burned by another router through vpn

Similar Questions

• Access another network through VPN

  Hello, currently we have an easy vpn server in one of our sites. Remote users can access the LAN (172.17.x.x) through the VPN.  Is it possible to access another network (192.168.2.x) via the same VPN connection?  Please see the network diagram.

  

  Kind regards

  Tony

  Hello Tony

  Thank you for the config and details

  I've done the configuration in the assumption that the new subnet to which the VPN users wants to access is 192.168.2.0/24 and is behind the router Dlink

  VPN SERVER
  ----------------

  NZEV extended IP access list
  permit ip 192.168.2.0 0.0.0.255 any

  access-list 120 deny ip 192.168.2.0 0.0.0.255 10.0.0.0 0.0.0.255
  access-list 120 deny ip 192.168.2.0 0.0.0.255 192.168.25.0 0.255.255.255

  access-list 121 allow ip 10.0.0.0 0.255.255.255 192.168.2.0 0.0.0.255
  access-list 122 allow ip 192.168.25.0 0.0.0.255 192.168.2.0 0.0.0.255

  IP route 192.168.2.0 255.255.255.0 172.17.0.6

  CISCO router
  ------------
  IP route 192.168.2.0 255.255.255.0 172.21.100.1
  IP route 10.0.0.0 255.0.0.0 172.17.0.71
  IP route 192.168.25.0 255.255.255.0 172.17.0.71

  Router DLink
  ---------------
  IP route 10.0.0.0 255.0.0.0 172.21.100.2
  IP route 192.168.25.0 255.255.255.0 172.21.100.2

  Please let me know if you have any other questions

  Harish.

  be sure to note all the useful messages!

• PIX: Dialin routing through a different VPN VPN

  Here's the scenario: I have 2 PIX firewall on various sites connected to the internet with public (PIX A and B PIX) IP addresses.

  There is a permanent VPN site to site between the two and there is a clear separation between subnets between the two sites (internal network behind PIX is 10.10.4.0/24 and the internal network behind PIX B 192.168.0.0/16).

  I created dialin VPDN access to PIX for laptops to dialin via VPN - it currently allows access to the subnet 10.10.4.0/24 without problem.

  Now - I need these users of portable computers, when connects via the VPN to PIX has to be able to access the other remote site and access the subnet 192.168.0.0/16 of routing through the VPN site to site of PIX B.

  Is this possible? I would be grateful to anyone who helps with that. Thank you...

  This is currently not possible on the PIX as the PIX will not route traffic back on the same interface, it is entered in the.

  This feature will be available in the upcoming v7.0 version, which is currently in beta, so look out for it and you're ready to go.

• Connect to Airport Extreme to another router

  Hello.  I searched this forum to see if my question is already answered.  I couldn't find all the signs that answer.  If it has already been answered, please point me to the subject.  Otherwise, here's my question:

  I need to expand Internet coverage in my house.  This is the configuration I want to implement:

  • Cable modem (at one end of my house) connected to a WiFi router non - Apple.

  • Use an Ethernet cable to the router through my attic, at one Airport Extreme to the other end of the House

  • I would like to run an Ethernet cable from the Airport Extreme to my TV and another cable to an AppleTV

  This would give wireless coverage to the entire House and Internet wired for television and the AppleTV.

  I would like some advice on how best to implement.  Here are a few questions (although I don't know if I ask to everything that I need to ask):

  • If the Airport Extreme be configured with DHCP or a static IP address?

  • If the Airport Extreme and the other router have the same SSID and password?  Or it doesn't matter?

  • What should I do a configuration to make the Ethernet connection work seamlessly in Airport Extreme to the other router on the cable modem?

  • I guess I can configure the other router (connected to the cable modem) to DHCP.  Is this correct?

  Thanks in advance for any advice.  If all goes well, I plan to spend this Saturday morning crawling into the attic and tonight Saturday benefiting the whole Internet.

  Should the Airport Extreme be configured with DHCP or a static IP address?

  DHCP, unless you have a preference for a static IP address.

  Airport Extreme and the other router has the same SSID and password?

  Yes, if you want both of your routers to behave as if they provided a unique network of "big". No, if you want to require users to log on the wireless provided separately by each router.

