Bluetooth problem and overheating

Similar Questions

• Satellite A500-1GL - graphic card problem and overheating

  TOSHIBA SATELLITE A500-1GL - I almost year.
  Already, the first problem appeared immediately after the purchase.
  After a telephone conversation with the service and install some problem driver disappeared but unfortunately it was another, computer laptop start overheating especially on games but evan on movies more make strange noise.
  I ve already used about 7 different cooling pads but none of them helped, I change the fan settings, cleaning by compressed air did not help at all.

  Is there a way I can fix this?

  Should I send it to Toshiba as it is still under warranty?

  Can you please tell us what is the first problem?
  To be honest, you should let Toshiba service to check this and give you 100% of mobile working.

  What you want to do? If the same symptoms are there even if laptop with factory settings, I think it is certainly the issue of guarantee.

• GPS, Wifi and Bluetooth problems

  So I have an iPhone 6 running on IOS 9.3.4 and have had problems with the GPS and the strength of wifi connectivity and bluetooth for a while now.

  First of all, the GPS.  It does not work.  When I run the maps or google maps on my device and the input an address the app can give me a written plan, location, but will not show me on a map.  He'll start road to everywhere where I go and tell me to start position, for example, to the North on the road on that I am, but the arrow does not follow me and tell me when the turn or where I am.  Occasionally, he has a message of guidance down with a spinning wheel and then, after a few seconds, disappears.  I tried to reboot my device several times, I have reset the network setting, I reset all of the settings, I backed up my phone, reset it and recovered save him.  Nothing has worked.  I was at my local verizon store and received a 'new' (its definitely refurbished) phone and the problem persists on the new phone.  I reset the phone to factory setting without content, set up as a new phone and tried the cards again, thinking it might be a problem with the back to the top.  It still does not work.  I'm perplexed right now and do not know what to do/try.

  Second, wifi and bluetooth connectivity is terrible.  I can only receive a wireless signal so that in very close proximity with the router.  I tried to different houses/companies and it is the same question.  However, bluetooth is just as bad.  I use headphones wireless, and go to the gym/go for the route with them.  I used to be able to walk around the gym without my phone and have connected the headphones, but now I can't have my phone 2 feet of the appliance without the music being agitated (bad connection).  I'm really irritated that I cannot understand this point and that he can't seem to find a fixed solution online.

  If you have just updated to iOS 9.3.4, which I didn't even know still shone, so maybe it's a bug that comes with the update. However, your problems seem to follow a trend, you can not far from a source of connection and now a signal. It is perhaps because the necessary components for the Bluetooth, GPS and WiFi signal are damaged or defective. Have you dropped or spilled liquid on your iPhone recently?

• 6 s and Mazda Bluetooth problems iPhone

  Hi all, I have an iPhone 6s on 9.2.1 and a 2016 Mazda CX5 Grand Touring with a Bose stereo system. I'm having a problem when playing audio via Bluetooth (music to iTunes, podcasts, etc.) is of poor sound quality, the sound skips to come at random, and it cuts in and out a lot. I don't see a pattern, which means that it seems not cut or jump when there are notifications or other things happening on the phone. I have a Apple Watch, so I wonder if that might have something to do with it. I took the phone to the factory settings and had even Apple replace it entirely and I've set up as a new phone, without result.

  When I connect the iPhone to the car via USB, but it's not a solution either because I don't have these audio quality problems:

  (1) it always starts playing the same song, when I start the car - the first song in alphabetical order in my music library, and

  (2) Apple vocal cards don't play - it interrupts the podcast or lowers the volume of the music, but there is no voice of Siri giving directions.

  (3) if I plug the phone immediately when I start the car, it starts playing the radio at incredibly high volume, and then I have to manually select the USB.

  None of those are questions if I am connected via Bluetooth.

  I had this exact configuration of the watch/phone even on a Honda CRV from 2013 and connected to Bluetooth without any problem all the time I've owned this car. I took the Mazda dealer twice and they say it's a matter of the iPhone. Anyone have any ideas on what is happening and how I can fix this problem?

  Plugin problems you describe are a vehicle problem, and how the audio system controls the phone.

