C code for table of labview implementation

Similar Questions

• Need help with LabVIEW code for motor control.

  Hello

  My name is Sasi. I'm a grad student BME working on my thesis topic of assessment for back pain spine implants. To do this, I'm building a test machine that would apply pure moments of a specimen of the spinal column. I use LabVIEW 8.5 to implement the control of a brushless AC servo motor. My requirement is

  Step 1: Initialize the engine.
  Step 2: Start moving it to a uniform to the right PLAN (this value of RPM too user can enter).
  Step 3: while doing step 2; at the same time read the couple cell data (acquisition of data using Asst.). DAQ o/p is 0 v to 10 V; 0 v is 10 Nm n
  10 v is + 10 Nm
  Step 4: What torque reached + 10 Nm, i.e. 10 V, the engine stops.
  Step 5: from the position where the motor stopped (IE not need to return to the initial position) start moving in the opposite direction to the same
  Uniform rpm as in step 2 at the reading of data in the cells of the couple.
  Step 6: once more what torque reached-10 Nm, i.e. 0 V, the engine should stop.
  Step 7: Repeat "Step 2" to the "step 6' 3 times.
  Step 8: Reset engine position.

  So far, I managed to get the engine to move backward @ a desired vel, the accl, deceleration for 3 cycles before n n. I enclose my code. I have a problem inserting the code for reading DAQmx amidst all this. Can someone help me.

  Thnks,

  Sasi.

  Hi Sonia,.

  I took a quick glance to your problem and I think I have a solution for you.  I certainly agree with the suggestion of the use of parallel loops Lynn.  This will allow the portion DAQmx run uninhibited by the part of the motion, and vice versa.  In addition, you need only perform an iteration of the loop of the movement whenever the voltage level exceeds a threshold.  Thus, by performing an iteration on the code of movement in the same loop are you iterate over DAQmx code, you essentially waste processor.

  I created a VI that should do what you are wanting.  I tested it on me and it works very well.  You have a tweak a few things to apply to your system (such as motion Council DAQmx and physical channel ID, etc.).  I used two parallel loops and event programming.  Basically, the loop of movement starts the engine turns at the specified speed.  Once the engine is running, he expects the DAQmx loop to tell him that the voltage value has crossed the threshold.  When the voltage value exceeds the maximum threshold (I put a value slightly less than 10 to jitter and saturation), the DAQmx loop indicates the loop of the motion that it may end its iteration.  The motion loop stops the motion, causes a reversal and repeats the motion.  Once the movement has begun, he expects the DAQmx loop once again to tell him that a threshold was held, but this time, it's looking for a minimum threshold.  I used "Occurrences" to implement the event programming in LabVIEW.

  I've commented the code pretty thoroughly, so I hope that comments will answer all remaining questions.  The advantage of using programs that focus on the event for this is that you save time processor, and your movement is more closely synchronized with the DAQmx.  Instead of one iteration of the loop of movement as fast as you can, updates every hour, you just put in pause and wait for the other loop to tell you when to start up again.  Meanwhile, the processor doesn't have to worry about an iteration of this loop over and over again.  In addition, when the accident occurs, you catch him immediately, instead of having to wait until the next iteration.  Thus, you are more closely synchronized with the DAQmx code portion.

  I hope this will help you.  Please report if you have any questions about the code or its implementation.  Good luck!

  
  

• Table for the code for method of payment for the suppliers site

  Hi all, does anyone knows how to get the value for the code for method of payment for the suppliers site in R12.1.3? I don't speak from that in the following path: 1 Paybles responsibility 2. Suppliers 3. Request for a 4 suppliers. Click on details of payment 5. Scroll to supplier Sites and press the update button 6. Note that, for example among the payment methods is checked as default thanks in advance, A.Stoynaov

  Hello

  Please check this note that contains the query:

  Default values for method of payment for providers at the level of the Table (Doc ID 737128.1)

  You can use this query to view the lines for a given provider site:

  SELECT *.

