Blue Screen error PAGE_FAULT_IN_NONPAGED_AREA & IRQL_NOT_LESS_OR_EQUAL after I found a redirect virus

The other day I noticed that I had a virus that was redirecting my searches on Google to scour.com. I used my anti-virus installed (PC-Cillin) and downloaded Malware Bytes removed the virus. Since then, my computer always gives me the blue screen of death once it starts. Startup of Windows and the programs that are supposed to start start to leave, but after a few minutes I STILL get the blue screen of death, and I'm getting various messages including IRQL_NOT_LESS_OR_EQUAL (no driver is listed), I also gottene PAGE_FAULT_IN_NONPAGED_AREA; It seems to be a different problem each time. What is going on? I still have a virus or something?
I tried the system restore, does not solve the problem. When I try to change the registry through the command prompt in safe mode to copy the \RegBack\ file beforehand, I get a "sharing violation". How can I fix the registry through safe mode?

Hello

To check again if the problem is caused by a Virus/Malware on the system, I suggest to refer to the link below and run the Windows Live OneCare safety scanner and check if the problem is caused by an Infection of Virus/Malware on the system

To run the scanner Windows Live OneCare refer to the link below

http://OneCare.live.com/site/en-us/default.htm

The Blue Screen of Death occurs when Windows encounters a critical problem which it can't get out without stop to stop operations after posting the diagnosis of the problem in the form of the Blue error screen.

Follow the steps below to solve the problem with the blue screen of death.

Method 1:

Try to access your computer in safe mode and follow the steps below. You can start safe mode and then try to repair the registry.

To start your system in safe mode follow the article below:

Start your computer in safe mode

Note:

Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

How to back up and restore the registry in Windows

http://support.Microsoft.com/kb/322756

 

Method2:

Step 1:

Try to perform the clean boot in safe mode and check if the problem persists:

To perform the clean boot follow the article below:

Clean boot

Note:
After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

Step 2:

Also try to perform the material clean boot when you start return to normal mode. To perform the starting material in minimum mode follow the steps below:

You can try to perform a clean boot material and check if the problem is caused due to all the equipment connected to the computer.

To perform the material clean boot, follow the steps below:

(a) disconnect all external devices.

(b) start the system in safe mode.

(c) go to Device Manager

Device that can be disabled to perform a clean boot material are

·         Video cards.

·         Sound card.

·         Network card.

·         USB devices and controller

·         CD\DVD.

·         Modems.

·         Ports (series and parallel)

After doing this, if you are able to Start in Normal Mode, try to activate the device one by one and find out which device is causing the problem. Try to install the latest driver for this device, or contact the vendor of hardware .

 

Method3:

You can run the control and verification of the disc if it solves the problem:

To perform monitoring of disk check the steps outlined in the article below:

http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors

For more information about how to manage the blue screen error please follow the article below:

How to manage blue screen errors in Windows 7

Tags: Windows

Similar Questions

  • Error on blue screen (BSOD) during and after the installation of Windows 7

    I had to reinstall Windows 7 using the recovery partition. When installing I kept getting blue screen errors and even now I still get the BSOD a few minutes. I have no problem in safe mode.

    My laptop is a Satellite C650D - 12 c. I tried to update the BIOS, but I can't do it in safe mode. What should I do next?

    Saved on the HARD drive recovery image is tested so everything should be OK with recovery image installation.
    What you can try is to use the Microsoft installation disc to see if the same thing will happen again.

    If Yes, I'm afraid, you need professional help with this Portable Mr. probably guaranteed so the service guy should check this.

    You created the recovery DVDs?
    BTW: I think that the update of the BIOS is not solution. Recovery facility must operate with this original version of BIOS.

  • After installing windows, there are a lot of blue screen errors

    Hello
    I just installed windows 7 ultimate. I've had computer problems for quite some time now. I tried a new operating system and I always get blue screen errors. These mistakes will be due to the lack of drivers (I have only installed 2 and everything that has been installed in the Service pack 1) or the malfunctioning of the equipment. Could you analyze these dump files and get back to me?

    Running on Windows 7 ultimate, 64-bit OS
    Toshiba with Intel processor

    Crash dump files are:

    http://rapidshare.com/files/1143482600/051213-32619-01.dmp%20-%20Shortcut.zip
    http://rapidshare.com/files/2723057529/051213-39437-01.dmp%20-%20Shortcut%20 (2) .zip
    http://rapidshare.com/files/1294305945/051213-39437-01.dmp%20-%20Shortcut.zip
    http://rapidshare.com/files/1739676114/051213-21918-01.dmp%20-%20Shortcut%20 (2) .zip

    Hello

    Thanks for posting your query in Microsoft Community!

    Resolve stop (blue screen) error in Windows 7

    http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

    Use SkyDrive download collected files and post screen shot/image

    http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65/

  • 8th Code blue screen error

    I get the blue screen of death (0000008e error code) each time I restart.  I ran an analysis of the system from the command line and it has not found something wrong.  What's next?

    Hello

    Don't forget on a new machine you change more they will claim that it is something that you did.

    0x00000008 may be one video (or other) driver, but it is often from memory or other hardware incompatibility
    questions. Since this is a new machine I invite you to participate in their support and not just less of
    their attachment completely. Don't just put in place with this intermittently as it will get worse.

    Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
    Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
    codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

    As examples:

    BCCode: 116
    BCP1: 87BC9510
    BCP2: 8C013D80
    BCP3: 00000000
    BCP4: 00000002

    or in this format:

    Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
    Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

    It is an excellent tool for displaying the blue screen error information

    BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and displays the
    information on all accidents of a table - free
    http://www.NirSoft.NET/utils/blue_screen_view.html

    BlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.

    You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
    system installed by the manufacturer.

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    You can try a system restore to a point before the problem started when one exists.

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

    -----------------------------------------------------

    Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).

    Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    ------------------------------------------------------------------

    Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
    smile, as well as of other major device drivers.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    ------------------------------------------------------------------
    How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
    http://support.Microsoft.com/kb/958233

    Troubleshooting, STOP error blue screen Vista
    http://www.chicagotech.NET/Vista/vistabluescreen.htm

    Understanding and decoding BSOD (blue screen of death) Messages
    http://www.Taranfx.com/blog/?p=692

    Windows - troubleshooting blue screen errors
    http://KB.wisc.edu/page.php?id=7033

    ------------------------------------------------------------------

    In some cases, it may be necessary.

    The Options or Vista recovery disk Startup Repair

    How to do a startup repair
    http://www.Vistax64.com/tutorials/91467-startup-repair.html

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    I hope this helps.

    Rob - bicycle - Mark Twain said it is good.

  • How can I stop the blue screen error caused by sffp_sd.sys

    Since the middle of the latest version of windows aprils has updated that I regularly get the blue screen... The last was 26/05/12 16:30...

    DRIVER_IRQL_NOT_LESS_OR_EQUAL

    STOP: 0X000000D1 (0X00000002, 0X00000000, 0X00000008, 0X914E8774)

    BTHUSB Device bthport.sys - 914E8774 address, base at 914E5000, Datestamp 4db03738

    Hello

    BTHUSB Device bthport.sys and sffp_sd.sys are the two components of Windows that means something else led him into
    Fault. First thing I would do is update the BlueTooth drivers. Check with the system manufacturer (mother's support-
    the Board Maker for systems (custom), their documentation online and drivers and ask in their forums (if any)
    known issues and/or / the real peripheral manufacturer support site. (See driver update methods in the next
    message.)

