Black/cyan hp8500 fades to nothing even after cleaning

Similar Questions

• Nine HP OfficeJet Pro 8600 - when you copy, the picture is poorly marked, even after cleaning.

  I just bought the HP product above.  When printing or scanning, there is no problem and the images are clear.

  However, when you perform a copy in black, the result is badly streaked.  I cleaned the glass, etc., and it remains striated images.

  This is a new printer and avoid any accumulation of residues of the previous use.

  Suggestions?

  Hey, I'm sorry that you have this problem follow this link dguthrie

  http://support.HP.com/us-en/document/c02881567

  Tell me if this help you thx for all

• Pavilion G6-2301AX: fan keeps on a full speed of race even after cleaning

  Hello

  I bought this laptop in August 2013. In October 2014 began troubleing me lots of noise and the high speed of the fan and then after reading the forums, I cleaned it by the HP service center, but it has no effect on the laptop, it remains the same sound even when the laptop is cool. Properties of an instance, a few days back I kept my laptop on the way 'sleep' to full power, and when I checked after 6-7 hours full battery has been drained and this happens with this laptop only. You could hear the noise of the fan from across the room and it's getting really annoying now, because because of this behavior of the fan battery backup of the laptop has dropped dramatically. I guess it's a problem with the fan driver or something. Please help quickly before any hardware is defective because of the fan.

  Laptop computer is in Extended Warenty *.

  -Thanks in advance

  It looks like a hardware failure or a problem with the BIOS Setup.
  Try to take it in somewhere of HP and have then to study the fan.
  It would be under warranty, correct?

• D5160 - out printed striped, even after cleaning and replacement of cartridges

  THE SYSTEM CONFIGURATION:

  1. I bought my HP Photosmart D5160 (12/20/06) more than 3 years ago.

  2. I use ink cartridges only HP (98 for black, 95 for tricolor).

  3. I print photos on photo paper professional glossy inkjet.

  BEFORE THE PROBLEM:

  1. until a few months ago, I've been printing photos without flaw with the parameters mentioned above.

  2. sometimes after HP new installation of ink cartridges, a printed photo will print with streaks.  To resolve this problem, I would be 'Clean the print cartridges' through the 'HP Photosmart D5100 Toolbox series' and the photos would then print flawlessly.

  PROBLEM:

  1. beginning about two months ago, I am unable to have my photos Print flawlessly.  Photos Print consistently with some scratches.  I use the same paper, as I always have.  I buy HP ink cartridges at the same address as I always have.

  2 using the HP Photosmart D5100 series 'Toolbox', I clean the ink cartridges and make an intermediate clean, then a first.  Problem remains.

  3. I then cleaned the cartridges manually by the doc following HP (http://support.hp.com/us-en/document/c01711664), but the problem remains.

  4. I then replaced black and the tricolor ink cartridges and the problem remains.

  QUESTION:

  It is time to buy a new printer or is there something else I can try?