  I have to do any configuration to make the Ethernet connection work seamlessly in Airport Extreme to the other router on the cable modem?

  Just run configuration 'Wizard' of Apple, and it will assign the correct parameters to the AirPort Extreme.

  I guess I can configure the other router (connected to the cable modem) to DHCP.  Is this correct?

  It is not clear, given that we do not know what another router you may have. Do you mean that the other router connected to the modem via DHCP... or... you hear the other router provide DHCP and NAT services for the entire network?

• Cannot access my router through the Explorer configuration page

  I need to do a port forwarding on my router. My internet connection works (even if she falls occasionally) and I can also connect to other computers on my network. However, I cannot access my router through IE page (I get a message saying: page not found). When I go see the map in the options Vista network, the router is not displayed and when I clikc on "See the whole map", I get a message saying that Windows cannot detect any computer or devices.

  My connection to the router is connected, and it is a WRT54G Lyinksys. Any ideas how I can see my router or go to its page layout? Another thing, I went to CMD and the ping command returns a default gateway 192.168.1.1, which is what I have my using the address of the webb page.

  Thanks for any help.

  Hi JBHPUser,
  
  (a) other router configuration page, you are able to access other Web sites?
   
  (b) what operating system and Internet Explorer version do you use?
   
  This article can be very useful.
   
  You receive an error message in Internet Explorer: "Internet Explorer cannot display the webpage".
  http://support.Microsoft.com/kb/956196
   
  You can also access these links, which is primarily for Windows Vista, but are also applies to Windows 7
   
  
  Solve problems with computers not appearing is not in the network map
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-computers-not-appearing-on-the-network-map
   
  Network connection problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems
   
   
  
  Aziz Nadeem - Microsoft Support

• Two RV016, gateway to gateway, routing over VPN

  Hello

  I have two RV016, I have a vpn connection from gateway to gateway between the two and I can ping computers on both sides, but I can't reach the third lan (10.0.0.0/255.0.0.0). I can join this network to routerA but not of routerB.

  My Network typology:

  

  Configuration of routers (see attachments)

  How can I configure static routes on router B?

  I tried to do, but it does not work (see RouterB_routing.jpg)

  Can someone help me?

  Thank you.

  Krzysztof,

  
  

  Unfortunately the rv016 you cannot make static through the vpn tunnel routes as it isn't an ipsec interface in the static routes section of the router.  This is normal, the router will recognize that the default setting of lan in the vpn tunnel.

  
  

  You need to business routers to make the static routes through the ipsec tunnel.

• Traffic of Client VPN routing via VPN Site to Site

  Hello

  We have the following scenario:

  • Office (192.168.2.x)
  • Data Center (212.64.x.x)
  • Home workers (192.168.2.x) (scope DHCP is in the office subnet)

  Connections:

  • Desktop to Data Center traffic is routed through a Site at IPSec VPN, which works very well.
  • Welcome to the office is routed through a Site IPSec VPN Client.

  The question we have right now, is the Client VPN works, and we have implemented a split tunnel which includes only the subnet of the Office for a list of network.

  What I have to do, is to route all traffic to home' to 'Data Center' by site to Site VPN is configured.

  I tried to add the ranges of IP data center to the list of Client VPN Split tunnel, but when I do that and try to connect at home, I just get a "connection timed out" or denied, as if she was protected by a firewall?

  Could you please let me know what I missed?

