Call between C20 composition of address Ip without VCS

Similar Questions

• I can't make call between Tandberg C60 using the Sip Protocol

  Hello

  I tried to call between Tandberg C60 codecs with the SIP ends, unfortunately the call failed to connect. His poster is not the message "connecting" either.

  Then I changed in the Codec c60 (both sides c60) H323 Protocol, then call connects and works well.

  Please any idea.

  Thank you.

  Kind regards

  Henri El Salvador

  ==========

  VCS ver: X7.2.1

  TANDBERG Codec C60;

  Codec1: TC4.2.4.296355

  Codec2:TC4.2.4.296355

  You can't just dial the SIP with an IP address only - that is not a valid format of SIP.  There must be a [email protected] / * / or [email protected] / * / (IE [email protected]/ * /) format.

  In your example above, you should be able to dial '[email protected]/ * / "or"[email protected]/ * / "-these two are valid SIP addresses.  The right 10.88.17.5 the IP address is not.

  PS - As mentioned by Patrick, you really should upgrade your software on your endpoints to a newer version.  There is a security notice that should help you get the new software, even without an active service contract: http://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20140605-openssl

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Is it posible to allow access between the host and virtal machine without wired network?

  I want to use my laptop to show him that I did in the virtual work to other people at my home.

  However, the laptop is ofen not allowed access to the network in their office.

  Is it posible to allow access between the host and virtal machine without wired network?

  VMware player

  My virtual machine is filled to the physical network adapter and use the static IP address.

  Brad

  Setting of the virtual machine: filled

  Change that to each host only (what Continuum called VMnet1) or NAT (VMnet8).  Both use a separate virtual NETWORK card to connect the physical computer virtual host, independent of any NETWORK adapter on the host.

  ... Since the machine host (win7) could not get IP, ping fail to VM (192.168.1.5)...

  Because the connection between the guest and the host is through a separate NETWORK card, you must use the 'other' IP address.  Access a prompt on the host computer and type IPCONFIG to view the IP address of VMnet1 and VMnet8 NIC.  Then use this IP address instead of 192.168.1.5.

  And when you have changed the network management modes (i.e. of bridged to host-only), Windows does not automatically renew its IP address.  The virtual NETWORK card uses a different subnet if you need to renew your DHCP lease or change your static IP address to work with the new subnet.

• Is it possible to send an email to everyone in my address book WITHOUT typing/select each address individually?

  My old e-mail address will be aborted and I need to tell everyone in my address book of Mozilla Thunderbird. Is it possible to send an email to everyone in my address book WITHOUT typing/select each address individually?

  Hello zmerill
  Yes it is possible and simple to do.
  -In the composition of the TB window, display on the left address books
  -Select the address book you
  -Select normally the first contact (left click)
  -by pressing the SHIFT key, select the last contact (-> all selected)
  -just below the last contact, use the button you want.

  In an address book, it is also possible to create a mailing list.

  Stone

• Restricting calls between a subarea and specific extensions on Cisco VCS

  Hello, I use Cisco VCS 8.5.3, my goal is to restrict calls between a subarea and specific extensions.
  I tried following solutions:

  1. Download of XML strategy
  2. Use of political appeal web interface in order to limit calls

  XML file:

  
   
   

  
   
     
     

  
     
     

  
     
     

  
       
     

  
     
   

  
  
  

  But when I apply the XML file, or try using the web simple rule (for example: 11111 12222 destination source, dismiss the action) I'm still able to place the call to 11111 to 12222.

  What can be the cause of the problem and what else can I try to be able to prohibit calls between a particular Subzone and exentions?

  Attached, is an example of CPL script that should work.  Using this script, CPL, I was able to block calls to a subarea set to a destination alias located in the subzone of default and was always able to call any other end point in the default subfield without problem.  Note that you must enter the name of the subarea, as you have configured on the VCS, including spaces if they exist.

  The scenario is based on the example of CPL "limiting access to a local gateway" X8.5 VCS Administrator's Guide on pg 413, other documents of CPL reference and examples can be seen starting on pg 410.

