BlackBerry Smartphones BB docking station

Similar Questions

• BlackBerry Smartphones Docking station for Pearl to connect to my desktop computer

  Does anyone know if there is a docking station available where I could insert my Pearl and have it automatically synchronize with my Microsoft outlook and office computers at the same time?

  Check out this one:

  http://www.blackberryden.com/BerryBuddy.html

• Smartphones blackBerry Torch Docking Station

  Someone made a such docking station to recharge the battery?

  GoTo

  http://www.ShopBlackBerry.com/

  I used a pod before synchronization and works well, allows with PC sync or Charger just to load

  http://store.ShopBlackBerry.com/product/BlackBerryTorch9800SyncPod/ASY-14396-013

• BlackBerry Smartphones BB Curve 9300 white screen

  Hello

  My BB used to plant recently and does not start until I have remove and replace the battery, yesterday I was on a call when it crashed I have replaced the battery, but he would not return to the top!

  I read the previous posts however I could not find a solution, I know that this is not a screen problem because when I blace battery I get "Blackberry" and the loading bar, it loads for 2 ~ 3 seconds then the white screen, seen a lot of posts to check the application loader but I don't have it on my PC.

  My PC cannot connect to the device, I removed the battery and plugged to upgrade, but my BB is on the latest version.

  Help, please...

  OK... Thank you... but...

  ali25783 wrote:

  regarding the links earlier, they did not

  The links themselves did not work? Or you were able to get the articles, but the information contained therein were not useful? I can't say enough...

  ali25783 wrote:

  I have not apploader on my PC if this is helpful to all.

  If you have installed, your PC, the desktop software and/or a bundle of BONES for your BB, then you apploader. Reference:

  • http://supportforums.BlackBerry.com/T5/desktop-software-for-PC/cleanly-quot-starting-over-quot-with-...

  But, to start your diagnostic efforts, I recommend that you try to start safe mode:

  • KB17877 How to start a smartphone BlackBerry in Mode safe

  It will take several attempts to get the combination of keys ESC (press/release/hold) OK, so be patient. When properly in Safe Mode, see what happens.

  If the behavior continues, then well... think what happened just before this behavior started? A new application? An update? A theme? Something else? Think carefully that the slightest change can be causal... and try to undo all that was.

  If there is no Safe Mode, I suggest that you test to see if your battery is causal. Please try this sequence... Note that, throughout the entire 4h15m process, your BB must be directly connected to a charger checked (not PC USB, not a docking station):

  1. With battery, connect your BB to the wall charger
  2. Leave it alone for 2 hours, no matter what the LED or the screen not
  3. Remove the battery
  4. Wait 15 minutes
  5. Insert the battery
  6. Wait another 2 hours, no matter what the LED or the screen not

  This has been known to "revive" some BBs.

  It is also possible that your battery or BB has encountered a problem... to test, this sequence is necessary:

  1. Get a known good and already fully charged battery... use it in your BB and see what happens
  2. Get access to a BB good and the same known... use your battery in there and see what happens

  The results of this will show if your BB or your battery that has the problem. Carefully note please that 'new' and 'know' are not necessarily the same things. Although rare, a 'new' battery could certainly be defective. On the contrary, the easiest (and cheapest, btw) method to perform this test is to find someone with an identical BB which has no problem... trade in batteries and see what happens.

  Otherwise, then you may need to consider more drastic measures - WIPE, OS Reload, BBSAK Wipe/Reload and the process of reloading OS 'skeleton '. To prepare, you should be sure that you have a full backup of your PC... Please see the Backup link in my sig auto on this post for instructions.

  You may also use these tips:

  • KB10144 How to force detect the BlackBerry smartphone using the Application Loader
  • KB27956 How to recover a BlackBerry smartphone from any State
  • http://CrackBerry.com/BlackBerry-101-lecture-12-how-reload-operating-system-nuked-BlackBerry

  Good luck and let us know!

• BlackBerry smartphones can not connect BlackBerry Pearl 9105 for PC

  Hello world

  I have the following problem:

  After using my BB Pearl 9105 for almost 3 years, I can not connect to PC more (I still menu with choice of 3 options on my smartphone when I connect, but when I click on that option "usb" or "charge", the menu appears again).

