Broadband Internet block through the NAC

Similar Questions

• RV 320 won't internet traffic through the SMC modems

  We have recently installed a RV320 to use primarily as a gateway for FTP traffic. The router is installed power 2 60/10 circuits of our Internet service provider who provided 2 edge of the MSC devices and which have Wifi capabilities and router. When connect on modems in factory default state the RV320 connects but does not take advantage of the double connections in terms of speed. When disable us the wifi modems and router running the RV 320 connects but do not traffic through to the modems.

  Since the two modems are identical, we get the same news IP and gateway of each. I would prefer not to have the modem in router mode. Is there a setting on the RV that will connect and pass internet traffic with modems in mode 'dumbed down '.

  Graham Saywell

  Wanted to sound and image

  Toronto

  Hi Graham,

  The best scenario is to have both SMC routers on bridge mode and configure both on RV320 WAN interface with (PPPE, static IP, DHCP... He expense of your WAN connection)

  Can you please share with us what kind of WAN connection you use in the SMC routers?

  -Ensure the RV320 you have the latest firmware 1.1.0.09, otherwise you can download it from this link:

  http://software.Cisco.com/download/release.html?mdfid=284005929&softwareid=282465789&release=1.1.0.09&relind=available&rellifecycle=&RelType=latest

  -On RV320 under the management of the system--> Dual WAN and check Load Balance

  -After that, you set up the RV320 with the same type of WAN connection as a router SMC and SMC router mode Bridge and in this case, you should see the two public IP on RV320 of audit system summary

  If you do these steps and still you can not the public IP address RV320 and the SMC router in Bridge mode, please share with us the configuration file RV320 and screenshots of two CMS about the WAN configuration

  If in the case the SMC router does not have the option of working in Bridge mode, in this case, you will need to have the local of the SCM with subnet different e.g. 192.168.1.1/24 and other a 192.168.2.1/24

  on RV320 you can leave the configuration in DHCP on both WAN Ondaaah (if you have the DHCP Server enable SMC router) or you can configure the static IP address on the two wan

  * Please answer question mark or note the fact other users can benefit from the TI *.

  Thank you

  Mehdi

• If I buy a monthly account of xfinity wifi (which allows internet access through the device unique registred) can I use apple TV connected to my TV to the stream of the device on my TV?

  using apple tv to stream xfinity wifi

  The Apple tv needs Internet - wifi or Ethernet. Access normally means places that they have agreements with wifi (i.e. from Starbucks, McDonald's etc.). But you will need a connection Internet for the Apple TV work from your home. Although some use the hotspot on their phone.  You need a speed of ISP at 8mbps for HD streaming on iTunes or netflix requires only 5 for HD (due to compression).

  short answer is that you must get xfinity as your ISP not only access hotspot...

• HP 350 G1 PC Notebook: Sharing internet (wired) through the wireless card problem

  shortly...
  I share my connection wired wireless throug... hotspot... help (my public wifi) program
  It works well after os install (win 10 or 7 and 8.1)... for one or two days
  just a week or more there is no Internet throug...

  in other words, all things work very well
  work of hotspot
  I find the network and connect perfectly
  but no internet 
  any help please

  You use a third-party anti-virus software to control your firewall?  If so, try disabling it temporarily.

  See if the internet connection returns.

  WyreNut

• Free devices in the NAC 4.1

  Hello friends,

  I m the virtual gateway layer2 mode configuration, I m bit confused regarding what would be the free features of layer2 virtual gateway mode.

  whenever any device in the vlan for authentication, it will pass through NAC server but if I moved the normal port access vlan in the switch of ' switchport mode access vlan "that the device is off flow from the NAC.

  My knowledge regardless of the mapping vlan is being done in the NAC between authentication and vlan access only those VLANs is affected rest are all out of the stream of ANC, they will go as normal traffic.

  Also all my switches vlan management so when I don't create the mapping for management vlan that they do not pass through the NAC. Am I wrong?

  Please suggest me what other devices should be exempted from the networks, for example: printers and what else?

  Estela,

  You are right, in most of your assumptions. The essential with the NAC is to follow the flow of traffic and make sure in the not authenticated state, the flow of traffic is always in the CASE. It follows that if a port is not in a local VIRTUAL alongside unreliable network, it would never be repercussions of the NAC. For your VLAN authenticated, we need to ensure that taxiway, they are allowed only through CBS. This simple design rule in mind, look at your VLAN again and you will get most of the answers you seek.