• VCS CPL block call between subareas

  Hello

  I'm looking for, it is possible to create a script to block calls between the sub-areas, I mean, I don't want to, for example, that sales of subarea may call for subzone Marketing.

  I do not have different Alias prefix, the prefix aliases are the same in the two Subzones, is possible to block call due to the IP address or the name of the subfield?

  In the CPL extensions xsd file and the XSD of CPL file I have found no topic block by IP address or between subzones.

  I could find the following example script:

  *****************************************************************************************+

  "xmlns:TAA ="http://www.tandberg.net/cpl-extensions"

  "" xmlns: xsi = "http://www.w3.org/2001/XMLSchema-instance"

  xsi: schemaLocation = "urn: ietf:params:xml:ns:cpl cpl.xsd" >

  *******************************************************************************************

  But only to block calls between DefaultZone and DefaultSubZone.

  Thakns in advance.

  Best regards.

  Hello

  at the time where the CPL is treated, the location of the destination device is not yet known, and we cannot therefore CPL decisions based on the zone of destination or of the subzone.

  To work around this problem, you can for example use a prefix/syntax unique to each subarea, so that you can identify implicit destination/subzone area according to this prefix/syntax.

  It would be also possible to 'outsource' this decision-making process with the use of political Service, which is a service area that can be highly customized. The external policy server could for example have a SQL database containing information on all your devices and their associated area/sub-area and base its decisions on the information which includes the VCS on the pseudonyms of source and destination for a given call, as well as a variety of other measures.

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/VCs/config_guide/Cisco_VCS_External_Policy_Deployment_Guide_X7.PDF would be a great starting point if you want to deepen the policy Service.

  Hope this helps,

  Andreas

• How to export a subdirectory of my address book without exporting the full address book?

  I use subdirectories (contact groups) in my address book for different groups of contacts. I need to move a group to a different mail client, but when you use the export function, it doesn't seem to be a way to select a single group. The export function exports the entire address group without taking into account my groups of void. Is there a way to get around this?

  Yes, by selecting the addresses before clicking on tools seems to do the trick

• Is there a way I can share files between users on the same Mac without an internet connection?

  Hello world!

  Quick question here: is there a way I can share files between users on the same Mac without an internet connection?

  I have two users say that A and B. If I go the long way via the 'Go' menu > 'Computer', I ended up being told to contact my computer or the network administrator for assistance. Both users are admin one and file sharing is allowed in system preferences... I have to admit that I use 10.9.5 because my MacBook Pro would not work with OS Xs national parks.

  Any ideas would be cool because I'm sure that it used to work fine with "Snow Leopard" without being connected to the internet - or should I just send an email to myself and recover the files on the other user :-) to recover my USB is

  Choose go to folder from the Finder Go menu, provide/Users/Shared/as the path and place the files.

  (142147)

• Cannot connect call between two SX20

  Hello world

  I've implemented two Cisco SX20 units at two sites. When you attempt to place the call between two units, it is unstable. In particular, sometimes the call is connected, sometimes, it is not connected even if ping, tracert are Ok. It's very strange. I'm sure that the SX20 unit works well. If I make a conclusion that there is a problem with my network but I don't exactly know why.

  All the world is facing this problem before?

  Dzung.

  Hey yours,

  Disable NAT if you do not use.

  Also useful to configure QoS, check on your link packet loss and bandwidth.

• Limit the number of calls between areas of VCS/subareas?

  Hello

  I wonder if there is a way that we can limit the number of calls between two subareas, areas or VCS.

  The script as below:

  VCS-E (owncompany) < -----neighbor/traversal/dns="" zone="" over="" internet------=""> > VCS-E (partner)

  My intention is to limit to 5 video calls from VCS-E (partner) so that the 6th call (dial in endpoint) will be blocked.

  I know that we can control the total bandwidth between areas using links & pipes but that does not stop the remote end to lower their rate of recall and deal with several endpoints.

  Thank you.