  Thank you

  Angela

  ``````````````````````````````````````````
  old computer: HP Pavilion PU131AV / a1050y, Intel Pentium 4 CPU 3.20 GHz, 2 GB RAM, Windows XP MCE, SP3 32-bit, Nvidia GeForce 6600
  new computer: HPE-180 t, Windows 7 Pro (64 bit), Nvidia GeForce GT 220, Intel Core i7 - 930 quad-core CPU @ 2.80 GHz, 8 GB of RAM

  UPDATE:

  After that print 10 pages on photo paper, all with streaks, I turned off the printer.  The next day, I tried again and without streaks.  I am considered to be research in an extended warranty for this product.  FYI, for information on extended warranty services, please contact:

  HP Technical Support team Sales Dept at 866-234-1377

• Firefox.exe APPCRASH associated ntdll.dll, even after clean install

  Hello, I have problems with Firefox crashes immediately after clicking on its icon.

  Firefox version is 41.0.2.5765, Windows exception code c0000005 (000497e8) the defective module ntdll.dll, version 6.3.9600.18007.

  Safe mode, the profile manager crashes too. I tried to do a fresh install which did not help...
  After that, I deleted my profile files, deleted temporary files, reinstalled Firefox, restarted the PC - problem persists.

  Unfortunately no newspaper is registered by Firefox.exe after the accident (folder/APPDATA/Roaming/Mozilla is empty).
  PC works fine otherwise.

  Windows error message reads:

  APPCRASH
  Firefox.exe
  41.0.2.5765
  561ee543
  ntdll.dll
  6.3.9600.18007
  55c4bc8e
  c0000005
  000497e8
  6.3.9600.2.0.0.256.48
  1029
  960C
  960cdc3073e4fd67c6d545df9e9d24cc
  7B3B
  7b3b9c2d872f7c0e875a33d7ebb7c470

  Thanks for any help!

  If the problem has been fixed. For all those who might happen to fall on this post:

  Firefox crash is caused by a problem of compatibility between Anti-Exploit Malwarebytes and Kaspersky Anti-virus. This problem has been resolved already my Malwarebytes sometime there are, but a recent update of Kaspersky AV brought. Can be solved by installing the latest beta version of Malwarebytes (1.08).

  To identify this issue I used this guide:
  https://support.Microsoft.com/en-us/KB/929135

• All-in-one HP Photosmart C309a "Alignment failed" error message even after cleaning the print heads, etc.

  About 3 weeks ago before making the error msg above, a large black ink blob appeared on my printed piece of paper.  This product for several sheets later, but kept decreasing in amount.  I continued to print & finally all traces of ink have disappeared.  2 days ago I got a msg of error on "load plain white paper. ", but the paper tray was plain white paper in it.  I have removed the paper, straightened and her successor. As a result, the msg "Alignment failed" appeared.  I went through all the steps HP online information on the treatment of the "alignment failed", including the cleaning of the printheads (the right amount of ink was on it), check the vents of cartridge, etc.  My question is: if I have 4 out of colored inks and a new black ink installed, the alignment is being affected by the old cartridges?  A msg on this appeared on the Control Panel, giving the opportunity to proceed with the old cartridges or install new ones, but be careful that it "cannot allow completion of...» "If 'old' were replaced not.  I need to replace these color cartridges or is it probably another problem, which is print head damaged?

  Checked the evacuation & there is no problem, so I tried the informal solution to put the printhead in hot water.  A ran 1 cleaning via / configuration on the printer and finally aligned with success tools.  I waited a while to respond because I wanted to see if the printer should continue to work, and there!

  Thank you very much.  I'm happy that I can keep this printer!

• PSC950 entrelardée impression even after cleaning and alignment of the heads

  My impressions were strips of different colors, when I print in normal mode (or project).  My ink cartridges appear to be good and are 3/4 full.  I cleaned the heads and aligned with them, but the problem remains.  Are there any suggestions as to what I can do to remove the problem?

  Eskimo wrote:

  My impressions were strips of different colors, when I print in normal mode (or project).  My ink cartridges appear to be good and are 3/4 full.  I cleaned the heads and aligned with them, but the problem remains.  Are there any suggestions as to what I can do to remove the problem?

  This would usually be caused by a problem with the interconnection.  Try cleaning the 78 cartridge and printer contacts as shown here.

• Smartphones from blackBerry Storm 9530 screen is black, no response, even after the Os re - install

  Hello.

  It's just a few months because I bought a second hand BB storm 9530 on Ebay.

  the phone was perfect for 1st 2 months... recently, few days back when I took my phoone out of the Holster, the screen was black but the backlight is turned on... I've done a few handfuls of battery and it seems to be ok,

