stop random blue screen error DRIVER_IRQL_NOT_LESS_OR_EQUAL STOP: 0X000000D1

Similar Questions

• [SOLVED] ATI HD series random blue screen error: error 0x0000007e ntoskrnl kb965494

  [Problems]

  Fixes random maps of BSOD blue screen of death ATI HD Series - spontaneous different random BSOD error codes every time

  Solves problems with his SoundBlaster X - FI (on board and add the map) extreme gamer - Sound sound seriously jerky or cut sharply off the coast

  Solves delays random system - system shuts down randomly for no apparent reason
  Solves the problems of disconnected Steam - quite noticeable in Call of Duty 4 Modern Warfare 2
  Resolved A of Call of Duty 4 Modern Warfare 2 in delays play random or falling of the game so that your game. Usually, when first start the game. Not having not NAT enable may cause a similar delay as well.
  [Source of problem]
  The problem is with an older driver a new loading equipment when you first load the operating system from Microsoft. Shame on you, Microsoft.  6 weeks to understand it and it is CLEARLY without Microsoft. Sorry, but none of the NDA here.
  Its a simple problem, yet almost impossible to find. Catalyst install Manager - ATI HDMI Audio Device will add an Audio device rather than to replace the device driver Audio HDMI Microsoft load the OS installation stage. Or the pilot is ignored all together because Microsoft has already loaded a driver installation for this device.
  [Clean Install FIX]
  When you install the ATI Catalyst 10.6, use the custom installation and exclude the HDMI Audio by unchecking the box next to the HDMI Audio. Pilots still end upward in the ATI Catalyst install directory if you can note the ATI installation path. The problem is that ATI will add an HDMI high definition audio device, DOES not replace the Windows device already loaded. Or may not charge a second device. Whatever it is, it uses the Microsoft device driver.
  Updated driver software with the driver - Microsoft high definition Audio Device driver ATI manually following the instructions below.
  [Windows OS already loaded FIX]
  -Device Manager-
  Manage driver updated using computer-> right click-> appliances-> sound-> right click HDMI high definition Audio Device-> update driver and browse to the directory of ATI (check include subfolders).
  Also noticed the BIOS default settings cause problems of NB and DRAM. Overclocked to mount pressure on the system. Even if I adjusted the settings of the BIOS, I have always many BSOD until I updated the driver for high definition Audio Device from Microsoft with the ATI driver.
  Ubuntu ran without a single question before changes to accommodate the Windows 7 operating system. For some reason any Windows is picky about certain parameters so that Ubuntu 10.04 LTS loads and runs without a single problem.
  I have the logs memory.dmp and mini.dmp. Any help and any help appreciated :D
  After running through the following steps, the problem here is the ntoskrnl.exe causing several bugs (BSODS). Even if it's a problem with Vista, this problem occurs with Windows 7.
  • Event ID: 1001 Source: error checking
    The computer was restarted after a bugcheck.  The bugcheck was: 0x0000007e (0xffffffffc0000005, 0xfffff88000e34294, 0xfffff880031bda18, 0xfffff880031bd280). A dump was saved in the: C:\Windows\MEMORY. DMP. Report ID: 052310-17316-01.

    The computer was restarted after a bugcheck.  The bugcheck was: 0 x 00000109 (0xb3b7465eeb217b7e, 0xfffff80002d18cc0, 0xa3a039d898a4a950, 0 x 0000000000000001). A dump was saved in the: C:\Windows\MEMORY. DMP. Report ID: 052110-23197-01.

  OS: Microsoft Windows 7 Ultimate 64 bit
  Antivirus: Microsoft Windows Security Essentials
  Motherboard: Gigabyte GA-890FXA-UD5
  RAM: 8 GB CORSAIR DDR3 4 GB 1333 MHz CORSAIR TW3X4G1333C9A TWIN

