blue screen with 0xc00000f at 1 startup

Similar Questions

• WANT to PC dv7: at startup, I get a blue screen with a :( Your PC has encountered a problem and needs to restart.

  While I was using my laptop I received a message that HP was running some sort of program disagnostic and in the end, he asked if I wanted to repair the problems. I declined the offer. However, the next time I turned on the computer, I saw the first time the HP logo, then the message "automatic repair Preparation". After a few seconds there is a short rectangle that flashes on and disappears. Then I got a blue screen with: your PC encountered a problem and needs to restart. We will restart for you. "Who starts a blue screen and reboot cycle. Blue screens replacement error messages saying: "If you want to learn more, you can search online for later for this error" and once it will say 'FAT file system' and once 'NTFS file system. I have spent to support HP dv7 ENVY page and tried the suggestions of repair without success. Is it possible to go beyond these two error messages and their blue screens to get my system working again? If so, how?

  Hello

  Error code 24 characters is a failure of the short test (DST) disk Self and would indicate that hard is defective and must be replaced.  It is also consistent with your description of the problem.

  If your laptop is still under warranty, contact HP and arrange for the disk replaced - if necessary, you can check the status of your warranty here.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  If you are no longer under warranty, it's a fairly simple procedure to replace the HARD drive yourself - a brief guide on this is below.

  Readers on the following links are examples that would be perfect for your laptop.

  Hard drive 500 GB

  750 GB hard drive.

  1 TB laptop hard drive.

  The procedure to replace the hard drive begins on Page 56 of your maintenance & Service Guide.

  About reinstalling Windows 10 on new HARD drive, as long as the previous installation of Windows 10 had activated Ok after upgrading to Windows 7/8.1, you can simply create your own Windows 10 installation media and perform a new installation as described in the guide on the following link.  Note: On the activation screen, select "I have not a product key" - Windows will activate automatically once installation is complete.

  http://www.howtogeek.com/224342/how-to-clean-install-Windows-10/

  Kind regards

  DP - K

• Satellite A350 - blue screen with error message

  At the start of windows7, I get a blue screen with error message 0 x 0000116.

  Can someone help please?

  It looks like a graphics driver is a troublemaker. Try to reinstall a graphics driver in SafeMode (f8 at startup). Read this article for more information:

  http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/eb584685-6b8b-4ad7-B6CC-ae5ee78095fb

  It is for VISTA but should be the same for win 7 too.

• Wallpapers flashes a blue screen with a desktop screen

  Product: HP ENVY TouchSmart 15 t-j000 Select Edition CTO Notebook PC, model C9G48AAR, product number: C8P45AV
  Problem: Once connected, the screen flashes start screen randomly and does not respond to any input.
  Effort: We followed the instructions on the HP web site for this symptom (desktop screen will Flash between a blank blue screen with a task bar and a desktop on startup (Windows 8) computer screen), but it failed at step 8 - start screen flashes in Mode safe mode with no way to find or enter step "Control Panel." We have also restored the system to the last restore point, reinstall the memory and reset the BIOS - all the HP recommended processes for video problems.
  Current situation: we have yet to solve problems via the web HP site first; This has left us speechless. We went to the "Contact HP" to discuss with the service agent, but discovered that our warranty expired a week ago. We were directed to the help forum. The laptop is my son and is used for his college course. We need to help, you can provide as quickly as possible. Thank you!

  I have advanced and complete steps 8-14 in the correction procedure from HP, including the center of the Action to "never check solutions" are reduced to problem reports. Then we went ahead and made the Microsoft Updates that were pending since we had it restored to a previous restore point. So far so good! The flashing screen problem is not returned. Until that Microsoft published a fix for this problem, I think that bypass it HP will keep us to leave. Thank you!

  Could I ask a favor? A HP contact named Mason was initially to help us with this problem, but all attmepts to repsond to his e-mails ended in a failure to deliver ("Diagnostic - code 554).

  Case No.: 3008737217
  Mason
  Case manager
  Team of HP AMS TCO

  Can you communicate with him and let him know that the problem has been solved successfulkly? Thank you!

  Warn the looks!
  Bryan

• Blue screen with STOP error 0x0000007B (0xBA4CF524, 0xC0000034, 0x00000000, 0x00000000)

  I have my Acer 5920 laptop, 2 GB of RAM and 160 hard drive, last stop system time correctly with all the files to day, but when I restart then comes windows XP Jean-Christophe and then a blue screen with the error. Nor I have install new software or remove something in the laptop. My system was perfect, and that was before the last stop.
  I have Windows XP SP2-teacher-pack. I have the original CD of this package.
  But when I use the CD then nothing is happen and come same messgae of error. I do not have any other CD bootable for windowXP except your originalCD.
  Please suggest me what I should do to fix my probem. I'm not to much expert for the formatting and other things computer.