  Result of the command: "show running-config"
  : Saved
  :
  ASA Version 8.2(5)
  !
  hostname ciscoasa
  domain-name skiddle.internal
  enable password xxx encrypted
  passwd xxx encrypted
  names
  name 188.39.51.101 dev.skiddle.com description Dev External
  name 192.168.2.201 dev.skiddle.internal description Internal Dev server
  name 164.177.128.202 www-1.skiddle.com description Skiddle web server
  name 192.168.2.200 Newserver
  name 217.150.106.82 Holly
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  shutdown
  !
  interface Ethernet0/4
  shutdown
  !
  interface Ethernet0/5
  shutdown
  !
  interface Ethernet0/6
  shutdown
  !
  interface Ethernet0/7
  shutdown
  !
  interface Vlan1
  nameif inside
  security-level 100
  ip address 192.168.2.254 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  ip address 192.168.3.250 255.255.255.0
  !
  !
  time-range Workingtime
  periodic weekdays 9:00 to 18:00
  !
  ftp mode passive
  clock timezone GMT/BST 0
  clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00
  dns domain-lookup inside
  dns server-group DefaultDNS
  name-server Newserver
  domain-name skiddle.internal
  same-security-traffic permit inter-interface
  object-group service Mysql tcp
  port-object eq 3306
  object-group protocol TCPUDP
  protocol-object udp
  protocol-object tcp
  object-group network rackspace-public-ips
  description Rackspace Public IPs
  network-object 164.177.132.16 255.255.255.252
  network-object 164.177.132.72 255.255.255.252
  network-object 212.64.147.184 255.255.255.248
  network-object 164.177.128.200 255.255.255.252
  object-group network Cuervo
  description Test access for cuervo
  network-object host Holly
  object-group service DM_INLINE_TCP_1 tcp
  port-object eq www
  port-object eq https
  object-group service DM_INLINE_TCP_2 tcp
  port-object eq www
  port-object eq https
  object-group service DM_INLINE_TCP_3 tcp
  port-object eq www
  port-object eq https
  object-group service DM_INLINE_TCP_4 tcp
  port-object eq www
  port-object eq https
  access-list inside_access_in extended permit ip any any
  access-list outside_access_in remark ENABLES Watermark Wifi ACCESS TO DEV SERVER!
  access-list outside_access_in extended permit tcp 188.39.51.0 255.255.255.0 interface outside object-group DM_INLINE_TCP_4 time-range Workingtime
  access-list outside_access_in remark ENABLES OUTSDIE ACCESS TO DEV SERVER!
  access-list outside_access_in extended permit tcp any interface outside object-group DM_INLINE_TCP_3
  access-list outside_access_in remark Public Skiddle Network > Dev server
  access-list outside_access_in extended permit tcp 192.168.3.0 255.255.255.0 interface outside eq www
  access-list outside_access_in extended permit tcp object-group rackspace-public-ips interface outside eq ssh
  access-list outside_access_in remark OUTSIDE ACCESS TO DEV SERVER
  access-list outside_access_in extended permit tcp object-group Cuervo interface outside object-group DM_INLINE_TCP_1 inactive
  access-list outside_access_in extended permit tcp 192.168.3.0 255.255.255.0 host dev.skiddle.internal object-group DM_INLINE_TCP_2 inactive
  access-list inside_access_in_1 remark HTTP OUT
  access-list inside_access_in_1 extended permit tcp any any eq www
  access-list inside_access_in_1 remark HTTPS OUT
  access-list inside_access_in_1 extended permit tcp any any eq https
  access-list inside_access_in_1 remark SSH OUT
  access-list inside_access_in_1 extended permit tcp any any eq ssh
  access-list inside_access_in_1 remark MYSQL OUT
  access-list inside_access_in_1 extended permit tcp any host 164.177.128.200 object-group Mysql
  access-list inside_access_in_1 remark SPHINX OUT
  access-list inside_access_in_1 extended permit tcp any host 164.177.128.200 eq 3312
  access-list inside_access_in_1 remark DNS OUT
  access-list inside_access_in_1 extended permit object-group TCPUDP host Newserver any eq domain
  access-list inside_access_in_1 remark PING OUT
  access-list inside_access_in_1 extended permit icmp any any
  access-list inside_access_in_1 remark Draytek Admin
  access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 4433
  access-list inside_access_in_1 remark Phone System
  access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 35300 log disable
  access-list inside_access_in_1 remark IPSEC VPN OUT
  access-list inside_access_in_1 extended permit udp any host 94.236.41.227 eq 4500
  access-list inside_access_in_1 remark IPSEC VPN OUT
  access-list inside_access_in_1 extended permit udp any host 94.236.41.227 eq isakmp
  access-list inside_access_in_1 remark Office to Rackspace OUT
