buttons (F1, F2) lighting control doesn't work after driver update chart 10 bootcamp windows

Similar Questions

• Windows Vista: The keys to open the mail or the Internet doesn't work after driver update

  Updated driver and since smart keyboard of opening of mail, windows, research, etc., do not work.  They worked perfectly fine before this update.  Is there a way I can make them work again please?

  Hello

  You don't say where you got the update of.

  See if that helps you.

  Do a system restore, if necessary using the safe, before the problem started.

  http://bertk.MVPs.org/html/restoresysv.html

  How to access Safe Mode

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  See you soon.

• Pavilion dv7-4270us: dv7-4270us bluetooth does not work after driver update

  I recently updated my drivers from the HP website.  Now, I know it was a mistake that bluetooth has not been installed correctly.    And there is no option "driver restore.  I tried several times sp50180, according to the HP website and also tried the old version listed (sp49153).   They old version did not install correctly and a new seemed especially, but none of my Bluetooth devices that used to work to do now.   I can 'connect to' some devices but they cannot transfer photos, connect to the audio, etc.  Some devices that are used to work can still be seen when I say "add a bluetooth device".  After installation, in the Device Manager, I find the following:

  The radio Bluetooth: Bluetooth Broadcom 2070 and Microsoft Bluetooth Enumerator (both working properly)

  Human Interface Device: Bluetooth Remote Control (works)

  Modem: Modem Standard via a Bluetooth #2 link (works)

  Network cards (all working correctly):

  Device Bluetooth (personal area network)

  (Heading RFCOMM Protocol TDI) Bluetooth device

  (and my other network devices, all functioning properly also)

  Other devices: this is the problem area.  After installation and reboot, I always find myself with 10 entries "Bluetooth Peripheral Device", all with a yellow exclaimation mark and all say real estate "Other devices", "unknown" (GSM) and the location is "on Microsft Bluetooth enumerator". "."

  I tried right click and uninstall it, but when I reboot they come back to the top, search windows update, but can not find a driver and go straight to the "other devices".  I also tried to uninstall the "Broadcom 2070 Bluetooth 3.0" 'Programs and features' and right-click to delete each listed above bluetooth driver and then run the sp50180 again and it will install without error and find the same above drivers that work and leave the same 10 does not.  And my Bluetooth headphones (two different ones) is more work (or can be seen) and my Bluetooth phone can be 'connected' but any attempt to transfer fails.

  I've exhausted all ideas on the web, I could find, and none have helped.  I tried to load a restore point, but after having so many pilot facilities, there is no point of restoration with the appropriate driver.  A full backup of the system on another drive, but much changed the applications and data files so I cannot restore it.  Unless someone knows how to use a full backup of the Windows 7 system to restore only the Bluetooth driver.

  Another idea is that the driver update that messed up things maybe changed some other file or a registry setting that is not corrected by sp50180, but that seems unlikely.

  Is it possible to manually install each of the 10 'other devices' drivers?  If I right click on a defective device and select "update driver software" no matter if I select the drive C:\ or F:\ (my driver and software download drive) or automatic search (including online) - it does not find the driver files.  I also tried to select properties and 'put to day driver' but the same results.

  Any help would be greatly appreciated.

  I found a solution. I received a call of support in Mumbai.  HP gave me a free call because they were not able to set a guarantee repair questions, so gave me the free support call.  I took an hour, but ended up the solution was very simple.

  There were these problems:

  1) 10 'other devices' in device with the exclamation points Manager can be uninstalled, but still were automatically reinstalled with the same exclamation point.  No pilot was available to the public for them.

  (2) my phone under Bluetooth devices could connect but would not photos transfer.

  (3) neither my helmet Bluetooth would not work.

  The solution was simply to go to 'Show Bluetooth devices' and right-click on each and select 'Delete device' (even if dimmed they might still be revoked).  After all have been abducted there were no "other devices" in Device Manager.  I then added each Bluetooth device again.  This was very well all work.  I also noticed my phone was five drivers "Bluetooth Device" was so 5 of the 10 exclamation points himself.

  For some reason, deletion of the driver in the Device Manager has not deleted the list "Bluetooth Device".  And by uninstalling and reinstalling the drivers, it does not work.

  If the answer is simple.  Before removing the drivers Bluetooth first remove all Bluetooth devices.

• Satellite A100 Vista brightness will not work after driver update

  Hey,.

  I can't adjust my brightness. I ' t worked fine till updated my video driver.
  I downloaded the driver from NVIDIA.com. The 7000 series. I have a 7600 graphics card.
  Is that I have try to change the brightness using Flash cards blocked the entire program. And in the mobile Center
  the brightness option went :(

  Can someone help me and maybe keep the latest driver?