  Video: Diamond ATI Radeon HD5850 1 GB DDR5

  PROCESSOR: AMD X 4 965BE
  HD: Hitachi 1 TB HDE721010SLA330 S/N MS03G16K
  PS: Antec EarthWatt 750W PSU V2.3
  KB: Logitech G15
  Mouse: Razer Deathadder 3.5 G
  Gamepad: Belkin n52te
  First try to solve this problem:
  Fresh OS loaded and BSOD immediately after the restart. Reason or details is unknown because of the immediate reboot without a kernel image. No events logged in Windows event logs with error checking information.
  At ran Windows Update for the current patches. Random BSOD on restart.
  Load the ATI Catalyst 10.4 Suite for Windows 7 (64-bit). Random BSOD on restart.
  Problem again when the system is stopped and started. Chances are THAT BSOD will occur without emptying the core or the mini writing.
  Run the checker - 90% chance of BSOD
  Ran Check Disk - seems to be stuck on stage 4 'verification data file' 57531 63472 processed files. 01:05: PM 05/21/2010 FAIL stopped here 13:44

  Second attempt to solve this problem (low-level format):

  Using Hitachi tools - http://www.hitachigst.com/hdd/support/download.htm Drive Fitness Test - Switch BIOS from AHCI to IDE to access the SATA drive.
  Quick Test results - HDE721010SLA330 successfully completed / Disposition Code = 0x00
  Clear the result of the boot record - 0x00
  Wipe the drive (drive clean takes time for 1 to ~3.5 hours) / 17:07 Media Analysis / 20:20 hours of fact and change the outcome - success 0x00
  
  
  Updated the BIOS with F2 14/05/2010 (CPU compatibility improve)
  Press DELETE to enter BIOS F8 to enter the Q - Flash insert USB Thumb Drive (a drive if no floppy is in system) select the file
  Change the BIOS settings-
  Integrated Peripherals-
  OnChip SATA Type [Native IDE] change on [AHCI]
  (No Option for this) F6 for drivers to be loaded in Pre-os Windows 7 64 bit

  Install Windows 7 Ultimate 64 bit at 21:02 / Installer Reboot 21:14 / end of installation restart 21:18 / finalised result 21:21 - GOOD

  Install the driver USB 3.0 NEC 21:22 - result - GOOD
  Automatic update added KB978601 (pending reboot) and KB979309 - result - GOOD

  Install the network drivers Realtek Lan_win7 - result - GOOD

  Install win7_chipset (installed ATI Catalyst install manager 03.00.0765) 21:30 - result - BSOD KERNEL DUMP RENOWNED MEMORY. DPM at 5212010935PMMEMORY. DMP

  Hitachi configured disk requires reboot (stop for cold start) - 21:37 - result - connected

  Install Microsoft Windows Security Essentials 64 bits 21:43 d/l latest and scan / to 21:49 results - GOOD

  Shutdown - 21:51

  Power - result - GOOD

  Install ATI 10-4_vista64_win7_64_dd_ccc_wdm_enu (taken from the site of AMD ATI) start 21:59 / 22:01 need to restart (close) - result - GOOD

  Windows Installer wants to make changes - C:\window\SysWOW64\msiexec.exe/x {72736F5F-520 d - 472-A - 88 - 7 B 0 ERRRR it went away on its own.} Closing - 22:05 /qn REBOOT = really delete<---- came="" up="" again="" after="" cold="" start.="" think="" it="" had="" something="" to="" do="" with="" ati="" registration="" window.="">

  Install Google Chrome - result - GOOD

  Install Fusion - 2.0.1.117

  Install AMD OverDrive 3.2.1.0439 utility - Enable AMD Smart profiles -.

  Shutdown

  Power - result - GOOD

  Install the G15 - result - GOOD

  Install Windows Ventrilo 3.0.5 x 64-GOOD

  Install the Steam Client

  Install COD4MW2

  Change the settings to save energy for the computer to never sleep.
  22/05/2010
  Install gtalk, gApps
  Up to 08:57 05/22/2010 BSOD Mini dump.
  
  Dmp kernel that is renamed to 5222010857AMMEMORY. DMP

  BSOD more 2s on 2 days.

  Hello

  Check this thread for more information on using BlueScreenView, MyEventViewer and other methods of
  Troubleshoot the BlueScreens - top two responses.

  http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/8df6485a-50cc-4cdc-BE3E-0f05c7745117

  ===========================================

  The material is highly suspect!

  Since you reformatted and reloaded Windows this indicates that the problem is either material or a
  very basic pilot who has been reloaded - video/display, network/WiFi, sound, possibly 3rd party
  mouse or keyboard, BIOS, chipset and other low level drivers.