    ===============================================================================

    Pick up the pieces after a computer crash
    http://Windows.Microsoft.com/en-us/Windows-Vista/picking-up-the-pieces-after-a-computer-crash

    Check this thread for more information using BlueScreenView, MyEventViewer and other methods
    to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

    http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

    We can analyze the minidumps if make you it available to the SkyDrive or another file
    sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
    for the office or in the Documents folder and download them from there.

    ZIP or download the content of the C:\Windows\minidump

    Use SkyDrive download collected files and after shot/screenshot.
    http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

    ==================================================================

    BCCode: D1 0x000000D1

    Think video drivers especially if it may be others. Refer to the section of driver in my credits
    methods of troubleshooting blue screen below. BIOS, chipset of low level drivers and
    antispyway/antivirus/security programs can also cause this. Check the resolution of the problems and
    When you arrive at the driver and tests of memory sections do reference to generic methods in following
    message and then back to the if necessary troubleshooting tool.

    BCCode: D1 0x000000D1

    Cause

    A driver tried to access a pageable (or that is completely invalid) address while the IRQL was too high.

    This bug check is usually caused by drivers who used a wrong address.

    If the first parameter has the same value as the fourth parameter, and the third parameter indicates a runtime operation, this bug check was probably caused by a driver who was trying to run code when the code itself has been paginated outside. The possible causes for the error page are:

    • The function was marked as pageable and was operating at an IRQL higher (including obtaining a lock).
    • The function call was made to a function in another pilot, and that this driver has been unloaded.
    • The function was called by using a function pointer that was an invalid pointer.


    BCCode: d1 0x000000d1<-- read="" this="">
    * 1210.html? order = votes http://www.faultwire.com/solutions-fatal_error/Driver-IRQL-not-less-or-Equal-0x000000D1-

    =========================================

    Look in the Event Viewer to see if something is reported on those.
    http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

    MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
    TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
    http://www.NirSoft.NET/utils/my_event_viewer.html

    -------------------------------------------------------------------------
    Also this, so you can see the probable bluescreens.

    Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
    http://www.winvistatips.com/disable-automatic-restart-T84.html

    -------------------------------------------------------------------------

    Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
    info that would help. Such as ITC and 4 others entered at the bottom left. And all others
    error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

    As examples:

    BCCode: 116
    BCP1: 87BC9510
    BCP2: 8C013D80
    BCP3: 00000000
    BCP4: 00000002

    or in this format:

    Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
    Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

    It is an excellent tool for displaying the blue screen error information

    BlueScreenView scans all your minidump files created during 'blue screen of death '.
    hangs and displays information about all accidents of a table - free
    http://www.NirSoft.NET/utils/blue_screen_view.html

    BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
    There are other causes.

    You can do without if needed fail or the Vista DVD or recovery command prompt mode
    Options if your system was installed by the manufacturer.

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    You can try a system restore to a point before the problem started when one exists.

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

    -------------------------------------------------------------------------

    Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    The log can give you the answer if there is a corrupted driver. (Says not all possible
    driver problems).

    Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    -------------------------------------------------------------------------

    Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
    keyboard and mouse, as well as of other major device drivers.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    -------------------------------------------------------------------------

    How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
    quit unexpectedly
    http://support.Microsoft.com/kb/958233

    Troubleshooting, STOP error blue screen Vista
    http://www.chicagotech.NET/Vista/vistabluescreen.htm

    Understanding and decoding BSOD (blue screen of death) Messages
    http://www.Taranfx.com/blog/?p=692

    Windows - troubleshooting blue screen errors
    http://KB.wisc.edu/page.php?id=7033

    -------------------------------------------------------------------------

    In some cases, it may be necessary.

    The Options or Vista recovery disk Startup Repair

    How to do a startup repair
    http://www.Vistax64.com/tutorials/91467-startup-repair.html

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

  • Windows Vista, several blue screen errors

    Original title: BSOD

    Good afternoon

    I have the BSOD. Here they are in chronological order:

    1 IRQL_NOT_LESS_OR_EQUAL 0X0000000A (0X0000001D, 0XFFFFFFC2, 0X82424EF8, 0X00000001)
    2 0X000000c4 (0x000000A0, 0X96AEEA58, 0x995FCEE0, 0x0D99EEE4)
    3 0X000000c4 (0x000000A0, 0X968F0DF0, 0x99406EE0, 0x053F1D0A)
    4 0X000000c4 (0x000000A0, 0X9A651638, 0x993C4EE0, 0x10AB65F8)

    Additional information:

    Windows Vista Service Pack 2

    DualCore Intel Core 2 Duo E8400 3000 MHz (9 x 333)

    Gigabyte GA-G33M-DS2R (2 PCI, 1 PCI-E x 4, 1 PCI-E x 16, 4 DDR2 DIMM, Audio, Video, Gigabit LAN)

    DDR2-800 DDR2 SDRAM

    BIOS: Award BIOS v6.00PG Modular

    Could you help me... don't really know what to do...

    Hello

    Check this thread for more information using BlueScreenView, MyEventViewer and other methods
    to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

    http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

    We can analyze the minidumps if make you it available to the SkyDrive or another file
    sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
    for the office or in the Documents folder and download them from there.

    ZIP or download the content of the C:\Windows\minidump

    Use SkyDrive to upload collected files
    http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

    ----------------------------------------------------------

    BCCode: 0a 0x0000000A

    Drivers could be at fault, however the problems of disk or security/antivirus/antispyware products are
    just as likely to be the root cause that they can force a driver to corrupt or go out of bounds.
    The video driver or something affecting it would be questionable.

    At the end of this message, I'll post a bluescreen generic and in the next convenience store
    How do to update the drivers and BIOS but also to check memory message.

    -----------------------------------

    BCCode: 0a 0x0000000A

    Cause

    This bug check is issued if the memory paged (or invalid) is accessible when the IRQL is too high.

    The error that usually generates this bug check occurs after the installation of the faulty device driver or service system, BIOS.

    If you encounter a bug 0xA control during the upgrade to a later version of Windows, this error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version.

    Solve the problem

    If a kernel debugger is available, get a stack trace.

    To resolve an error caused by the faulty device driver or service system, BIOS

    1. Restart your computer.
    2. Press F8 to character-based menu that displays the choice of operating system.
    3. In the WindowsAdvanced Options menu, select last known good Configuration . This option is most effective when a pilot or a service is added at a time.

    To resolve an error caused by an incompatible device driver, system service, virus scanner, or backup tool

    1. Check the system log in Event Viewer for error messages that may identify the device or driver that caused the error.
    2. Try disabling the cache in memory of the BIOS.
    3. Run the diagnostics of equipment provided by the manufacturer of the system, in particular the scanner memory. For more information about these procedures, see the manual of your computer.
    4. Make sure that the latest Service Pack is installed.
    5. If your system has cards (SCSI) small computer system interface, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination.
    6. For devices (IDE) peripheral electronic integrated, set the built-in as only primary IDE port. Also, check each IDE device to the right setting master/slave/stand alone. Try to remove all IDE devices except for the hard drives.

    If the message appears during installation of Windows, make sure that the computer and installed devices are listed in the list of the products tested Microsoft Windows market.

    Comments

    Before upgrading to a new version of Windows, remove all third-party device drivers and system services and disable any antivirus. Contact software manufacturers for updates of these third-party tools.