  HTH,

  Faisal

• INTERNET CONNECTION PROBLEM - laptop computer connects is the DNS through the modem to broadband gateway to resolve the address of Web site

  Regardless of the browser that I use on my VISTA laptop, navigation stops... which means the laptop connects is no longer the DNS through the modem to broadband gateway to resolve the address of the Web site.

  However internet is on and some applications that Act on the internet are connected and okay. for example: Skype

  Hello

  Try this process.

  WinSock and TCP/IP

  When parasites get installed on your computer, they might create hooks in the system computer activities related to the program "Junk" files  When you get rid of the 'Junk' hooks could remain in the system, in the absence of target files (they cleaned) problems are created in the network and Internet related activities.

  If after uninstalling the "Junk", the Internet connection does not work as it should, you will need to restart the operating system parts which get trashed by the process.

  WinSock and TCP/IP update.

  Type Cmd in the search text box.

  Press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type netsh winsock reset at the command prompt and press the Enter key.

  Do the same process to refresh the TCP/IP just replace the command typed with.

  netsh int reset

  And the sam to do this.

  ipconfig/flushdns

  Restart your computer.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• R7000 as router with the router for mobile broadband Internet

  Hey guys. First of all, my apologies for my somewhat inadequate English skills. Secondly, I am brand new to the community, so apologies in advance for any fault :-) Third stop, apologize for having a complete beginner :-D

  So, for the issue: I recently bought a router top mobile broadband 4G (4 G MBR) to my apartment, because of the gap of strength and speed signal very low quality of the cable to the ground on my Street (fiber is to come next year).

  But the router provided by my operator isn't on par with my router R7000 Nighthawk when he comes to reach wifi, wifi speed, number of outputs of LAN and power of the processor.

  So, I want to use my R7000 my router, the internet signal from the air to the 4G MBR, then by cable to the WAN of the R7000.
  In other words; I want to just 4G MBR to simply pass / transfer the internet signal to my nighthawk R7000 router so I can use the R7000 as my router, LAN and wifi.

  How can I set this up?

  Thanks for your help!

  Update: the MBR has been no help at all. As far as I could tell, there is no possibility to bridge or pass-through mode. The R7000, as she does the work. I just put it in AP mode, adjust all the wired connections DHCP/auto IP assign and everything works great.

• Cisco ASA5520 facing ISP with private IP address. How to get the IPSec VPN through the internet?

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

  Hello guys,.

  I have Cisco ASA5520 facing the ISP with private IP address. We don't have a router and how to get the IPSec VPN through the internet?

  The question statement not the interface pointing to ISP isn't IP address private and inside as well.

  Firewall configuration:

  Firewall outside interface Gi0 10.0.1.2 > ISP 10.0.1.1 with security-level 0

  Firewall inside the interface Ethernet0 192.168.1.1 > LAN switch 192.168.1.2 with security-level 100

  I have public IP block 199.9.9.1/28

  How can I use the public IP address to create the IPSec VPN tunnel between two sites across the internet?

  can I assign a public IP address on the Gig1 inside the interface with the security level of 100 and how to apply inside to carry on this interface?

  If I configure > firewall inside of the item in gi1 interface ip address 199.9.9.1/28 with security-level 100. How to make a safe lane VPN through this interface on the internet?

  I'm used to the public IP address allocation to the interface outside of the firewall and private inside the interface IP address.

  Please help with configuration examples and advise.

  Thank you

  Eric

  Unfortunately, you can only complete the VPN connection on the interface the VPN connection source, in your case the external interface.

  3 options:

  (1) connect a router in front of the ASA and assign your public ip address to the ASA outside interface.

  OR /.

  (2) If your ISP can perform static translation of 1 to 1, then you can always finish the VPN on the external interface and ask your provider what is the static ip address assigned to your ASA out of the IP (10.0.1.2) - this will launch the VPN of bidirectionally

  OR /.

  (3) If your ISP performs PAT (dynamic NAT), then you can only start the tunnel VPN on the side of the ASA and the other end of the tunnel must be configured to allow VPN LAN-to-LAN dynamics.

• Hub topology and talk: can I traffic Internet road to PC at a radius of the site through the tunnel and NAT outside in the world on the 5520 hub?

  I don't know if it can be made to work or not, or if it's a mutually excluded NAT configuration that is not possible, but I have a 5520 ASA to my site central office with a fiber of 20Mbps Internet streams and two remote offices with ASA 5505 devices connected via DSL or cable modem and have finally got from Site to Site "spoke" VPN upward tunnels and run with the ability to route traffic to through a 'hairpin turn' speak-to-Spoke on the Hub Site 5520.