  This error is usually a driver problem and display adapter (video) driver is the most suspicious if she
  may be others. Antivirus/antispyware/security programs, equipment (heat) and major software problems
  can also cause the error. When you get to the section of the driver to use the Troubleshoot utility my generic
  methods in the next message and then return to the if necessary troubleshooting tool.

  Have you recently added hardware or drivers updated? Don't forget to look in Control Panel - Windows
  Updates to see if all drivers have been updated it. Other donor opportunities include the antivirus/anti-
  spyware/security programs.

  When you get to the pilot and sections of the memory of the troubleshooter check the following message to
  update drivers and memory test and then return to the troubleshooter if necessary.

  ------------------------------------------------

  Even if you have some of these here tried a fairly complete convenience store just in case.

  BCCode: 7F 0x0000007E

  Cause

  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. To interpret it, you must identify which exception has been generated.

  Common exception codes are:

  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred.

  For a complete list of exception codes, see the Ntstatus.h file located in the directoryInc. of the Microsoft Windows Driver Kit (WDK).

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques.

  • Make sure you have enough disk space.
  • If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.

  If exception code 0 x 80000003 occurs, a hard-coded breakpoint or assertion was hit, but the system was launched with the/nodebug. switch. This problem should occur infrequently. If it occurs repeatedly, make sure that a kernel debugger is connected and the system is booted with theSwitch/DEBUG .

  In case of exception code 0 x 80000002, the trap frame provides additional information.

  If you do not know the specific cause of the exception, consider the following questions:

  • Hardware incompatibility. Ensure that any new hardware that is installed is listed in the list of the products tested Microsoft Windows market.
  • Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.

  If a driver is listed by name in the bug check message, disable or remove that driver. Disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.

  If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the service by starting the computer by using the recovery and then Console by removing the offending system service file.

  Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x7E.

  You can also disable memory cache BIOS may try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.

  The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation. You can solve the problems of BIOS by upgrading the version of the system BIOS.

  BCCode: 7F 0x0000007E<-- read="">
  * 1141.html http://www.faultwire.com/solutions-fatal_error/System-thread-exception-not-HANDLED-0x0000007E-

  -----------------------------------------------------

  BCCode: 109 0 x 00000109

  Cause

  There are generally three different causes for this bug check:

  1. A driver has deliberately or inadvertently modified kernel of criticism or data code. Microsoft Windows Server 2003 with Service Pack 1 (SP1) and later versions of Windows for computers x 64 do not allow the kernel to be debugged, except through authorized hot patches from Microsoft. For more information, see policy patch for x 64 systems.

  2. A developer tried to set a normal kernel breakpoint using a kernel debugger which was not attached when the system is started. Normal breakpoints (bp) can be defined only if the debugger is attached to the start time. Processor breakpoints (ba) can be defined at any time.

  3. A physical corruption has occurred. For example, the kernel code or data could are stored in memory has failed.

  BCCode: 109 0 x 00000109<-- read="">
  * 1262.html http://www.faultwire.com/solutions-fatal_error/modification-of-System-Code-or-a-Critical-Data-0x00000109-

  --------------------------------------------------------------------------

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Follow these steps:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers to 7 (update drivers manually using the methods above is preferable to ensure that the latest drivers from the manufacturer of system and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials/3413-repair-install.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• M8330f - Blue screen - error DRIVER_IRQL_NOT_LESS_OR_EQUAL

  I bought a used computer m8330f multimedia center with a quad core AMD 2.2 GHz processor, Windows 7, 64 bit. Operating system.  When using my computer, I get a blue screen... DRIVER_IRQL_NOT_LESS_OR_EQUAL error with a message on: tcpip.sys , and then it is in emptying mode. Sometimes I get the error in netio.sys so.

  I read that some people suggest to delete the drivers and their reloading.  I don't know how to do and where I want to get the drivers for it.  Some say it's the network controller, need to install a new network adapter?

  Any suggestions would be greatly appreciated. Thank you.

  myfirecomputer wrote: thank you for your response.  Should I remove the drivers before installing this?

  Hello myfirecomputer, usually Nvidia drivers will install on the current drivers.

  The Nvidia download is an executable file, then simply click on the name of the file and it should run and install all the drivers that are included in the set of drivers.

• Random blue screen errors

  I use windows 8 64-bit on my laptop, and lately I've been doing bluescreen errors frequently.