  After reading your following suggession:
  Here are a few things to try:
  The first thing to do is to boot your system and start pressing F8 as soon as it starts booting.  You will get the Windows startup options screen.  Select "Disable automatic restart in the event of system failure" and let it restart.  When it starts, it can now stop with an error screen and give an error message and code.

  Disconnect all external devices (printers, USB Hub, drives external, etc.) and try to start.

  I got the result of the error that comes on a blue screen after you follow your process-blue screen with STOP error 0x0000007B (0xBA4CF524, 0xC0000034, 0x00000000, 0x00000000)

  Thanks in advance for help
  What about nice Rajneesh

  Just one quick response for others...

  Go to your bios to change the mode of training of your s - ata AHCI or IDE Compatible mode or all that apply :) Windows XP is not like SATA, because it has no native support for it. At the start of the second phase of a Setup program, it would fail with this BSOD.

  Also read the following Microsoft article that describes many other causes (including file system damage):Troubleshooting of errors "Stop 0x0000007B" in Windows XP Advanced

  Sometimes, your BIOS will provide its default settings after a system crash or a configuration. Should not happen, but it is...

  For BIOS-discussions, see: 0x0000007B 0xBA4cf524 - Forum of Support PC - Free Computer help , XP installation: * STOP: 0x0000007B (0xF78D2524, 0xC0000034, 0x00000000, 0x00000000)? - Page 4 - Cyber Tech Help Support Forums , 0x0000007B (0xBA4CF524 - Google zoeken .)

  Have fun, and... Peace!

  Devvie

  ~ ~ ~ * E-mail address is removed from the privacy * ~ ~ ~

  CONARE nullius momenti videri fortasse missilibus careant
  ------
  All the spelling mistakes are my own and may not be distributed under the GNU General Public License! -(© 95 1 by Coredump; 2-10 by DevNullius)

• Blue screen with STOP: 0x0000007E (0xc0000005, 0 x 00000066, 0xba4dbc40, 0xba4db93c)

  How to fix blue screen with STOP: 0x0000007E (0xc0000005, 0 x 00000066, 0xba4dbc40, 0xba4db93c)

  These accidents were caused by the corruption of memory (probably a driver).  Run these two tests to check your memory and find which driver is causing the problem.

  If you are overclocking reset all default before running these tests.
  In other words STOP!

  1 - Memtest.

  * Download a copy of Memtest86 and burn the ISO to a CD using Iso Recorder or another ISO burning program. "http://www.memtest.org/#downiso"] Memtest86 + - Advanced Memory Diagnostic tool

  * Boot from the CD and let it run at least 5 or 6 passes.

  Remember, anytime Memtest reports errors, it can be bad RAM or a bad motherboard slot.

  Test the sticks individually and if you find a good, test it in all slots.

  Any error is indicative of a memory problem.

  If a well-known stick fails in a slot of motherboard, it's probably the slot.

  http://www.SevenForums.com/tutorials/105647-RAM-test-Memtest86.html

  2. Driver Verifier

  Using Driver Verifier is a dubious proposition. Most of the time it will crash and it will tell you what is the driver. But sometimes it will crash and will not tell you the driver. Sometimes it will crash until you can connect to Windows. If you can't mode without failure, then you will have to resort to editing the registry offline to disable driver verifier.

  I suggest that you first back up your data and make sure you have access to another computer so you can contact us in case of problems. Then do a system restore point (so you can restore the system using the functionality of Vista/Win7 Startup Repair).

  In Windows 7, you can do a startup repair disk by clicking Start... All programs... Maintenance... Create a system - with Windows Vista repair disc, you need to use your drive installation or from the "Repair your computer" option at the top of the Safe Mode menu.

  So, here is the procedure:
  -Go to start and type "auditor" (without the quotes) and press enter
  -Select 'Create a custom settings (for code developers)' and click 'Next '.
  -Select "Select individual settings from the list complete" and click "Next".
  -Select the entire document except for "Low resource Simulation" and click "next".
  -Select "Select driver names from a list", then click "next".
  Select all drivers that are NOT provided by Microsoft, and then click "Next".
  -On the next page, select "Finish".

  Restart the system and wait as he crashed to blue screen. Continue to use your system normally and if you know what are the causes of the crash, do it several times. The objective here is to get the system crash because Driver Verifier is stressing out the drivers. If it is not planted for you, then let it run for at least 36 hours of continuous operation (an estimate on my part).