  then he started to get worse, even after that the battery does no display on the screen, it was the dark night (except for the backlight).

  I started to get desperate, I reinstalled the operating system 5.0.0.32 8, it seemed to be ok for a few minutes, then back to the drawing board. I reinstalled the same version of the OS for a couple of times, but the screen did not show what either. not even the OS loading screen (the first one). I tried downgrading etc... no use...

  the phone shows no signs of improvement.

  Since my phone has not left any warranty, I don't know what to do.

  Please advice me what do.i yet tried loads the operating system using the AppLoader.exe

  I'm out of options.

  I am a resident of kerala, India.

  all my work related emails are merged with my BB... so, any help would really be appreicated.

  Thank you very much!!

  Shiv

  I agree.. is not sound like a problem of software for me, but rather the LCD needs to be replaced.

• 1320c streaks on the left flank, even after replacing PHD

  I have a DELL 1320c color laser printer about 2-3 years. A month or two ago it started printing the colours black and cyan light on the left side of the page.  A trail of light about 2 inches of width. Magenta is also a little lighter in the same place, but not as bad as black or cyan, which are very obvious. Yellow seems unaffected.

  I read the online help of DELL for the printer and he said this issue was most likely due to a printhead device worn and that they should replace all 20,000 copies. Then I ordered in a new PhD and successor scrupulously the instructions.  But the question remains the same! Even with a brand new doctorate it prints black and light cyan for the left 2 inches from top to bottom on the page, exactly like the old doctor.  PhD cost me only less than the price of a new printer!

  I also tried to replace with new toner cartridges. Still no change.  The toner will not rub off, so I don't see what is a fuser issue.

  Anyone has any ideas on what could cause this problem?  The help documentation is not any other possible causes.

  This mode of failure is unfortunately too often to go without explanation. The solution is actually quite easy (but complex) if it's not an oxymoron. The Dell 1320c is the licensed version of the Xerox Phaser 6125/6130 printer (who also suffers from the same disease). It's really a shame, since the printers do a great job of printing color accurate. IMO, the Xerox is better than the Dell. This is determined by the machine firmware and drivers, as printers are mechanically identical.

  The cause of the problem is the nipples of spring for K of waste and feed toner. On some machines, toner cartridges and some developers of K, the coupling between the nipples on the K and K toner cartridge developer becomes poor. Most often, you replace the toner cartridge K, the risk that this situation occurs. When the K toner is locked in place, the insulating foam on the front is supposed to surround and seal, the nipples on the developer of K. This is the path of the power/exit for toner K to/from the developer. When the seal fails, excess toner K can begin slowly to the 'dust' the vertical wall that you see when the PhD is removed. The same is true for the other tonics, but because they are progressively lower, they have fewer adverse effects.

  Behind this wall is (LSU) laser scanning unit. So that the "dusting" toner K continues, it can easily drift past the lenses that you see when you remove the doctorate. Toner settles on the LSU reflective mirrors (usually 1 or 2 in particular due to their orientation). As this drift toner continues to accumulate on the mirror reflective (s), it begins finally to block the laser beam to achieve OPC PHD drums. The result is a printed page with vertical columns of faded print (as shown in the photos posted earlier). Faded columns can be any width, depending on how much the reflecting mirror is contaminated. Because of the way that the reflective mirrors are arranged from LSU, black and cyan images are most often affected. The inside surface of the lens can also be sprinkled toner compartment and is cleaned in the same way. Cleaning the inside surface of the lens is usually optional because toner dust on the mirror (s) is usually the main cause of the faded print.

  The repair requires a dozen cotton qtips. Qtips with a rod of paper are preferable for this task, you will not want to distort the Publix in terms of access to the mirror or the surface of the inner lens. Store the handy default color solid surface test pages. The lenses are the entire width of the page. Mirrors are about 3/4 of the width of the page. The pages of default may be brought against the lens to indicate precisely where the surfaces have been coated with toner. Just remember that the side LEFT of the printed page is on the RIGHT of the USJ.

