Block a call with voice translation-rule
I have the voice gateway Cisco connected to the PBX through E1 PRI. I want to disable all PBX users make direct calls to _some_ IP phones. I tried to do it with the voice translation rule. Part of my config is shown below. But this configuration does not work. Where a mistake?
voice translation-rule 2
rule 1 rejection / ^ 57 [12456789] [1345678].
rule 2 rejection /^57[12456789]./
rejection of rule 3 / ^ 57. [123456789].
voice translation-profile NoDirect
translate called 2
Dial-peer voice voip 200
call block-translation-profile entering NoDirect
disconnect-cause invalid number incoming call block
destination-model 5 [78]... T
Setup progress_ind allow 3
session target ipv4:10.1.2.246
DTMF-relay h245 alphanumeric
codec g711ulaw 80 bytes
No vad
Good to hear that it has been solved.
Thank you
Radhika.
Tags: Cisco Support
Similar Questions
-
The numbers E.164 + and IOS voice translation rules
Hello
I have a cluster to CUCM 9.x with a plan of + E.164 numbering for the receivers, route patterns etc.
I have a gateway ISDN (2911 SRI with IOS 15.3 (3) M1) which connects to the PSTN.
The ISDN provider cannot accept the destination for the format + E.164 numbers so I need to manipulate the figures called before sending them to the PSTN switch.
I can of course do this with CUCM party called models of translation, but I wonder if it is possible to do the translation on the bridge instead?
The rule I tried to use below (Country Code of the United Kingdom).
rule 1 / ^ + 44\(.*\) / / 0\1 /.
I want it to do is + 44 at the beginning of the number of bands and replace it with 0
for example + 441234444666 becomes 01234444666
The rule I've tried fails because the + symbol is identified as a wildcard rather than in the number string I want to match.
Is there a way to get around this?
Thank you
Hello James
This is a regular expression, have you tried setting point (.) first then + followed by your number
I'll try in the laboratory
BR,
NadeemPlease note all the useful post.
-
Number of blocking outgoing calls with blackBerry Smartphones
new user - with BlackBerry 8520... How can I block my number when you call? THX, ak
Press your green dial key to enter the call log.
Press the Menu key > Options > General settings.
Scroll down to "restrict my identity = Yes.
And save.
-
Anwser a call with voice commands?
There is a way to do it? because sometimes I have my wet hands or something like that, and is a problem for me to have to touch the screen to anwser a call.
Thank you!
Currently, the closest thing I can say is that Assist has an option to respond to an incoming call in the driving view. Not much use when you do dishes, but... unless you do them while driving on the highway in a Winnebago.
This is something that has been proposed or requested before, but as yet, not been fully implemented.
-
BlackBerry Smartphones Block unsolicited calls
How to block unwanted with my BB 9810 calls?
Hello. There should be many applications on the BlackBerry World to block unwanted calls, with many options.
-
I exported a must of the site in HTML format and get the following error - MuseJSAssert: error calling the function switch: SecurityError: cannot read property 'documentLes' of 'HTMLIFrameElement': blocked a frame with original 'null '.
Does Anyon know what to do - how to fix this?
Hello
could you please take a look at this and see if that helps
Java Script alert: MuseJSAssert: error calling the function switch: security error?
-
So, what happens with this error message in the Muse?
MuseJSAssert: Call slector function error: SecurityError: cannot read property 'documentLes' of 'HTMLIFrameElement': blocked a frame with Malv "null" access to an image of the cross-origin.
It is a mistake to real security generated by the browser when you view a page with the iFrame content locally.
Please refer to the answer of Zak in the following thread: https://forums.adobe.com/message/6496180#6496180
See you soon,.
Vikas
-
How can I block a phone call with "no caller ID?
How to block phone calls that don't have "no caller ID?
There is no setting on the phone for that. You will need to contact your carrier.
-
SIP Dialer with voice gateway using the FXO Ports
Hello
We have a laboratory UCCE consisting of an outgoing SIP dialer and a h323 2811 voice modem router with 2 FXO ports. The Dialer reserve an agent and sending the call to the bridge, but the call fails immediately with the bridge return a "404 not found" error to the Dialer. Call directly from a CUCM extension attempts to connect successfully through the FXO. Any thoughts?