    BCCode: 0a 0x0000000A<-- read="" this="">
    * 1025.html http://www.faultwire.com/solutions-fatal_error/IRQL-not-less-or-Equal-0x0000000A-

    ==================================================================

    Look in the Event Viewer to see if something is reported on those.
    http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

    MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
    TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
    http://www.NirSoft.NET/utils/my_event_viewer.html

    -------------------------------------------------------------------------
    Also this, so you can see the probable bluescreens.

    Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
    http://www.winvistatips.com/disable-automatic-restart-T84.html

    -------------------------------------------------------------------------

    Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
    info that would help. Such as ITC and 4 others entered at the bottom left. And all others
    error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

    As examples:

    BCCode: 116
    BCP1: 87BC9510
    BCP2: 8C013D80
    BCP3: 00000000
    BCP4: 00000002

    or in this format:

    Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
    Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

    It is an excellent tool for displaying the blue screen error information

    BlueScreenView scans all your minidump files created during 'blue screen of death '.
    hangs and displays information about all accidents of a table - free
    http://www.NirSoft.NET/utils/blue_screen_view.html

    BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
    There are other causes.

    You can do without if needed fail or the Vista DVD or recovery command prompt mode
    Options if your system was installed by the manufacturer.

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    You can try a system restore to a point before the problem started when one exists.

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

    -------------------------------------------------------------------------

    Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    The log can give you the answer if there is a corrupted driver. (Says not all possible
    driver problems).

    Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    -------------------------------------------------------------------------

    Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
    keyboard and mouse, as well as of other major device drivers.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    -------------------------------------------------------------------------

    How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
    quit unexpectedly
    http://support.Microsoft.com/kb/958233

    Troubleshooting, STOP error blue screen Vista
    http://www.chicagotech.NET/Vista/vistabluescreen.htm

    Understanding and decoding BSOD (blue screen of death) Messages
    http://www.Taranfx.com/blog/?p=692

    Windows - troubleshooting blue screen errors
    http://KB.wisc.edu/page.php?id=7033

    -------------------------------------------------------------------------

    In some cases, it may be necessary.

    The Options or Vista recovery disk Startup Repair

    How to do a startup repair
    http://www.Vistax64.com/tutorials/91467-startup-repair.html

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

  • Blue screen error / OS Version: 6.0.6002.2.2.0.768.3 / locale ID: 16393

    More information about the problem:

    BCCode: 1000008e

    BCP1:                                                   C0000005

    BCP2:                                                   82ACB455

    BCP3:                                                   BCC2C94C

    BCP4:                                                   00000000

    OS version: 6_0_6002

    Service Pack: 2_0

    Product:                                              768_1

    the last time it happened when I was running mozilla firefox in safe mode.

    Sound on a HP dv2000 laptop

    experts?

    Hello

    For troubleshooting see BlueScreens using BlueScreenView and MyEventViewer and other methods
    This thread - top 3 responses (+ 1 other).

    http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

    --------------------------------------------------------------------------------------------------------------

    Two main causes of this blue screen video drivers and BIOS - check with the system manufacturer
    Site for graphics (Video) card and BIOS, then on site of the manufacturer of the device for the last video. It may be
    other pilots to check there. Disable the installation of self as those who are older and if
    Updates Windows suggests a pilot just HIDE. Antivirus is another possibility.

    See methods of update driver generic in the next message.

    BCCode: 8th 0x0000008E is the same as 0x1000008E

    Cause

    Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.

    Common exception codes are:

    • 0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.

    Solve the problem

    If you do not have to debug this problem, you must use certain basic troubleshooting techniques:

    • Make sure you have enough disk space.
    • If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
    • Try changing video cards.
    • Check with your hardware vendor for updates to the BIOS.
    • Disable the BIOS memory options such as implementing caching or shading.

    If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.

    If you do not know the specific cause of the exception, consider the following:

    • Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
    • Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.

    If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.

    If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.

    Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.

    The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.

    You can solve the problems of BIOS by upgrading the version of the system BIOS

    BCCode: 8th 0x0000008E is the same as 0x1000008E<-- read="" this="">
    * 1151.html? order = date http://www.faultwire.com/solutions-fatal_error/kernel-mode-exception-not-HANDLED-0x0000008E-

    =============================================

    Look in the Event Viewer to see if something is reported on those.
    http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

    MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
    TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
    http://www.NirSoft.NET/utils/my_event_viewer.html

    -------------------------------------------------------------------------

    Also this, so you can see the probable bluescreens. (If necessary)

    Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
    http://www.winvistatips.com/disable-automatic-restart-T84.html

    -------------------------------------------------------------------------

    It comes to my convenience store generic bluescreen:

    Here are a few ways to possibly fix the blue screen issue. If you could give the info to blue screen
    This would help. Such as ITC and 4 others entered at the bottom left. And another error
    information such as the STOP codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

    As examples:

    BCCode: 116
    BCP1: 87BC9510
    BCP2: 8C013D80
    BCP3: 00000000
    BCP4: 00000002

    or in this format:

    Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
    Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

    It is an excellent tool for displaying the blue screen error information

    BlueScreenView scans all your minidump files created during 'blue screen of death '.
    hangs and displays information about all accidents of a table - free
    http://www.NirSoft.NET/utils/blue_screen_view.html

    BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
    There are other causes.

    You can do without if needed fail or the Vista DVD or recovery command prompt mode
    Options if your system was installed by the manufacturer.

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    You can try a system restore to a point before the problem started when one exists.

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

    -------------------------------------------------------------------------

    Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
    RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker
    (SFC.exe) program generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    The log can give you the answer if there is a corrupted driver. (Says not all possible
    driver problems).

    Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    -------------------------------------------------------------------------

    Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
    keyboard and mouse, as well as of other major device drivers.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    -------------------------------------------------------------------------

    How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
    quit unexpectedly
    http://support.Microsoft.com/kb/958233

    Troubleshooting, STOP error blue screen Vista
    http://www.chicagotech.NET/Vista/vistabluescreen.htm

    Understanding and decoding BSOD (blue screen of death) Messages
    http://www.Taranfx.com/blog/?p=692

    Windows - troubleshooting blue screen errors
    http://KB.wisc.edu/page.php?id=7033

    -------------------------------------------------------------------------

    In some cases, it may be necessary.

    The Options or Vista recovery disk Startup Repair

    How to do a startup repair
    http://www.Vistax64.com/tutorials/91467-startup-repair.html

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    I hope this helps.

    Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

  • Blue screen error STOP: 0x0000000A

    STOP: 0x0000000A irql not less or equal bvluescreen 1055 whats up?

    What's new?

    Hello

    See this thread for more information on using BlueScreenView, MyEventViewer and other methods of
    Troubleshoot the BlueScreens - top two responses.

    http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/8df6485a-50cc-4cdc-BE3E-0f05c7745117

    ==============================================

    References to Vista also apply to Windows 7.

    Drivers could be at fault, however the problems of disk or security/antivirus/antispyware products are
    just as likely to be the root cause that they can force a driver to corrupt or go out of bounds.
    The video driver or something affecting it would be questionable.

    At the end of this message, I'll post a bluescreen generic and in the next convenience store
    How do to update the drivers and BIOS but also to check memory message.

    -----------------------------------

    BCCode: 0a 0x0000000A

    Cause

    This bug check is issued if the memory paged (or invalid) is accessible when the IRQL is too high.

    The error that usually generates this bug check occurs after the installation of the faulty device driver or service system, BIOS.

    If you encounter a bug 0xA control during the upgrade to a later version of Windows, this error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version.