  I have desktop PC at each remote site speaks A & B that need to communicate directly with them to support a small group of work-style of the software point of sale that is actually hosted on a remote site A PC.

  PC on two remote sites must also be able to communicate with a credit card processing by the public Internet service, and I wish have the ASA 5505 units in each block of remote office as all traffic directly NAT'ed from each respective out on the local LAN PC straight Internet above each site cable modem or DSL modem. I want to force these PCs need to NAT their Internet-destination back through the ASA 5520 traffic located at the Home Office, on the VPN tunnels. In other words, I want the cable modem and DSL connections to route traffic strictly VPN encrypted to the Home Office and also behave like routers NAT for the local PC it.

  I can kill the 5505 prevents NAT for PCS in remote offices simply removing the rule dynamic NAT factory default for 'everything', but then I can't understand how to get my 5520 central to perform NAT which required of the remote PCs to talk to their service of Internet credit card processor without breaking the configs "NAT-free" necessary for VPN traffic to spoke-to-spoke to work. If I'm trying to put an entry static or dynamic NAT for a remote desktop on my 5520 ASA central, it breaks the VPN tunnel so that PC specific.

  Is that what I want to accomplish even possible with the ASA?

  Hi Neal,

  Yes, it's quite possible! below is a loss of things you need to do:

  (1) make sure of course on both the 5505 s of the ASA, you send ALL traffic from the local network through the VPN.

  (2) as Andrew mentioned, have the 'same-security-traffic permit intra-interface' command on the ASA 5520.

  (3) you do not have to have a configured proxy server, but it is also a good solution. But to make it work without her, assuming that the ASA 5505 remote subnets 192.168.1.0/24 and 192.168.2.0/24, add the config lines below to the ASA 5520:

  NAT (outside) 1 192.168.1.0 255.255.255.0

  NAT (outside) 1 192.168.2.0 255.255.255.0

  Global 1 interface (outside)

  Please note that 1 id, and the interface can be replaced according to the configuration you already have in place in the ASA 5520.

  I don't know what kind of NAT exemptions are at the origin of the questions for you, but if you can put a sanitized one of your ASA 5505 and ASA 5520 config, I can make suggestions concerning the exact configuration.

  Let me know if it helps!

  Thank you and best regards,

  Assia

• Can not share the internet connection through Wifi

  Hi all

  I am connected to the internet using an external antenna connected via USB to my mac (WIRELESS n 801.11). I want to share this connection since my mac with other devices, i.e. my iPhone. I use the internet connection through system preferences--> sharing--> sharing internet--> connection on the part of wlan to computers via WIFI and give a name and a password for the wifi settings. When I start the connection icon wifi on the the high watch the arrow menu to the top, but it gives an IP address from 169 auto... etc etc and I can't any traffic to my iPhone.

  I tried to configure IPv4 to use DHCP with a manual (instead of automatic DHCP) address and IP I enter the IP address used in the WiFi, wifi says that it is connected to the name of the internet connection in the shared connection, I opened but once again no traffic to the iPhone. Also tried disabling the firewall, once again nothing.

  I run El Capitan 10.11.2.

  Clues?

  OS X El Capitan: share your Internet connection

• Setting up a local network private through the device that extracts public wifi internet

  I travel a lot in a RV I don't have a continuous Internet connection wherever I go, usually a public wifi some Camping I am for. I have several devices that I use, but I don't want that they are open to the public wifi network. I've had people send photos from their phone to my Xbox so that I use and I want to be more secure and control my devices.

  I have a knowledge of basic networking. I was able to use my laptop to connect to a public wifi and then share the connection through Windows on the LAN ethernet port. I then connect that to my old Netgear DGND3700v2 DSL model with its DHCP function disabled. It worked for several months now, and I am able to connect to the ports of my router modem and lan with my devices. But some games on the xbox does not work because I can't redirect ports or control static and other IP addresses. I think that there should be a much easier way to do it.

  I looked in my router Repeater functions, but I don't think that's the way I need to go. I have no access to the routers of the campsites configure them as bases. I need something that will pull simply bind an existing wifi and then deliver this private to my LAN connection.

  Thanks in advance for any advice.