IOS Ver - T4 15.1 (3)
UCCE worm - 8.5.4
The gateway configuration:
version 15.1
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
sequence numbers service
!
hostname LAB-RS-ING_VXML-GW
!
boot-start-marker
boot-end-marker
!
!
logging buffered 50000000
no logging monitor!
No aaa new-model
no location network-clock-participate 1
!
voice-card 0
!
voice-card 1
dspfarm
!
dot11 syslog
IP source-route
!
!
IP cef
!
!
!
IP host mediaserver 10.15.80.83
No ipv6 cef
Authenticated MultiLink bundle-name Panel
!
!
!
!
!
!
Circuits-port FXO group
hunting-sequential diagram
!
!
!
voip phone service
No IP trust to authenticate
h323 connections allow h323
allow connections h323 to SIP
allow connections sip h323
allow sip to sip connections
no service additional sip refer
service additional media - renegotiate
signs before any
H323
Modem passthrough codec g711ulaw nse
SIP
interface FastEthernet0/0 source control binding
bind media source interface FastEthernet0/0
header-passage
!
voice class codec 1
g711ulaw codec preference 1
preferably 5 codec g729r8
!
vocal h323 class 1
H225 timeout tcp establish 3
!
!
!
!
translation-article 99 of the voice
rule 1 / ^ 4 / /334/
!
!
voice translation-profile PROFILE_TO_CVP
translate called 99
!
!
Crypto pki token removal timeout default 0
!
!
!
!
Archives
The config log
hidekeys
!
!
!
!
!
!
!
interface Loopback0
255.255.255.255 IP address 172.20.1.1
!
interface FastEthernet0/0
IP 255.255.255.0
automatic duplex
automatic speed
!
interface FastEthernet0/1
IP 255.255.255.0
Shutdown
automatic duplex
automatic speed
!
!
Router eigrp 15
10.0.0.0 network
Auto-resume
!
IP forward-Protocol ND
!
no ip address of the http server
no ip http secure server
!
IP route 0.0.0.0 0.0.0.0 10.x.x.x
!
!
!
!
control plan
!
!
voice-port 0/0/0
Ports FXO 1 trunk group
surveillance cut dualtone Mid-communication
output attenuation - 3
no echo - cancel enable
No non-linear
No vad
broadcast-maximum: 250
broadcast / nominal 200
minimum of playout / high-delay
broadcast-delay mode fixed
call waiting times - disconnect 5
timeouts wait-version 5
connection ÉRA 4930
4930 description
!
voice-port 1/0/0
2 ports FXO trunk-group
surveillance cut dualtone Mid-communication
output attenuation - 3
no echo - cancel enable
No non-linear
No vad
broadcast-maximum: 250
broadcast / nominal 200
minimum of playout / high-delay
broadcast-delay mode fixed
call waiting times - disconnect 5
timeouts wait-version 5
connection ÉRA 4198
4198 description
!
voice-port 0/0/2
!
voice-port 0/0/3
!
!
!
profile MGCP default
!
!
voice POTS dial-peer 1
incoming called-number.
direct line to inside
!
Dial-peer voice 2 voip
session protocol sipv2
incoming called-number.
codec voice-class 1
no class voice sip reset timer expires 183
DTMF-relay h245 alphanumeric
No vad
!
Dial-peer voice voip 4198
destination-model 4198
session target ipv4:10.15.80.81
codec voice-class 1
h323 voice-class 1
voice-class sip rel1xx taken in charge "100rel.
no class voice sip reset timer expires 183
DTMF-relay h245 alphanumeric
No vad
!
voice pots Dial-peer 301
trunkgroup FXO Ports
Description * MIA local calls *.
destination-model 305 [2-9]...
alert progress_ind activate 8
progress_ind enable progress 8
direct line to inside
prefix 305
!
Dial-peer voice voip 4930
destination-model 4930
session target ipv4:10.15.80.81
codec voice-class 1
h323 voice-class 1
voice-class sip rel1xx taken in charge "100rel.
no class voice sip reset timer expires 183
DTMF-relay h245 alphanumeric
No vad
!
