F10: Driver Installation does not detect the wireless network card

  I wonder if anyone can help before I phone supported again. My motherboard is dead and ASP replaced and recovered my laptop qosmio F10. Since having back, my wireless card did not work.

  Windows detects a "network controller" whenever it starts and gives me the opportunity to install it. I tried to install it by navigating in the 'tools and utilities' records CD rom for folders and subfolders of "Wireless network driver" and it still does not detect the card.

  I also tried to install using the cd rom web gui and selected the 'Pilot wireless network' link and then tried to install it. It opens a dos command prompt and try to install but comes up with the error "failed installation.

  I ran the customer service and they told me to run the qosmio recovery/then recovery of product/recovery of qosmio and again...

  I still don't the card wireless not yet installed. This happened to someone else?

  I tried already shot the drivers from the web, but with no luck... If a representative of customer service with the help of good technical knowledge that would be great, or if someone has encountered the problem too and he had fixed to the give me some advice...

  Thank you very much

  Sean

  Hello

  you see the card wireless as an unknown device in Device Manager? If this is not the case, perhaps that the card was not properly installed after replacing the motherboard.

  Sorry I have no other idea.

  Good bye

• Re: Hitachi Drive Fitness Test (DFT) does not detect the HDD on Satellite A660

  I have a Toshiba Satellite A660 PSAW3C-047017 with a HARD MK6465GSX Toshiba drive. After experience, some consecutive failures of start-up, I was told on the Toshiba forums to use Drive Fitness Test (DFT of Hitachi).

  I burned the ISO to a CD and booted from it (I must press F12 for boot options and select the optical drive), which is to run successfully. However, it does not detect my drive HARD - the list is empty.

  Is there something I need to do to make visit to DFT?

  I cannot commend this third part software features, but I want to know if you still have these failures to start your portable computer satellite?

  What's the problem?

• w540 does not detect DVD drive

  W540 does not detect the CD / DVD drive and because it takes a long time to start.

  I know that I can put the hard drive to boot first, but now I want to install windows 7 and it does not start.
  I have already installed the latest version of the BIOS but does not solve everything.

  I wonder what's happening?

  Thank for the help that you can give me.

  I discovered why the player start out with reinstalling windows DVD.
  According to the manual, so that the operating system Windows 8 and Windows 8.1 work, Secure Boot function must be activated. Similarly, restarting the OS Optimized Defaults menu must be activated and when this setting is changed, some BIOS settings are changed automatically including the UEFI / Legacy Boot happening to UEFI. We need to change the UEFI / Legacy Boot for both, only then can start the DVD from the drive.

  I thank ColonelONeill for your help.

• Windows XP missing HAL. DLL file. CD ROM does not detect the Windows XP installation CD.

  I received the error message to the Windows startup, that I need to replace my Hal.DLL file.  I can't access a safe mode with command prompt, and CD rom does not detect the CD. I have rebuilt the Boot.INI file and still no luck. I tried to put HAL. DLL on a flash drive, but it cannot read it for some reason any. "Cannot develop"...

  Any help would be appreciated!

  Go to the store and buy an optical drive. They are very expensive. No, you cannot use the optical drive of your laptop. You can possibly create a bootable USB key with a distribution of Linux on it and copy the correct boot hard disk files. I say "may" because not all older computers can boot from a USB device. Look in your BIOS to see if your computer has this capability. If he can:

  http://www.pendrivelinux.com

  If you have not backed up your data, then you have trouble. While you're at the store also buy an external hard drive. You can start the computer with a Linux Live CD (in your new optical drive), and copy the files on the external hard drive. Then you can continue to try to repair your computer.

  MS - MVP - Elephant Boy computers - don't panic!

• Airport utility in windows 10 detect but wireless internet does not detect the hard disk, how to do?

  Airport utility in windows 10 does not detect the hard disk, how to?, the Office detect wireless internet no hard drive.

  What hard drive? It of a time capsule, or is it a drive connected to an airport extreme?

  What model number is the most convenient airport?

  Any plugged into USB drive must be formatted FAT32 (no other type of FAT as exFAT) or HFS +, IE standard Apple format.

  In addition, not all drives are recognized.

  The internal drive of the TC must be recognized, but there could be problems as well according to the age.

• IdeaPad Y500 does not detect the camera

  Hello everyone!

  I had my Y500 for about 1.5 years and I can't use the camera more. The computer does not detect the camera and when I downloaded and installed the camera software the computer shows me "no approperiate driver to install! I tried to uninstall the camera driver and reinstall it again, but it's the same problem.

  I would appreciate a quick response

  The problem was with the camera and the camera cable. I sent my computer to
  Lenovo and they fixed.

• X 220 does not detect the wwan card

  My X 220 does not detect the wwan card ("WWAN MSC PRTSWWAN RDY FUL" in the parts list). No section of modem in Device Manager, without any question related to the wwan card. Please someone help me, how to make my OS (Win 7 Pro x 64) can detect the wwan card?

  1.17 BIOS can detect, it worked normally.

• CD/DVD does not recognize the drive.

  CD/DVD does not recognize the drive.  Error message-"Insert a disk." "" "Insert a disk in the drive (E or F, depending on whether one in use).  I bought a DVD/CD thought exteranl today that might work.  Same error message with the external dvd/cd.  Can hear the disc turning when it is inserted during a short period of time, maybe 20 seconds, then it stops.  Sometimes, the disc is ejected when the error message appears, sometimes not.  Same results even with blank CDs.