  The problem with Bluetooth, you said it worked in another vehicle. I understand that Mazda said it was a problem of the iPhone, but most audio problems have to do with the software in the audio system not done to support the version of Bluetooth on the phone. I take back the vehicle to the Mazda and ask if there is a software update to their audio system. You can also look around to see if they had complaints from other users in your area with this vehicle. You can also try to contact Mazda customer service and ask this question.

• Service error battery Bluetooth connection problem and "Bluetooth Control: an error occurred during initialization of this operation." Try restarting your computer or bluetooth device ".

  Original title: Bluetooth connection problem

  I have a bluetooth Jawbone headset which worked fine with my Dell studio 1458 until a month or two ago. I am running windows Home premium 64-bit. Now the device will connect is more to the laptop. I get an error to the stack service and "Bluetooth Control: an error occurred during initialization of this operation." Try restarting your computer or bluetooth device"I returned to you can restore point, but the issue is not resolved. All solutions?

  Hi Trainfan1,

  ·         Did you do changes on the computer before the show?

  Follow these methods.

  Method 1: Run the tool and troubleshooting hardware devices.

  Method 2: Check the drivers and the Bluetooth Support service.

  (a) click Start, type services in start search box and press enter.

  (b) Services for window open find Bluetooth Support Service and double-click it.

  (c) ensure that the service is both the value Automatic for Startup type and started for the State.

  (d) click Start, type Device Manager in the start search box and press enter.

  (e) to search for the Bluetooth device expand it and double click on the driver.

  (f) go to the tab driver and click set to update driver to update the drivers.

  (g) if the problem is still even try to Uninstall and reinstall the drivers in the same tab by clicking on the option Uninstall .

  Method 3: Remove all Bluetooth components and reinstall it from the manufacturer's Web site.

  Install all necessary software required for Bluetooth device work properly.

• Bluetooth problem on my new laptop HP Pavilion G series and really need help!

  I recently bought my new laptop and yesterday when trying to send a picture from my phone to it, files have not been sent, even though she said the phone and the laptop were connected, he mentioned something about Image push, but I am new to HP, so I'm not aware of what exactly is and desperately need help Please could someone help me with this, I would really appreciate that I could not yet send the file via bluetooth. Thanks in advance!

  D3,

  You said,

  "bluetooth device has not been successfully installed.

  You said,

  ""photo from my phone it it was settled, but it says ' unable to connect ' "." "

  I'm a little confused by what you say, but I do not understand 'unable to connect '.

  • It's time to go back to information I sent you and go through the installation program.
  • You can also use the HP connection manager to help you get the job done.

  Here is the Connection Manager software.  Download and install it.  Your computer already has the software, it's going to tell if the package will install...

  HP sp54945 V4.1.25.1 Connection Manager

  Once the software is installed...

  And you want to use the HP Connection Manager software.

  • Make sure that your wireless network is enabled,
  • Then look in your taskbar for your Connection Manager icon and
  • Double-click to start

  If you do not see the icon in the taskbar, you can do the following:

  Start > search / type "HP connect" >

  Click on 'Hp connection manager' when you see it in the start list

  This is a HP Connection Manager Help file.

  The document explains how to use the software to connect your Bluetooth devices (and wireless):

  Connecting to a network with the 4.x connection manager

  Good luck!

  ----------------------------------------------------------------------------------------------------------------

  When you appreciate the effort...

         Please click on the Star Bravo on the left to tell "thank you"! ""

      Is it solved? Make it easier for other people to find the answer:

  Please Mark my Post 'accept as Solution' to say "Yes!"

  Remember: the more information, help, best you , you can receive.

  Always include: (Notebook) product number , printer - model number ,.

  Operating system and a Description of the error

  Never give your serial number

  ----------------------------------------------------------------------------------------------------------------

  2012 the year of the Dragon!

• problem when installing bluetooth driver and software for windows 8

  I have a Samsung np355v5c-s05IN Laptop.I have windows 8 on my laptop pre-installed. Recently I reset my laptop then the Bluetooth driver and graphics software have been uninstalled. I got the software from Samsung which has helped me to install all the drivers and software is but he could not install the following Bluetooth and the driver. I have the software and the driver I tried to install manually but it was not original. I am enclosing pictures of errors. Please provide the solution for the same thing. I have a built-in Bluetooth of qualcomm atheros ar3012

  
  

  I found the solution. I uninstalled the unknown device in Device Manager. Then I deleted the bthport using cmd (Administrator). Then using the device manager that I scanned Bluetooth for windows and hardware changes automatically detected and installed the driver itself. But I want to know what was the main issue.