Dial-peer voice voip 7000
Description of Agents
destination-model 7...
session protocol sipv2
session target ipv4:10.15.80.81
codec voice-class 1
voice-class sip rel1xx taken in charge "100rel.
no class voice sip reset timer expires 183
!
Dial-peer voice voip 9999
Phone agent test description
destination-model 9999
session protocol sipv2
session target ipv4:10.15.80.81
codec voice-class 1
voice-class sip rel1xx taken in charge "100rel.
!
Dial-peer voice voip 1444
Phone agent test description
destination-model 1444
session protocol sipv2
session target ipv4:10.15.80.81
codec voice-class 1
voice-class sip rel1xx taken in charge "100rel.
!
voice pots Dial-peer 303
trunkgroup FXO Ports
Description * LD calls *.
destination-pattern 1 [2-9]...
alert progress_ind activate 8
progress_ind enable progress 8
direct line to inside
Forward-digit 11
1 prefix
!
voice pots Dial-peer 302
trunkgroup FXO Ports
Description * MIA local calls *.
destination-model 786 [2-9]...
alert progress_ind activate 8
progress_ind enable progress 8
direct line to inside
prefix 786
!
voice pots Dial-peer 9
destination-model 91 [2-9]...
alert progress_ind activate 8
progress_ind enable progress 8
direct line to inside
port 0/0/0
Forward-digit 11
!
!
Dial-peer voice 1400 voip
Description of Agents
destination-model 14...
session protocol sipv2
session target ipv4:10.15.80.81
codec voice-class 1
voice-class sip rel1xx taken in charge "100rel.
!
!
!
!
!
Line con 0
line to 0
line vty 0 4
opening of session
transport of entry all
!
No Scheduler allocate
endDo you have installation trunks in call to the dialer Manager?
-
can't make an external call with CuCM and H323 gateway
Hi experts, I have a problem with CuCM and h323 Gateway. I use a 2811 router to make a gateway H323, CuCM server and Switch layer 2 build a VoIP LAB, this my network:
and my router configuration:
Current configuration: 2335 bytes
!
version 12.4
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
router host name
!
boot-start-marker
boot-end-marker
!
forest-meter operation of syslog messages
!
No aaa new-model
!
!
!
dot11 syslog
IP source-route
!
!
IP cef
DHCP excluded-address 192.168.1.1 IP 192.168.1.10
!
IP VOICE dhcp pool
network 192.168.1.0 255.255.255.0
option 150 ip 192.168.1.2
default router 192.168.1.1
!
!
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
voip phone service
h323 connections allow h323
allow connections h323 to SIP
allow connections sip h323
allow sip to sip connections
service additional h450.12
Fax protocol cisco
!
!
!
vocal h323 class 1
H225 timeout tcp establish 3
!
!
!
translation of the voice-rule 1
rule 1 / ^ 9.
!
!
voice translation-profile PSTN
translate 1 called
!
!
voice-card 0
!
!
application
Service flash aa1: its - cisco.2.0.2.0.tcl
paramspace English language en
paramspace English index 1
Param aa-driver 0839959204
paramspace location English flash:
prefix English paramspace
!
!
!
Archives
The config log
hidekeys
!
!
interface FastEthernet0/0
IP 192.168.1.1 255.255.255.0
automatic duplex
automatic speed
H323-gateway voip interface
port of link voip H323-gateway 192.168.1.1
!
interface FastEthernet0/1
no ip address
Shutdown
automatic duplex
automatic speed
!
IP forward-Protocol ND
no ip address of the http server
no ip http secure server
!
!
!
control plan
!
!
!
voice-port 0/0/0
cover of the echo - cancel 32
connection ERA opx 3100
Description 08395959204
activation of the caller ID
!
voice-port 1/0/0
!
voice-port 0/0/2
!
voice-port 0/0/3
!
!
!
1010 Dial-peer voice pots
Service aa1
incoming called number 08395959204
direct line to inside
port 0/0/0
!
voice pots Dial-peer 2020
PSTN description
translation-profile outgoing PSTN
destination-model 9 t
Setup progress_ind allow 3
progress_ind enable progress 8
port 0/0/0
Forward-digits all the
!