  Of iby_ext_party_pmt_mthds IEPPM

  WHERE IEPPM.ext_pmt_party_id IN

  (SELECT IEP.ext_payee_id

  Of iby_external_payees_all IEP

  WHERE IEP.supplier_site_id IN

  (SELECT APSS.vendor_site_id

  Of ap_supplier_sites_all of the PSA, ap_suppliers APS

  WHERE APS.vendor_id = APSS.vendor_id

  AND APS.vendor_name = '. '

  AND APSS.vendor_site_code = ''));

  Concerning

  Joel Purswani

  Support of Oracle

• Different codes for different - looking of table (but the same memory-wise)

  (I've posted something similar here as well, but it's kind of emergency):
  http://www.Java-forums.org/advanced-Java/40756-HashMap-treating-isomorphic-but-different-objects-same-key.html)
  
  Hi all
  
  I am trying to program the Reversi game on my computer and I represent the game like a lookup table tree using a hash table.
  Any available to the Commission is represented as an int. [8] [8]. The hash table takes a configuration of the Board of Directors as a key, and is meant to restore an object that contains information about the possible move.
  
  But I have a problem. Suppose I have a Council (4 x 4 for readability):
  
  Code:
  Board of Directors of int [] [] = {{0,0,0,0}, {0,0,0,0}, {0,0,0,0}, {0,0,0,0}};
  
  And suppose that it gives a hash code of say "1607178090".
  
  Then, when I change the Council;
  Board = {{0,0,0,0}, {0,0,0,0}, {1,1,1,1}, {1,1,1,1}};
  I want the hash to be different code, then my hashMap will recognize it as a different Board.
  
  
  ---
  
  I tried to make a Matrix object and dominant equals and hashCode, but I'm not sure what to change. The Java API says that the hash code for the tables is based on the content, even if the following code renders the same code to hash twice. I don't really understand this:
  int [] a1 = {0,1,2};
  System.out.println (a1.getHash ());
  A1 [0] = 1;
  System.out.println (a1.getHash ());
  
  
  
  
  Moreover, my Matrix class is:
  to import java.util.Arrays;
  
  public class {Matrix
  public int [] [] Council;
  public matrix()) {}
  }
  
  {public matrix (int [] [] b)
  Board = b;
  }
  
  @Override
  public int hashCode() {}
  first final int = 31;
  int result = 1;
  System.out.println ("based hash code calculation on :"); ")
  first = result * result + Arrays.hashCode (board);
  for (int c = 0; c < board.length; c ++) {}
  for (int r = 0; r < board.length; r ++) {}
  System.out.Print(""+Board[c][r]+"");
  }
  System.out.println ();
  }
  System.out.println ("return" + result);
  return the result;
  }
  
  @Override
  public boolean equals (Object obj) {}
  If (this is obj)
  Returns true;
  If (obj is nothing)
  Returns false;
  If (getClass()! = obj.getClass ())
  Returns false;
  Matrix other obj = (matrix);
  If (!.) Arrays.Equals (Council, other.board))
  Returns false;
  Returns true;
  }
  }
  
  Published by: 845707 on 19 / mrt / 2011 02:20

  845707 wrote:
  I don't really understand this:
  int [] a1 = {0,1,2};
  System.out.println (a1.getHash ());
  A1 [0] = 1;
  System.out.println (a1.getHash ());

  Me neither does table have a method called "getHash();" these days?
  In case you meant hashCode(), what you call it is hashCode() of the object, which would remain the same for the object during its lifetime.

  In your example code you use correctly Arrays.hashCode (), then why did you write an example that does not represent your actual code?

• LabVIEW code for multiple counters from source

  Hi all

  I developed a code for an instrument of 24xx keithley of interface, but now I have a doubt that if I want to do a few 10 instrumets interface both then, how can I write the logic for this.

  Please suggest me its urgent need. several instrumrnts in the sence as 24xx, 26xx like that.

  What kind of physical connection have you instruments? Controlling several instruments is not very different from one. You may need to provide external triggers take simultaneous readings and structure your state machine to do any initialization only once.

  Your question is fairly generic. What specific problem you observe?

• Raspberry PI connected with usb for laptop with Labview

  Hello

  Please allow me to introduce myself: my name is Bob and I just graduated from the Bachelor of applied science (Physics), in the Netherlands. In education, I followed a course of programming in Labview. However, the course was not very well if I want to start from scratch. (my programming skills are very poor).

  My goal is to learn the basics of programming in Labview. I want to measure the temperature with a probe for example and read this in Labview. I need a data acquisition for this system. I have a raspberry PI in my possession and I was wondering if I could use it to read the temperature from the USB port of my laptop using the PI raspberry. Is this possible? And I have to run some sort of program on the raspberry PI? Or I could better use another device (Arduino maybe?).