  It says «DRIVER_IRQL_NOT_LESS_OR_EQUAL (NETIO.» (SYS) 'and when I restart the system, it displays' runtime error Visual C++ to not enough space for thread data ".» It happens sometimes and randomly in an interval of 10 minutes.
  Help, please.

  PA

  These were all linked to netio.sys and frequently when this happens, it is in fact linked to the application of malicious programs installed.  What do you use?

  Please run the driver verifier

  Driver Verifier (for full instructions, see our wiki here)

• Blue screen error: DRIVER_IRQL_NOT_LESS_OR_EQUAL

  The minidump file says that the error is related to the file tcpip.sys, the TCP/IP protocol driver.  How can I fix it?  I'm not too technically savvy, so please keep it simple :-)

  A few things can cause that. Download bluescreenview. Install, then run it. What to say? Try to open a prompt as an administrator (right mouse on it). Type sfc/scannow

• How can I stop the blue screen error caused by sffp_sd.sys

  Since the middle of the latest version of windows aprils has updated that I regularly get the blue screen... The last was 26/05/12 16:30...

  DRIVER_IRQL_NOT_LESS_OR_EQUAL

  STOP: 0X000000D1 (0X00000002, 0X00000000, 0X00000008, 0X914E8774)

  BTHUSB Device bthport.sys - 914E8774 address, base at 914E5000, Datestamp 4db03738

  Hello

  BTHUSB Device bthport.sys and sffp_sd.sys are the two components of Windows that means something else led him into
  Fault. First thing I would do is update the BlueTooth drivers. Check with the system manufacturer (mother's support-
  the Board Maker for systems (custom), their documentation online and drivers and ask in their forums (if any)
  known issues and/or / the real peripheral manufacturer support site. (See driver update methods in the next
  message.)

  ===============================================================================

  Pick up the pieces after a computer crash
  http://Windows.Microsoft.com/en-us/Windows-Vista/picking-up-the-pieces-after-a-computer-crash

  Check this thread for more information using BlueScreenView, MyEventViewer and other methods
  to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

  http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

  We can analyze the minidumps if make you it available to the SkyDrive or another file
  sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
  for the office or in the Documents folder and download them from there.

  ZIP or download the content of the C:\Windows\minidump

  Use SkyDrive download collected files and after shot/screenshot.
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  ==================================================================

  BCCode: D1 0x000000D1

  Think video drivers especially if it may be others. Refer to the section of driver in my credits
  methods of troubleshooting blue screen below. BIOS, chipset of low level drivers and
  antispyway/antivirus/security programs can also cause this. Check the resolution of the problems and
  When you arrive at the driver and tests of memory sections do reference to generic methods in following
  message and then back to the if necessary troubleshooting tool.

  BCCode: D1 0x000000D1

  Cause

  A driver tried to access a pageable (or that is completely invalid) address while the IRQL was too high.

  This bug check is usually caused by drivers who used a wrong address.

  If the first parameter has the same value as the fourth parameter, and the third parameter indicates a runtime operation, this bug check was probably caused by a driver who was trying to run code when the code itself has been paginated outside. The possible causes for the error page are:

  • The function was marked as pageable and was operating at an IRQL higher (including obtaining a lock).
  • The function call was made to a function in another pilot, and that this driver has been unloaded.
  • The function was called by using a function pointer that was an invalid pointer.

  
  BCCode: d1 0x000000d1<-- read="" this="">
  * 1210.html? order = votes http://www.faultwire.com/solutions-fatal_error/Driver-IRQL-not-less-or-Equal-0x000000D1-

  =========================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------
  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do without if needed fail or the Vista DVD or recovery command prompt mode
  Options if your system was installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• I get the blue screen error - error - Stop 0X0000008E

  -Stop error 0X0000008E (0xC00005, 0XC000005, 0X08244c8b, 0XBA50B58C, 0 X 00000)

  Hi I get the blue screen error - error - Stop 0X0000008E (0xC00005, 0XC000005, 0X08244c8b, 0XBA50B58C, 0 X 00000) and cannot use the pc in safe mode. I have XP - OS. I really don't want to reformat the HARD drive and you want to avoid reinstalling as much as possible

  Hi aromaveda,

  ·         Have you made changes on the computer?

  Follow these methods.

  Method 1: Follow the steps in the article.