Dial-peer voice 10 voip
destination-model 1...
Setup progress_ind allow 3
progress_ind enable progress 8
h323 voice-class 1
session target ipv4:192.168.1.2
DTMF-relay h245 alphanumeric
Codec g711ulaw
No vad
!
!
!
!
Line con 0
line to 0
line vty 0 4
Cisco password
opening of session
!
Scheduler allocate 20000 1000
end
I have configured the gateway h323 and attach files to router parttern on follow CUCM
What is the problem and how to solve?
Thanks for all the help.
Your DP pointing CUCM is wrong, or your ÉRA OPX, depending on what you need.
voice-port 0/0/0
cover of the echo - cancel 32
connection ERA opx 3100
Description 08395959204
activation of the caller ID
Dial-peer voice 10 voip
destination-model 1...
Setup progress_ind allow 3
progress_ind enable progress 8
h323 voice-class 1
session target ipv4:192.168.1.2
DTMF-relay h245 alphanumeric
Codec g711ulaw
No vad
Your DP is waiting for 1... and you send 3100, they must match.
You might need to change the significantt numbers and entering CSS, but only you can know
For outgoing, you are throwing 9 predot, but again, expect it in your RFP, again, change as you need.
voice pots Dial-peer 2020
PSTN description
translation-profile outgoing PSTN
destination-model 9 t
Setup progress_ind allow 3
progress_ind enable progress 8
port 0/0/0
Forward-digits all the
You cannot transfer the numbers all send you also 9 for each call
Change your configuration you want / need.
HTH
Java
If it helps, please note
-
Unknown caller, leaving voice messages
Does anyone know how to prevent a caller to leave voice messages? Initially it was a normal number that I blocked. Now, it appears as Unknown caller and leaves voice messages all the time. I think it's one of these robo-dialers as voice messages, it leaves is just constant beep like a fax machine. I get about 5-7 calls from this number every day and it leaves a virtual machine all the time. Quite boring. I think that this beyond the normal settings on the iPhone so maybe there is an application that can do?
You can block someone from calling or texting you in two ways:
To block someone who has been added to the Contacts on your phone, go to settings > phone > blocked > add new. All Contacts window appears where you can scroll through the names and type the name of the contact you want to block. You will be taken back to the window blocked with the name added to the list of blocked contacts.
Parameters, contacts can be also blocked selection of Messages or Facetime and then following the instructions above.
In the case where you want to block a number that is not stored as a contact in your phone, go to the phone application > Recents. Watch the number (or name) you want to block and tap the blue 'i' with a circle around it to the right of the number. Scroll to the bottom of the plug contact that appears and select "Block this caller." The message "You will not receive FaceTime, messages or phone calls from people on the red list" appears with two options: block contact or cancel. Hit the block Contact to add the number to the blocked list, bad.
Block Messages by selecting the message with the contact and typing Contact thread in the upper right. Select the information icon and move forward with the same instructions as in the most recent in the phone tab.
-
update my windows Repir
My problem in my computer when I use the control panel but I reallydont know my computer problem im using my yahoo Messenger to call calll voice to my family, I can hear them, but the problem I can not hear themHi Kimberly,
Please provide more details - such as what exactly is the problem with Windows Update? Work any or you have problems with only a few updates (and if so, what are the numbers KB)? Can update you manually from the Microsoft Download issue KB site (assuming that you can get to the point where you can even see that)? Is the problem with all forms of update or automatic updates? When did start? Is the only problem that you encounter using the Panel of configuration-Windows Update?
As far as Yahoo Messenger goes, I recommend you seek assistance for their support to the: http://help.yahoo.com/kb/index?locale=en_US&page=product&y=PROD_MSNG&pir=7V.5laVibUnuoUu5c5XhZBBabICc7x5O4gEqzWIp0oGQmrFMhkLSxkV35MZ8jMUxDeQJkHWotyOSbrdkRCYfcW.Bvc7wn9THHnEG5w- dig deeper, I found a chat to help option in addition help topics.
I hope this helps.
Good luck!