  Use the NEW qtips, directly from the package. Do NOT contaminate the cotton Publix with body oil, dust or liquid. Do ONLY 1 soft passes with the Publix on the affected mirror or lens, remove the Publix carefully and turn the Publix or use a new Publix before making another pass. If you make more than 1 pass with a contaminated Publix, you WILL just get DIRTY the reflecting mirror or lens with the toner!

  This operation MUST be performed with the box of LSU in front of you, it CAN be done without removing the printer LSU. USJ is a box, about 9 "x 9"x 5". It has a guide down rod which he locates in the printer. Having some at USJ 1 "thick foam will help stabilize it as you clean the mirrors. With USJ deleted, you need to remove his hood before which surrounds 4 cups. This cover just snaps on or out of the LSU through 4 locking tabs (2 on top) and 2 down. With the front cover, you have access to all the reflective mirrors and lenses. Make sure you just don't not one any part USJ to impact because the mirrors are aligned precisely. Just use common sense and caution.

  To remove the LSU time-consuming disassembly. I'm not going to explain these details. If the corrective procedure did you not flee, you should be mechanically inclined enough to find a way to remove the USJ. The only thing that requires more disassembly is the replacement of the power supply voltage.

  You want a screwdriver blade and phillips and needles slender beak. You have about three dozen screws to follow.

  Here are the steps in General:

  1. remove the top, side and back skins. Remove the fuse and the doctorate. Wrap the doctorate with a blanket or a black garbage bag to protect the CSPs.

  2 remove the i/o Board container (and updates fallow) after disconnecting all the internal its wiring plugs.

  3. you will need to loosen or remove certain media that supports some of the internal cables.

  4. remove all connectors LVPS then remove the card LVPS and tray on the top/back support (and set aside). You will need to strip the power wires of merger between the LVPS and the power connector of the fuser. You will probably need to remove the fan to remove the LVPS.

  LVPS and tray removed, you can look down on the LSU.

  5. the USJ is held in the printer by 2 Spring clips at the top (1 on each side, 2 screws each). These clips based on a 1/2 "steel pins that pinpoint the USJ. Remove the screws and clips and use steel pins to carefully lift the LSU out of the printer. Careful attention to the cable on the side, which connects the USJ to the controller card.

  6. after cleaning, reinstall everything in the order reverses. There is no mechanical alignment of the necessary LSU.

  -------

  ---

  The lower part of the image above reflects the positions of the mirrors and lenses. The Center more mirror (C & K) is more inclined to dusting because of his position, but your impressions of color sample will not indicate which surfaces need cleaning.

• I cannot install extensions, they appear with "will be installed after you restart Firefox" even after that I restarted.

  Hello

  I cannot install extensions, they appear with "will be installed after you restart Firefox" even after that I restarted.

  The 'Intermediary' folder is present and rest after a restart, but the extensions do not get installed. They show in the extensions page with the message "will be installed after you restart Firefox" and remain like that, no matter how many times I restart.

  Any idea?

  Under Firefox 24.0 Windows 8.1

  Thank you very much
  BD

  P.S. Just tried to install the add-on "convenience store" before asking the question and I got an error saying that it cannot install because it cannot change the necessary file. (I did manually instead)

  I tried to delete the files extensions.* nothing works. However, I deleted the addons.sqlite file and restarted my computer (computer not only Firefox) and that seemed to do the trick. Problem solved.

  Thank you for your help, it is appreciated.

• Hi, I installed an Alfred Workflow (see code below) that will mark all my mails as read. After you run it for a minute, the mail has crashed and I had to forcequit. However, now, when you open the Mail it crashes instantly, even after restart and repair o

  Hello

  I installed an Alfred Workflow (see code below) that will mark all my mails as read. After you run it for a minute, the mail has crashed and I had to forcequit. However, now, when you open the Mail it crashes instantly, even after restart and repair the permissions. I also used the Ctrl + C and CTRL-Z commands in the Terminal to leave the alfred_script, but nothing helped. I'm running out of ideas here, so I hope you could help me either reinstall the mail.app. I could always just switch to a different mail application, but it's kind of a last resort.