    Solve the problem

    If a kernel debugger is available, get a stack trace.

    To resolve an error caused by the faulty device driver or service system, BIOS

    1. Restart your computer.
    2. Press F8 to character-based menu that displays the choice of operating system.
    3. In the WindowsAdvanced Options menu, select last known good Configuration . This option is most effective when a pilot or a service is added at a time.

    To resolve an error caused by an incompatible device driver, system service, virus scanner, or backup tool

    1. Check the system log in Event Viewer for error messages that may identify the device or driver that caused the error.
    2. Try disabling the cache in memory of the BIOS.
    3. Run the diagnostics of equipment provided by the manufacturer of the system, in particular the scanner memory. For more information about these procedures, see the manual of your computer.
    4. Make sure that the latest Service Pack is installed.
    5. If your system has cards (SCSI) small computer system interface, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination.
    6. For devices (IDE) peripheral electronic integrated, set the built-in as only primary IDE port. Also, check each IDE device to the right setting master/slave/stand alone. Try to remove all IDE devices except for the hard drives.

    If the message appears during installation of Windows, make sure that the computer and installed devices are listed in the list of the products tested Microsoft Windows market.

    Comments

    Before upgrading to a new version of Windows, remove all third-party device drivers and system services and disable any antivirus. Contact software manufacturers for updates of these third-party tools.

    BCCode: 0a 0x0000000A<-- read="">
    * 1025.html http://www.faultwire.com/solutions-fatal_error/IRQL-not-less-or-Equal-0x0000000A-

    ==================================================================

    General troubleshooting BlueScreen to use with the methods above.

    Look in the Event Viewer to see if something is reported on those.
    http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

    MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
    TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
    http://www.NirSoft.NET/utils/my_event_viewer.html

    -------------------------------------------------------------------------

    Also this, so you can see the probable bluescreens.

    Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
    http://www.winvistatips.com/disable-automatic-restart-T84.html

    -------------------------------------------------------------------------

    Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
    info that would help. Such as ITC and 4 others entered at the bottom left. And all others
    error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

    As examples:

    BCCode: 116
    BCP1: 87BC9510
    BCP2: 8C013D80
    BCP3: 00000000
    BCP4: 00000002

    or in this format:

    Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
    Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

    It is an excellent tool for displaying the blue screen error information

    BlueScreenView scans all your minidump files created during 'blue screen of death '.
    hangs and displays information about all accidents of a table - free
    http://www.NirSoft.NET/utils/blue_screen_view.html

    BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
    There are other causes.

    You can do mode if necessary safe or the Vista DVD command prompt or
    Options recovery if your system is installed by the manufacturer.

    How to start on the System Recovery Options in Windows 7
    http://www.SevenForums.com/tutorials/668-system-recovery-options.html

    You can try a system restore to a point before the problem started when one exists.

    How to do a system restore in Windows 7
    http://www.SevenForums.com/tutorials/700-system-restore.html

    -------------------------------------------------------------------------

    Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to fix the system files of Windows 7 with the System File Checker
    http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates cbs.log Windows Vista (and Windows 7)
    http://support.Microsoft.com/kb/928228

    The log can give you the answer if there is a corrupted driver. (Says not all possible
    driver problems).

    Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

    How to run the check disk at startup in Windows 7
    http://www.SevenForums.com/tutorials/433-disk-check.html

    -------------------------------------------------------------------------

    Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
    keyboard and mouse, as well as of other major device drivers.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    Installation and update of drivers to 7 (update drivers manually using the methods above is preferred
    to make sure that the latest drivers from the manufacturer of system and device manufacturers are located)
    http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    -------------------------------------------------------------------------

    How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
    quit unexpectedly
    http://support.Microsoft.com/kb/958233

    Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
    http://www.chicagotech.NET/Vista/vistabluescreen.htm

    Understanding and decoding BSOD (blue screen of death) Messages
    http://www.Taranfx.com/blog/?p=692

    Windows - troubleshooting blue screen errors
    http://KB.wisc.edu/page.php?id=7033

    -------------------------------------------------------------------------

    In some cases, it may be necessary.

    Startup Options recovery or Windows 7 disk repair

    How to run a startup repair in Windows 7
    http://www.SevenForums.com/tutorials/681-startup-repair.html

    How to start on the System Recovery Options in Windows 7
    http://www.SevenForums.com/tutorials/668-system-recovery-options.html

    How to create a Windows 7 system repair disc
    http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

    I hope this helps.

    Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

  • [SOLVED] ATI HD series random blue screen error: error 0x0000007e ntoskrnl kb965494

    [Problems]
    Fixes random maps of BSOD blue screen of death ATI HD Series - spontaneous different random BSOD error codes every time
    Solves problems with his SoundBlaster X - FI (on board and add the map) extreme gamer - Sound sound seriously jerky or cut sharply off the coast
    Solves delays random system - system shuts down randomly for no apparent reason
    Solves the problems of disconnected Steam - quite noticeable in Call of Duty 4 Modern Warfare 2
    Resolved A of Call of Duty 4 Modern Warfare 2 in delays play random or falling of the game so that your game. Usually, when first start the game. Not having not NAT enable may cause a similar delay as well.
    [Source of problem]
    The problem is with an older driver a new loading equipment when you first load the operating system from Microsoft. Shame on you, Microsoft.  6 weeks to understand it and it is CLEARLY without Microsoft. Sorry, but none of the NDA here.
    Its a simple problem, yet almost impossible to find. Catalyst install Manager - ATI HDMI Audio Device will add an Audio device rather than to replace the device driver Audio HDMI Microsoft load the OS installation stage. Or the pilot is ignored all together because Microsoft has already loaded a driver installation for this device.
    [Clean Install FIX]
    When you install the ATI Catalyst 10.6, use the custom installation and exclude the HDMI Audio by unchecking the box next to the HDMI Audio. Pilots still end upward in the ATI Catalyst install directory if you can note the ATI installation path. The problem is that ATI will add an HDMI high definition audio device, DOES not replace the Windows device already loaded. Or may not charge a second device. Whatever it is, it uses the Microsoft device driver.
    Updated driver software with the driver - Microsoft high definition Audio Device driver ATI manually following the instructions below.
    [Windows OS already loaded FIX]
    -Device Manager-
    Manage driver updated using computer-> right click-> appliances-> sound-> right click HDMI high definition Audio Device-> update driver and browse to the directory of ATI (check include subfolders).
    Also noticed the BIOS default settings cause problems of NB and DRAM. Overclocked to mount pressure on the system. Even if I adjusted the settings of the BIOS, I have always many BSOD until I updated the driver for high definition Audio Device from Microsoft with the ATI driver.
    Ubuntu ran without a single question before changes to accommodate the Windows 7 operating system. For some reason any Windows is picky about certain parameters so that Ubuntu 10.04 LTS loads and runs without a single problem.
    I have the logs memory.dmp and mini.dmp. Any help and any help appreciated :D
    After running through the following steps, the problem here is the ntoskrnl.exe causing several bugs (BSODS). Even if it's a problem with Vista, this problem occurs with Windows 7.
    • Event ID: 1001 Source: error checking
      The computer was restarted after a bugcheck.  The bugcheck was: 0x0000007e (0xffffffffc0000005, 0xfffff88000e34294, 0xfffff880031bda18, 0xfffff880031bd280). A dump was saved in the: C:\Windows\MEMORY. DMP. Report ID: 052310-17316-01.