  Thank you
  Mathijs

  Hi Mathijs

  What is 7 FN + F6 key combination? You can use this option? Please let us know if you can change the display brightness in power options (check in all three plans).

• AppleTV doesn't work after software update

  I have a new generation AppleTV and upgraded to the latest version of the software, as it has been invited. After the upgrade, I can't see an image more. It is not the HDMI cable that I joined my old AppleTV and it works. And now the part of the frustration. I called Apple Support and they advised me to go to the Apple Store to get an Exchange because my unit was still under warranty. However, the new unit had the same problem. He works first, and after the upgrade, it became a brick.

  Hello. Please see my response to your previous post Re: Apple TV update allows playback of video tvOS 10.0 breaks.

• P0R94EA #ABU: brightness and HDMI does not work after driver update

  Hello

  I get a notification to update my drivers for HP Support Assistant that I took and I installed all the drivers involved and since that I can't not change the brightness of my screen or use the HDMI for display on my TV. I don't have the updates has been "Intel high definition (HD) Graphics Driver.

  Can someone help me with this please have tried different things from other sites, but nothing has worked.

  Hello

  Is there an improvement if you install the earlier version at the following link?

  http://ftp.HP.com/pub/SoftPaq/sp72001-72500/sp72107.exe

  Kind regards

  DP - K

• S3-391 Acer wireless network adapter does not work after driver update

  Hi, I have an Acer Aspire S3-391 running Windows 7 64 bit and I have recently updated my card (Atheros AR5BMD222) wireless network to the latest version of such 10.0.0.274 as recommended by the Acer site.  After updating the driver, I can no longer connect to my wifi at home.  When I try to connect, I get the message that no wireless connection is available (even if all my other devices can see the wifi network) and when I diagnose the problem, it is said that there might be a problem with the wireless network card and that windows could not automatically bind the ip stack Protocol.  I tried to uninstall the new driver and reinstall one old and running a system restore before installing the new driver, both with no luck.  When I try to manually configure a wireless connection, I get message "an unexpected error has occurred."  I have an automatic DNS and IP address, and when I look at my ipconfig, IP, DNS, DHCP, etc all have addresses.  Any help would be greatly appreciated, thank you.

  And while playing, I managed to fall on a solution.  When I looked at the properties of my wireless network card, I have disabled NetBIOS over TCP/IP and now everything works fine.

• Epson v500 Scanner does not work after driver update!

  I recently bought a V500 photo and scanned my first 35mm using Epson Scan v3.7.4 negatives. The colors seemed off so I download and installed the latest v3.7.7 of support to Epson.ca hoping that it might help.

  Following the upgrade of the driver, the scanner has stopped working! Loads of Epson Scan, but after 5-10 seconds, I get the message: "no response from the scanner. Make sure the scanner is turned on and connected properly. If you use the transparency feature, remove the reflective document mat. »

  Then I restored the latest install w / restoring Windows but still could not get the job to scan. I drove back to the pre - Epson scan install date and tried to reinstall the earlier version but still no luck to get scanner work.

  I then followed the steps of uninstall on the Epson.ca support site removed all the drivers and the software with the scanner turned off and unplugged. Then I reinstalled the old version of Epson Scan of the CD because he had worked at the start. I reconnected it the scanner it plug it in and turn it on. But it still does not work! Ditto for uninstall and reinstall with the latest drivers.

  Notebook P7350 using Windows 7 32 bit SP1. Scanner is connected directly on the laptop, not through a hub. I tried all 3 ports USB in the hope one would work, but no luck. All connections between the pc and the scanner seem robust.

  Any suggestions to get scanner work?

  Thanks for the reply of adeline. In the meantime, Epson come back to me when I contacted them again but only after I have disabled cookie blockers in Firefox when visiting their support site. The first time I've done this, and the support form has not sent correctly.

  It turns out that the scanner must be completely turned off and unplugged then reconnected after that driver installed. I discovered one of the records was not too tight that it should have been :-0 if I was sure I had checked it earlier.

  Thanks again.

• Envy dv7: Bluetooth stopped working after driver update

  After installing the update of the Toshiba Bluetooth driver through the window update, my mouse Bluetooth is no longer in effect. Everything was going well until the update has been installed.

  I rolled back the update of the driver in the Device Manager and this has solved the problem.

• Mailto doesn't work after updating FF 42.0

  Mailto doesn't work after my last update. The entrance of mailto is not under Tools > Applications and there is no drop-down list to add an entry. My default e-mail program is Windows Live mail.

  Hmm, mailto certainly should not be missed.