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• The Digital Persona does not detect the fingerprint reader in Windows 7

  I have upgraded from Vista to Windows 7 Pro (full installation). Now, DigitalPersona does not detect the fingerprint reader. I tried to uninstall and reinstall the driver and the program, does not. Any ideas?

  Hi Cankermechanic,

  I suggest that you try to update the drivers supplied by Device Manager and check.

  See the link for update drivers: update a hardware driver that is not working properly: http://windows.microsoft.com/en-us/windows7/Update-a-driver-for-hardware-that-isn ' t-work properly

  If the problem persists, I would recommend that you uninstall drivers and reinstall the drivers from the site Web of Digital Persona, if that is helpful.

  If the problem persists, I suggest that visit you the manufacturer for further assistance from the link below:
  http://www.askpersona.com/

  I also recommend that you contact the manufacturer of the computer for further assistance on this issue.

  Thank you, and in what concerns:
  Swathi B - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Does not detect the hdmi cable more (very specific scenario)

  Well then...

  Got a monitor 15-HD to hdmi cable and a mac laptop (13 in the retina).

  So when I got all that I put it all together and it worked. I left because there a little bit, everything is plugged in and did not return for some time, so my mac fell asleep at the time wherever I went. Disconnected everything to relax on the couch. I went back and all plugged together again except that now the mac does not detect the cable. Tried a bunch of things with it. Restart, unplug the unit, detection manually, etc...

  Since the monitor is used and recently purchased cable, I thought time to them to test first. Got a laptop PC and plugged into the cable. The monitor and cable worked.

  Tried to connect my mac to the TV with my ps4′s hdmi since I did that a lot before. Also works.

  The problem is literally the combination between the cable and the mac. Which is a problem since I got the reason was to serve as my mac.

  During my research, I saw that specifically leaving the connected hdmi where sleeps your laptop can spoil it supposed to be... I saw it one time so idk if it's true, but it happened to me... and no, it wasn't really a solution when I came across that. Tried Googling this specific problem, but did not meet anything since my problem seems so specific.

  Fast forward to the next day and tried again now that both had little respite between them. Plugged into the HDMI and my laptop starts fading and return to a black screen. The screen would go black usually and so the laptop screen and the monitor would appear once again. sauf_que this time that there not, he just kept it and the monitor has not changed (Yes) it's). Not wanting to let him do that too long I unplugged and tried a different port with an adapter, I have also, since I did 3 holes I could use this for might as well try them all again. But unfortunately, I don't have it trigger anything again. So I went through another round of troubleshooting to try to make it work, but here I am, trying to see if anyone else has had this problem and solved. I am back to wait another day I guess and just hope. If not idk what to do, except maybe to get another cable? I don't know if this would solve it well.

  Hello Kaida W,.

  Thank you for reaching out to the Apple of community support. I'll do everything I can to help you get your monitor works as expected. Our first step would be to restore your System Management Controller (SMC) that allows to manage systems of different material on your Mac. This article will guide you through reset:

  Reset the management system (SCM) controller on your Mac.

  Try it and tell us how it goes. The entire community is here to help.

  Best regards-

• I have a My Passport to the top by car and I get error messages on this to be ejected (although it was still connected). Now my computer does not recognize the drive. All solutions?

  I have a My Passport to the top by car and I get error messages on this to be ejected (although it was still connected). Now my computer does not recognize the drive. All solutions?

  Drive, interface in the crankcase of training controller, or the USB port or the cable may be faulty.

• HP Support Assistant on my laptop or desktop does not detect the other machine.

  HP Support Assistant on my desktop or my laptop does not detect the other machine.  They are both on the same network.  Both are HP machines. Both are running Windows 10.  Is normal.  I would like to kind of monitor my desktop with my laptop when I'm away from home.

  @bmedbury

  The behavior you describe is normal - the HP Support Assistant is a program "per computer", in other words, each program HPSA lies and keeps track of just a computer on which the program is installed.

  When you see a post that will help you,

  Who inspires you, gives a cool idea,

  Or you learn something new.

  Click the 'Thumbs Up' on this post.

  My answer-click accept as Solution to help others find answers.

• Qosmio G50 does not detect the connected Bluetooth devices

  The qosmio g 50 (windows vista ultimate) detects more devices via bluetooth
  Until two days ago, I pointed out quietly via bluetooth mouse. And then, do not know what is success does not detect any more.

  I did a test to see if it could depend on the PC or the mouse.

  I took the phone with bluetooth, I turned and qosmio, is not detect the phone.
  And the phone does not detect the qosmio via bluetooth.

  What checks can I make on the qosmio while ' I detect devices via bluetooth?

  Tank you

  Hello

  BT has been successfully activated on tis G50?
  Have you used the FN + F8 key secret to switch on the BlueTooth?

  Please check if the FN key works correctly, otherwise, go to the button start-> all programs-> Toshiba-> Flash Cards Support utility and restart the software.

• I just installed an SSD on my imac 24 inch 2007 but at the start of the computer does not see the drive. How to use the terminal to look for? Thank you

  I just installed an SSD on my imac 24 inch 2007 but at the start of the computer does not see the drive. How to use the terminal to look for? Thank you

  Can she be seen by disk utility (and which version of Mac OS X is)