  In addition, the PC does not recognize my smartphone as a usb device. Updated BlackBerry Desktop Software and the purchase of the new Micro-USB cable did not help.

  I can still load.

  Could anyone suggest me how to solve this problem?

  Hello and welcome to the community!

  Here is a list of troubleshooting items... I hope that something will be useful:

  • http://supportforums.BlackBerry.com/T5/BlackBerry-Desktop-software/tips-for-getting-BlackBerry-deskt...
  • KB10144 How to force detect the BlackBerry smartphone using the Application Loader
  • KB28457 BlackBerry Desktop Software is unable to detect the BlackBerry Smartphone because of administrative permissions
  • KB28458 BlackBerry Desktop Software is unable to detect the BlackBerry smartphone when user account control is enabled
  • KB28459 BlackBerry Desktop Software is unable to detect the BlackBerry smartphone when a full version of Roxio® Media Manager is installed
  • KB28456 BlackBerry Desktop Software is unable to detect the smart phone BlackBerry when the USB selective suspend setting is enabled
  • KB28444 The BlackBerry smartphone is not detected by the BlackBerry Desktop Software, when connected by USB to a USB hub or a docking station
  • KB28443 BlackBerry Desktop Software cannot detect the BlackBerry smartphone when connected via USB
  • KB02640 Troubleshooting USB connections
  • KB15486 Top 10 smartphone BlackBerry and BlackBerry Desktop Manager troubleshooting tips
  • KB00125 BlackBerry Desktop Software cannot detect the BlackBerry smartphone
  • KB11439 BlackBerry Desktop Software does not detect the BlackBerry smartphone when it is connected
  • KB00019 PIN code not displayed in BlackBerry Desktop Redirector
  • KB10938 "Current USB charge is insufficient," appears on the BlackBerry smartphone
  • KB01451 How to enable Sync advanced logging if a wired synchronization fails
  • KB19717 The BlackBerry smartphone is not detected as a USB mass storage device when connected to a computer
  • KB16310 Media Transfer Protocol and the BlackBerry Storm smartphone
  • http://supportforums.BlackBerry.com/T5/BlackBerry-Desktop-Software/Desktop-Manager-quot-disconnected...

  In addition, make sure you use only the root USB ports... without hubs (sometimes the front-end ports are hubs... use a rear USB port). And don't forget to try to disable the USB power management in the configuration of your system (Device Manager).

  Check also on the incompatible software... it was reported that NTI Shadow Ninja & software can cause a conflict; Remove and reinstall the desktop software BB allows to install correctly.

  My apologies in advance if this is redundant - there is no way to be sure that if you have already seen and tried these. Also apologies if all are not currently available... RIM takes their monte and descends at will as they revise things.

  I hope that something it is useful!

  See you soon!

• BlackBerry Smartphones Dead Blackberry 9900

  Hello

  My blackberry Bold 9900 died. A few weeks ago, I received a message to update the software on my phone I did but I discovered that it installed a few funny applications that I did not understand. A week after, my phone completely has been cut and it continues to Flash the red light. I tried to hook up with the USB on my computer but my computer does not recognize it.

  Major issues

  1. it comes at all, and after a few seconds, the Red led turns off.

  2. my computer does not recognize it when I connect it using the USB cable.

  Please help, thanks in advance.

  Hello and welcome to the community!

  Please try this sequence... Note that, throughout the entire 4h15m process, your BB must be directly connected to a charger checked (not PC USB, not a docking station):

  1. With battery, connect your BB to the wall charger
  2. Leave it alone for 2 hours, no matter what the LED or the screen not
  3. Remove the battery
  4. Wait 15 minutes
  5. Insert the battery
  6. Wait another 2 hours, no matter what the LED or the screen not

  This has been known to "revive" some BBs.

  It is also possible that your battery or BB has encountered a problem... to test, this sequence is necessary:

  1. Get a known good and already fully charged battery... use it in your BB and see what happens
  2. Get access to a BB good and the same known... use your battery in there and see what happens

  The results of this will show if your BB or your battery that has the problem. Carefully note please that 'new' and 'know' are not necessarily the same things. Although rare, a 'new' battery could certainly be defective. On the contrary, the easiest (and cheapest, btw) method to perform this test is to find someone with an identical BB which has no problem... trade in batteries and see what happens.