  It worked perfectly. I bought a Netgear AC1200 and easily plugged into the local public wifi. I then wired to the LAN cable/Fiber gray on the Netgear router port and then reset the router ran smart installation thereon and he set up hands down with a new local network on a separate ip address range. Now all my devices independently connect to my router via wifi or LAN and use internet through the Extender without that person outside to get in and I don't have my laptop of aging on all the time to do so.

• Can I download windows 2008 server R2 64 bit Bill through the Internet.

  I bought the copy at retail of windows server 2008 R2 64-bit x. and I send out countries but Server 2008 Media Server is here in India. I want to install this product on this server what can I do. ? can I download the support from the operating system through the internet in its place. ?

  media is here and server in the other place and he wants intallation with in 2 days and I can send media can I download os across the net.

  Help me for this matter.

  No, you can't downloadit. You must purchase the appropriate version.

  Windows Server forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• How to download windows xp - sp1 or sp1a - not through the internet

  Help. need to download windows xp service pack 1 or 1, but not through the internet because it keeps failing at half way through the download online.

  To avoid confusion and duplication of effort, please post a follow-up later all replies to your thread of origin-online http://answers.microsoft.com/en-us/windows/forum/windows_xp-windows_install/have-xp-no-service-pack-trying-to-download-sp1-how/831e0dcc-6b42-4242-9f81-cbd156daf856

• can someone change my WZC and the setting of security through the internet?

  can someone change my WZC and the setting of security through the internet? I was watching a video on youtube when my stop comp. and restarted on its own. start and my security program was not able to start, had to uninstall and reinstall to turn back. He told me has encountered a problem and that you must close the program and the program would not close. It comes in a loop. Security found nothing. WZC to capture multiple signals, but now I can't pick up a. right extremist to the modem.

  It seems that if you picked up some malware.  What is the full error message on "antimalware executable?

  I would like to cancel the restoration ago 2 months... it's really too long to rely on system restore.  Too many things have been added in the meantime who is affected negatively by the restoration.

  It is very difficult to say anything from the limited information you provided, but I suggest starting by download, install, update and run a full scan with MalwareBytes Anti-Malware.

  In your answer, in addition to providing the full text of the error messages, provide all of the following:

  What version of Windows, including service pack, do you have?
  What antivirus application do you use?  Is up to date? Have you ever let her subscription lapse?
  What other antimalware applications do you have?
  What is the brand and model of your computer?
  What is the brand and model of your wireless router?

• When I try to use Media player 11 or try to use live food of internet radio, I get nothing. When I search through the settings, I met a screen that says "no audio device".

  Original title: ideas: insert an error code or give a brief description of what you're trying to accomplish or difficult. _

  When I try to use Media player 11 or try to use live food of internet radio, I get nothing.  When I search through the settings, I met a screen that say, 'no audio device '.  I tried to update my card sound and nothing.

  Your help will be greatly appreciated.  If so, ask me questions and I will answer.

  Gary kenny

  theflyingelk

  (Number removed for privacy)
  

  (Email removed for privacy)
  

  Hi gary kenny,.
  1. when the question is is produced?
  2. the issue of 'No audio' intervene on other applications as well?
  3. What is the brand and model of your computer?
   
  Follow the steps and check if they help.
   
  Step 1:
   
  If you have HP and Compaq Windows XP computers, you can follow the steps mentioned in the article.
   
  No Audio in Windows XP device
  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c01427349&cc=us&DLC=en&LC=en
   
  Step 2:
   
  Or, you can uninstall and reinstall the sound drivers.
   
  a. click on START
  b. click Control Panel.
   
  You should have a few icons to come.
  If you do not, you must make sure that you have enabled the classic view.
   
  Locate the control panel option, it will be on the left side.
  Once activated the classic view
   
  Follow the rest of my instructions.
   
  c. click Device Manager
  d. sounds > search for your sound card (if you are not sure that your sound card is, post options and I'll tell you that one.)
  e. Note description brand / model, double-click on it, go to the tab drivers, note the version.
  f. make a right click on it and UNINSTALL it and restart the computer it will rebuild the driver stack.
  g. go to the manufacturers website and find the latest driver for your card download. (You must know the name of the sound card, if you wrote down from the above info), when you find it download: SAVE IT DO NOT HIT RUN (save it on your desktop for easy access.
  h. open the file that you have saved and right-click on it and select RUN AS ADMINISTRATOR(Now install it.). REBOOT after each installation of driver.
   
  Step 3:
   
  Sound drivers often rollback, so check that the version you just installed is always there. If not, the driver to keep until it sticks, it really shouldn't take more than three times
  
  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]