  access-list inside_access_in_1 extended permit ip 192.168.2.0 255.255.255.0 object-group rackspace-public-ips
  access-list inside_access_in_1 remark IMAP OUT
  access-list inside_access_in_1 extended permit tcp any any eq imap4
  access-list inside_access_in_1 remark FTP OUT
  access-list inside_access_in_1 extended permit tcp any any eq ftp
  access-list inside_access_in_1 remark FTP DATA out
  access-list inside_access_in_1 extended permit tcp any any eq ftp-data
  access-list inside_access_in_1 remark SMTP Out
  access-list inside_access_in_1 extended permit tcp any any eq smtp
  access-list outside_1_cryptomap extended permit ip 192.168.2.0 255.255.255.0 object-group rackspace-public-ips
  access-list inside_nat0_outbound extended permit ip 192.168.2.0 255.255.255.0 192.168.100.0 255.255.255.0
  access-list inside_nat0_outbound extended permit ip 192.168.2.0 255.255.255.0 object-group rackspace-public-ips
  access-list inside_nat0_outbound extended permit ip any 192.168.2.128 255.255.255.224
  access-list inside_1_cryptomap extended permit ip 192.168.2.0 255.255.255.0 object-group rackspace-public-ips
  access-list outside_1_cryptomap_1 extended permit tcp 192.168.2.0 255.255.255.0 object-group rackspace-public-ips eq ssh
  access-list RACKSPACE-cryptomap_1 extended permit ip 192.168.2.0 255.255.255.0 object-group rackspace-public-ips
  access-list RACKSPACE-TEST extended permit ip host 94.236.41.227 any
  access-list RACKSPACE-TEST extended permit ip any host 94.236.41.227
  access-list InternalForClientVPNSplitTunnel remark Inside for VPN
  access-list InternalForClientVPNSplitTunnel standard permit 192.168.2.0 255.255.255.0
  access-list InternalForClientVPNSplitTunnel remark Rackspace
  access-list InternalForClientVPNSplitTunnel standard permit 164.177.128.200 255.255.255.252
  access-list InternalForClientVPNSplitTunnel remark Rackspace
  access-list InternalForClientVPNSplitTunnel standard permit 164.177.132.16 255.255.255.252
  access-list InternalForClientVPNSplitTunnel remark Rackspace
  access-list InternalForClientVPNSplitTunnel standard permit 164.177.132.72 255.255.255.252
  access-list InternalForClientVPNSplitTunnel remark Rackspace
  access-list InternalForClientVPNSplitTunnel standard permit 212.64.147.184 255.255.255.248
  pager lines 24
  logging enable
  logging console debugging
  logging monitor debugging
  logging buffered debugging
  logging trap debugging
  logging asdm warnings
  logging from-address [email protected]/* */
  logging recipient-address [email protected]/* */ level errors
  mtu inside 1500
  mtu outside 1500
  ip local pool CiscoVPNDHCPPool 192.168.2.130-192.168.2.149 mask 255.255.255.0
  ip verify reverse-path interface inside
  ip verify reverse-path interface outside
  ipv6 access-list inside_access_ipv6_in permit tcp any any eq www
  ipv6 access-list inside_access_ipv6_in permit tcp any any eq https
  ipv6 access-list inside_access_ipv6_in permit tcp any any eq ssh
  ipv6 access-list inside_access_ipv6_in permit icmp6 any any
  icmp unreachable rate-limit 1 burst-size 1
  icmp permit any outside
  no asdm history enable
  arp timeout 14400
  global (outside) 1 interface
  nat (inside) 0 access-list inside_nat0_outbound
  nat (inside) 1 0.0.0.0 0.0.0.0
  static (inside,outside) tcp interface www dev.skiddle.internal www netmask 255.255.255.255
  static (inside,outside) tcp interface ssh dev.skiddle.internal ssh netmask 255.255.255.255
  access-group inside_access_in in interface inside control-plane
  access-group inside_access_in_1 in interface inside
  access-group inside_access_ipv6_in in interface inside
  access-group outside_access_in in interface outside
  route outside 0.0.0.0 0.0.0.0 192.168.3.254 10
  timeout xlate 3:00:00
  timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
  timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
  timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  timeout floating-conn 0:00:00
  dynamic-access-policy-record DfltAccessPolicy
  aaa authentication telnet console LOCAL
  aaa authentication enable console LOCAL
  http server enable 4433
  http 192.168.1.0 255.255.255.0 inside
  http 192.168.2.0 255.255.255.0 inside
  no snmp-server location
  no snmp-server contact
  snmp-server enable traps snmp authentication linkup linkdown coldstart
  crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
  crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
  crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
  crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
  crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
  crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
  crypto ipsec security-association lifetime seconds 86400
  crypto ipsec security-association lifetime kilobytes 4608000
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set security-association lifetime seconds 28800
  crypto map outside_map 1 match address RACKSPACE-cryptomap_1
  crypto map outside_map 1 set pfs
  crypto map outside_map 1 set peer 94.236.41.227
  crypto map outside_map 1 set transform-set ESP-AES-128-SHA
  crypto map outside_map 1 set security-association lifetime seconds 86400
  crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
  crypto map outside_map interface outside
  crypto ca trustpoint _SmartCallHome_ServerCA
  crl configure
  crypto ca certificate chain _SmartCallHome_ServerCA
  certificate ca xxx
  quit
  crypto isakmp enable outside
  crypto isakmp policy 10
  authentication crack
  encryption aes-256
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 20
  authentication rsa-sig
  encryption aes-256
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 30
  authentication pre-share
  encryption aes-256
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 40
  authentication crack
  encryption aes-192
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 50
  authentication rsa-sig
  encryption aes-192
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 60
  authentication pre-share
  encryption aes-192
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 70
  authentication crack
  encryption aes
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 80
  authentication rsa-sig
  encryption aes
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 90
  authentication pre-share
  encryption aes
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 100
  authentication crack
  encryption 3des
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 110
  authentication rsa-sig
  encryption 3des
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 120
  authentication pre-share
  encryption 3des
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 130
  authentication crack
  encryption des
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 140
  authentication rsa-sig
  encryption des
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 150
  authentication pre-share
  encryption des
  hash sha
  group 2
  lifetime 86400
  telnet 192.168.1.0 255.255.255.0 inside
  telnet 192.168.2.0 255.255.255.0 inside
  telnet timeout 5
  ssh timeout 5
  console timeout 0
  dhcpd auto_config outside
  !
  dhcprelay server 192.68.2.200 inside
  threat-detection basic-threat
  threat-detection scanning-threat
  threat-detection statistics host
  threat-detection statistics access-list
  threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
  ntp server 194.35.252.7 source outside prefer
  webvpn
  port 444
  svc image disk0:/anyconnect-macosx-i386-2.4.1012-k9.pkg 1 regex "Intel Mac OS X"
  group-policy DfltGrpPolicy attributes
  vpn-tunnel-protocol IPSec webvpn
  group-policy skiddlevpn internal
  group-policy skiddlevpn attributes
  dns-server value 192.168.2.200
  vpn-tunnel-protocol IPSec l2tp-ipsec
  split-tunnel-policy tunnelspecified
  split-tunnel-network-list value InternalForClientVPNSplitTunnel
  default-domain value skiddle.internal
  username bensebborn password *** encrypted privilege 0
  username bensebborn attributes
  vpn-group-policy skiddlevpn
  username benseb password gXdOhaMts7w/KavS encrypted privilege 15
  tunnel-group 94.236.41.227 type ipsec-l2l
  tunnel-group 94.236.41.227 ipsec-attributes
  pre-shared-key *****
  tunnel-group skiddlevpn type remote-access
  tunnel-group skiddlevpn general-attributes
  address-pool CiscoVPNDHCPPool
  default-group-policy skiddlevpn
  tunnel-group skiddlevpn ipsec-attributes
  pre-shared-key *****
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  policy-map type inspect dns preset_dns_map
  parameters
  message-length maximum client auto
  message-length maximum 512
  policy-map global_policy
  class inspection_default
  inspect dns preset_dns_map
  inspect ftp
  inspect h323 h225
  inspect h323 ras
  inspect rsh
  inspect rtsp
  inspect esmtp
  inspect sqlnet
  inspect skinny
  inspect sunrpc
  inspect xdmcp
  inspect sip
  inspect netbios
  inspect tftp
  inspect ip-options
  policy-map global-policy
  class inspection_default
  inspect icmp
  inspect icmp error
  inspect ipsec-pass-thru
  inspect ftp
  !
  service-policy global_policy global
  smtp-server 164.177.128.203
  prompt hostname context
  call-home reporting anonymous
  Cryptochecksum:6c2eb43fa1150f9a5bb178c716d8fe2b
  : end
  