  Good luck and let us know!

• Curve of blackBerry Smartphones used to synchronize with outlook

  I had my phone for about 2 months with no problems.  I tried to sync the BB through the USB port on my Outlook calendar.  It goes to a certain folder and no synchronization.  The program of the break, then he must stop State.

  I tried to reinstall the software, take the battery and try again.  Now, the Director of bureau says that there is no device connected, when the phone is in effect.  It is connected through the same USB cable and port, as always with success, I used.  The device shows that it is load and connected via USB, and I can use the card out of holder, which means to me that the computer recognizes the device, but the Desktop Manager is not.

  I also tried to delete all of the rim as shown in another post on the Board of Directors, and this solution didn't or didn't help.

  Help!  Thank you!

  I think I can understand the problem.

  I have indeed restart the computer, and I use only a USB cord, not a docking station.

  Here's what I think I've found somehow.  BlackBerry dislikes Outlook folders with weird things in the note section (i.e.. Attachments or html links).  There is a calendar folder that I noticed that I added when this happened.  He had an html link in the section notes.  After removing the link in this article, I did the following:

  (1) use the Blackberry software disk and completely uninstall the Desktop Manager

  (2) battery Blackberry tour and take 1 minute.

  (3) when the battery is out of Blackberry, reinstall Office Manager.

  (4) restart the computer.

  (5) replace the battery and turn on BlackBerry.

  (6) run Desktop Manager

  (7) select synchronization > Configuration tab > Reset Configuration - this tab closing button

  (8) reconnect the Blackberry with the USB cable.

  (9) sync Outlook calendar

  Seems to work!  If all goes well it will continue to work, but if not, I'll let you know.  Thanks for the questions!  Hope this helps someone else.

• BlackBerry smartphones can not synchronize with the USB cable plugged into charge pod

  Hello

  I read on the web site of shopblackberry.com, in the details of charge pod ( http://www.shopblackberry.com/_blackberryaccessories/cgi-bin/pd.cgi?frompage=category&page=product_d... ) that the pod can handset with charger travel or data cable for charge and/or sync with a BlackBerry smartphone. So, my question is related on a problem or a misunderstanding of me to this description.

  I want to know if we could recharge and synchronize the BlackBerry via USB cable or is only responsible for the BlackBerry when connected that way. My second question is, is it possible to synchronize the BlackBerry with the USB cable plugged into the pod or not?

  Because I got a request from one of my users about the fact that his BlackBerry 9000 can not synchronize when it is on his group.

  Thank you very much!

  Hello

  It's a loading dock. It is useful, because just drag you your "BOLD" in there and it will load (just like the 8300 Curve).
  If you want to synchronize, you can plug a usb on the side of the appliance cord. This can be done while the machine is in its dock, where the description.

  I have the same crib, but for the 8300. It's really worth buying. I'm happy with it every day.

• Sync cradle for blackBerry Smartphones

  I've got a blackberrry Curve with a docking station.  The phone will load with the cradle, but I was wondering if I could use the cradle to sync with outlook.  I don't want to have to plug the USB key into the blackberry itself.

  Only 2 synchronization options with the USB cable and Bluetooth (http://www.blackberry.com/btsc/KB04132)

• BlackBerry Smartphones Software fails during synchronization with Outlook

  When I am syncing via USB my Storm with Outlook 2007 docking station, it fails when it reaches the timetable of the process part.  I use sync 2 channels on all of the components (tasks, contacts, calendar, etc.) and be successful, except when I accept a nomination of someone else in my Outlook calendar.  If I create an appointment in Outlook or on my BB, it syncs very well.  The only work around is send 1 channel from my computer to the Pocket PC and after that it's over, I turn it on to 2-way.  Of course, I could accidentally lose some entries and is certainly not a good workaround solution.

  I'm operating Desktop Software version 4.7 and my OS is Vista 64-bit.

  Hi and welcome to the jfetzer forums!

  See this link: http://supportforums.blackberry.com/rim/board/message?board.id=8300&message.id=48042&query.id=197058...

  Read the tif.log file after completing the Task 4 then go to task 5 once that the calendar entry deleted.

  Post back and let us know how it goes.