  You receive a random "0x0000008E" error message on a blue screen in Windows XP

  http://support.Microsoft.com/kb/827663

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode and check if the problem persists.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is no conflict of software like clean boot helps you eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 3: Follow the steps in the article to check the drive for errors.

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Note: If bad sectors are found in the hard drive, then it could try to fix this particular sector. If you have any data on that, it can get lost.

• Blue screen error - recovery problem (STOP: 0 x 00008086)

  I am working on a Toshiba Satellite laptop and need to recover to original state. I have no recovery disks, however, I followed the Toshiba 'How' instructions (F8, and then select repair your computer), it displays the progress of Windows bar then goes to a black screen for a while and then I get a blue screen error (STOP: 0 x 00008086).

  Is there a way to get around this?

  N ° if drive HARD recovery cannot start on the regular basis there is no trick to make it work.

  To the factory settings, you need Toshiba DVD recovery.

• Blue Screen error code RQL_Less_or_Equal stop: 0X0000000A, C0xE10039F0, 0x000000FF, 0x00000000, 0x8056CA2E

  I came to doday to find that a blue screen on my pc .This is the error number.

  Blue Screen error code RQL_Less_or_Equal stop: 0X0000000A, C0xE10039F0, 0x000000FF, 0x00000000, 0x8056CA2E

  Please provide additional information on your system:
  What is your system brand and model?
  What is your version of XP and Servie Pack?
  Describe your current antivirus and software anti malware situation: McAfee, Norton, Spybot, AVG, Avira!, Defender, ZoneAlarm, PC Tools, MSE, Comodo, etc..
  Click Start, run and enter in the box:
  Msinfo32
  Click on OK and when the system info summary appears, click on Edition, select all, copy, and then paste the information here.
  For information about video drivers, expand components, click view, click on edit, select all, copy and then paste the information here.
  There will be some personal information (such as the user name and the name of the system), and everything seems
  be personal information for you, just delete pasted information.
  This will minimize back Q & A and eliminate guesswork.
  Download BlueScreenView here:
  http://www.NirSoft.NET/utils/blue_screen_view.html
  Unzip it and run it (BSV installs nothing) and let him complete the digitization of all of your files to dump.
  If you double-click on depressed, you will get information on it (including the field caused by the driver) and you should be able to spot the problem right away - especially if you see a model in landfills where Caused by field pilot is the same (beginning with this driver).
  Select (highlight) one or more of the most recent dump files by clicking on them and hold down the CTRL key to select multiple files.  Try to select only the most recent links that relate to your problem (perhaps five or six to start dump files).
  Click on file, save selected items and save information from the dumps to a text file on your desktop called BSOD.txt.  Open BSOD.txt with a text editor, copy the text and paste it in your next reply.
  Here's an example of report ASB to a single BSOD I initiated on purpose that indicates the cause of the accident as the pilot i8042prt.sys belonging to Microsoft Corporation:
  ==================================================
  Dump file: Mini062110 - 01.dmp
  Crash time: 21/06/2010-11:51:31
  Bug Check String: MANUALLY_INITIATED_CRASH
  Bug check code: 0x000000e2
  Parameter 1: 0x00000000
  Parameter 2: 0x00000000
  Parameter 3: 0x00000000
  Parameter 4: 0x00000000
  Caused by the driver: i8042prt.sys
  Caused by the address: i8042prt.sys + 27fb
  Description of the file: i8042 Port driver
  Product name: Microsoft® Windows® Operating System
  Company: Microsoft Corporation
  File version: 5.1.2600.5512 (xpsp.080413 - 2108)
  Processor: 32-bit
  Computer name:
  Full path: C:\WINDOWS\minidump\Mini062110-01.dmp
  ==================================================
  Send information from 5 last memory dumps.
  While you wait for analysis, no matter what you use for protection against malware, please follow these steps:
  Download, install, update and do a full scan with these free malware detection programs:
  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/
  It can be uninstalled later if you wish.

  Do not guess what the problem might be - understand and resolve it. I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!

• System unexpectedly stop restart and go to the blue screen "error code 0141.

  Original title: error code

  my lap top is suddenly happened to bluescreen, shut down and then after reboot, one, (error code 0141), appears. can you please tell me how to fix this?

  Hello

  Thank you to contact the community Microsoft and we will be happy to help you with your concern.

  According to the description, it looks like you have a problem with Windows Vista, getting automatically restart with a blue screen.