  You must even-Security-enabled traffic intra-interface to allow communication between vpn VPN.

  With respect,

  Safwan

  Remember messages useful rate.

• broadcast another program through labview

  Hello

  I have a question

  is it possible to broadcast another program through LabVIEW?

  for example, I run a program in my computer, is it possible to have the remote people to look at how the program runs through the Internet and LabVIEW?

  Thank you

  Cynitha

  Yes and no.

  Yes - if you are showing them how to use a VI that you configured as a server, they can watch using remote façade. There are also (limited) ActiveX controls that allow you to use external applications in LabVIEW, IE: Word, Excel, WMP, etc.

  No - if there is no involved VI, you want to just show them a random program, you can simply use Remote Desktop connection. Click Start > programs > Accessories > Remote Desktop Connection, its fairly explicit use.

• Connect to another computer via VPN

  How to connect to another modem with VPN network. The other computer is connected directly to the modem.

  Hello

  Maybe this can help.

  http://www.windowsecurity.com/articles/configure-VPN-connection-Windows-XP.html

  http://support.Microsoft.com/kb/314076

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Cascading Linksys router to another router (LAN LAN)

  My current set is the asame LAN - LAN as in this link... http://KB.Linksys.com/Linksys/GetArticle.aspx?docid=785463d9ecaf4cac84aed245b08d615f_3733.XML

  my 'main' router is defined as DHCP server only, and wireless is disabled on it. This router is in the basement.

  my "secondary" router is in the living room... The DHCP service is disabled on this router and this provided routers beams for the House at 2.4 and 5 Ghz wireless... allows to call "Network 2" SSID 2,4 and 5 what we call "Netowrk 5".  Wireless coverage is really good in the whole of the House except basement. I would like to do better in the basement as well.

  In this current set up what could I do to make it better. As the "primary" router isn't beaming wireless I might add another router 'third '?

  Any help would be appreciated.

  Thank you

  He should choose the height of the 2.4 GHz SSID or the SSID 5 GHz, but only in the case were two router have the same SSID for the 2.4 Ghz and the same SSID for 5 Ghz. (Remember separated SSID at 2.4 Ghz and 5 Ghz signals)

  It can be confusing, so here's an example:

  Main router:

  2.4 Ghz SSID: myhouse

  5 GHz SSID: myhouse_5gz

  Linksys router:

  2.4 Ghz SSID: myhouse

  5 GHz SSID: myhouse_5gz

  When a wireless client moves around the place he will switch to signal the harder for SSID it finally connected to.

• Problems with my 4 port Gigabit Security Router with VPN

  OK, I got a wireless router and I have a Web site hosted by 1and1.com and I could connect my fine site. But recently I got the 4 port Gigabit Security Router with VPN and since then I have not been able to connect to it even, I started my own ftp server it always blocks and it will capture everything until she tries to recover the files, then it expires just after a while

  What is the model number of your device? If you have a Web server and an FTP server behind the router, you will need to transfer the ports used by the said request. Ports TCP 80 and TCP 21.

• I can mutually ping in router RVS4000 VLAN without another router

  One of our clients has RVS400 router with 4-port LAN VIRTUAL. We have recently added Crestron devices to our network and have some network problem. Search Google points to this page: Network slow question as discessed in this article: Troubleshooting network slow issues... There are two things happening with the Crestron system:... www.chicagotech.net/NetForums/viewtopic.php?f=1&t=7737 It recommends to create a local network VIRTUAL for Crestron. However, the Cisco RVS400 manual States: "function VLANS at layer 2.» VLANS isolate traffic within the VIRTUAL LAN, router layer 3 functioning router is needed to allow traffic between the VLANS. Layer 3 routers identify segments and coordinate with local networks virtual. "If we create two VLANS on the router without another router, can access us each other in these two VLAN?