• BlackBerry Smartphones quite confused newbie with (iMac) & Blackberry Curve 8530 ordered

  I thought I posted this before but can't ind station. Maybe I'm in the wrong bench?

  Need to synchronize information on BB Curve 8530 with my iMac, Mobile me up and use to sync iPod Touch - questions are:

  1 can I disable MM before you install Blackberry software for Mac (Snow Leopard)?  I need to be able to sync contacts/address book, iCal with the new phone and am afraid of conflicts so I don't "disable Mobile Me.

  2 have you also looked at Mark/Space software to sync Curve 8530 - it might be a better program to sync with iMac - someone uses this or do you use the Balckberry software?

  3. do I have on the right forum for these questions I changed my subscription and I am in the right but not sure, so pls be kind enough to redirect me...

  thx for your patience.

  Hello, petunia

  Before you install the BlackBerry Desktop Software I would recommend support to the top of your address book and iCal on your Mac. Do this please open your address book, and then select the file (in the top menu) > export > Address Book Archive, and then click Save and placed on the desktop. Let then open iCal and select file > export > iCal Archive and click Save to place them on the desktop as well.

  You are now ready to install the BlackBerry Desktop Manager on your Mac. You don't need to disable mobile me to do this. After installation, restart your Mac and open the app to BlackBerry Desktop manager (it will be located in your main applications on the Mac folder). Follow the on-screen instructions to connect your smart phone BlackBerry for Mac.

  After the device is recognized and connected, you will have to configure synchronization settings. To do it please click on the items you want to synchronize under information and then select two way to sync with the calendar to sync or Sync Contacts(In the middle of the page). Once this operation is complete, you can go ahead and click the sync button located on the top right to start the synchronization process. During synchronization it will alert you that it's your first synchronization and it is recommended to replace the data on the BlackBerry smartphone. Please select this option to overwrite the data so that all the information of iMac you will be synchronized on your BlackBerry Smartphone.

  Once it is complete, you can eject your BlackBerry Smartphone by pressing the key of eject located in the lower right of the program.

  Thank you and you defenatly in the right place!

• MacBook Air for Docking Station connection problem

  I am trying to connect a MacBook Air to another monitor via a Kensington docking station, but they do not communicate. The additional monitor is sent immediately to sleep. If I connect Air to the monitor directly everything works fine, but I want to simplify my life with the docking station. Anyone have any ideas?

  Well, I understood the question. It seems that the original DisplayLink software I was using was not correct. After connecting with Kensington, they gave me info on a new beta driver and it works fine.

• An adapter that enables the new ipod touch be played on an old docking station for what they do?  I'm not tech savvy... any help is appreciated!

  Is there an adapter that will allow you to listen to music using the new ipod touch on a docking station that have the card that fits the older ipods?  I'm not warned, any help would be greatly appreciated.

  See http://www.apple.com/shop/product/MD823AM/A/lightning-to-30-pin-adapter.

• Docking station and of the menu bar does not appear automatically

  Hello

  I have some problems with the bar menu and Dock not appearing not to when the cursor is hoisted at the top and the setting up of the docking station...

  It appears in the Security Mode.

  In addition, the windows in Mission Control shows either, when you place the cursor at the top.

  I tried to kill the Dock. Finder and Menu bar in the Terminal with the command 'killall '.

  speculate as to what is wrong?

  -Kasper

  You can stop the process force using the background activity monitor utility. Just find the process Dock (sort the list of processes by name), or use the search box at top right, select, and then click the button exit (the icon is an 'X' in an octagon) in the upper left corner of the window of the activity monitor. It will ask if you want to make a normal Quit or force him to leave.

• The docking station uses Henge drivers?

  Is the Henge dock just a cable Organizer? -Seems all that is material.

  Or I need specific SOFTWARE drivers so that my Henge Dock to exploit 100% as expected?

  I use the Version B Henge Dock for my MacBook Pro 17-inch - and it all works when it is plugged.

  I just want to know if I'm missing out on something?

  THX

  Henge Docks are just a docking station, no software required, and any other features. Make sure to work your hard MBP while closed but, I think that life has been shortened on my Macbook, because it has been used mainly in the dock and couldn't cool properly with the lid closed all the time. The logic board failure.