  Code:

  Tell application "Mail".

  Define allAccounts on each account name

  Repeat with currAccount in allAccounts

  the unreadMboxes value (each mailbox to the account currAccount the unread number is not 0)

  Repeat with currMbox in unreadMboxes

  (read status of each message to currMbox including the playback State is set to false) true value

  end repeat

  end repeat

  tell the end

  Any input would be greatly appreciated. Can post the report of crash on demand.

  Not sure that Alfred's, but it's just an Applescript script and it would not cause Mail to be planted.

  However, when running through all the messages, it is possible Mail database has been corrupted and it crashes because of this.

  I'll probably get anything out of the accident report, but others might.

  My first instinct would be to rebuild the mailbox. Because you can't do that with him crashing, you can simply delete the databases and it will rebuild them.

  Navigate to this folder:

  ~/Library/Mail/v3/MailData/

  You can either manually through the files, or copy the full path and paste it into go the folder in the menu go to the Finder.

  Remove the envelope Index files. Open Mail and see if it works well.

  If your library does not appear in your folder, hold down the Option key and select library in the menu go to in the Finder.

• Pavilion G6 2302 ax battery cell no. 4 tension showing o mV even after charging is complete.

  Hi guys,.

  My Pavilion g6 2302ax cell no. 4 battery voltage showing o mV even after a full charge.

  I baught my laptop 2 months before and its hardware works very well so far, I've noticed this problem. I've attached a screenshot of the HP support assistant screen. Please take a look.

  

  If anyone has an idea about this help please.

  Hello dipuab,

  Your battery test shows 0 on the fourth cell.

  There is nothing wrong with the battery, the test is designed for only three of the battery cells, test one of the tests will display 0.

  Here is a link to another post that had the same problem. Message 7 of 7.

  Hope it will be useful.

• HP G62:. Hp G62, laptop won't turn on even after trying hard. Help

  My laptop won't turn. Home from work two days ago and I tried turning on but nothing works. I read through messages to hard test but failed. I don't hear any sounds on my laptop either. Can someone please help me understand what I need to do to get my laptop running. Thank you

  Thank you. . No light even after plug in the laptop. I've never seen a light on the power adapter even when he was working. Where is the light on the adapter? Please help I feel empty without my cell phone

• HP Envy 5530: HP Envy 5530 told to replace the color cartridge, even after replacing with a new one.

  HP Envy 5530 said to replace the color cartridge, even after replacing with a new one.  Printer is 1 year old and I replaced the cartridges several times over the past year.  I am enrolled in the program of HP ink.  I can run the printer mode single cartridge using a black ink only and it works with my pc XP, Ipad, Chrome pc and mobile phone.  My pc win 8.1 will not print anything other than a test page.  Printer on the pc file lists always attention required when you try to print from the pc win 8.1.  I believe that the problem may be related to surface of cartridge for printing inside the HP envy heads 5530.  This part is available for purchase, and if so, where?

  I found a work around.  On the pc win 8.1, it seems that the print request must see a reset of the HP envy 5530 to print mode single cartridge.  I just start the pc and then reset the printer by lifting the hatch for the print heads.  That's all.  Once this is done, the 'attention required' message goes to the loan and it is able to print.  It will open a window, which suggests you add the color cartridge, but it will disappear when printing.  Simply open the door once and you can print until you turn off the pc.

• My computer keeps giving me the blue screen of death... even after that I reinstalled the operating system

  I have an emachines W3644... it came originally with windows xp family, but I currently have windows xp pro installed. It worked great for 4 months, no problems or anything. I got it sitting speakers... speakers were not connected or hung. I don't know if this could hit anything or not? My computer has 1.37 GB of RAM and the graphics card is a NVIDIA GeForce 6100 nForce 405.

  Questions are... Well, he keeps just randomly bluescreening. There isn't really a reason as that why, I'm the only person using this desktop computer, and I really did something to do that. I have scanned with many different scanners, and they found simple things like false positives and tracking cookies, none of which is a big deal.