-
How can smartphones blackBerry I block CERTAIN calls and sms
Hello, how do I block calls and sms in my Z10?, I do NOT want to block all calls but SPECIFIC NUMBERS, also retained the numbers (those with 'not available', 'out of area', 'private' description) coment: WP8 has already done this.
This feature will be supported in OS 10.3 but is not currently supported.
See you soon.
-
apex_util.prepare_url with the translated applications
I have two questions about the use of apex_util.prepare_url with the translated applications:
- Why is-checksum in a different translated application of checksum in the original application?
- Is there a way to control the apex_url.prepare_url checksum function calculates?
I have no application in both languages English (en) and Slovenian (sl). Link with English checksum would work if I put the Application primary language to English and the link with the Slovenian checksum would work if I set the main language Application to Slovenian. Application language is derived from the main language Application.
Sometimes, the real problem for me is I have 'English' version of checksum when apex_url.prepare_url is called from the "Slovene" to application version. As I mentioned before 'English checksum' does not work if the Application language is set to Slovenian.
I have reproduced this behavior (with the exception of the problem described in the previous paragraph) on http://apex.oracle.com/pls/apex/f?p=15120. An application illustrates an another unanswered question/bug related to translated app:
Is this Bug to Oracle APEX? Can anyone provide any advice or workaround?
Hello
bookmarkable (amounts of application or user level control) control totals depend on a salt value that is stored in the application. If the salt is null, there is a fallback to the alias of the application. If you update the salt by clicking "Expire bookmarks" on request > security attributes and re - publish the application, salt must be synchronized between the applications. Control totals should be the same, then.
Kind regards
Christian
-
headers block (block media recovery with rman)
Hi Im following this tutorial (sound on media with rman block recovery) - im using 11 GR 2 on oel 5.5
http://kamranagayev.WordPress.com/2010/03/18/RMAN-video-tutorial-series-performing-block-media-recovery-with-RMAN/
I created 2 spaces and storage within an array, for example I have a table space called "users02", composed of a data file called "users02.dbf", which currently holds a table called "tbl_test01".
If I query the table to select * from him, he returns the data inside, but when I use the following statement to determine the block header (for the purpose of the tutorial) no row is returned...
can someone help me on hwo I can find the header of the table,... is block - it possible that segment name is different in the name of the table?select header_block from dba_segments where segmemt_name='tbl_test01';
Any help would be appreciated806595 wrote:
Hi Im following this tutorial (sound on media with rman block recovery) - im using 11 GR 2 on oel 5.5I created 2 spaces and storage within an array, for example I have a table space called "users02", composed of a data file called "users02.dbf", which currently holds a table called "tbl_test01".
If I query the table to select * from him, he returns the data inside, but when I use the following statement to determine the block header (for the purpose of the tutorial) no row is returned...
select header_block from dba_segments where segmemt_name='tbl_test01';
can someone help me on hwo I can find the header of the table,... is block - it possible that segment name is different in the name of the table?
Any help would be appreciated
PLS, try:
select header_block from dba_segments where segment_name='TBL_TEST01';
Maybe you are looking for
-
15.a02 Aurora android update
I have aurora on my xperia arc s and it repeatedly tells me that there is an update, but it is the same version that tells me each time (15.0a2). I have download and install successfully, but am always notified of an update to the same version every
-
My music, podcast, playlists etc are gone
My iTunes console now looks like this. No music, no podcasts, not applications. I tried to reset iTunes twice, with the same results each time. The good news is that, as far as I know, my data is very good. I looked under user/music/iTunes, and music
-
Lenovo Y400 HDD partition after upgrade to 8.1 WIndows
I upgraded my Lenovo Y400 Windows 8.1, and I noticed that there are 8 partitions on disk 0. Is this normal? Otherwise, what partition I could merge/delete/resize without sacrificing the functionality of One (OKR) key recovery? I want to buy SSD in th
-
ink system failure officejet 6500
make system failure ink on officejet 6500, changed the cartridges, activated and deactivated
-
How to call this method?
I wrote this method earlier, but I do not remember how to call it. Can someone help me? public class PostReview extends Thread { String _url = new String(); public void Submit(String _url) { ConnectionFactory connFact = new ConnectionFactory(); Conne