• 10 IOS leading to the Bluetooth problem

  Before download IOS 10, I've never known a Bluetooth problem when using my Ford truck.

  Now, when I get a call, the caller does not hear me and I can't hear the caller. If I have my phone in hand and I change the Bluetooth audio to the speaker of the iPhone or handheld and then change it back to my truck, it works very well.

  When I call my truck, using Bluetooth, all parties can hear one another, but incoming calls only on me.

  I tried to reset the network settings, non-couplage coupling phone/truck and restart the phone. Restarting seems to work for the next incoming call, and then it starts again.

  Any help would be great. I received an incoming call on my phone about 10 minutes before you download the update of IOS. The following call (update to the post), the problem is presented.

  Thank you.

  Try to get help from this article, get help to connect an accessory with your iPad, iPhone or iPod touch - Apple Support Bluetooth

• Satellite (PSK30E) L750 - bluetooth problem

  Given that the other thread is already closed and suggestions from here don't give me the help I must ask once again,

  I bought the version Satellite L750-PSK30E I have same questions regarding other bluetooth L750 problem.
  I installed Win 7 PRO - 64-bit, and after each installation driver, I could find under the list of drivers with intel, then the bluetooth driver and then put, but the battery is not correctly, telling me to switch to BT when I
  with FN + F8.
  He said I'm keep lack of ToshDpAPI.dll, even if I installed atheros before filter?

  Also, when I restart computer wifi get a second, and then said that there is no connection.
  When you switch the switch (FN + F8) market it works fine?

  Wierdest thing is I installed the same computer, that I bought for my brother and it works fine witout of problems?
  What should I do?

  Don't tell me to reinstall the wifi and BT drivers/stack, cause I did it several times and it's worked so far.

  I installed all the drivers are all downloaded from selection toshiba and 64-bit drivers.

  Many people have various problems after the installation of clean operating system. Problem is that all the drivers, tools and utilities must be installed in the proper installation order. Maybe you have installed your laptop a little different this laptop from your brother.

  Here is the order of the good setup for Win7 64 bit:

  Win7 SP1
  SW 9.2.0.1015 Chipset installation utility
  4.8.6.0 TOSHIBA supervisor password utility
  TOSHIBA HW Setup Utility 4.8.6.0
  Sun Java2 Runtime Environment 1.6.0_20
  TOSHIBA Bulletin Board V2.1.10
  TOSHIBA ReelTime 1.7.17.0
  Intel Management Engine Interface 7.0.2.1164
  Driver Intel 8.15.10.2353
  NVIDIA 8.17.12.6669 display driver
  Driver Intel Rapid Storage Technology 10.1.2.1004
  TOSHIBA value added package 1.5.4.64
  USB3.0 Driver 2.0.32.0
  NVIDIA HD Audio Driver 1.1.13.1
  Conexant Audio Driver 8.51.1.0a
  Intel Wireless LAN Driver 14.0.2.2.1.s64_wCAT
  or
  Atheros Wireless LAN Driver 9.2.0.206.0.s3264_wCAT
  or
  Driver Realtek Wireless LAN Driver 2.00.0013
  TOSHIBA 1.0.3 Wireless LAN indicator
  Synaptics Touch Pad Driver 15.2.11.1
  TOSHIBA Software Modem 2.2.97 (SM2297ALS05)
  Conexant 7.80.4.53 Modem driver
  TOSHIBA HDD Protection 2.2.1.12
  Atheros Bluetooth Driver Package v1.0.7 Filter
  Battery Bluetooth for Windows by Toshiba v8.00.04 (T)
  Atheros LAN Driver 1.0.0.46
  1.0.0.12 Realtek card reader
  TOSHIBA Sleep 1.4.2.7 utility
  Facial recognition TOSHIBA V3.1.8
  TOSHIBA eco Utility 1.2.25.64
  Intel Proset 14.0.2.0.1.s64_wCAT
  Intel Wireless Display 2.0.29T
  TOSHIBA HDD_SSD 3.1.64.7 attention
  TOSHIBA Service Station V2.1.52
  TOSHIBA PC Health Monitor 1.7.4.64
  ConfigFree 8.0.37
  TOSHIBA Web Camera Application V2.0.0.19
  TOSHIBA V4.00.4.54 VCR - HAS
  WinDVD BD for TOSHIBA 10.0.5.855 3D
  Corel Digital Studio for TOSHIBA 1.5.10.332
  TOSHIBA Disc Creator 2.1.0.6 for x 64
  TOSHIBA Network Device ID registry setting tool 3.0.32.4 - 14_wMSI
  TOSHIBA Media Controller 1.0.86.2
  TOSHIBA Media Controller plugin 1.0.6.1
  PatchFiles$ $2 PCIIDEREG - 1.2
  PatchFiles$ $3 TosVolRegulator_x64_1.1
  SWHelper for Toshiba manual V1