  Hi chicagotech.

  I implemented a RVS4000 in our laboratory and created 2 VLAN, VLAN 1 and VLAN 2. I connected two PCs, 1 on each VLAN and they were able to ping each other with Inter-VLAN routing active. Here are the steps I followed:

  1. Go to L2 Switch-> create a VLAN. I have added VLAN ID: 2 and click Add VLAN
  2. Go to membership to a VLAN and select VLAN 2 from the drop-down. In the table for Port 2, select the Untagged radio button and click on save at the bottom.
  3. Go to settings-> Advanced Routing and ensure that the Inter-VLAN routing is enabled. (It is enabled by default)
  4. Connect a PC to port 2 and make sure he gets an IP to VLAN 2. (in this case 192.168.2.100) Ping this address in VLAN 1 PC-> success. From VLAN 2 PC, ping 192.168.1.101 (VLAN 1 PC)-> success.
  5. As a test I gave then the PCs in each VLAN to an IP address static and turned off the DHCP server on the router. 192.168.1.102 was able to ping 192.168.2.102 and vice versa.
  6. I then disabled Inter-VLAN routing and the PC could ping is no longer among them. They still had full access to the internet.

  It seems that the devices connected to the RVS4000 in different VLANS have no trouble to access each other with Inter-VLAN routing active.

• AAA authentication for external router through PIX 515

  I have been in vain, to get the authentication AAA works to my external router, through the PIX.

  When I connect the router directly within that network (bypassing the PIX) AAA works fine, so I know the configuration of the AAA works between the router and the ACS server.

  Initially, I got the PIX configured with a static map between a global external address 192.x.x.12 and a 10.200.1.187 for the ACS server local address, but that didn't work either. So, currently I am using NAT exemption for the ACS server, but it does not work either.

  If I activate the debug on the PIX package, I see the ACS authentication request and response between the router and GBA when I try to connect to the router, but it is not successful. After the three way TCP handshake, the router repeats it is last receipt, and then the ACS asked an RST.

  The attached diagram shows the simple connection that I'm trying to create.

  The configuration of the PIX is also attached. (too large messages size):

  Thanks in advance for your help. I tried EAC for two days and have not found solutions that look like this.

  Ron Buchalski

  What to do is:

  1 PIX:

  -static map the ACS/GANYMEDE to a public IP address

  static (inside, outside) x.x.x.10 10.1.1.25 netmask 255.255.255.255

  -otherwise, if you have enough public IP, use the port forwarding for card IP ACS to PIX outside IP of the interface, IE x.x.x.2, via a specific TCP 49:

  public static tcp (indoor, outdoor) interface 49 10.1.1.25 49 netmask 255.255.255.255

  * allow ACS talk to external router via public IP

  Create/add entry for ACL applied to the outside interface to allow the GANYMEDE Protocol + switch router external to the ACS:

  access outside permit tcp host XXX1 host x.x.x.10 eq 49 list (Ganymede + use tcp 49)

  outside access-group in external interface

  * x.x.x.1 = outside the router

  2 ACS

  -Add the outside router IP (FastEthernet face PIX outside interface) interface as a client of the AAA

  -Making of course secret key is identical at ACS and router

  3. the outside router

  -Add the ACS as radius-server using its IP public, as mapped in PIX which is x.x.x.10.

  -check the key AAA statement is accurate.

  The test without saving the config is outside the router. Save ok once confirmed.

  I have similar facility before, and it worked very well.

  Pls note all useful message (s)

  AK

• router through comcast. When my laptop detects all networks, they are all together to connect automatically. It is causing me launch my own network. ?

  I have a router through comcast. When my laptop detects all networks, they are all together to connect automatically. It is causing me launch my own network. When I try to uncheck the other networks they remain just verified. I m not sure how to fix it

  You may contact Comcast or the manufacturer of your router support wireless.

• Is it possible to reassign the temp folder to burn to another drive?

  Is it possible to reassign the temp folder to burn to another drive?

  Change the default save location,

  http://Windows.Microsoft.com/en-us/Windows7/customize-a-library