  Hi Hafiz,

  have you tried to disable the 'downspeed by mode of appeal"in a configuration of Bandwidth?

  try disabling the "downspeed" by call OFF mode under VCS config-. > bandwidth--> configuration.

  This will not allow the calls get the downspeed but it must block because of insufficient bandwidth.

  Thank you

  Alok

• Call between 3200 TP and question TP 1300-65

  Hello

  question of pls, an active call between 3200 TP-TP 1300-65, which is the normal behavior of the output display perspective TP3200 or 3 screens? (showing the room TP 1300-65) He must have the intermediate screen active and left and right are idle black?

  Not having does not have access to one, I am unable to test, but yes, I would say that the TX-1300 (being only a single display system) only appear on the single (in the middle) screen of the CTS-3200 and the other two would remain empty (or display other connected parts).

• Different plan back color between the composition and rendering after adobe media encoder

  I discovered after effect...

  I have a problem of correspondence between the composition and the final rendering through adobe media encoder

  The color of the background composition of Loire (regardless of color) and always a background BLACK after the adobe media encoder

  

  Despite several manipulations by changing the settings I can't solve the problem.

  A little help would be welcome, thanks

  The composition background color will never surrender.  Hug composition background color will never, not even with the record locator.  The background is transparent and will always be unless you fill it with pixels. Unless you choose a format that supports Alpha channels, Alpha channels will make always black. Media players will always play a movie with a black background with alpha channel. If you want a yellow background, you will need a solid yellow or yellow shape on the bottom of your model layer.

• Calls from [email protected] / * / ip addresses

  Hello world

  I get calls from [email protected] / * / IPS on my Highway VCS trying to dial different numbers. I activated a policy rule of local call to reject asterisk@.* to any destination. * but it does not work and I still get the call attempts.

  Someone has encountered this and knows how to stop these calls?

  Thank you

  Maciek

  Maciej,

  try to replace 'origin' with 'non-authenticated-origin' in your CPL, so that it reads as follows:

  CPL 'origin' field has a value of "is not far" If the message that the CPL is run for is not authenticated.

  You can find more information about the field of the 'non-authenticated-origin"in the VCS administration guide.

  Hope this helps,

  Andreas

• VCS - C leave IP address directly with VCS - E also

  Hello

  I have a VCS - C with a VCS-E in an environment x7.0

  The majority of endpoints are registered on the VCS - C, but there are some points of endpoints that are not for specific reasons.

  Endpoints are not registered in the VCS - C can call termination points registered by its IP address, but the end point registered can not dial end points unregistered. I understand that this is normal with the indirect numbering and the VCS-E but y at - there a way around this direct IP activation on the VCS - C and the use of a search rule that everything that does not correspond to a 10. hit the VCS-E?

  I'm doing a lab to do the test but would be great to see some comments on this.

  Thank you

  Hello

  You can work around this by creating a subarea on the VCS - C with one or several partners subzone composition one or several rules of type "Subnet", where you set of these endpoints unregistered IP addresses/ranges.

  This will have the effect that when registered endpoint contains an IP address appearing in one of this subarea subnet-type membership rules, the VCS - C will consider the known IP address and continue to attempt to place the call to that specific IP address.

  It will be easier for you if these unregistered end points were easy to define subnet membership rules, for example if they are all in the same subnet, rather than spread around different subnets, without overlap.

  -Andreas

• Change caller id / name of the SIP URI of VCS calls

  Hello

  I have clusted CUCM 9.1 with a SIP to a VCS - C trunk.  When making calls, the calls show a caller id of [email protected] / * / address, for example [email protected] / * /.  I have a configuration URI directory on the phone that generates the call, but now it shows the URI.  Incoming calls from SIP URI properly.

  Thank you

  Hello

  On the trunk SIP for VCS, under outgoing calls, there should be an adjustment: vocation and connected part format, change it to URI deliver only partially connected. Also, under the profile SIP assigned to the SIP trunk to VCS, there should be a setting use entirely field in queries, check this box. The SIP profile should also be attributed to the device SIP calls.

  HTH, if yes, please rate.