  If you can not find the download page of some of them on Toshiba must not be installed and it is included in the original recovery image only.

  Please check this list and maybe you should try to install the OS as a result of this order of installation.

  Good luck.

• Satellite A300D and overheating

  Someone with a problem of overheating of the Satellite A300D, if so, how to overcome this?

  Hello!

  A friend of mine has a Satellite A300D. A very good laptop and he is very satisfied. He never told me about problems and it works perfectly.

  Why not overheating A300D? Do you have this problem?
  If so, how does?
  Maybe you should clean the laptop with a jet of compressed air to blow the dust from the cooling fans.

  Good bye

• Conflict between Toshiba Bluetooth Stack and drawers of power on Tecra M5

  There seems to be a bug in TosBtShell.dll and hope this alert could get fixed in a future revision. Possibly it will save others the effort that it has cost me to track down the problem on my Tecra M5 new. I had to give up Toshiba Bluetooth Stack and now using XP SP2.

  When the Bluetooth Manager is running, TosBtShell.dll updates the element ' Bluetooth' beside ' send to ' in the context menu of files and folders. Unfortunately it is in conflict with the shell software improvement Power drawers http://www.dynamickarma.com/powerdrawers.htm that I defer to speed up access to my files on the computer. This software allows you to right click on a folder to view its contents in a list. Then you mouse to any folder in the list and give him also as a sublist - and so forth as deeply as you want until you reach the folder or file you want. Right click on an item in the waterfall and you get a list of useful options. However, if the Bluetooth Manager is running when you do the right click, power drawers breaks down and you must close and re-open explorer.exe to recover.

  The conflict stops if you remove "to Bluetooth" in the context menu of files and folders. I proved this by using ShellExView from Nirsoft http://www.nirsoft.net/utils/shexview.html to disable the registry key "Bluetooth File extension" [sic]. This key is associated with the C:\WINDOWS\system32\TosBtShell.dll and the CLSID {6BEF3D0B-53F0-4b0d-B91C-C19ED3D4C9D1}. Unfortunately the registry key back again every time that you restart the Bluetooth Manager.

  David Tong.

  Hello

  Thanks for the information.
  However, on the Toshiba Bluetooth page you can always notice whether or not the new version of the driver BT is available.
  http://APS.toshiba-tro.de/Bluetooth/

  I recommend you to visit this site regularly

• Video problems and a green screen

  Hello

  I read the questions and answers on this topic, but some things work and others do not.  For example, I was able to solve one of my problems with some other fixes I found through online forums General for the 'green' screen that plays with the audio only.  It seems to work for me on you tube but not on Facebook more videos alhtough Facebook worked the first time when I rebooted.

  What I did get into my internet options and under accelerated graphics that I checked use software rendering instead of...

  and on the Security tab, I checked activate 64-bit processes in increased protected...  It Enhanced protected mode should as well then?  Should I check this option.

  I also treid to do what the responses recommended... as a right click on the video on Facebook when he plays and then I get a pop up I get the settings options or global settings and adobe flash player info... by clicking on settings gives me options but none for "screen", only for my microphone, camera and storage.  If I click on global settings, need me to flash player help.  And the last option, I get my version of Adobe info, which is version 13.00.214.  So no option to uncheck the box disable accelerated graphics cause I think I already did this in Control Panel.

  But why is working with youtube and videos from Facebook that I also tried to play videos as wmv and other video files files in my windows media player flash and then I get a screen black but still audio not play now.