  I hope someone could help me to help me get started with Labview. I'm looking forward to learn how to work with Labview and launch a few projects.

  Thanks in advance,

  Bob

  Are you comfortable with writing code on the invoice, pro forma raspberry? This is where you write the code for the acquisition of data and code to send it on the usb as a RS232 serial port. The LabVIEW program would receive all this and it is a very simple program. There is a tool called Linx box that does all this for the arduino.

  https://www.labviewmakerhub.com/doku.php?id=libraries:Linx:start

• example code for NI9411

  Hello

  I'm looking for a simple example of code for NI9411 (FPGA code and the host). I searched in the examples that come with LabView but I have not achieved anything.

  Thanks in advance.

  Here is an example that you can use with the NOR-9411.  If you are looking for 9401 in the Finder for example of OR, you can also find other examples that were not written for the 9411 specifically, but you can modify it to work with her.

  Brandon Treece

  Technical sales engineer

  National Instruments

• Source code for Java?

  Is it possible to get access to the source code for the library API Java BlackBerry?  I'm working with the protection of a set of cryptographic keys using the cleaner memory.  I currently use the LDAPPasswordCache to store my keys, because it is the only class in the library that implements the MemoryCleanerListener.  I want to develop my own key storage class, but I'd love to see how LDAPPasswordCache is implemented so that I can use as a template for my own class.

  short answer: no

  long anser: do not hesitate to apply to rim for her

• Potential problems for tables without primary keys and unique keys

  GoldenGate 11.2.1.0.3/Solaris 10
  DB: Oracle for Oracle (Source and target is 11.2.0.3)
  Topology: unidirectional
  
  
  In our one-way configuration GG, little of the tables being replicated is not a primary key or a Unique key.
  
  Last week when we have implemented GG for the test, we received warnings for these table below.
  

  GGSCI > add trandata WMHS_UD.crtn_dtl
  
  2013-01-12 11:34:33  WARNING OGG-00869  No unique key is defined for table 'CRTN_DTL'. All viable columns will be used to represent the key, but may not guarantee uniqueness.  KEYCOLS may be used to define the key.
  
  Logging of supplemental redo data enabled for table WMHS_UD.crtn_dtl.

  Replication seems to work very well for these tables.
  
  Googling, I think that there may be performance degradation when you replicate tables without PK or the United Kingdom.
  
  But are there other potential problems such as data of a certain kind not replicated to the lack of PK/UK?

  It really depends on the data.

  By default, GG is combining all columns as a virtual primary key but don't no conflict control by default. So when you can be sure that the record you insert into the table is unique, then it will work.
  BUT as soon as you insert the same record, which is already inserted, then you will encounter problems.

  Let me show what happens when you use an initial charge because it makes it easier to describe:
  We start at 10:00 the capture for a table. Now, you insert a record at 10:00 in the tables. When you now start an initial charge to 10.02, then check you have inserted in the database to 10.01 will be repeated two times. During the IPL as the initial charge is made to 10.02 and it includes data of 10.01 AND it will be replicated again through the process of capture/replicate.

• Flash CS4 plug for table swf?

  Hey everybody.  Does anyone know if there is a Flash CS4 free plug-in that creates a table of swf that loads external swf in order and can control the script without having to mess with Actionscript?  I don't know yet what to put in Google looking for such a plugin.

  Right now, I have a table like that.  I got the code from some very helpful people here.  I still don't understand most of the code, however, so I'm wondering if a plug-in could do the same work as Actionscript.  I have the code for my Flash file in another thread of discussion, and I'm trying to get my file to stop looping SWF when it reaches the end of the array.  If anyone is curious to see the code, I want to talk or if they know how to solve the problem of the loop, here's the link to this thread:

  http://forums.Adobe.com/message/3417613#3417613

  use:

  var listener: Object = new Object();
  var mcl:MovieClipLoader = new MovieClipLoader();
  mcl.addListener (listener);

  When the SWF load, put in place to constantly check its current image
  against the total number of frames, and so those that match, the SWF is done playing.
  If this is the case, then load the following.

  listener.onLoadInit = {function(targ:MovieClip):Void}
       targ.onEnterFrame = function (): Void {}
  If (this ._currentframe = this ._totalframes) {}
  loadNext();
  delete this.onEnterFrame;
  }
  }
  }