      The computer was restarted after a bugcheck.  The bugcheck was: 0 x 00000109 (0xb3b7465eeb217b7e, 0xfffff80002d18cc0, 0xa3a039d898a4a950, 0 x 0000000000000001). A dump was saved in the: C:\Windows\MEMORY. DMP. Report ID: 052110-23197-01.

    OS: Microsoft Windows 7 Ultimate 64 bit
    Antivirus: Microsoft Windows Security Essentials
    Motherboard: Gigabyte GA-890FXA-UD5
    RAM: 8 GB CORSAIR DDR3 4 GB 1333 MHz CORSAIR TW3X4G1333C9A TWIN

    Video: Diamond ATI Radeon HD5850 1 GB DDR5

    PROCESSOR: AMD X 4 965BE
    HD: Hitachi 1 TB HDE721010SLA330 S/N MS03G16K
    PS: Antec EarthWatt 750W PSU V2.3
    KB: Logitech G15
    Mouse: Razer Deathadder 3.5 G
    Gamepad: Belkin n52te
    First try to solve this problem:
    Fresh OS loaded and BSOD immediately after the restart. Reason or details is unknown because of the immediate reboot without a kernel image. No events logged in Windows event logs with error checking information.
    At ran Windows Update for the current patches. Random BSOD on restart.
    Load the ATI Catalyst 10.4 Suite for Windows 7 (64-bit). Random BSOD on restart.
    Problem again when the system is stopped and started. Chances are THAT BSOD will occur without emptying the core or the mini writing.
    Run the checker - 90% chance of BSOD
    Ran Check Disk - seems to be stuck on stage 4 'verification data file' 57531 63472 processed files. 01:05: PM 05/21/2010 FAIL stopped here 13:44

    Second attempt to solve this problem (low-level format):

    Using Hitachi tools - http://www.hitachigst.com/hdd/support/download.htm Drive Fitness Test - Switch BIOS from AHCI to IDE to access the SATA drive.
    Quick Test results - HDE721010SLA330 successfully completed / Disposition Code = 0x00
    Clear the result of the boot record - 0x00
    Wipe the drive (drive clean takes time for 1 to ~3.5 hours) / 17:07 Media Analysis / 20:20 hours of fact and change the outcome - success 0x00
    Updated the BIOS with F2 14/05/2010 (CPU compatibility improve)
    Press DELETE to enter BIOS F8 to enter the Q - Flash insert USB Thumb Drive (a drive if no floppy is in system) select the file
    Change the BIOS settings-
    Integrated Peripherals-
    OnChip SATA Type [Native IDE] change on [AHCI]
    (No Option for this) F6 for drivers to be loaded in Pre-os Windows 7 64 bit

    Install Windows 7 Ultimate 64 bit at 21:02 / Installer Reboot 21:14 / end of installation restart 21:18 / finalised result 21:21 - GOOD

    Install the driver USB 3.0 NEC 21:22 - result - GOOD
    Automatic update added KB978601 (pending reboot) and KB979309 - result - GOOD

    Install the network drivers Realtek Lan_win7 - result - GOOD

    Install win7_chipset (installed ATI Catalyst install manager 03.00.0765) 21:30 - result - BSOD KERNEL DUMP RENOWNED MEMORY. DPM at 5212010935PMMEMORY. DMP

    Hitachi configured disk requires reboot (stop for cold start) - 21:37 - result - connected

    Install Microsoft Windows Security Essentials 64 bits 21:43 d/l latest and scan / to 21:49 results - GOOD

    Shutdown - 21:51
    Power - result - GOOD
    Install ATI 10-4_vista64_win7_64_dd_ccc_wdm_enu (taken from the site of AMD ATI) start 21:59 / 22:01 need to restart (close) - result - GOOD
    Windows Installer wants to make changes - C:\window\SysWOW64\msiexec.exe/x {72736F5F-520 d - 472-A - 88 - 7 B 0 ERRRR it went away on its own.} Closing - 22:05 /qn REBOOT = really delete<---- came="" up="" again="" after="" cold="" start.="" think="" it="" had="" something="" to="" do="" with="" ati="" registration="" window.="">

    Install Google Chrome - result - GOOD

    Install Fusion - 2.0.1.117
    Install AMD OverDrive 3.2.1.0439 utility - Enable AMD Smart profiles -.
    Shutdown
    Power - result - GOOD
    Install the G15 - result - GOOD
    Install Windows Ventrilo 3.0.5 x 64-GOOD
    Install the Steam Client

    Install COD4MW2

    Change the settings to save energy for the computer to never sleep.
    22/05/2010
    Install gtalk, gApps
    Up to 08:57 05/22/2010 BSOD Mini dump.

    Dmp kernel that is renamed to 5222010857AMMEMORY. DMP

    BSOD more 2s on 2 days.

    Hello

    Check this thread for more information on using BlueScreenView, MyEventViewer and other methods of
    Troubleshoot the BlueScreens - top two responses.

    http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/8df6485a-50cc-4cdc-BE3E-0f05c7745117

    ===========================================

    The material is highly suspect!

    Since you reformatted and reloaded Windows this indicates that the problem is either material or a
    very basic pilot who has been reloaded - video/display, network/WiFi, sound, possibly 3rd party
    mouse or keyboard, BIOS, chipset and other low level drivers.

    This error is usually a driver problem and display adapter (video) driver is the most suspicious if she
    may be others. Antivirus/antispyware/security programs, equipment (heat) and major software problems
    can also cause the error. When you get to the section of the driver to use the Troubleshoot utility my generic
    methods in the next message and then return to the if necessary troubleshooting tool.

    Have you recently added hardware or drivers updated? Don't forget to look in Control Panel - Windows
    Updates to see if all drivers have been updated it. Other donor opportunities include the antivirus/anti-
    spyware/security programs.

    When you get to the pilot and sections of the memory of the troubleshooter check the following message to
    update drivers and memory test and then return to the troubleshooter if necessary.

    ------------------------------------------------

    Even if you have some of these here tried a fairly complete convenience store just in case.

    BCCode: 7F 0x0000007E

    Cause

    SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. To interpret it, you must identify which exception has been generated.

    Common exception codes are:

    • 0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred.

    For a complete list of exception codes, see the Ntstatus.h file located in the directoryInc. of the Microsoft Windows Driver Kit (WDK).

    Solve the problem

    If you do not have to debug this problem, you must use certain basic troubleshooting techniques.

    • Make sure you have enough disk space.
    • If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
    • Try changing video cards.
    • Check with your hardware vendor for updates to the BIOS.
    • Disable the BIOS memory options such as implementing caching or shading.

    If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.

    If exception code 0 x 80000003 occurs, a hard-coded breakpoint or assertion was hit, but the system was launched with the/nodebug. switch. This problem should occur infrequently. If it occurs repeatedly, make sure that a kernel debugger is connected and the system is booted with theSwitch/DEBUG .

    In case of exception code 0 x 80000002, the trap frame provides additional information.

    If you do not know the specific cause of the exception, consider the following questions:

    • Hardware incompatibility. Ensure that any new hardware that is installed is listed in the list of the products tested Microsoft Windows market.
    • Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.

    If a driver is listed by name in the bug check message, disable or remove that driver. Disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.

    If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the service by starting the computer by using the recovery and then Console by removing the offending system service file.

    Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x7E.

    You can also disable memory cache BIOS may try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.

    The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation. You can solve the problems of BIOS by upgrading the version of the system BIOS.