  I tried many things to fix this myself... but nothing has worked. I'm starting to wonder if it's something to do with the material?

  I tried many things... include system restore, using the last known settings who worked, and also something to do with the domain controllers, or whatever.

  No one has solved the problem. He continues to randomly bluescreen. Also, a few times I clicked on records and he told me that they were corrupt, and when I right click on them and click Properties, it says that this folder contains 0 bytes of data... when there is more than 1 GB of stuff in there. This is the folder where I put my icons of computer maintenance and other things in.

  Then I'll reboot it'll randomly blue screen while windows is loading, he'll also do to the logon screen and sometimes even after connection... sometimes I it will load everything very well and it'll be on the desktop and I will leave the room and return, and it will be on the blue screen.

  I'm not sure what to do at this point. I reinstalled windows... and he still bluescreens. I copied most of the error codes he gave me... If someone could tell me please what they mean, or be of any help that would be great. I tried a lot of things... even reinstall... and he still continues to bluescreen. I also unplugged then replugged... all that does not work either. I also tried in safe mode, even in safe mode it bluescreens, sometimes even during loading safe mode.

  Anyway... Let me just enumerate all the error messages I've written... Please look at and if you know what NONE of them speaks, please let me know. I just want to know what his question is... so I can hopefully do this fix, or at least get another or something.

  Here are the error codes I wrote last week.

  STOP: 0X0000008E (0XC0000005, 0 X 00000322, AA4D7C68, 0X00000000)

  It mentions something about my bios if I remember correctly...

  STOP: 0X0000008E (0 x 0000005, 0XC0000005, 0XBF8A58CB, 0XA84EE96C, 0x00000000) win32k.sys-address BF8A58CB base at BF800000, DateStamp 4a8564c7

  STOP: 0X0000008E (0 X 80000004, 0X8165CE81, 0XAF311B38, 0X00000000)

  STOP: 0X0000008E (0XC0000005, 0X805656DE, 0XB7AC9770, 0X00000000)

  BAD_POOL_Header STOP: 0 x 00000019 (0x00000020, 0XE210A998, 0XE210AA38, 0X0C14020D)

  DRIVER_IRQL_NOT_LESS_OR_EQUAL STOP: 0X000000D1 (0X0001000C, 0 x 0, 00000002 00000000, 0X8A2D2700) wmaud.sys - address 8A2D2700 base at 8A2D2000, DateStamp 48025c3e

  STOP 0X0000008E (0XC0000005, 0X80564BB5, 0XA90F0C80, 0X00000000)

  PAGE_FAULT_IN_NONPAGED_AREA STOP: 0 X 00000050 (0 X 80898298, 0X00000000, 0X00000001, 0X8054BBB4)

  The BIOS in this system is not fully compliant ACPI STOP: 0X000000A5 (0 x 00000011, 0 X 00000007, 0XF771F180, 0 X 03000000)

  PAGE_FAULT_IN_NONPAGED_AREA STOP: 0 X 00000050 (0XBC99E00C, 0X00000002, 0X00000001, 0XAC9A203C)

  STOP: 0X0000007E (0XC0000005, 0 X 00002300, 0XB85E29F4, 0XB85E26F0)

  STOP: 0X0000008E (0XC0000005, 0X805454F3, 0XB9359B5C, 0X00000000)

  It's all the ones I copied. I tried to reinstall and still get errors. Please, someone tell me what these codes mean as soon as POSSIBLE.

  Thank you.

  If the RAM is only four months and you have identified that it is at the origin of the problems (e.g. the BSOD happen when only a single module of RAM is in) and then even after four months it can always happen.  Things such as ESD (Electro Static Discharge) or plug the RAM while it is still on the motherboard can cause these problems to happen... but they may or may not happen immediately.  The RAM could be faulty from the beginning, but has only gotten worse.  But unfortunately there is nothing that can make it work, if it is faulty, then it has to go back for a refund/replacement - as boring (and believe me, I know) that it is.

  0X000000BE normally concerns pilots in regards to the 0 x 00000050 - this normally either bad RAM, video memory, and bad devices (although not very likely) or bad memory Cache L2 (did not have a lot of people), but it can also be bad device driver software.

  I wish that the BSOD errors are actually more accurate as to describe what is at the root of the problem but they are not, and most of the time, it is by a process of elimination that we can solve the problems. However, I would say that if your original RAM works in the machine and you get only BSOD when the new RAM is in, then the new RAM is the culprit.

  Here's a little info on the RAM and it does: http://www.technologybasics.co.uk/WhatIsRAMAndWhatDoesItDo.html

  I hope I covered everything, but other questions, do not hesitate to ask :)

  --> I hope this helps! Please mark it as correct answer or vote if it does :)<>

  http://www.pcuk.biz - my Web site | http://www.systems-and-solutions.co.uk - where I work

  
  Info from Microsoft about phishing . Information from Microsoft on the fake security software