  If you are unable to Windows because it crashes too early, try safe mode.
  If you can't mode without fail, try to use the system from the installation DVD restore to bring the system back to the previous point of restoration that you created.
  http://www.SevenForums.com/tutorials/101379-Driver-Verifier-enable-disable.html

  Further reading
  "http://support.microsoft.com/kb/244617"] using Driver Verifier to identify issues with Windows drivers for users advanced

• I put the machine into hibernation and when I restarted, I got a blue screen with stop: 0 x 00000024. Restart gave a different stop error message: 0 x 00000050.

  Original title: Blue screen problems - Stop 0 x 24 and 0 x 50

  I'm not being updated hardware or software on my Dell Latitude D8380.

  I ran the Windows tool to check if the laptop is suitable for upgrading to Windows 7, but did not install any software.

  I put the machine into hibernation and when I restarted, I got a blue screen with stop: 0 x 00000024 (0x001902fe, oxba4f7948, 0xba4f7644, 0xb9d31ae8) ntfs.sys address b9d31ae8 base at bpcef000, datestamp h8025be5.

  Restart gave a different stop error message: 0 x 00000050(0xffffffff,0x00000000,0xba1bef42,0x00000000) i8042prt.sys address ba1bef42 base at ba1b8000, date stamp 48025c 67.

  Please can you help. Thank you, Sue Dixon

  Hello

  Step 1: Check if you are able to boot in safe mode. If you are able to boot into safe mode, and then try to perform the clean boot to safe mode and check.

  From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".

  Reference:

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. click on start and then click Run.
  2. type msconfig and click OK.

  The System Configuration Utility dialog box appears.

  3. click on the tab general, click Normal Startup - load all services and device drivers and then click OK.
  4. When prompted, click on restart to restart the computer.

  Step 2: Run the check disk hard disk command. (You will be able to try this step if you are able to start in safe mode or in normal mode with success)

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Let us know the status of the issue.

• I just bought a Logitech Web c110 camera and every time I try to install the installer crashes. Also, I was making the blue screens with different messages on them.

  Original title: how to find missing or corrupt files on windows xp pro

  I just bought a webcam logitech c110 and whenever I try to install the installer breaks down and I was doing the blue screens with different messages on them... How to scan for missing or corrupted files?  My brother-in-law has built this computer for me and I did not all disks for windows xp pro. system that is on it

  Hello

  1. you receive an error message while trying to install the webcam? If so, then post back the exact error message.
  2 are you able to install any other software?

  Try to capture the error message on blue screen and after return the exact error message. This could help us help you better.

  Step 1: Try to install the webcam software in clean boot state and check.

  From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".

  Reference:
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:
  1. click on start and then click Run.
  2. type msconfig and click OK.
  The System Configuration Utility dialog box appears.
  3. click on the tab general, click Normal Startup - load all services and device drivers and then click OK.
  4. When prompted, click on restart to restart the computer.

  Step 2: Look for error messages in the event viewer. If you find error messages after return the exact error message so that we can help you better.

  Reference:
  Using the event viewer
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/snap_event_viewer.mspx?mfr=true

  Understanding of event viewer
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/event_overview_01.mspx?mfr=true

  Procedure to view and manage event logs in Event Viewer in Windows XP
  http://support.Microsoft.com/kb/308427

• When I log on my computer its is open for a minute and then a blue screen with error lights up and stops him. I can only log in safe mode of network.

  When I log on my computer its is open for a minute and then a blue screen with error lights and him stops

  I can only log in safe mode of network.

  original title: blue screen error

  If you can properly connect mode without failure, you can use "msconfig" to toggle various programs that load at startup.  Finally, find the one that is causing your program to crash.

  "How to solve configuration errors by using the System Configuration utility in Windows XP"
    <>http://support.Microsoft.com/kb/310560 >

  "System Configuration Utility overview"
    <>http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/msconfig_usage.mspx?mfr=true>

  HTH,
  JW

• Blue screen with stop: 0 x 00000024 (0x84598f58, 0x84598c54, 0x001904aa, 0x8561df51)

  * Original title: I need help please

  I was given an old computer model of ky x n bc laws all im going to do is to type using office 2000... and it worked in food for 5 minutes now, I have a blue screen with stop: 0 x 00000024 (0x84598f58, 0x84598c54, 0x001904aa, 0x8561df51) in my research I found, it seems that I need a recovery disk for this computer did not come with a how can I do to get a... im also secretly hoping that it costs no stupid amounts of money since I'm on a fixed income... Thanks for your help guys o btw, I tried f8 it will o do now and then appears on the blue screen and f11 does not work

  Hello

  Repair and reinstall the information:

  Try a startup repair and / or a system restore using a Microsoft Vista DVD (to borrow a)

  Manufacturers recovery disks normally do not have Service Options; they are normally a relocation to the factory only settings option.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  You can contact your computer manufacturer and ask them to send you a set of recovery disks to reinstall.