  Sometimes, the file that stores these actions of the Manager/download application is damaged. As it is difficult to change, when there is a problem, we offer usually when you rename the file and allows Firefox to rebuild the Windows registry. Who cannot help if mailto is missing from the registry, but I think it's worth a try:

  Open the settings folder (AKA Firefox profile) current Firefox help

  • button "3-bar" menu > "?" button > troubleshooting information
  • (menu bar) Help > troubleshooting information
  • type or paste everything: in the address bar and press Enter

  In the first table of the page, click on the view file"" button. This should launch a new window that lists the various files and folders in Windows Explorer.

  Leave this window open, switch back to Firefox and output, either:

  • "3-bar" menu button > button "power".
  • (menu bar) File > Exit

  Break while Firefox finishing his cleaning, then rename the mimeTypes.rdf to mimeTypes.old (or another name of your choice, in the case where you decide to roll back this experience).

  Launch Firefox back up again and return to the Options page to specify your preference. Mailto appears once more?

• Delete buttons do not work after the update of 10.11.16.

  Delete buttons do not work after the update of 10.11.16.  The delete button works if I pointed out and then delete, but not if I use the "back" button or try a removal of uniqueness.  It is a problem in all applications.  I tried it in textedit, search google chrome, safari search and find finder engine.  There seems to be a 'problem' of the keyboard' as far as I know nothing happened to my keyboard, IE the spilt coffee, that recent warming has been updated to 10.11.16.  I use an iMac (27-inch, late 2009) with i5 clocked at 2.66 GHz, running OS X El Capitan.

  Any suggestion would be appreciated.

  Greetings, r.fromstouffville!

  It seems that the 'Delete' on your iMac keyboard key works as it is supposed to be after update to OS X 10.11.6. I'll be happy to help you get these keys working again.

  Reset of the controller management system (SCM) on your Mac - sometimes it's a matter of simply resetting your iMac SMC. Open this article and scroll down to "Reset the SMC on Mac desktop" section and follow the steps there.

  Try safe mode if your Mac does not start -even if your iMac, safe mode startup make sure it starts successfully.

  How to test one question in another user on your Mac account - use this article if restarting in safe mode did not help.

  Use Time Machine to back up or restore your Mac - if your keyboard does not always work as it should, I recommend you save your iMac to ensure that your personal data are safe. It is always better "to have" a backup for a backup "need."

  On OS X Recovery - if you have reached this point, you encounter the same problem in a test user account, that would mean it is a system-w. Start your iMac into Recovery Mode and reinstall the operating system.

  Thank you for the communities of Apple Support!

• HP Pavilion: Bluetooth doesn´t work after installing Windows 10

  Hello

  Doesn´t Bluetooth work after I upgraded my OS to Windows 10.

  Can someone help me please?

  JimWieder

  JimWieder

  Thanks for the reply and the information updated. Check the link to your model and you will keep. Thre is no specific driver for Windows 10 for this computer for now, but there is a Bluetooth for Windows 8.1 driver.

  I could start with the HP Support Assistant, as I mentioned and see if she can find something for you. It is useful to have, as it will seek new pilots as part of its function.  If this does not work for you, then you can try to install the driver Windows 8.1 of the support page.  Broadcom Bluetooth driver

  Try to install such what, first and then Bluetooth test. If after the test, you still have trouble with the Bluetooth does not, try the method of this other link I posted on how to install a driver using compatibility mode, and then see if it will work for you.

  Here are other pages that can be useful for you in troubleshooting and testing, and also that of Microsoft.

  HP computers - using devices (Windows, 10, 8)

  HP computers - understanding and troubleshooting Bluetooth wireless technology (8.1 Windows, 8, 7, Vista, XP)

  Connect to Bluetooth devices - windows.microsoft.com

  I hope this helps.

• DVD player doesn't work after installing SP3 for Windows XP.

  DVD player doesn't work after installing SP3 for Windows XP. That it disappeared from "MY COMPUTER". Device Manager sees it, but there's a yellow exclamation mark over it. See the BIOS of the motherboard and it still works in the BACK. I know SP3 is a collection of updates, but I'm not sure that is my problem. I suspect it's one of the more recent cause I have Windows automatic updates is turned on. Thank you.

  Hello Superhornet142,

  Thank you for your message.  Click HERE and run the FixIt!  Please let us know if it did or did not help to solve your problem.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• AutoFill does not work after last update 3-6-3

  AutoFill does not work after last update 3-6-3

  is after update

  See control if Firefox automatically fills in forms

  Start Firefox in Firefox to solve the issues in Safe Mode to check if one of your modules is causing your problem (switch to the DEFAULT theme: Tools > Modules > themes).
  See the extensions, themes and problems of hardware acceleration to resolve common troubleshooting Firefox problems and troubleshooting questions with plugins like Flash or Java to solve common Firefox problems

• HP ENVY dv6 Notebook PC: press the / STOP the envy of hp dv6 7204se do not work after the update of windows 10

  the power button of my hp dv6 7204se envy key do not work after the update of windows 10

  any help on this please?

  .