    BCCode: 7F 0x0000007E<-- read="">
    * 1141.html http://www.faultwire.com/solutions-fatal_error/System-thread-exception-not-HANDLED-0x0000007E-

    -----------------------------------------------------

    BCCode: 109 0 x 00000109

    Cause

    There are generally three different causes for this bug check:

    1. A driver has deliberately or inadvertently modified kernel of criticism or data code. Microsoft Windows Server 2003 with Service Pack 1 (SP1) and later versions of Windows for computers x 64 do not allow the kernel to be debugged, except through authorized hot patches from Microsoft. For more information, see policy patch for x 64 systems.

    2. A developer tried to set a normal kernel breakpoint using a kernel debugger which was not attached when the system is started. Normal breakpoints (bp) can be defined only if the debugger is attached to the start time. Processor breakpoints (ba) can be defined at any time.

    3. A physical corruption has occurred. For example, the kernel code or data could are stored in memory has failed.

    BCCode: 109 0 x 00000109<-- read="">
    * 1262.html http://www.faultwire.com/solutions-fatal_error/modification-of-System-Code-or-a-Critical-Data-0x00000109-

    --------------------------------------------------------------------------

    Look in the Event Viewer to see if something is reported on those.
    http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

    MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
    TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
    http://www.NirSoft.NET/utils/my_event_viewer.html

    -------------------------------------------------------------------------

    Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
    info that would help. Such as ITC and 4 others entered at the bottom left. And all others
    error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

    As examples:

    BCCode: 116
    BCP1: 87BC9510
    BCP2: 8C013D80
    BCP3: 00000000
    BCP4: 00000002

    or in this format:

    Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
    Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

    It is an excellent tool for displaying the blue screen error information

    BlueScreenView scans all your minidump files created during 'blue screen of death '.
    hangs and displays information about all accidents of a table - free
    http://www.NirSoft.NET/utils/blue_screen_view.html

    BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
    There are other causes.

    You can do mode if necessary safe or the Vista DVD command prompt or
    Options recovery if your system is installed by the manufacturer.

    How to start on the System Recovery Options in Windows 7
    http://www.SevenForums.com/tutorials/668-system-recovery-options.html

    You can try a system restore to a point before the problem started when one exists.

    How to do a system restore in Windows 7
    http://www.SevenForums.com/tutorials/700-system-restore.html

    -------------------------------------------------------------------------

    Follow these steps:

    Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to fix the system files of Windows 7 with the System File Checker
    http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates cbs.log Windows Vista (and Windows 7)
    http://support.Microsoft.com/kb/928228

    The log can give you the answer if there is a corrupted driver. (Says not all possible
    driver problems).

    Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

    How to run the check disk at startup in Windows 7
    http://www.SevenForums.com/tutorials/433-disk-check.html

    -------------------------------------------------------------------------

    Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
    keyboard and mouse, as well as of other major device drivers.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    Installation and update of drivers to 7 (update drivers manually using the methods above is preferable to ensure that the latest drivers from the manufacturer of system and device manufacturers are located)
    http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    -------------------------------------------------------------------------

    How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
    quit unexpectedly
    http://support.Microsoft.com/kb/958233

    Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
    http://www.chicagotech.NET/Vista/vistabluescreen.htm

    Understanding and decoding BSOD (blue screen of death) Messages
    http://www.Taranfx.com/blog/?p=692

    Windows - troubleshooting blue screen errors
    http://KB.wisc.edu/page.php?id=7033

    -------------------------------------------------------------------------

    In some cases, it may be necessary.

    Startup Options recovery or Windows 7 disk repair

    How to run a startup repair in Windows 7
    http://www.SevenForums.com/tutorials/681-startup-repair.html

    How to start on the System Recovery Options in Windows 7
    http://www.SevenForums.com/tutorials/668-system-recovery-options.html

    How to create a Windows 7 system repair disc
    http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

    How to do a repair installation to repair Windows 7
    http://www.SevenForums.com/tutorials/3413-repair-install.html

    I hope this helps.

    Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

  • blue screen error stop 0 x 00000019

    When my friend starts windows 7 on his computer after the signature she gets a blue screen and the codes only that I'm able to catch during the dump process are 0 x 00000019 before restarting the computer, this computer is ony around the age of 2 months, anyone know or have any ideas as to why this is happening?

    Hello

    On a new computer it should certainly contact support from the manufacturer of the system for known issues and
    claim of possible guarantee as well as their forums (if any). It's to fix more they
    pretend that it is something that the user did as the cause.

    ====================================

    If you want to solve the problem.

    This is most likely caused by a stray driver, although the antivirus/antispyware/security programs and
    memory/hardware are all the real suspects. See my update driver and memory by following test methods
    Message.

    BCCode: 19 0 x 00000019<-- read="">
    http://www.faultwire.com/solutions-fatal_error/bad-pool-header-0x00000019-* 1040.html? = date order

    ===========================================================

    Look in the Event Viewer to see if something is reported on those.
    http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

    MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
    TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
    http://www.NirSoft.NET/utils/my_event_viewer.html

    -------------------------------------------------------------------------

    Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
    info that would help. Such as ITC and 4 others entered at the bottom left. And all others
    error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

    As examples:

    BCCode: 116
    BCP1: 87BC9510
    BCP2: 8C013D80
    BCP3: 00000000
    BCP4: 00000002

    or in this format:

    Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
    Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

    It is an excellent tool for displaying the blue screen error information

    BlueScreenView scans all your minidump files created during 'blue screen of death '.
    hangs and displays information about all accidents of a table - free
    http://www.NirSoft.NET/utils/blue_screen_view.html

    BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
    There are other causes.

    You can do mode if necessary safe or the Vista DVD command prompt or
    Options recovery if your system is installed by the manufacturer.

    How to start on the System Recovery Options in Windows 7
    http://www.SevenForums.com/tutorials/668-system-recovery-options.html

    You can try a system restore to a point before the problem started when one exists.

    How to do a system restore in Windows 7
    http://www.SevenForums.com/tutorials/700-system-restore.html

    -------------------------------------------------------------------------

    Follow these steps:

    Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to fix the system files of Windows 7 with the System File Checker
    http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates cbs.log Windows Vista (and Windows 7)
    http://support.Microsoft.com/kb/928228

    The log can give you the answer if there is a corrupted driver. (Says not all possible
    driver problems).

    Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

    How to run the check disk at startup in Windows 7
    http://www.SevenForums.com/tutorials/433-disk-check.html

    -------------------------------------------------------------------------

    Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
    keyboard and mouse, as well as of other major device drivers.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista (also Windows 7) Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    -------------------------------------------------------------------------

    How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
    quit unexpectedly
    http://support.Microsoft.com/kb/958233

    Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
    http://www.chicagotech.NET/Vista/vistabluescreen.htm

    Understanding and decoding BSOD (blue screen of death) Messages
    http://www.Taranfx.com/blog/?p=692

    Windows - troubleshooting blue screen errors
    http://KB.wisc.edu/page.php?id=7033

    -------------------------------------------------------------------------

    In some cases, it may be necessary.

    Startup Options recovery or Windows 7 disk repair

    How to run a startup repair in Windows 7
    http://www.SevenForums.com/tutorials/681-startup-repair.html

    How to start on the System Recovery Options in Windows 7
    http://www.SevenForums.com/tutorials/668-system-recovery-options.html

    How to create a Windows 7 system repair disc
    http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

    I hope this helps.

    Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

  • Help to fix the blue screen error: STOP: 0x0000007A

    Original title: I get the BSOD on my Dell Inspiron 14 stop information is at the bottom.  What means this dose-specific code and how can I solve this problem?

    STOP: 0x0000007A (0xFFFFFFFFC0000056, 0x0000000058DB3860, 0xFFFFF8A000E42A48, 0xFFFFF960001E082C) he begins again each time after it happens like nothing ever happened, but I don't want my computer any crash if there is an easy way to understand what it means and set it would be nice.

    Hello

    Here are some of the more general methods that could help solve the problems of use as
    necessary (same as in the link below).

    Check this thread for more information using BlueScreenView, MyEventViewer and other methods
    to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

    http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system/sometimes-i-get-a-blue-screen-when-using-IE-8/c675b7b8-795f-474d-a1c4-6b77b3fcd990

    We can analyze the minidumps if make you it available to the SkyDrive or another file
    sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
    for the office or in the Documents folder and download them from there.

    ZIP or download the content of the C:\Windows\minidump

    Use SkyDrive to upload collected files.
    http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

    -------------------------------------------------------------------------

    Look in the Event Viewer to see if something is reported on those.
    http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

    MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
    TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
    http://www.NirSoft.NET/utils/my_event_viewer.html

    Here are a few ways to possibly fix the blue screen issue. If you could give the info to blue screen
    This would help. Such as ITC and 4 others entered at the bottom left. And another error
    information such as the STOP codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

    As examples:

    BCCode: 116
    BCP1: 87BC9510
    BCP2: 8C013D80
    BCP3: 00000000
    BCP4: 00000002

    or in this format:

    Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
    Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

    It is an excellent tool for displaying the blue screen error information

    BlueScreenView scans all your minidump files created during 'blue screen of death '.
    hangs and displays information about all accidents of a table - free
    http://www.NirSoft.NET/utils/blue_screen_view.html

    BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
    There are other causes.

    You can do mode if necessary safe or the Vista DVD command prompt or
    Options recovery if your system is installed by the manufacturer.

    How to start on the System Recovery Options in Windows 7
    http://www.SevenForums.com/tutorials/668-system-recovery-options.html

    You can try a system restore to a point before the problem started when one exists.

    How to do a system restore in Windows 7
    http://www.SevenForums.com/tutorials/700-system-restore.html

    -------------------------------------------------------------------------

    Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to fix the system files of Windows 7 with the System File Checker
    http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates cbs.log Windows Vista (and Windows 7)
    http://support.Microsoft.com/kb/928228

    The log can give you the answer if there is a corrupted driver. (Says not all possible
    driver problems).

    Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

    How to run the check disk at startup in Windows 7
    http://www.SevenForums.com/tutorials/433-disk-check.html

    -------------------------------------------------------------------------

    Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
    keyboard and mouse, as well as of other major device drivers.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    Installation and update of drivers under Windows 7 (updated drivers manually using the methods above
    It is preferable to ensure that the latest drivers from the manufacturer of system and device manufacturers are located)
    http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    -------------------------------------------------------------------------

    How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
    quit unexpectedly
    http://support.Microsoft.com/kb/958233

    Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
    http://www.chicagotech.NET/Vista/vistabluescreen.htm

    Understanding and decoding BSOD (blue screen of death) Messages
    http://www.Taranfx.com/blog/?p=692

    Windows - troubleshooting blue screen errors
    http://KB.wisc.edu/page.php?id=7033

    -------------------------------------------------------------------------

    In some cases, it may be necessary.

    Startup Options recovery or Windows 7 disk repair

    How to run a startup repair in Windows 7
    http://www.SevenForums.com/tutorials/681-startup-repair.html

    How to start on the System Recovery Options in Windows 7
    http://www.SevenForums.com/tutorials/668-system-recovery-options.html

    How to create a Windows 7 system repair disc
    http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

    How to do a repair installation to repair Windows 7
    http://www.SevenForums.com/tutorials/3413-repair-install.html

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

  • I get the blue screen error - error - Stop 0X0000008E

    -Stop error 0X0000008E (0xC00005, 0XC000005, 0X08244c8b, 0XBA50B58C, 0 X 00000)

    Hi I get the blue screen error - error - Stop 0X0000008E (0xC00005, 0XC000005, 0X08244c8b, 0XBA50B58C, 0 X 00000) and cannot use the pc in safe mode. I have XP - OS. I really don't want to reformat the HARD drive and you want to avoid reinstalling as much as possible

    Hi aromaveda,

    ·         Have you made changes on the computer?

    Follow these methods.

    Method 1: Follow the steps in the article.

    You receive a random "0x0000008E" error message on a blue screen in Windows XP

    http://support.Microsoft.com/kb/827663

    Method 2: Follow these steps:

    Step 1: Start the computer in safe mode and check if the problem persists.

    A description of the options to start in Windows XP Mode

    http://support.Microsoft.com/kb/315222

    Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is no conflict of software like clean boot helps you eliminate software conflicts.

    How to configure Windows XP to start in a "clean boot" State

    http://support.Microsoft.com/kb/310353

    Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

    After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

    (a) click Start, run.

    (b) type msconfigand click OK.

    (c) the System Configuration Utility dialog box appears.

    (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

    (e) when you are prompted, click on restart to restart the computer.

    Method 3: Follow the steps in the article to check the drive for errors.

    How to perform disk error checking in Windows XP

    http://support.Microsoft.com/kb/315265

    Note: If bad sectors are found in the hard drive, then it could try to fix this particular sector. If you have any data on that, it can get lost.

  • stop random blue screen error DRIVER_IRQL_NOT_LESS_OR_EQUAL STOP: 0X000000D1

    original title: stop random screen w/blue

    I need help to solve this problem. My system will freeze and then randomly crash if I run games, programs or just sitting idle. I took the fan and blew out the dust, etc... and still no better. The info I get blue screen are:

    DRIVER_IRQL_NOT_LESS_OR_EQUAL

    STOP: 0X000000D1

    nvstor.sys - address 83F42395

    Any help would be appreciated to gratly.

    Hello

    Here is a version of Vista of the troubleshooter that Dena referred:

    =================================================================

    Check this thread for more information on using BlueScreenView, MyEventViewer and other methods of
    Troubleshoot the BlueScreens - top 3 answers.

    http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

    -----------------------------------------------------------------------------------------------------------------

    Check with your manufacturer for newer drivers video card (special forces), known issues and
    other possible problems - check also the video card and game maker forums. It can even be
    a problem created by the interaction of two pilots (rather than the usual cause), perhaps the
    video driver and a swap file error and other causes work together to create the problem.

    ==============================================================

    Even if you have done some of these methods here is the complete troubleshooting tool while
    dealing with his need.

    Think video drivers especially if it may be others. Refer to the section of driver in my generic bluescreen
    methods of troubleshooting below. BIOS, low and antispyway/antivirus/security chipset drivers
    programs may also cause this. Check the resolution of the problems and when you get to the pilot and sections tests memory refer to the generic methods in the next message and then returns to the resolution of problems
    If necessary.

    BCCode: D1 0x000000D1

    Cause

    A driver tried to access a pageable (or that is completely invalid) address while the IRQL was too high.

    This bug check is usually caused by drivers who used a wrong address.

    If the first parameter has the same value as the fourth parameter, and the third parameter indicates a runtime operation, this bug check was probably caused by a driver who was trying to run code when the code itself has been paginated outside. The possible causes for the error page are:

    • The function was marked as pageable and was operating at an IRQL higher (including obtaining a lock).
    • The function call was made to a function in another pilot, and that this driver has been unloaded.
    • The function was called by using a function pointer that was an invalid pointer.