  Most manufacturers have more available Vista recovery disks.

  If this happens, you may need to try this instead:

  You can also borrow and use a Microsoft Vista DVD, which contains the files for the different editions of Vista (Home Basic, Home Premium, Business and Ultimate) must be installed. The product key on your computer / Laptop box determines what Edition is installed.

  Other manufacturers recovery DVDs are should not be used for this purpose.

  And you need to know the version of 'bit' for Vista, as 32-bit and 64-bit editions come on different DVDs

  Here's how to do a clean install of Vista using a DVD of Vista from Microsoft:

  "How to do a clean install and configure with a full Version of Vista '

  http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

  And once the operating system is installed, go to your computer manufacturer's website and get the latest drivers for your particular model or laptop computer.

  And phone Activation may be necessary when you use the above installation method.

  "How to activate Vista normally and by Activation of the phone '

  http://www.Vistax64.com/tutorials/84488-activate-Vista-phone.html

  See you soon.

• Blue screen with the error "irql_not_less_or_equal"

  I have a problem I can not correct and hoped someone could help me fix.

  I got a blue screen while I was working on my laptop. I restarted windows and once connected, the office appeared and everything seemed ok, but before I could do anything that I got another blue screen with the error "irql_not_less_or_equal" So now, I have only access in safe mode.

  I tried to restore the system to a previous point, but the same error occurred during windows startup.

  Then I made a backup of my files and tried to use the disk to reboot, but again, I got a blue screen (I don't remember the excact error) after the first loading bar, so noting changed.

  Then I looked at the log files and found that, just before the first crash, an adobe update has been installed. I removed adobe list startup failed, completely remove the adobe doesn't either.

  Also, in safe mode I don't have an internet connection (without wire or cable). Blue screen errors is not always the same, esspesially codes "stop".

  My knowledge of windows is very bad, so I just tried things people recommended on internet. If someone could help me would be great. I deleted all my important files from my laptop so I don't mind lossing just as long as windows functiones correctly again.

  Thank you

  King

  Sorry, but there are way too many mistakes even describe.  You have about 5000 errors of Avast.  I would like to delete it

  

• blue screen with * STOP: 0x000000A5 (0x0001000A, 0x00000000, 0x00000000, 0x00000000)

  HP Pavilion Elite PC m9150f

  Windows 7

  When I try to start my computer, I get a "Windows Error Recovery" screen and two choices of "Launch Startup Repair (recommended)" and "Start Windows normally".  No matter that the one I chose, I get a blue screen with "* STOP: 0x000000A5 (0x0001000A, 0x00000000, 0x00000000, 0x00000000).  I can't go any further.  Then I turn off the computer.

  I restart the computer and choose F9-Diagnotics.  When it opens.  I see that the test of memory has failed and has an error code of "BIOME-1" and the suggestion of "Please contact HP Support".

  Before all that happens, I reinstalled an antivirus program that I have used for several years without any problems.

  So here I am.

  What should I do now?

  I would appreciate your help.

  Thank you.

  Chris

  Here is the user guide.  http://h10032.www1.HP.com/CTG/manual/c01152947.PDF

  Page 26 is the beginning of the "replacement memory.

• When I start the laptop with home premium, all I get is a blue screen with 'owner' in the middle. None of the arrows or connection etc... I just used last week and was allowed

  I start my HP laptop, just get clear blue screen with 'owner' in the middle.  I can't get out of this pic.  even when I turned off, he returns in this... cannot log in or anything

  Hello

  I suggest you to follow these steps and check if that helps:

  Method 1:
  Try to start the computer in safe mode and check if the same problem occurs:
  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Method 2:
  Try to perform the verification and startup repair if it helps:
  http://Windows.Microsoft.com/en-us/Windows-Vista/startup-repair-frequently-asked-questions

  It will be useful.

• MacBook Pro screen displays a blue screen with the vertical line

  Hi, I have a problem with my macbookpro. When I try to start, the gray screen load with the apple logo and then turn to blue screen with vertical crosshairs.

  It would be useful that you mentioned EXACT model/year of your MBP and the current OSX.

  Ciao.

• Toshiba 32P2400EE - blue screen with message mono

  I have a toshiba tv LED serial number 32P2400EE. Accidentally when you press a button on the remote, it shows only a blue screen with a message of mono on the upper left.

  Please provide assistance.

  Hallo

  Have you tried to resolve your TV back to factory settings?