  He would be grateful if you can answer this question in order to help you further.

  1. have you made changes on the computer before this problem?
  2 what happens while accessing any special request or programs?

  I suggest you to check the information contained in the event logs? (Event Viewer)

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-information-appears-in-event-logs-Event-Viewer

  Perform a clean startup will check if any third-party application is causing the problem, as the clean boot helps eliminate software conflicts.

  How to solve the problem by running the clean boot in Windows vista: http://support.microsoft.com/kb/929135

  Note: Once you have completed troubleshooting, perform the steps in the step 3: to reset the computer as usual.

  I suggest you to see the steps in the following Microsoft article and check if it helps.

  How to fix a blue screen stop errors that cause Windows Vista to shut down or restart unexpectedly: http://support.microsoft.com/kb/958233

  Resolve stop (blue screen) errors in Windows 7 (similar to a few steps of the mentioned below, the section applies to windows vista): http://windows.microsoft.com/en-US/windows7/Resolving-stop-blue-screen-errors-in-Windows-7

  Notes:

  When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

  Before you perform the upgrade installation, I recommend you back up your files using windows backup.

  We would be more than happy to help you if the steps above did not solve the problem.

• Help? Computer stops, managed Kernel_Mode_Exception_Not blue screen error message

  My computer shuts down when I start it in the morning. I get the following error message KERNEL_MODE_EXCEPTION_NOT HANDLED with 0x10000008e and 0x5dd2952d error code and driver-induced Win32k.sys can someone please help? I tried restoring it does not work. I checked the memory without errors. Only checked the material no error. I have not recently installed the new drivers. What is a Microsoft update that is causing the problem?

  Thanks for any help.

  Hello

  Thank you for writing to Microsoft Communities. I understand how it could be frustrating when things do not work as expected. Please, I beg you, don't worry I'll try my best to resolve the issue.

  1. are you able to boot into Normal mode?

  I suggest to follow the steps provided and check if it helps.

  Method 1:

  Step 1: I suggest to disconnect all external devices other than the keyboard and mouse, then check if you receive the same error.

  If you receive, I suggest you follow step 2.

  Method 2:

  Step 1: Try to start the computer in safe mode and check if the same problem occurs:
  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Step 2: If the issue does not exist in Mode safe mode then try to put your computer in a clean boot state.

  By setting your boot system minimum state helps determine if third-party applications or startup items are causing the problem.

  http://support.Microsoft.com/kb/929135

  Note: After the troubleshooting steps, see step 3 of the binding of boot is a way of putting your computer to normal startup mode.

  Method 3: Also, try the steps in the following Microsoft article and check if it helps.

  Resolve stop (blue screen) error in Windows 7:

  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  For reference:

  Bug Check 0x1000008E: KERNEL_MODE_EXCEPTION_NOT_HANDLED_M: http://msdn.Microsoft.com/en-us/library/ff557203%28V=vs.85%29.aspx

  I hope it helps. If you have problems in the future, please let us know. We will be happy to help you

• "blue screen error" stop 0x0000003e "appeare

  "blue screen error" stop 0x0000003e "appeare

  Bug Check 0x3E: MULTIPROCESSOR_CONFIGURATION_NOT_SUPPORTED

  This indicates that the system has multiple processors, but they are asymmetric in relation to the other.

  Cause

  To be symmetric, all processors must be of the same type and level. This system contains processors of different types

  You use different processors on your system of MP.

  "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

• Blue screen error STOP: 0x0000000A

  STOP: 0x0000000A irql not less or equal bvluescreen 1055 whats up?

  What's new?

  Hello

  See this thread for more information on using BlueScreenView, MyEventViewer and other methods of
  Troubleshoot the BlueScreens - top two responses.

  http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/8df6485a-50cc-4cdc-BE3E-0f05c7745117

  ==============================================

  References to Vista also apply to Windows 7.

  Drivers could be at fault, however the problems of disk or security/antivirus/antispyware products are
  just as likely to be the root cause that they can force a driver to corrupt or go out of bounds.
  The video driver or something affecting it would be questionable.

  At the end of this message, I'll post a bluescreen generic and in the next convenience store
  How do to update the drivers and BIOS but also to check memory message.

  -----------------------------------

  BCCode: 0a 0x0000000A

  Cause

  This bug check is issued if the memory paged (or invalid) is accessible when the IRQL is too high.