    BCCode: d1 0x000000d1<-- read="">
    * 1210.html? order = votes http://www.faultwire.com/solutions-fatal_error/Driver-IRQL-not-less-or-Equal-0x000000D1-

    =========================================

    Look in the Event Viewer to see if something is reported on those.
    http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

    MyEventViewer - free - a simple alternative in the standard event viewer
    Windows. TIP - Options - Advanced filter allows you to see a time rather
    of the entire file.
    http://www.NirSoft.NET/utils/my_event_viewer.html

    -------------------------------------------------------------------------
    Also this, so you can see the probable bluescreens.

    Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
    http://www.winvistatips.com/disable-automatic-restart-T84.html

    -------------------------------------------------------------------------

    Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
    info that would help. Such as ITC and 4 others entered at the bottom left. And all others
    error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

    As examples:

    BCCode: 116
    BCP1: 87BC9510
    BCP2: 8C013D80
    BCP3: 00000000
    BCP4: 00000002

    or in this format:

    Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
    Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

    It is an excellent tool for displaying the blue screen error information

    BlueScreenView scans all your minidump files created during 'blue screen of death '.
    hangs and displays information about all accidents of a table - free
    http://www.NirSoft.NET/utils/blue_screen_view.html

    BlueScreens many are caused by old or damaged, drivers particularly video drivers but it
    are other causes.

    You can do without if needed fail or the Vista DVD or recovery command prompt mode
    Options if your system was installed by the manufacturer.

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    You can try a system restore to a point before the problem started when one exists.

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

    -------------------------------------------------------------------------

    Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
    program generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    The log can give you the answer if there is a corrupted driver. (Says not all possible
    driver problems).

    Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    -------------------------------------------------------------------------

    Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
    keyboard and mouse, as well as of other major device drivers.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    -------------------------------------------------------------------------

    How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
    quit unexpectedly


    http://support.Microsoft.com/kb/958233

    Troubleshooting, STOP error blue screen Vista
    http://www.chicagotech.NET/Vista/vistabluescreen.htm

    Understanding and decoding BSOD (blue screen of death) Messages
    http://www.Taranfx.com/blog/?p=692

    Windows - troubleshooting blue screen errors
    http://KB.wisc.edu/page.php?id=7033

    -------------------------------------------------------------------------

    In some cases, it may be necessary.

    The Options or Vista recovery disk Startup Repair

    How to do a startup repair
    http://www.Vistax64.com/tutorials/91467-startup-repair.html

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    I hope this helps.

    Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

  • My Vista system crashes, blue screen on startup: irql_not_less_or_equal STOP: 0x0000000A (0 x 0, 00000002 00000001, 0x81AE8590)

    My Vista system was crushed, tried everything, but finally resorted to a recovery of the original factory image off the coast of the hard drive Partition. Everything seemed to go smooth but now I get a blue screen at startup: irql_not_less_or_equal STOP: 0x0000000A (0 x 0, 00000002 00000001, 0x81AE8590)

    Odd part is the system has two RAM slots, we have a 2 GB key and another has a 1 GB. Could not get the machine to start with two sticks in. Will start with a stick in each thin slot. Will not start no matter how they are installed if you are using the two RAM slots. Ran SFC/scannow. He found errors, that it cannot correct. How can I fix these errors?

    CBS log is large enough: what details should I post it to help you troubleshoot?

    Note: Were able to update the system, including the installation of updates Windows 128 and seems to be updated throughout the SP-2. I really don't want to run another recovery if possible.

    Thank you!

    Hello

    Perhaps you have different brands of RAM in your computer, and so it would not start with the two inserted Rams. Do a check for your specific PC memory that tells you what products work with your system.

    Follow the information in this article.
    Know what type of RAM you need

    In addition, updated BIOS.

    Warning of the BIOS:
    BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

    If scan SFC did not fix the issue, I would say that you follow the steps in this article to fix it.

    http://support.Microsoft.com/kb/929833

    Regarding blue screen errors, follow the steps in this article that applies also for Vista.

    Resolve stop (blue screen) error in Windows 7

  • How can I get rid of the blue screen error?

    Original title: Windows Vista Start does not

    Hello
    I have Windows Vista Home Premium, and I've had it for 5 years now (2006-) the problem is that I don't know what happened, but when it restarts, I have two options;

    Startup Startup Repair (recommended)
    Start Windows normally

    When I choose "Start Windows normally", a blue screen appears with an error message and disappears quickly, leading me to restart my Vista again. However, when I select Launch Startup Repair tool, it takes a while and after a bit, it ask if I want to send the error to microsoft (recommended) and I choose Yes, and it takes a little more time to look for a solution. Finally, a list of appropriate actions appear;

    Startup Repair; I tried this 8 times now, and he cannot find a solution, leading me to reboot once more.
    System restore; I tried ALL the dates of the restoration, and none of them worked. I got an error saying: it cannot restore.
    Restore the computer; 1. I don't have a backup drive (it's a shame, I know) and 2. I don't want back up and lose all my files.
    Windows Memory Diagnostic tools; I checked all hardware error, and none have been found.
    Command prompt; I don't know what to do with it.

    If someone can PLEASE help me, I would be VERY grateful. I have very old memories and photos on this computer and I don't want to lose these. I am begging for someone to help me, and my last priority would be to forget all these photos and files and move: (.) Oh and I tried running safe mode, by pressing F8 while the computer restarts and I've highlighted Mode safe mode with networking, but it gives a quick overview of a blue screen just and hangs on reboot. Please help me on the procedure to follow for the good of my IMPORTANT files and memories.

    Thank you, in advance.

    Hi AffanX,

    Method 1: Try to disable automatic reboot in the menu start-up advanced options, and then try to capture the blue screen error message, see the link below:

    Advanced-Startup-options-including-safe-mode

    http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode 

    Method 2: Disconnect all external devices (printers, scanner, USB (universal serial bus) readers, etc...)  Except the keyboard and mouse and then start.

    If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue.  Then get any drivers\software update for the device.

    After disconnecting all external devices, run the Startup Repair

    Windows Vista or Windows 7 unbootable and the Startup Repair tool does not resolve the problem
    http://support.Microsoft.com/kb/934540

    You can see the steps below for more information

    Resolve stop (blue screen) error in Windows 7

    http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

    (Article above applies to Windows Vista)

Maybe you are looking for

  • Pages on issues of formatting to iCloud

    Hey everybody, I created a document Pages using the Pages application on my macbook pro I downloaded then to iCloud Pages so that I can access it from any computer. The issue I'm having is that I formatted some of the text to have a black background

  • Satellite A300 PSAG0A - games does not show full screen

    I have a large number of games installed on my computer. At least 90% of them appear not in the size of the full screen, but they are displayed in a small window with a large amount of black screen that surrounds the window. I am running Windows Vist

  • Security and escrow accounts

    Hello my account has been blocked, so I want to be open so that I can place my calls...

  • Satellite M start because past HDD USB to disk storage

    I have tried changing the USB phone is stored in properties but changed the hard drive.Now computer will not load upward.

  • LABVIEW FOR LEGO MINDSTORMS

    Hello, I need help. Pls help me with motors to control Robots NXT with NXT buttons. I need change the power of the engines with NXT buttons. How do I achieve this function? Thank you very much for your answer! -In the attachment is the same program b