  Swf buttons next and previous

  function loadNext (): Void {}
   
  If (currentSwf<>
  currentSwf ++;
  loadSWF (currentSwf);
  }
  }

  function loadSWF (nextSWFToLoad) {}
  mcl.loadClip (SWF [nextSWFToLoad], theTargetClip_mc);
  }

  loadSWF (currentSwf);

  function loadPrevious (): Void {}
  -currentSwf;
  if(currentSwf==-1) currentSwf = swfs.length - 1;
  loadSWF (currentSwf);
  }

  previous_btn.onRelease = loadPrevious;
  next_btn.onRelease = loadNext;

  Swf previous and next buttons end

  'Play' button

  play_btn.onRelease = function() {}
  theTargetClip_mc.play ();
  }

  Pause button

  pause_btn.onRelease = function() {}
  theTargetClip_mc.stop ();
  }

• Problem with code in tables

  Hi, first post... New DW cs4 user.

  I am trying to list a few items for sale on a Web site. The company that performs the processing of online payments generates a code for me to use to produce a button for buying... and there is the challenge.

  I'm putting the code in a table and its does not work. The code is a "payment button" generated by a payment company called Skipjack. If I place the code, say... on the bottom of the page it looks fine. But I need to go to a specific place on my Web page, the payment button. Please help... pay the boss awaits! Laughing out loud... Here is the page... http://www.ambitioncharters.com/packages.html ... the button is there, but I'm trying to put the different packages on the page... and then put the code for the price to the right of the product discrpition or under... I thought that a table would be way more "pretty" to achieve... but like I said, when I put the code, they give me the table... the code appears in the cell of the table instead of the button I need to go there... weird!

  Here's the code...

  <!-beginning of the "good ezPay command'-> code
  

  
  < input type = "hidden" name = "bonito" value = "D/inOUaqBqrBUe5T5fdgKs9zMySFmAjH21Kmx/TaWu0uAeseJidIoeVbnct7MtJyfdMz8NeGUuJgfeaSSe ZTq9UtbQLaXoQFowULZj41NgUFFbzT4cE1ApCJDP8RWU6pLPOEIuJeaDPQ4ia1OEzHRh7dR7PkyLkQyTmA9wrm2ULU HEKGtMpDU8fRvMx3DjnDBcP/0eDi5A8jkvcOt4/3qRCVUoTbNVqYaREzlzZoAnkQm8VLJI3JoU54wC8wTEewiKfXRr sTG5Bvv/XZmZHB3XXnng2Dn7nGZNkTz1rcJT1r5O4mM6 + oVYt3AnvP2jVi/l12 + oz + dAm UjyJneyJRstdu50eBHzv1E1Y + V9lptkBBS2xObmAF/urmWmGAtuc0ILByOKFe2Wg22zsuvMY2Tn3GBxe1sGC7d9uFl2gay3LePhfBG7 + gHvfSji SB6h5M0m76CWWjUHXikVxX2VKNtm3o + JAhSBE + AemfUWTrdwGcMZbljp7mBRGmiMOXz/2hc8MekCV/EdI9KDx1gt6C pw ==" / > "
  < input type = "hidden" name = "ezPay" value = "ZWyf7/x88PNVT9almNuR9MsthaKDhaRZ8QW3IiLIDk4 =" / > "
  < input type = "hidden" name = "creator" value = "44H7TtPK3SQ29yfCpHy5EA ==" / > "
  < input type = "submit" name = "Button" value = "PlaceDeposit" / >
  < / make >
  <!-end of "good ezPay command'-> code

  kylesalone wrote:

  Yes, it's true... the code, not the button, appears in the cell...

  I'll post the page with errors on it... now, as you can see, the formatting is quite climb... It's at least on my mozilla.

  All its supposed to be left indent... some is centered... and some of the 'deposit' buttons do not work.

  http://www.ambitioncharters.com/packages.html

  Suggest you read the code for the button one that works and then look at the code for those who are not. You will see the button that works is encapsulated in a form tag. This provides the necessary information as what is supposed to happen when the button is clicked.

  method https://vPOS.Skipjack.com/ezPay/Order.asp"="post">

  Not sure why two of the buttons are centering upwards and not left aligned... the code is a bit messy. If you insert your cursor to handcell that contains buttons and tables and go to the property inspector and choose horizontal align left in the menu drop which seems to do the trick.

  Its something to do with your styles css because if you detach all the buttons left alignment. And regarding the css well anyone who attached requiring many models to a page of shot in the nuts.