  My computer is a HP Pavilion Notebook PC and it came with Windows already installed 8.1.  My graphics card is a Radeon R5 AMD graphics card.

  So what the devil now.  Should I install more recent Adode Player?  Even by unchecking the option graphis accelerated, this isn't really a solution for the deeper problem and the question, because then it slows down your graphics card?

  My computer is not even a week and I hate having to always download the patches and constant updates and spend hours searching for and trying to solve a problem that really should not appear in a first time.  Why are there so many problems with Windows?  Is this a problem with windows updates as well.  Active X controls?  Isuses of compatibility with 64-bit processes.  Can I use Firefox.  I did with my old HP, which finally launched the bucket and that's why I had to buy a new one.  I had to replace my battery before a year and my warranty battery lasted that long either and then the thing finally overheated and died.  But I had a lot of similar things happen before with the last HP laptop if it's Windows or is it HP or is it browsers, readers?

  I'm sorry if I'm unloading on you... I want too much, but it's so frustrating as a consumer of always having to go through such things.  I use my laptop to work on his own account so please help!

  Thanks for letting me vent...  I'd appreciate your help, thank you.

  A frustrated customer

  Thank you for visiting the Forums HP's Support and welcome. I'm sorry you're having problems.  I looked into your problem with video problems.

  You have uninstalled Internet Explorer?

  Have you tried Google Chrome?

  It already includes Adobe® Flash® Player built-in. Google Chrome automatically updates when new versions of Flash Player are available. Adobe are on version 15. Here'sa place to update. It has a link to Google Chrome as well.

  Here is a link to common problems of Flashplayer.

  I would try a system restore because this could undo any change that could happen with an update from Microsoft. Sometimes they have not completed or installed on the laptop.

  Hope this helps you.

  Thank you.

• 2 8 black Bluetooth problem

  Hello

  I can't use 2 bluetooth devices at the same time. My keyboard and bluetooth mouse work fine separately, but as soon as I turn both the keyboard becomes frequently disconnected and it behaves strangely. The rest keyboard does not respond for a while and all of a sudden, press a key several times as "med."

  I reinstalled the software Microsoft Bluetooth Enumerator and Lenovo Bluetooth but the problem remains.

  This is a screenshot of the Windows event during the problem Viewer.

  
  

• Lenovo G560 Bluetooth problem

  Hello! I have a laptop Lenovo G560 with Windows 7 64 bit and I can't use my bluetooth device.

  I downloaded the drivers from consumersupport.lenovo.com, I instaled them, but the device does not work.

  Also, I downloaded the energy management tools and the shortcut key, but here, everything seems ok.

  In Device Manager, the bluetooth adapter and bluetooth enumerator appear to be installed corectly, but there are 5 elements called peripheral Bluetooth not installed (I can not update the driver in the list of the drivers installed on my machine, and another driver does not exist). Please see also the Manager of peripherals and Fn + F5, I can use any function menu Bluetooth of the tasksbar ('show bluetooth devices' returns nothing, 'add a device' can not find anything, 'open settings' does work not etc.).

  In conclusion, I don't know what the problem is, and I strongly need help.

  Also, I need a full sheet of the device bluetooth (for an app I want to develop). I searched the pages of technical support from Lenovo and Broadcom (the manufacturer of the bluetooth device) and I can't find anything in the details (only "commercial" specifications). Do you have any ideas where I can find this information?

  Thanks for your replies!

  P.S Sorry for my bad English

  I tried all those things. Does not.

  I had reinstalled the operating system and drivers. All the problems are now fixed.

  Thanks for your replies!

  Sincerely, Jimmy

• HP dv6 3230us: Bluetooth problem HP Pavilion dv6 3230us

  Hi all

  I'm having a problem with the BT to my HP laptop driver. I have just reinstalled my system, and although I tried to reinstall the driver of BT, at the end of installation, I get the error of "make sure that the BT module is on.

  What should do? I tried to install the bluetooth driver and I got this at the end:

  

  Thank you

  Ana

  Hi, Anna:

  According to the list of parts for your laptop, you try to install the wrong bluetooth driver.

  You need this driver for the bluetooth radio has your laptop...

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_81348_2

  You may also install this software in order to enable the bluetooth radio.

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=4095874&swItemId=ob_112799_2&swEnvOid=4059