  The error that usually generates this bug check occurs after the installation of the faulty device driver or service system, BIOS.

  If you encounter a bug 0xA control during the upgrade to a later version of Windows, this error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version.

  Solve the problem

  If a kernel debugger is available, get a stack trace.

  To resolve an error caused by the faulty device driver or service system, BIOS

  1. Restart your computer.
  2. Press F8 to character-based menu that displays the choice of operating system.
  3. In the WindowsAdvanced Options menu, select last known good Configuration . This option is most effective when a pilot or a service is added at a time.

  To resolve an error caused by an incompatible device driver, system service, virus scanner, or backup tool

  1. Check the system log in Event Viewer for error messages that may identify the device or driver that caused the error.
  2. Try disabling the cache in memory of the BIOS.
  3. Run the diagnostics of equipment provided by the manufacturer of the system, in particular the scanner memory. For more information about these procedures, see the manual of your computer.
  4. Make sure that the latest Service Pack is installed.
  5. If your system has cards (SCSI) small computer system interface, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination.
  6. For devices (IDE) peripheral electronic integrated, set the built-in as only primary IDE port. Also, check each IDE device to the right setting master/slave/stand alone. Try to remove all IDE devices except for the hard drives.

  If the message appears during installation of Windows, make sure that the computer and installed devices are listed in the list of the products tested Microsoft Windows market.

  Comments

  Before upgrading to a new version of Windows, remove all third-party device drivers and system services and disable any antivirus. Contact software manufacturers for updates of these third-party tools.

  BCCode: 0a 0x0000000A<-- read="">
  * 1025.html http://www.faultwire.com/solutions-fatal_error/IRQL-not-less-or-Equal-0x0000000A-

  ==================================================================

  General troubleshooting BlueScreen to use with the methods above.

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers to 7 (update drivers manually using the methods above is preferred
  to make sure that the latest drivers from the manufacturer of system and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• blue screen error stop 0 x 00000019

  When my friend starts windows 7 on his computer after the signature she gets a blue screen and the codes only that I'm able to catch during the dump process are 0 x 00000019 before restarting the computer, this computer is ony around the age of 2 months, anyone know or have any ideas as to why this is happening?

  Hello

  On a new computer it should certainly contact support from the manufacturer of the system for known issues and
  claim of possible guarantee as well as their forums (if any). It's to fix more they
  pretend that it is something that the user did as the cause.

  ====================================

  If you want to solve the problem.

  This is most likely caused by a stray driver, although the antivirus/antispyware/security programs and
  memory/hardware are all the real suspects. See my update driver and memory by following test methods
  Message.

  BCCode: 19 0 x 00000019<-- read="">
  http://www.faultwire.com/solutions-fatal_error/bad-pool-header-0x00000019-* 1040.html? = date order

  ===========================================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Follow these steps:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista (also Windows 7) Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Help to fix the blue screen error: STOP: 0x0000007A

  Original title: I get the BSOD on my Dell Inspiron 14 stop information is at the bottom.  What means this dose-specific code and how can I solve this problem?

  STOP: 0x0000007A (0xFFFFFFFFC0000056, 0x0000000058DB3860, 0xFFFFF8A000E42A48, 0xFFFFF960001E082C) he begins again each time after it happens like nothing ever happened, but I don't want my computer any crash if there is an easy way to understand what it means and set it would be nice.

  Hello

  Here are some of the more general methods that could help solve the problems of use as
  necessary (same as in the link below).

  Check this thread for more information using BlueScreenView, MyEventViewer and other methods
  to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system/sometimes-i-get-a-blue-screen-when-using-IE-8/c675b7b8-795f-474d-a1c4-6b77b3fcd990

  We can analyze the minidumps if make you it available to the SkyDrive or another file
  sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
  for the office or in the Documents folder and download them from there.

  ZIP or download the content of the C:\Windows\minidump

  Use SkyDrive to upload collected files.
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  -------------------------------------------------------------------------

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  Here are a few ways to possibly fix the blue screen issue. If you could give the info to blue screen
  This would help. Such as ITC and 4 others entered at the bottom left. And another error
  information such as the STOP codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers under Windows 7 (updated drivers manually using the methods above
  It is preferable to ensure that the latest drivers from the manufacturer of system and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials/3413-repair-install.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">