• How to change the default color for tables/pivot tables

  Can someone share how to change the default font color or background for tables and PivotTables? In my view, there is a CSS or XML setting I need to change.
  
  It is difficult to read the text when negative numbers are RED and the overall totals have a default NAVY background fill. I'm trying to find out how to change the color of these without doing it manually to each report.
  
  Thank you.

  Jin

  For pivot Table

  Go to OracleBI\oc4j_bi\j2ee\home\applications\analytics\analytics\res\s_oracle10\b_mozilla_4\views.css

  Change the PivotTable section code

  For table veiw

  Go to OracleBI\oc4j_bi\j2ee\home\applications\analytics\analytics\res\s_oracle10\b_mozilla_4\views.css

  Change the section of the Table

  PS:take backup your original file before you edit any css file. Don't forget to give the points/close the thread

  Thank you
  saichand.v

• CSS code for the background of the image problem fixed

  Hello world
  I struggled for almost 2 days on and outside to try to understand why I can't get the codes for a fixed background work properly. I'll copy the code here directly and hope that someone can see what the problem is. I also give a link to the site I'm just starting to be implemented.
  http://seanshaw.NET So you can see the source code here... Any help would be greatly appreciated as I have tried 3 different versions of the code fixed background and none of them does not work for me. What Miss me? :)
  
  Thanks for any help on this problem... Best regards, Jo Whimzicals.com
  
  The code that I currently use is this one... I take you from the top to the body tag:
  
  <! DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional / / IN".
  " http://www.w3.org/TR/html4/loose.dtd" >
  < html >
  < head >
  < style type = "text/css" >
  body
  {
  background-image:
  URL ('BckgndHome.gif');
  background-repeat:
  no-repeat;
  background-attachment:
  fixed
  }
  < / style >
  < title > Sean Shaw Art, Art of Sean Shaw < /title >
  < meta http-equiv = "Content-Type" content = text/html"; charset = iso-8859-1 ">"
  < style type = "text/css" >
  <!--
  body, td, th {}
  do-family: Verdana, Arial, Helvetica, without serif.
  }
  {body
  background-image: url(Home/BckgndHome.gif);
  }
  {.style2}
  do-size: 18px;
  color: #FFFFFF;
  }
  .style3 {color: #FFFFFF}
  ->
  < / style > < / head >
  
  < body >
  ==============================
  Just to clarify things, I also tried these two codes, that makes perfect sense to me, but they still do not work for me.
  ==============================
  < style type = "text/css" >
  Body {background: url (fixedbg.gif) set of Center no-repeat ;}}
  < / style >
  =======================
  ... and this one...
  
  < html >
  < head >
  
  < style type = "text/css" >
  body
  {
  background-image:
  URL ('image.gif')
  }
  < / style >
  
  < / head >
  
  < body >
  < / body >
  
  < / html >
  
  

  Ahhhhhhhh, Thank you VERY MUCH, ACE! I found and removed the second command line, and you were quite right... the bottom now remains in place and works perfectly. Thank you for taking the time to help me... Awesome. Have an awesome Sunday... Best regards, Jo :)))

• view the code for two different pages at a time

  HI - in other editors I've used I've always been able to implement the code for two different pages so that I can watch side by side to compare. I can't find a way to do this in Dreamweaver. Anyone know if this is possible?
  Thank you

  Found. Always after asking for help! This is the "cascade" in the Windows menu.
  Thanks anyway!

• Examples of code for the robot LDAP plugin is missing

  I downloaded and installed ITS 10.1.8 version but the sample code for the robot LDAP plugin isn't the case to find. The "sample" directory is missing. The example of code removed for any reason or is it replaced by something else? We must be able to search an LDAP compatible to v3 for our new dashboard application.
  
  The document "Secure Connector Software Development Kit" for ITS Version 10.1.6 says the following:
  -Oracle shipped three sample plug-ins that supports analysis, analysis of database table and analysis file LDAP directory.
  -ORACLE SECURE ENTERPRISE SEARCH comes with three sample plug-ins sub $OH/search/sample/agent.

  Yes, samples of tracks were removed in 10.1.8 because they have not been sufficiently tested, or considered good enough to ship.

  However, I have the LDAP robot and I'll be happy to send it to you (STRICTLY no guarantee, of course!) If you leave me an email for roger dot ford at oracle dot com.